Related
Ok, so I know this will eventually get buried in the forums but I thought I would attempt to give a little basic info here. Right now the QA section is flooded with people that have flashed and are now soft bricked (have problems but can recover) or hard bricked (have problems and cannot recover). I'm hoping that I can help some people prevent these issues to an extent.
Terminology, the differences in my opinion.
Soft brick- Your flash didn't go right, something went crazy, etc, but either way you can't boot, stuck at ATT logo, boots into recovery no matter what, boots to phone--!--pc, BUT, your hardware buttons work or ADB works and you are able to boot into DOWNLOAD mode.
Hard brick- Your flash didn't go right, something went crazy, etc, but either way you can't boot, stuck at ATT logo, boots into recovery no matter what, boots to phone--!--pc, BUT, your unlucky and hardware buttons do not allow access to DOWNLOAD mode or ADB is not downloading.
Also, after a new flash or flash to stock, it's a good idea to immediately enable USB debugging. Menu, Settings, Applications, Developement, check the box for USB debugging. It will make things easier later on.
1. First. BEFORE you flash, can you access download mode with your buttons??? Test it.
3 Methods.
Method 1: (ADB - from recovery or normally booted with usb debugging on)
Open a cmd prompt/console/shell
adb shell
adb reboot download
Method 2: (KEY COMBO)
Remove the battery, sim card, sdcard if you have one
Insert the battery
Hold Volume Up + Volume Down + Power
Method 3: (KEY COMBO)
Remove the battery, sim card, sdcard if you have one
Insert the battery
Hold both Volume buttons (from i9000 just down, don't touch the power button)
Plug in the USB cable and continue holding both Volume buttons
If not, use designgears fix. http://forum.xda-developers.com/showthread.php?t=812434
2. Second. Download the SDK, drivers for your PC, and learn some basic ADB commands, ie, adb reboot download, adb reboot recovery, adb shell. Here's my quick guide. ADB can be used when the OS is running, when in recovery, and when stuck on ATT boot screen.
Here's what I do. After you download the sdk and unzip. There is a folder called tools. I copy that to c:
Then open a command prompt and type,
C:
CD tools
Then issue adb commands.
adb reboot, adb reboot download or whatever command you need.
Of course make sure your phone is connected via USB and debugging is enabled.
Here's another method for using adb.
1) start-> run-> sysdm.cpl
this will start the system properties. you can reach this from right clicking "My Computer" and hitting properties. Windows 7 though is different. The above method is most universal.
2) Move to Advanced Tab that pops up. From there click the "Environment Variables" button.
http://wtfokc.com/sef****/sysdm-1.gif
3) In the window that pops up, find the "PATH" area in the "System Variables" listbox at the bottom:
http://wtfokc.com/sef****/sysdm-2.gif
4) Click edit again, put in path to the AndroidSDK tools folder. Do it like shown otherwise you can biff something up. DO NOT REMOVE ANYTHING. Just add a SEMICOLON ( ; ) to the last of the line that's already there, then the path to the folder.
http://wtfokc.com/sef****/sysdm-3.gif
5) If on Win7 you shouldnt have to reboot. XP however will. Then you are set. You can now just load a CMD prompt and do ADB without having to CD TOOLS.
3. Third. Install Clockwork Recovery! Root your phone and download ROM Manager from market. Install Clockwork recovery from ROM Manager. BOOT into recovery to make sure it works. You will have to choose reinstall packages from stock recovery. What ROM Manager does, it put an update.zip on the root of your SDcard, then when you choose reinstall packages from stock recovery it install update.zip. I personally leave the update.zip file on my sdcard at all times, just in case.
Once you have clockwork installed, make a Nandroid backup of a good running rom. In case something happens, if you can boot into recovery, then you can possibly restore your nandroid to at least get you up and running quickly, and without the need of a pc.
NEW Info!!! You can recover from a hard brick, maybe. Here's how to create a USB Jig to reproduce the button download mode for you folks who don't have it.
http://forum.xda-developers.com/showthread.php?t=841512
Here's another thread about the USB Jig method.
http://forum.xda-developers.com/showthread.php?t=819551&highlight=USB+jig
If my captivate was one that had the missing button recovery/download out of the box, I would probably know how to make a USB jig or have one already before flashing. Even with the 3 button fixes that are out, it looks like some people are still bricking.
****Disclaimer****
This is just from personal exprience. I have flashed most roms available, and I have experienced every variation of soft brick mentioned above and have recovered.
I find that being able to get your phone into download mode and knowing how to use Odin will be your 2 biggest life savers after something bad happens.
This will not keep you from getting a bad flash or something else, but having this knowledge ahead of time may help you recover from issues more quickly and without asking a question on the forums that have been asked dozens of times.
Also, personally, if I cannot perform step 1, access download mode with buttons, I personally would be VERY cautious about flashing! ADB reboot download is nice, but if you are stuck at ATT logo or phone--!--PC mode then ADB doesn't work, YOU HAVE TO USE BUTTONS.
Just my 2 cents, take it or leave it.
Edit. Added some new info to post. Thanks for extra info guys. I'll mirror the links to the images later when not at work.
+sticky
excellent write up. a must-read for anyone even thinking about flashing
Original Post updated to add my information
bobbylx said:
ADB reboot download is nice, but if you are stuck at ATT logo
Click to expand...
Click to collapse
Ok first off something that should be added to this is always may sure you have usb debug mode Settings>Applications>Development>USB Debugging enabled on your phone. Don't take it out of debug mode. This will allow you to issue adb commands if you have.
If you are getting to the att logo screen and not beyond that and you have debug mode enabled then you can use adb to reboot into either recovery or download mode.
Steps
1: Get the command prompt up and que up the adb command you want to issue either reboot download or reboot recovery. Don't press enter yet.
2: When the att screen comes on your pc should make a notification sound that the device is connected.
3: On the second notification sound issue your adb command and the phone will reboot into the mode you selected.
Mileage may vary but should work.
This has saved me a few times.
STICKY
Sent from my SAMSUNG-SGH-I897 using XDA App
Thanks for the extra info. Malfuncion, awesome write up with pics, I'll add to first post later. I always forget about adding a system variable.
Sparker366, thanks, I always thought that at the ATT screen adb didn't, but you know what, I never tried.
I figured since I'm not a dev and don't have that knowledge I would try to help start this up to contribute a bit. And honestly, if you hop over to the QA sections there are so many threads that could be solved by knowing this info ahead of time. I doubt everyone will read it, but I hope it helps the ones that do.
bulletproof1013 said:
STICKY
Click to expand...
Click to collapse
+1
This is my first smart phone and first experience with Android. I also don't have any experience with linux. Fortunately, I was able to avoid problems when I first started by reading, reading, reading. This type of information would have been invaluable. In fact, the tip on keeping debug mode on all the time is great to know, and I never saw that before.
Sent from my SAMSUNG-SGH-I897 using XDA App
This thing is getting buried in the BS posts....BACK TO THE TOP!
definitely sticky
Bump Bump Bump
Great Info
Updated original post with extra info.
Shameless bump here. New version of Cog uploaded, so that means there will be questions soon.
Thanks, great info.
FWIW........
I feel like I am of average intelligence, and would think I could nail download mode everytime by the 3 button method, but damn if it is hit and miss for me every other time.
One way I found (I didnt discover it, but read it somewhere) to nail it EVERYTIME is to remove sd and sim. Plug the usb to the phone AND THE PC, while odin is sitting and waiting. Then while holding both up and down volume buttons, insert the battery. It works every time with no fuss.
Thanks for the post, my vote for sticky as well.
+1 sticky
Sent from my SAMSUNG-SGH-I897 using XDA App
Moving this to the top. More questions in QA that can be helped by reading these tips first.
I would also suggest that anyone who wants to flash actually test their phone's USB transfer ability before flashing.
The best way is to find a large file, perhaps one just under 2G in size and transfer it to the internal SD storage.
Test md5 checksums on the source and this file and make sure these match.
(you can use the 'md5sum <filename>' command from the terminal app, from Windows you can use a md5sum port for the source file win32 md5sum).
This will ensure your USB connection is stable enough for long, error free transfers to the phone.
Also important: it's useful to disable any powersave actions on your PC while using an app like ODIN.
Sorry all, moving this to the top. There are about 6 or 7 bricked phone Questions in Q & A now.
Awesome, clear and concise. Been trying to figure out how to make nandroid backups and this explained it very simply Thank you!
thanks for the reminder
there's so many steps to install a rom...
specially with download mode keycomb, i tend to not to remove sim and memory card cuz i dont want to lose or damaged my mcard. now i will remove each time!
another good reason flashing stock with odin before flashing new rom
I would also say its a good idea to back up your efs folder. Mine got all borked up when that jpc rom came out a while ago and it is a ton of work to fix. Sgs tools copies your nvdata.bin and. /nvdata.bak files to your sd card if you do a product code check. Or you can use root explorer.
hi guys.. could you help me with my problem.!
I have an LG GT540 android 1.6 firmware version(stock)
So here are my problems:
1. I tried to upgrade it from 1.6 to 2.1 using this tutorial http://forum.xda-developers.com/show...27&postcount=3 thanks to lavero.burgos for posting it, I was successful at first part, but I cant follow the next because my device wont go to fast boot,, I tried putting it off, then camera+poweron but it doesnt do anything. It doesn't light, no lg logo appears, just nothing although the computer can read the drive when I connect it through usb. So I cannot flash it to 2.3,2.3 because it just wont go to fastboot.
2. When I turn it on normally, It takes long before it response like after 30sec to light, but just light, no lg logo appears although it wasnt bricked because I can use it normally after just waiting to on.(annoying)
3. Since I upgraded it to 2.1, I lost all 3rd party application and the internal apps were the only left, so I copied all my saved apps (.apk) to my sd card but the problem is there is no saved app on my phone to read and install those apps from my sd card.(irritating)
4. My device wont read my sim card, when I start it it says "sim card unprovisioned" so basically I cant connect to mobile networks here in the philippines(im using globe telecom). I feel that Im stucked in the middle of nowhere since I cannot contact and txt all my family and friends.
5. I cant connect to wifi,, when my device detects wi-fi, I try to connect to it but from the log it only try to connect but doesn't obtain the ip address. Even when the wi-fi signal is strong, it does the same thing.
So please help me guys,,I want to hear from my fellow xda-developers badly,,,
PS. also those who have problems with their LG GT540 pls feel free to post and share it with us here... thank you all guys in advance....
hi so let me get it right the phone is working (can turn on and use but cant call) yes? hmmmmm..... try this
MUST DOWNLOAD THIS DRIVERS!!!!
http://dottech.org/android/26188/usb-adb-and-fastboot-drivers-for-windows-for-all-android-phones/
Step one!
1.turn off phone.
2.hold the POWER button till you feel the beep.
3.let go of the POWER button when you feel the beep and hold onto the CAMERA button only.
4.hopefully it turns on to a blackscreen and nothing else(fastboot)
5.unzip this CLICK ME!! to desktop and open the flash all no wipe file
or......
1.turn on your phone.
2.go to settings>applications>development>tick the usb debugging
3.connect phone to computer (make sure phone is on)
4.unzip this CLICK ME!! to desktop and open the flash all no wipe file
5. phone should boot into blackscreen like the one above......
Click to expand...
Click to collapse
Step 2!
both should flash a recovery image. Next
1.make sure the phone is off
2.press POWER button
3.when you feel the beep let go of POWER button and press the HOME button only.
4.phone should boot into recovery mode.
5.take out battery again
6. download a rom into the sdcard using computer
7.go to recovery again using the steps above (steps 1 to 4)
8.select wipe all data factory reset or something like that....
9.install zip from sdcard
10.select from sdcard
11.choose the file you downloaded
12.finish flash and reboot phone.
Click to expand...
Click to collapse
excellent guide! big thanx
bs828 said:
hi so let me get it right the phone is working (can turn on and use but cant call) yes? hmmmmm..... try this
MUST DOWNLOAD THIS DRIVERS!!!!
http://dottech.org/android/26188/usb-adb-and-fastboot-drivers-for-windows-for-all-android-phones/
Click to expand...
Click to collapse
Thanks,, Ive tried the 2nd option on step one and i think my phone successfully got to fastboot(just clean blank screen) so the cmd automatically run and states
C:\Desktop\adb rebootloader
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
error: protocol fault <no status>
C:\Desktop\fastboot flash recovery recovery.img
< waiting for device >
Did I miss something???
ok try again this time with the phone turned on. and then run the script and did you install the drivers?
bs828 said:
ok try again this time with the phone turned on. and then run the script and did you install the drivers?
Click to expand...
Click to collapse
yeah I installed the drivers...
hmmm maybe there are no fastboot drivers(main suspect....) there are a few ways to get it but for mine i just plug my phone in to my pc (windows 7 64bit) it just recognize it and tries to get the "google fastboot interface" drivers from windows update...
Try Volume Up+Search Key+Power to go into Fast boot Mode, There's different keys to activate Fastboot Mode (There is different versions of Fastboot)
Sent from my LG GT540 CM9 PreRC Polish Blood using xda premium
Your phone is/was bricked
Hey, I'm sorry to bing back such an old thread, but I just wanted to say this for posterity: your phone has/had a soft-brick. This means: you can't see Android nor LG boot logos, can't enter Recovery and (maybe) can't access Fastboot, but I'm not too sure on that last one. Besides that, the phone works "okay", but you should try to fix it.
Basically this soft-brick is almost always caught when upgrading from 1.6 to 2.1, so everyone should have it, including me. It took me a whole year to realize how to friggin' fix it lol, but here goes what I did:
Thanks for your help everyone, I came to a solution after a full year lol. Here's my enlightenment, from another Thread:
------------------------------------------------------------------------------------------
Just wanted to leave my 2 cents here, I've been trying to do my best since around august 2014, no success. 2 days ago I retried this, and I DID IT! I will tell everyone what I did very shortly:
My problem that I solved: I can boot, device works like a charm. But: no boot logos, no recovery.
My solution for TL;DR: UNINSTALL ALL DRIVERS FROM DEVICE MANAGER 1ST, then reinstall. After that, flash a fastboot ROM and use it to WIPE ALL THE DATA IN YOUR PHONE! THIS was what I needed and was never explained: you had to WIPE the old data in order to get the boot screens back.
IN THIS ORDER (THANK YOU to those people from previous replies, gathering all your info was of great value):
Uninstall all of your phone drivers from your PC!!! This is what made most of my headaches go away, just use Device Manager and uninstall anything from LGE. After that, plug in your device in your USB ports (always BACK ports, not front ports, important). It should detect all drivers and download them.
IF it fails (it generally does with LGE USB Modem), you can go to Device Manager > Unknown Device (the one that wasn't recognized) > Right Click and Update > Choose 2nd option, then choose "choose from a list of local controllers" (or whatever the button says). After that, scroll down to LG Electronics, Inc. and install what didn't install.
I also found these drivers, but I did not test them: http://www.mediafire.com/download/p693hcz6kkouh19/USB_Driver_LG_GT540.zip
Huzzah!
Now you're set to begin:
FIRST thing you wanna do is a factory reset, this is something I'd forgotten with time, don't make the same mistake as I did. You can do it by turning your phone on and pressing Volume +/- & Home & Quick Search buttons all together for 5 seconds (it works, be patient and wait for it, even if you open the camera or any other stuff).
Download this Google SDK Tools (unzip and put the folder in C:\ drive) and this Fastboot drivers for GT540 (unzip and put the files inside the folder in C:\android-sdk).
Skip this next line if you know your ROM has fastboot.
Now, if you don't have a ROM with fastboot, I recommend you use either European Open+Fastboot or V20C Orange France Fastboot ROM.
Click to expand...
Click to collapse
Since you have Fastboot enabled, now all you need to do is turn off your device (all this with its battery on it, no weird things) and hold the Camera button before turning it back on. This should take you either to a black screen, or simply to no display, like me. Either one will work anyways.
Now press the Windows key > Type cmd and open it with Right Click > Run as Administrator.
In it, type all this, command by command (you can paste by right clicking):
cd C:\android-sdk
fastboot -w
fastboot erase boot
fastboot erase system
fastboot -w
fastboot reboot
Click to expand...
Click to collapse
And now it's go time! Do what everyone else says in here: Take out your phone's battery, SD and SIM cards, fire KDZ Updater up as Administrator (If your KDZ freezes, then it's either faulty or you did not install msxml, look for a good KDZ that comes with that file and delete your current one), choose CS_Emergency PhoneMode and:
1-Plug your phone while holding the volume DOWN button (don't worry! My phone didn't show "Download Mode" either, if you hear the Windows "Somethingpluggedin" Bump noise, it's ok).
2-Flash French V20A
3-Unplug your phone once KDZ says "==FINISHED==".
4-Plug it once again, holding the volume DOWN button.
5-Flash out.kdz (remember! it's CS_Emergency).
Click to expand...
Click to collapse
THANK YOU XDA!
--------------------------------------------------------------------------------------
Also, if you look in here you'll find how to flash an awesome ROM, Cyanogen Mod 10 (should say "Final Version#2).
I went to update to KitKat and it was nearly done and then the "No Command" error came up. My tablet has an unlocked boot loader but isn't rooted. However it was before but I updated it from an OTA and that got rid of it. I've tried booting into recovery etc but the same thing happens.
Anyone have any advice please?
Same exact issue and set up here. Also, maybe I'm just dumb, but I can't get my tablet to turn off either. It just keeps cycling back to the "no command" screen until I do something.
tgearhar said:
Same exact issue and set up here. Also, maybe I'm just dumb, but I can't get my tablet to turn off either. It just keeps cycling back to the "no command" screen until I do something.
Click to expand...
Click to collapse
I think that both of you what you see (the "no command") is your stock recovery, if indeed you see an android with a yellow !.
If it is the case to access the menu of the stock recovery press power and tap volume up. The menu will give you the choice of rebooting your Nexus 7.
gunner1937 said:
I think that both of you what you see (the "no command") is your stock recovery, if indeed you see an android with a yellow !.
If it is the case to access the menu of the stock recovery press power and tap volume up. The menu will give you the choice of rebooting your Nexus 7.
Click to expand...
Click to collapse
I can get to the menu but when trying the reboot option, it just cycles the same way again. Back to the android with a red ! and says "No command." I also tried clearing cache and data to no avail. I was going to try using ADB to manually push the update but my computer was recently updated and now I can't get the driver installed for some reason.
I spent too much time messing around with and learning how to do things with my SIII and not enough time with this
Same deal here! Not sure what to do short of wiping and losing my info.
Same here...any advice? Not sure what happened. OTA update too.
Significa said:
Same here...any advice? Not sure what happened. OTA update too.
Click to expand...
Click to collapse
Wow, this seems to be widespread, at least somewhat. I'm in same situation. Toolkits, adb, nothing works. I thought this was a soft brick, but now I'm thinking it's toast. Probably doesn't help that I didn't have Dev options enabled along with USB Debugging. I can't even turn it off. Just bootloops after Google logo shows up twice, then to No Command error, then starts over again. I wonder what the hell is causing this. (Device was locked and unrooted)
Same boat here, even sideloaded the factory image via ADB.
[QUOTE [/QUOTE]
I was going to try using ADB to manually push the update but my computer was recently updated and now I can't get the driver installed for some reason.
If you have android-sdk-windows installed on your computer do not forget to update it through "SDK Manager.exe".
Pushing via ADB didn't work for me. That also failed.
I caved and called Google. Tech support is stumped as well.
Sent from my Nexus 5 using Tapatalk
Could this be a widespread issue? Like I don't even understand why it happened at all!
Sent from my Nexus 5 using XDA Premium 4 mobile app
I finally got mine working again!
I tried a million different things so I'm going to try and explain my process as simple as I can, I apologize in advance because I am far from an expert...
First, I tried using the method, well some of it, from this thread: http://forum.xda-developers.com/showthread.php?t=1907796
- I would suggest using this thread to get everything set up (drivers, ADB, the factory image downloaded and in the correct file location) I wasn't able to get the drivers working correctly with that route so I ended up using the toolkit to get them working but that thread helped me get all of the system files in the correct location and helped get all of the ADB stuff set up.
Once you have everything set up and your computer recognizes the tablet, (I checked that by opening a cmd prompt and using the command from the original thread above "adb devices"). As long as you see your device, I think you should be good.
From the "No Command" screen I held down Power and Volume + to get the menu to come up. I then chose the Restart option and immediately held Power and Volume -. This got me into the Fastboot Mode.
Once in Fastboot mode I went to the cmd prompt on my computer and used the following commands in this order from this post:
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot erase system -w
fastboot flash system system.img
fastboot reboot
*Make sure that all of the image files are in the proper location on your computer otherwise this step is worthless
The tablet then rebooted normally and I was able to set everything up again. Again, I am by no means an expert at all, this is just what worked for me. Try at your own risk.
I hope I covered all of the steps, I tried a million different things last night so they all kind of run together.
I ended up doing and it worked for me as well. Wiped everything though. How can I restore / reinstall my apps w/o needing to download them all again?
Two things: That guide says you must have USB Debugging enabled. Since my wife had this tablet, I did not have dev options enabled at all, including USB debug.
The other thing is that when I run the SDK Manager, nothing happens on my computer. I double click it or try Run as Admin, and a small CMD box flashes on my screen for a millesecond and disappears. That's all.
My wife's 2012 N7 is having this same problem. Unlocked bootloader, but I reflashed factory image and unrooted before giving it to her. She got the OTA last night, and now stuck at No Command.
I've subscribed to this thread, hoping that you guys will have it solved before I get home from work tonight! Would love to not have her lose all her data.
(I was kinda mad that she got the OTA last night and I haven't got it yet on my 2013 N7, but that's another gripe for another thread)
killswitch11 said:
Two things: That guide says you must have USB Debugging enabled. Since my wife had this tablet, I did not have dev options enabled at all, including USB debug.
The other thing is that when I run the SDK Manager, nothing happens on my computer. I double click it or try Run as Admin, and a small CMD box flashes on my screen for a millesecond and disappears. That's all.
Click to expand...
Click to collapse
Unfortunately I'm not sure on the SDK manager part. As far as the USB Debugging, I'm 98% sure that I did not have it enabled either. I think I did at one point but after doing several OTA upgrades, I'm sure it got unchecked.
---------- Post added at 01:34 PM ---------- Previous post was at 01:01 PM ----------
kr33mo said:
I ended up doing and it worked for me as well. Wiped everything though. How can I restore / reinstall my apps w/o needing to download them all again?
Click to expand...
Click to collapse
I don't believe there is a way. Maybe someone smarter than myself can chime in but I had to let the play store do it's thing and re-download all of mine.
tgearhar said:
I finally got mine working again!
I tried a million different things so I'm going to try and explain my process as simple as I can, I apologize in advance because I am far from an expert...
First, I tried using the method, well some of it, from this thread: http://forum.xda-developers.com/showthread.php?t=1907796
- I would suggest using this thread to get everything set up (drivers, ADB, the factory image downloaded and in the correct file location) I wasn't able to get the drivers working correctly with that route so I ended up using the toolkit to get them working but that thread helped me get all of the system files in the correct location and helped get all of the ADB stuff set up.
Once you have everything set up and your computer recognizes the tablet, (I checked that by opening a cmd prompt and using the command from the original thread above "adb devices"). As long as you see your device, I think you should be good.
From the "No Command" screen I held down Power and Volume + to get the menu to come up. I then chose the Restart option and immediately held Power and Volume -. This got me into the Fastboot Mode.
Once in Fastboot mode I went to the cmd prompt on my computer and used the following commands in this order from this post:
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot erase system -w
fastboot flash system system.img
fastboot reboot
*Make sure that all of the image files are in the proper location on your computer otherwise this step is worthless
The tablet then rebooted normally and I was able to set everything up again. Again, I am by no means an expert at all, this is just what worked for me. Try at your own risk.
I hope I covered all of the steps, I tried a million different things last night so they all kind of run together.
Click to expand...
Click to collapse
Worked for me! Thanks, I don't believe I had USB Debugging enabled either. Shame it wiped all my data though.
OK, got mine back up and running! I'll just leave what I did here in case anyone can benefit from it.
I first used Wug's Toolkit to download and install the RAW drivers. (Option #4, I believe) They were the only ones that worked for me. I followed the instructions to install them and then when it looped to the No Command screen, I held volume up and power. This got me to the menu, where I chose reboot. I then immediately held down the volume button and power to get into the bootloader screen, where it (thankfully) stopped looping. Then I unlocked the bootloader using the one-click option. Next step was to download and flash factory 4.4 image using the Soft Brick mode. Fastboot recognized my device and pushed the image. Now all is well. Close call... I've already enabled USB Debugging for my wife on this tablet so that crap doesn't happen again. She did lose all her data but she is happy to have a working tablet again instead of a $200 beer coaster.
killswitch11 said:
OK, got mine back up and running! I'll just leave what I did here in case anyone can benefit from it.
Click to expand...
Click to collapse
Worked for me as well. Really appreciate that.
Sent from my Nexus 5 using Tapatalk
killswitch11 said:
OK, got mine back up and running! I'll just leave what I did here in case anyone can benefit from it.
I first used Wug's Toolkit to download and install the RAW drivers. (Option #4, I believe) They were the only ones that worked for me. I followed the instructions to install them and then when it looped to the No Command screen, I held volume up and power. This got me to the menu, where I chose reboot. I then immediately held down the volume button and power to get into the bootloader screen, where it (thankfully) stopped looping. Then I unlocked the bootloader using the one-click option. Next step was to download and flash factory 4.4 image using the Soft Brick mode. Fastboot recognized my device and pushed the image. Now all is well. Close call... I've already enabled USB Debugging for my wife on this tablet so that crap doesn't happen again. She did lose all her data but she is happy to have a working tablet again instead of a $200 beer coaster.
Click to expand...
Click to collapse
I'll give that a go tomorrow. Missed my tablet! Hope it works!
A bit of an SOS situation if anyone knows the right steps please
Well, I restored a Titanium Backup and mistakenly toggled the "restore system apk". It ran fine, all restored and then when I rebooted got stuck.
By "stuck", it re-boots constantly. It shows the LG animation, then all I can see is two messages before it starts booting again:
1) "Unfortunately, Google Play Services Has Stopped"
2) "Unfortunately, System UI has stopped
... and then it does the entire boot sequence, animation, again, and again.
Here is what I can do:
* It is in USB debug mode.
* I have drivers on laptop
* I am able to connect with adb and also shell into phone.
* With adb, I have output to the file an "adb bugreport" as well as an "adb logcat".
* I have several backups:
a) The modemsst1.img and modemsst2.img created by Titanium Backup
b) Titanium backups (full apps and data)
c) an "adb backup - all" backup
* I managed to get it into firmware update mode by pressing the volume up button and the power button and then when it flashed red a few times, just the up button. So, I can get it into Firmware update mode.
Of course, I have never really used adb before, except to dabble a bit. So, I am encouraged that I can somehow get into with shell.
I am not unplugging it until I know what to do!
Since then I have been able to turn the phone off and also put it into charging on USB.
This is what worked:
* Hold down power and volume down button until booting stops and phone turns off completely.
When it does shut down, I kept buttons down until it flashes logo again and then shuts down again. Then I let go. Phone is off and when I plugged in the charger it shows charging animation.
Now, after inspecting the bugreport, I noticed a lot of these messages for all the system apps like this one:
"I/PackageManager(21318): Expecting better updatd system app for com.lge.sizech"
I think the cause of all this shralp is this, I did a LG Mobile Support Tool "Upgrade Recovery" and then in Titanium Backup I restored an older backup (incl system apks). At least that makes sense seeing all the "Expecting better apdat system app" messages in the bugreport.
Still not sure what to do next
I tried the very good instructions here:
[Guide] Unroot/Unbrick - flash official factory firmware with LG Launche
http://forum.xda-developers.com/showthread.php?t=2471370
The update succeeded. However, when I rebooted the phone it is in the same boot-loop with message that it was before.
I used the BELL D803B10D_00.kdz file. Now I will try with the earlier version BELL D803BA_00.kdz file.
We will see what happens ...
do you have nandroid backup from previous rom?
I have three backups:
1) Titanium Backup (full)
* This was my first backup performed right after rooting device and installing Titanium Backup.
2) Titanium Backup (full)
* Did this 2 days ago. Device was working OK and did as precaution.
3) ADB BACKUP. I did this one before my Titanium restore.
I restored the first titanium backup and that (ooooppps!) was after I did an LG Firmware update.
ALSO:
I am on Windows 7 64 and although adb works fine, fastboot does not. I understand that might be a problem with windows 7 64.
So, unless anyone objects, I am going to redo on my windows 32 machine and also "fastbook oem unlock".
Since firmware is OK, if I do the fastboot oem unlock, that will wipe everything. But I can still boot and re-setip the phone, right?
Just checking before I fudge everything up here ..
ALSO ALSO:
I had antivirus/theft security installed and I disabled it partway through last restore.
Maybe that has somethng to do with this all .
But I am still cool because I can ADB and also firmware install seems ok.
ADB works and that is the one good sign.
or you can follow ADB Sideload method
http://forum.xda-developers.com/showthread.php?t=2318497
zekurosu said:
or you can follow ADB Sideload method
http://forum.xda-developers.com/showthread.php?t=2318497
Click to expand...
Click to collapse
I don't (didn't) have TWRP installed. How can I sideload without it?
Also, should I adb oem unlock to get it wiped at this point?
I'm having a similar problem on a Bell D803. Just happened very randomly today. I turned my phone off for an exam, then turned it back on after.. initially had no signal and a black background. Settings for factory reset wouldn't work. My phone is rooted and has TWRP. I went into recovery and formatted.
Bootloop.
Bootloop.
Bootloop x 20.
I however, don't get the same two messages. I just keep bootlooping.
Got home, tried to go through download mode to unbrick it, but for some reason my computer isn't picking it up. I have all the drivers, and before this incident, it was recognized.
Any solutions?
I'm thinking of buying an OTG USB and then just flashing a stock zip from recovery. Would that be a possible viable solution?
asdfvtn said:
I'm having a similar problem on a Bell D803. Just happened very randomly today. I turned my phone off for an exam, then turned it back on after.. initially had no signal and a black background. Settings for factory reset wouldn't work. My phone is rooted and has TWRP. I went into recovery and formatted.
Bootloop.
Bootloop.
Bootloop x 20.
I however, don't get the same two messages. I just keep bootlooping.
Got home, tried to go through download mode to unbrick it, but for some reason my computer isn't picking it up. I have all the drivers, and before this incident, it was recognized.
Any solutions?
I'm thinking of buying an OTG USB and then just flashing a stock zip from recovery. Would that be a possible viable solution?
Click to expand...
Click to collapse
Well, I am able to connect with adb fine on my laptop (Win 7 64) but not on my desktop (Win 7 32)
But on my Win 7 64 I cannot get into fastboot.
I am wondering if the driver install on my desktop went foo-bar and needs reinstall. Also, I noticed that the website drivers are more recent USB drivers than some of the ones linked on this site.
I used adb uninstall package for many user packages and it was success. But I still see the packages listed in the bugreport?
For example: I already uninstalled "com.benhirashima.skiplock" and also "com.lookout".
Why? What to do to really zap them for good?
Sorry, I posted the wrong link earlier.
This was the guide I used which succeeded but made no difference to the boot-loop.
LG G2 Stock Firmware (Go Back to Stock)
http://forum.xda-developers.com/showthread.php?t=2432476&highlight=d803
Just figured out how to do a factory reset.
http://www.youtube.com/watch?v=3ogBvzbPikc
The hard reset worked and now I am configuring the phone settings!
So, again, this is what I did:
1) http://forum.xda-developers.com/showthread.php?p=45293512
2) http://www.youtube.com/watch?v=3ogBvzbPikc
Not sure if it all worked but I am setting the phone up as we speak (or as I type)
natureburger said:
Well, I am able to connect with adb fine on my laptop (Win 7 64) but not on my desktop (Win 7 32)
But on my Win 7 64 I cannot get into fastboot.
I am wondering if the driver install on my desktop went foo-bar and needs reinstall. Also, I noticed that the website drivers are more recent USB drivers than some of the ones linked on this site.
Click to expand...
Click to collapse
Hmm that's strange. Unfortunately for me, I'm already on 64-bit and it still isn't picking it up.
ALL FIXED UP
WORKING 110%
:good:
natureburger said:
ALL FIXED UP
WORKING 110%
:good:
Click to expand...
Click to collapse
I have followed this to a t.
Succesfully flashed the stock firmware that came with the phone when sold.
Did hard reset using the the power button and volume down
= phone rebooting every 10 seconds, no wifi, imei = null
adb devices = offline.
Really depressed right now. If anybody can help me I would appreciate it.
zprovo said:
I have followed this to a t.
Succesfully flashed the stock firmware that came with the phone when sold.
Did hard reset using the the power button and volume down
= phone rebooting every 10 seconds, no wifi, imei = null
adb devices = offline.
Really depressed right now. If anybody can help me I would appreciate it.
Click to expand...
Click to collapse
Press the power button down and hold it.
It should turn off, then look like it is turning on, (flash logo very briefly) and then turn off.
Let go of power button and it should stay off.
Do that. Now, does it work to turn off completely?
Let's see if you can do that first.
Then .. do hard reset, exactly like this:
http://www.youtube.com/watch?v=3ogBvzbPikc
Does the hard reset screen show and give you hard reset options?
natureburger said:
Press the power button down and hold it.
It should turn off, then look like it is turning on, (flash logo very briefly) and then turn off.
Let go of power button and it should stay off.
Do that. Now, does it work to turn off completely?
Let's see if you can do that first.
Click to expand...
Click to collapse
Yup. I totally understand what you are saying and have done it many times. I had to use that method to get into download mode and also had to use it to do hard reset.
I just reflashed the phone all over again a second time succesfully.
Reboots every 5 seconds. Keyboard came up for a few seconds for the first time in 48 hours during the initial setup phase. 5 seconds later as I was trying to input a wifi code it would not appear. then it rebooted as usual.
I really appreciate any input right now. :cyclops::crying:
zprovo said:
Yup. I totally understand what you are saying and have done it many times. I had to use that method to get into download mode and also had to use it to do hard reset.
I just reflashed the phone all over again a second time succesfully.
Reboots every 5 seconds. Keyboard came up for a few seconds for the first time in 48 hours during the initial setup phase. 5 seconds later as I was trying to input a wifi code it would not appear. then it rebooted as usual.
I really appreciate any input right now. :cyclops::crying:
Click to expand...
Click to collapse
1) Are you able to completely turn it off using my instructions?
2) When you hard reset (2nd half of this video), http://www.youtube.com/watch?v=3ogBvzbPikc
a) Does the hard reset screen show?
b) Does it give you the hard reset options?
3) Before it was bricked, was it in 'usb debug mode' in developer options?
4) Which kpz version did you restore to?
5) Did your "adb devices" ever work? Did your "adb shell" ever work?
natureburger said:
1) Are you able to completely turn it off using my instructions?
2) When you hard reset (2nd half of this video), http://www.youtube.com/watch?v=3ogBvzbPikc
a) Does the hard reset screen show?
b) Does it give you the hard reset options?
3) Before it was bricked, was it in 'usb debug mode' in developer options?
Click to expand...
Click to collapse
1) Yes absolutely. It is sitting next to me right now doing nothing at all because I turn it off when I am not trying to fix it, otherwise it keeps rebooting relentlessly.
2) a) Yes, same as the video. b) Yes it says the same exact thing as the video. I press power key twice and it begins. The stock recovery android appears with a loading bar on the bottom for ~1 minute then it goes to the boot "lg animation".
3) Yes it was. Before it was bricked I essentially always had it in debug mode because I successfully rooted it and simply left it on debugging mode after having to activate it to root.
4) D801V11B_00.kdz The EXACT same as the original. This is a Videotron (canadian) phone. I can clearly remember without a doubt going into about phone and this is what it was running before all of this happened.
5) I am having a bit of memory strain here, but I do believe it also said adb devices before any of the issues came. It is a good point I will try "adb device" from another trusted computer.
Other notes: I can browse the android os for a few seconds. Sometimes sound does not work, wifi is non functional (even though the keyboard never appears, I managed to have a security free wifi in my proximity and it would not connect (was saying: temporarily avoiding bad signal)) and also I do have modemstat1.img and modemstat2.img backups for EFS.
adb devices consistently shows "offline" but it is definitely recognizing the phone. I have also tried using usb debugging activated and still "offline". Drivers are up to date and all.
The upper drawer in the usual g2 user interface is strange now. it doesnt have anything except for the date (1970 something...) and a "gear" icon for system settings. I am talking the drawer you drag down from the top of the screen.
This phone was working with absolutely no problems 2 days ago.
Thank you so much for looking into this. I have certainly exhausted my repairing capacities. I am entirely dependent upon the knowledgeable individuals in here from here on out.
zprovo said:
1) Yes absolutely. It is sitting next to me right now doing nothing at all because I turn it off when I am not trying to fix it, otherwise it keeps rebooting relentlessly.
2) a) Yes, same as the video. b) Yes it says the same exact thing as the video. I press power key twice and it begins. The stock recovery android appears with a loading bar on the bottom for ~1 minute then it goes to the boot "lg animation".
3) Yes it was. Before it was bricked I essentially always had it in debug mode because I successfully rooted it and simply left it on debugging mode after having to activate it to root.
4) D801V11B_00.kdz The EXACT same as the original. This is a Videotron (canadian) phone. I can clearly remember without a doubt going into about phone and this is what it was running before all of this happened.
5) I am having a bit of memory strain here, but I do believe it also said adb devices before any of the issues came. It is a good point I will try "adb device" from another trusted computer.
Other notes: I can browse the android os for a few seconds. Sometimes sound does not work, wifi is non functional (even though the keyboard never appears, I managed to have a security free wifi in my proximity and it would not connect (was saying: temporarily avoiding bad signal)) and also I do have modemstat1.img and modemstat2.img backups for EFS.
adb devices consistently shows "offline" but it is definitely recognizing the phone. I have also tried using usb debugging activated and still "offline". Drivers are up to date and all.
The upper drawer in the usual g2 user interface is strange now. it doesnt have anything except for the date (1970 something...) and a "gear" icon for system settings. I am talking the drawer you drag down from the top of the screen.
This phone was working with absolutely no problems 2 days ago.
Thank you so much for looking into this. I have certainly exhausted my repairing capacities. I am entirely dependent upon the knowledgeable individuals in here from here on out.
Click to expand...
Click to collapse
Hmmmm..... why your adb devices is not working? But the re-pair works and you can then do hard reset.
But that is good information you shared.
Maybe someone else can chime in.
From my experience:
1) adb usb access seems spotty. My win 7 64 connected fine and it even kept the shell through the reboot cycle. But on my win 7 32 machine it was only detecting device and then not able to shell.
2) I was also able to use from the LG website LG MOBILE SUPPORT TOOLS.
Download the LG MOBILE SUPPORT TOOL
I downloaded the most recent one from the LG website and make sure to select your options >> country and then the correct phone model at the upper right hand corner of the tool.
Then install USB driver for correct phone model.
Then see if USB works, "adb device" should return the device code.
"adb shell" should show the shell prompt.
3) There is always fastboot. But I an noob and know 0% about how to properly connect and use it.
Some others please chime in and help this droid bro!
I briefly took over another thread where this issue didn't belong, but since I am still having issues, I thought I would start my own thread. Okay, so I am on Sprint, sideloaded several of the updates, including most recently the Oreo Beta. I have been very happy with the beta, and was looking forward to the update due this week. However, yesterday evening I dropped the phone on the sidewalk and it cracked very badly, and as I am paying insurance with Sprint I want to bring it to a store and have it fixed. Not only is the screen badly cracked, but the keyboard is acting up a bit also.
Anyway, I was getting advice on the Oreo thread about how to do this, and as I said, I had hijacked the thread, but I was at work and didn't get to try this until tonight when I got home. Anyway, I had originally plan to just find the Ota and sideload it, but it was recommend that I use flashall and the full image file from the Essential site. I tried to do that, but when I restart the phone to get into Bootloader mode, it disappeared from the list of devices visible on my desktop and via adb. It was a bit disturbing to me as I am not used to working in Bootloader, previously did anything like this via recovery, and I wasn't sure how to exit the bootloader, but I chose power off, and saw a weird screen with what looked like a coffee cup, and eventually the phone rebooted and seems unchanged at the moment.
I still want to revert to the sprint nougat before I bring the phone in, but I admit I am a little nervous now about the best way to do this. I could use some suggestions. I hope this post is not too long-winded, but I wanted to explain as much of what has happened as possible.
maltydog said:
I briefly took over another thread where this issue didn't belong, but since I am still having issues, I thought I would start my own thread. Okay, so I am on Sprint, sideloaded several of the updates, including most recently the Oreo Beta. I have been very happy with the beta, and was looking forward to the update due this week. However, yesterday evening I dropped the phone on the sidewalk and it cracked very badly, and as I am paying insurance with Sprint I want to bring it to a store and have it fixed. Not only is the screen badly cracked, but the keyboard is acting up a bit also.
Anyway, I was getting advice on the Oreo thread about how to do this, and as I said, I had hijacked the thread, but I was at work and didn't get to try this until tonight when I got home. Anyway, I had originally plan to just find the Ota and sideload it, but it was recommend that I use flashall and the full image file from the Essential site. I tried to do that, but when I restart the phone to get into Bootloader mode, it disappeared from the list of devices visible on my desktop and via adb. It was a bit disturbing to me as I am not used to working in Bootloader, previously did anything like this via recovery, and I wasn't sure how to exit the bootloader, but I chose power off, and saw a weird screen with what looked like a coffee cup, and eventually the phone rebooted and seems unchanged at the moment.
I still want to revert to the sprint nougat before I bring the phone in, but I admit I am a little nervous now about the best way to do this. I could use some suggestions. I hope this post is not too long-winded, but I wanted to explain as much of what has happened as possible.
Click to expand...
Click to collapse
Just an FYI, I found that putting Oreo on the phone resulted in ADB not working 100% anymore, such as attempting to reboot into recovery/etc. It would just reboot back into the O.S..
Here is what I did to flash the stock firmware.
- download the current release you want to flash. (e.g. NMJ32F), then unzip it into a new folder.
- on your phone, verify that USB debugging and OEM unlocking are turned on in the developers menu.
- reboot your phone into the fastboot mode (power and volume down buttons)
- from your adb command line: type: fastboot flashing unlock
- This will make your phone show a new screen asking if you want to unlock the bootloader. Use the volume down to select YES, and hit the power button. It will now reboot and erase the phone. It will eventually end up booting up too request you setup the phone. (that is what it did for me.)
- reboot the phone back into the fastboot mode (power and volume down buttons)
- you should now see the bootloader listed as unlocked (vs locked)
- from your adb command line: type: fastboot devices (which should show your phones serial number and fastboot next too it.
- on your computer, using the command line, go to the unzipped folder of the NMJ32F build you downloaded
- in the folder there is a batch file you will run called flashall.bat. run it
- your phone will start flashing the NMJ32F build
- when it completes it will reboot a couple of times, erase the phone, and end up at the "lets get started" screen.
- reboot the phone back to the fastboot mode
- from your adb command line: type: fastboot flashing lock
- select the option to lock your bootloader. The phone will reboot/erase I believe, and then end up back to the "lets get started" screen.
- after you setup your phone, you can go back into the developers menu to turn off the oem unlocking
The above steps pretty much follow essentials instructions. (the essential instructions don't give some specifics.)
You are all done. (I recommend you review my instructions and the essential instructions carefully, don't copy paste commands as I may have spelled something wrong, etc.. Just wanted to give you a flow of the process.)
I was following those directions, but what happens is that though the phone appears as a device in adb before rebooting, once I reboot into fastboot mode, it is no longer listed. I also noticed that when tried to reboot the phone into bootloader mode with an adb command, instead, it did a regular reboot, and when it did that reboot, it again was no longer listed as a device, because it went into charging mode. So I'm not sure how to keep this from happening.
maltydog said:
I was following those directions, but what happens is that though the phone appears as a device in adb before rebooting, once I reboot into fastboot mode, it is no longer listed. I also noticed that when tried to reboot the phone into bootloader mode with an adb command, instead, it did a regular reboot, and when it did that reboot, it again was no longer listed as a device, because it went into charging mode. So I'm not sure how to keep this from happening.
Click to expand...
Click to collapse
The reason why the adb command (to go into bootloader mode) didn't work is it is broken when you installed Oreo, that is why you need to do it manually.
When you put your phone into fastboot mode (power button / volume down) plug in your phone into your computer, and from command prompt (make sure you are in the adb folder), type fastboot devices (don't type adb devices) and see if anything replies back.
kbonnel said:
The reason why the adb command (to go into bootloader mode) didn't work is it is broken when you installed Oreo, that is why you need to do it manually.
When you put your phone into fastboot mode (power button / volume down) plug in your phone into your computer, and from command prompt (make sure you are in the adb folder), type fastboot devices (don't type adb devices) and see if anything replies back.
Click to expand...
Click to collapse
Thanks, I understand now. I can't start this tonight, but I will try the again next time I have time at the desktop.
You are probably missing the phone's driver. Download this, Essential device driver for Windows machines. Supports 32/64 bit on Windows 7, 8 and 10., from the essential developer site and install it.
damn it, I read somewhere that there are problems while using adb on the current official beta. There was a command for getting connection again. But I can't find it right now.
Just to be clear. when the phone is on, you enabled USB debugging and plugged in the USB cable and checked the tickbox before you granted debugging access, right? If you don't check the box, there is no access granted after a phone reboot.
take care, I had problems getting through the initial phone setup after I did a factory reset. The Oreo beta still has some hickups. I got it to work after a few reboots. Without finishing the intial phone setup you can't enable USB debugging, you know.
emowing said:
You are probably missing the phone's driver. Download this, Essential device driver for Windows machines. Supports 32/64 bit on Windows 7, 8 and 10., from the essential developer site and install it.
Click to expand...
Click to collapse
Good point on the driver, I wasn't even thinking about that.
Well, my phone was being read when I previously sideloaded updates, so I think I have the right drivers, but I will double check. Can anyone suggest why the phone keeps defaulting to charging mode rather than file transfer every time I reboot it?
maltydog said:
Well, my phone was being read when I previously sideloaded updates, so I think I have the right drivers, but I will double check. Can anyone suggest why the phone keeps defaulting to charging mode rather than file transfer every time I reboot it?
Click to expand...
Click to collapse
that's a typical android habit. charging mode is default.
did you checked the tickbox when debugging window is appearing?
iceman#1 said:
that's a typical android habit. charging mode is default.
did you checked the tickbox when debugging window is appearing?
Click to expand...
Click to collapse
Yes.
iceman#1 said:
that's a typical android habit. charging mode is default.
did you checked the tickbox when debugging window is appearing?
Click to expand...
Click to collapse
Yes, I did, thanks.
F
iceman#1 said:
that's a typical android habit. charging mode is default.
did you checked the tickbox when debugging window is appearing?
Click to expand...
Click to collapse
Yes, I did, thanks. Trying to reply and it doesn't appear. Edit: Sorry for the multiple posts,they all appeared at once.
Okay, I am back to this now, I had time today. I installed the windows drivers from the Essential site (I am running Windows 10 64 bit) and the device was recognized in fastboot devices. The phone wiped my data and restarted with a setup screen. So far, so good. So I shut down the phone again, turned it on again in fastboot mode, it was unlocked. I went into a CMD screen and typed fastboot devices, and the phone was still listed there. So I opened windows explorer and got to the folder where I had unpacked the image files and also copied the flashboot file. I right-clicked the flashall.bat file, chose run as administrator. When I did this, I got a bunch of error messages that went by so fast, they were practically impossible to read, though they seem to say something about files not found. I didn't see any log file in the folder, so I guess they are not created. I went back to the Essential site and downloaded the zip file with the correct image files again and tried a second time, with the same results. Anyway I have wiped my phone, but still have not reinstalled the Sprint nougat software I need on this phone. Any other suggestions?
Okay, I tried again, and I was able to read the error message. They all said cannot load "filename" no such file or directory. It sounds like some kind of path error, right? I expanded the file from the Essential download for build Build NMI81C into their own directory, a subdirectory of a library where I have been keeping various android files, and I copied the flashboot file into the same directory from the platform-tools download, but only that file. That seems to be what instructions specify.
Also, I notice on this thread https://forum.xda-developers.com/essential-phone/development/stock-7-1-1-nmj20d-t3701681/page3 it mentions also using the command "fastboot flashing unlock_critical" but I do not see that elsewhere.
I was able to get flashall to run using the command prompt instead of Windows Explorer. It seemed to run okay, except a couple of items cause me some concern.
I got a message "FAILED (remote: Flashing is not allowed for Critical Partitions)" for the abl.img file.
And the other command "Did you mean to fashboot format this ext4 partition".
Are either of these a problem?
Try running the commands one at a time. Open the flash-all.sh in a text editor and copy the commands.
As I said in my last message, I was able to get Flashall to work when I ran it in the CMD prompt rather than in windows explorer (which is how it was done in the video posted on Youtube, but didn't work for me). My only concern at this point is whether I should be concerned about the two commands posted in the email.
Interestingly enough, my phone did an update to the build NMJ32F as soon as I started it up.
maltydog said:
As I said in my last message, I was able to get Flashall to work when I ran it in the CMD prompt rather than in windows explorer (which is how it was done in the video posted on Youtube, but didn't work for me). My only concern at this point is whether I should be concerned about the two commands posted in the email.
Interestingly enough, my phone did an update to the build NMJ32F as soon as I started it up.
Click to expand...
Click to collapse
Did u not do the flashing unlock_critical?
Airwolf79 said:
Did u not do the flashing unlock_critical?
Click to expand...
Click to collapse
No I didn't. It was not mentioned by anyone but me in this thread until you did.
So far I have received no error messages since I did the reversion to stock. As I said,
I did get an update almost immediately.