A bit of an SOS situation if anyone knows the right steps please
Well, I restored a Titanium Backup and mistakenly toggled the "restore system apk". It ran fine, all restored and then when I rebooted got stuck.
By "stuck", it re-boots constantly. It shows the LG animation, then all I can see is two messages before it starts booting again:
1) "Unfortunately, Google Play Services Has Stopped"
2) "Unfortunately, System UI has stopped
... and then it does the entire boot sequence, animation, again, and again.
Here is what I can do:
* It is in USB debug mode.
* I have drivers on laptop
* I am able to connect with adb and also shell into phone.
* With adb, I have output to the file an "adb bugreport" as well as an "adb logcat".
* I have several backups:
a) The modemsst1.img and modemsst2.img created by Titanium Backup
b) Titanium backups (full apps and data)
c) an "adb backup - all" backup
* I managed to get it into firmware update mode by pressing the volume up button and the power button and then when it flashed red a few times, just the up button. So, I can get it into Firmware update mode.
Of course, I have never really used adb before, except to dabble a bit. So, I am encouraged that I can somehow get into with shell.
I am not unplugging it until I know what to do!
Since then I have been able to turn the phone off and also put it into charging on USB.
This is what worked:
* Hold down power and volume down button until booting stops and phone turns off completely.
When it does shut down, I kept buttons down until it flashes logo again and then shuts down again. Then I let go. Phone is off and when I plugged in the charger it shows charging animation.
Now, after inspecting the bugreport, I noticed a lot of these messages for all the system apps like this one:
"I/PackageManager(21318): Expecting better updatd system app for com.lge.sizech"
I think the cause of all this shralp is this, I did a LG Mobile Support Tool "Upgrade Recovery" and then in Titanium Backup I restored an older backup (incl system apks). At least that makes sense seeing all the "Expecting better apdat system app" messages in the bugreport.
Still not sure what to do next
I tried the very good instructions here:
[Guide] Unroot/Unbrick - flash official factory firmware with LG Launche
http://forum.xda-developers.com/showthread.php?t=2471370
The update succeeded. However, when I rebooted the phone it is in the same boot-loop with message that it was before.
I used the BELL D803B10D_00.kdz file. Now I will try with the earlier version BELL D803BA_00.kdz file.
We will see what happens ...
do you have nandroid backup from previous rom?
I have three backups:
1) Titanium Backup (full)
* This was my first backup performed right after rooting device and installing Titanium Backup.
2) Titanium Backup (full)
* Did this 2 days ago. Device was working OK and did as precaution.
3) ADB BACKUP. I did this one before my Titanium restore.
I restored the first titanium backup and that (ooooppps!) was after I did an LG Firmware update.
ALSO:
I am on Windows 7 64 and although adb works fine, fastboot does not. I understand that might be a problem with windows 7 64.
So, unless anyone objects, I am going to redo on my windows 32 machine and also "fastbook oem unlock".
Since firmware is OK, if I do the fastboot oem unlock, that will wipe everything. But I can still boot and re-setip the phone, right?
Just checking before I fudge everything up here ..
ALSO ALSO:
I had antivirus/theft security installed and I disabled it partway through last restore.
Maybe that has somethng to do with this all .
But I am still cool because I can ADB and also firmware install seems ok.
ADB works and that is the one good sign.
or you can follow ADB Sideload method
http://forum.xda-developers.com/showthread.php?t=2318497
zekurosu said:
or you can follow ADB Sideload method
http://forum.xda-developers.com/showthread.php?t=2318497
Click to expand...
Click to collapse
I don't (didn't) have TWRP installed. How can I sideload without it?
Also, should I adb oem unlock to get it wiped at this point?
I'm having a similar problem on a Bell D803. Just happened very randomly today. I turned my phone off for an exam, then turned it back on after.. initially had no signal and a black background. Settings for factory reset wouldn't work. My phone is rooted and has TWRP. I went into recovery and formatted.
Bootloop.
Bootloop.
Bootloop x 20.
I however, don't get the same two messages. I just keep bootlooping.
Got home, tried to go through download mode to unbrick it, but for some reason my computer isn't picking it up. I have all the drivers, and before this incident, it was recognized.
Any solutions?
I'm thinking of buying an OTG USB and then just flashing a stock zip from recovery. Would that be a possible viable solution?
asdfvtn said:
I'm having a similar problem on a Bell D803. Just happened very randomly today. I turned my phone off for an exam, then turned it back on after.. initially had no signal and a black background. Settings for factory reset wouldn't work. My phone is rooted and has TWRP. I went into recovery and formatted.
Bootloop.
Bootloop.
Bootloop x 20.
I however, don't get the same two messages. I just keep bootlooping.
Got home, tried to go through download mode to unbrick it, but for some reason my computer isn't picking it up. I have all the drivers, and before this incident, it was recognized.
Any solutions?
I'm thinking of buying an OTG USB and then just flashing a stock zip from recovery. Would that be a possible viable solution?
Click to expand...
Click to collapse
Well, I am able to connect with adb fine on my laptop (Win 7 64) but not on my desktop (Win 7 32)
But on my Win 7 64 I cannot get into fastboot.
I am wondering if the driver install on my desktop went foo-bar and needs reinstall. Also, I noticed that the website drivers are more recent USB drivers than some of the ones linked on this site.
I used adb uninstall package for many user packages and it was success. But I still see the packages listed in the bugreport?
For example: I already uninstalled "com.benhirashima.skiplock" and also "com.lookout".
Why? What to do to really zap them for good?
Sorry, I posted the wrong link earlier.
This was the guide I used which succeeded but made no difference to the boot-loop.
LG G2 Stock Firmware (Go Back to Stock)
http://forum.xda-developers.com/showthread.php?t=2432476&highlight=d803
Just figured out how to do a factory reset.
http://www.youtube.com/watch?v=3ogBvzbPikc
The hard reset worked and now I am configuring the phone settings!
So, again, this is what I did:
1) http://forum.xda-developers.com/showthread.php?p=45293512
2) http://www.youtube.com/watch?v=3ogBvzbPikc
Not sure if it all worked but I am setting the phone up as we speak (or as I type)
natureburger said:
Well, I am able to connect with adb fine on my laptop (Win 7 64) but not on my desktop (Win 7 32)
But on my Win 7 64 I cannot get into fastboot.
I am wondering if the driver install on my desktop went foo-bar and needs reinstall. Also, I noticed that the website drivers are more recent USB drivers than some of the ones linked on this site.
Click to expand...
Click to collapse
Hmm that's strange. Unfortunately for me, I'm already on 64-bit and it still isn't picking it up.
ALL FIXED UP
WORKING 110%
:good:
natureburger said:
ALL FIXED UP
WORKING 110%
:good:
Click to expand...
Click to collapse
I have followed this to a t.
Succesfully flashed the stock firmware that came with the phone when sold.
Did hard reset using the the power button and volume down
= phone rebooting every 10 seconds, no wifi, imei = null
adb devices = offline.
Really depressed right now. If anybody can help me I would appreciate it.
zprovo said:
I have followed this to a t.
Succesfully flashed the stock firmware that came with the phone when sold.
Did hard reset using the the power button and volume down
= phone rebooting every 10 seconds, no wifi, imei = null
adb devices = offline.
Really depressed right now. If anybody can help me I would appreciate it.
Click to expand...
Click to collapse
Press the power button down and hold it.
It should turn off, then look like it is turning on, (flash logo very briefly) and then turn off.
Let go of power button and it should stay off.
Do that. Now, does it work to turn off completely?
Let's see if you can do that first.
Then .. do hard reset, exactly like this:
http://www.youtube.com/watch?v=3ogBvzbPikc
Does the hard reset screen show and give you hard reset options?
natureburger said:
Press the power button down and hold it.
It should turn off, then look like it is turning on, (flash logo very briefly) and then turn off.
Let go of power button and it should stay off.
Do that. Now, does it work to turn off completely?
Let's see if you can do that first.
Click to expand...
Click to collapse
Yup. I totally understand what you are saying and have done it many times. I had to use that method to get into download mode and also had to use it to do hard reset.
I just reflashed the phone all over again a second time succesfully.
Reboots every 5 seconds. Keyboard came up for a few seconds for the first time in 48 hours during the initial setup phase. 5 seconds later as I was trying to input a wifi code it would not appear. then it rebooted as usual.
I really appreciate any input right now. :cyclops::crying:
zprovo said:
Yup. I totally understand what you are saying and have done it many times. I had to use that method to get into download mode and also had to use it to do hard reset.
I just reflashed the phone all over again a second time succesfully.
Reboots every 5 seconds. Keyboard came up for a few seconds for the first time in 48 hours during the initial setup phase. 5 seconds later as I was trying to input a wifi code it would not appear. then it rebooted as usual.
I really appreciate any input right now. :cyclops::crying:
Click to expand...
Click to collapse
1) Are you able to completely turn it off using my instructions?
2) When you hard reset (2nd half of this video), http://www.youtube.com/watch?v=3ogBvzbPikc
a) Does the hard reset screen show?
b) Does it give you the hard reset options?
3) Before it was bricked, was it in 'usb debug mode' in developer options?
4) Which kpz version did you restore to?
5) Did your "adb devices" ever work? Did your "adb shell" ever work?
natureburger said:
1) Are you able to completely turn it off using my instructions?
2) When you hard reset (2nd half of this video), http://www.youtube.com/watch?v=3ogBvzbPikc
a) Does the hard reset screen show?
b) Does it give you the hard reset options?
3) Before it was bricked, was it in 'usb debug mode' in developer options?
Click to expand...
Click to collapse
1) Yes absolutely. It is sitting next to me right now doing nothing at all because I turn it off when I am not trying to fix it, otherwise it keeps rebooting relentlessly.
2) a) Yes, same as the video. b) Yes it says the same exact thing as the video. I press power key twice and it begins. The stock recovery android appears with a loading bar on the bottom for ~1 minute then it goes to the boot "lg animation".
3) Yes it was. Before it was bricked I essentially always had it in debug mode because I successfully rooted it and simply left it on debugging mode after having to activate it to root.
4) D801V11B_00.kdz The EXACT same as the original. This is a Videotron (canadian) phone. I can clearly remember without a doubt going into about phone and this is what it was running before all of this happened.
5) I am having a bit of memory strain here, but I do believe it also said adb devices before any of the issues came. It is a good point I will try "adb device" from another trusted computer.
Other notes: I can browse the android os for a few seconds. Sometimes sound does not work, wifi is non functional (even though the keyboard never appears, I managed to have a security free wifi in my proximity and it would not connect (was saying: temporarily avoiding bad signal)) and also I do have modemstat1.img and modemstat2.img backups for EFS.
adb devices consistently shows "offline" but it is definitely recognizing the phone. I have also tried using usb debugging activated and still "offline". Drivers are up to date and all.
The upper drawer in the usual g2 user interface is strange now. it doesnt have anything except for the date (1970 something...) and a "gear" icon for system settings. I am talking the drawer you drag down from the top of the screen.
This phone was working with absolutely no problems 2 days ago.
Thank you so much for looking into this. I have certainly exhausted my repairing capacities. I am entirely dependent upon the knowledgeable individuals in here from here on out.
zprovo said:
1) Yes absolutely. It is sitting next to me right now doing nothing at all because I turn it off when I am not trying to fix it, otherwise it keeps rebooting relentlessly.
2) a) Yes, same as the video. b) Yes it says the same exact thing as the video. I press power key twice and it begins. The stock recovery android appears with a loading bar on the bottom for ~1 minute then it goes to the boot "lg animation".
3) Yes it was. Before it was bricked I essentially always had it in debug mode because I successfully rooted it and simply left it on debugging mode after having to activate it to root.
4) D801V11B_00.kdz The EXACT same as the original. This is a Videotron (canadian) phone. I can clearly remember without a doubt going into about phone and this is what it was running before all of this happened.
5) I am having a bit of memory strain here, but I do believe it also said adb devices before any of the issues came. It is a good point I will try "adb device" from another trusted computer.
Other notes: I can browse the android os for a few seconds. Sometimes sound does not work, wifi is non functional (even though the keyboard never appears, I managed to have a security free wifi in my proximity and it would not connect (was saying: temporarily avoiding bad signal)) and also I do have modemstat1.img and modemstat2.img backups for EFS.
adb devices consistently shows "offline" but it is definitely recognizing the phone. I have also tried using usb debugging activated and still "offline". Drivers are up to date and all.
The upper drawer in the usual g2 user interface is strange now. it doesnt have anything except for the date (1970 something...) and a "gear" icon for system settings. I am talking the drawer you drag down from the top of the screen.
This phone was working with absolutely no problems 2 days ago.
Thank you so much for looking into this. I have certainly exhausted my repairing capacities. I am entirely dependent upon the knowledgeable individuals in here from here on out.
Click to expand...
Click to collapse
Hmmmm..... why your adb devices is not working? But the re-pair works and you can then do hard reset.
But that is good information you shared.
Maybe someone else can chime in.
From my experience:
1) adb usb access seems spotty. My win 7 64 connected fine and it even kept the shell through the reboot cycle. But on my win 7 32 machine it was only detecting device and then not able to shell.
2) I was also able to use from the LG website LG MOBILE SUPPORT TOOLS.
Download the LG MOBILE SUPPORT TOOL
I downloaded the most recent one from the LG website and make sure to select your options >> country and then the correct phone model at the upper right hand corner of the tool.
Then install USB driver for correct phone model.
Then see if USB works, "adb device" should return the device code.
"adb shell" should show the shell prompt.
3) There is always fastboot. But I an noob and know 0% about how to properly connect and use it.
Some others please chime in and help this droid bro!
Related
Well to make it simple, the newest twrp is very buggy and to make a long story short i installed a new rom, and while it was restoring my data, my n7 shut off. its done this before so naturaly i held the power+volume down buttons too boot into the bootloader but it wont turn on. Any help/ suggestions?
Put it on the power supply and let it there for some time ... Then start again.
Sent from my Nexus 7 using xda app-developers app
AndDiSa said:
Put it on the power supply and let it there for some time ... Then start again.
Sent from my Nexus 7 using xda app-developers app
Click to expand...
Click to collapse
Thank you ill try that. it was at 33% battery when this happened though
Um... It probably didn't shutoff. There's a screen timeout.
Sent from my Nexus 7 using Tapatalk HD
korockinout13 said:
Um... It probably didn't shutoff. There's a screen timeout.
Sent from my Nexus 7 using Tapatalk HD
Click to expand...
Click to collapse
i know about the screen time out, i tapped the screen for it to rewake and it didnt work, then i tried pressing the sleep button once for it to unlock and that didnt work. so it indeed shutoff
frap129 said:
Well to make it simple, the newest twrp is very buggy and to make a long story short i installed a new rom, and while it was restoring my data, my n7 shut off. its done this before so naturaly i held the power+volume down buttons too boot into the bootloader but it wont turn on. Any help/ suggestions?
Click to expand...
Click to collapse
I'm confused. It's a little off-topic, but what does "restoring my data" have to do with TWRP in the context of flashing a new ROM?
Anyway, I would proceed with a dead battery or loose battery connector hypothesis first. It's not obvious why writes to /boot, /cache, /data, or /system would affect the bootloader.
Anything is possible at a low enough probability I suppose, but you should start troubleshooting operations with the high-probability scenarios first.
For instance - with the power off, will the "charging screen" display when you plug the tab in? How about APX** mode? (Plug in to PC and start with Power+Vol-up). If you didn't see either of those, it's likely a power supply or hardware problem.
good luck
** make sure you exit APX mode by holding down the power button for at least 20 seconds. I'm not sure if it shuts itself down after an inactivity timeout - you don't want to be draining power while trying to charge the tab.
bftb0 said:
I'm confused. It's a little off-topic, but what does "restoring my data" have to do with TWRP in the context of flashing a new ROM?
Click to expand...
Click to collapse
Well, you backup your data, Wipe data and cache, flash the rom, gapps, ect. then restore data, the charging screen wont dispaly, apx mode doesnt work, but the whole story: went to flash a newer version of my rom, install faills due to error in updater binary so i go to reboot and it says "No OS Installed! Are you sure you want to reboot?" i press dont reboot, go to install the older version of the rom, go to restore data and then it shut off.
frap129 said:
Well, you backup your data, Wipe data and cache, flash the rom, gapps, ect. then restore data, the charging screen wont dispaly, apx mode doesnt work, but the whole story: went to flash a newer version of my rom, install faills due to error in updater binary so i go to reboot and it says "No OS Installed! Are you sure you want to reboot?" i press dont reboot, go to install the older version of the rom, go to restore data and then it shut off.
Click to expand...
Click to collapse
The lack of APX mode or the charger screen suggests a battery problem or a hardware failure, not a software problem. APX mode will be present even if the tablet has absolutely nothing in flash memory.
Having nothing in /system (no OS or even no filesystem) will not affect bootability of either the bootloader or the recovery.
I don't know why you would wipe data only to restore it after flashing a ROM. Usually wiping cache & dalvik-cache is sufficient for "dirty-flashing" a ROM upgrade as it is very unusual for ROM installs to diddle with the /data partition. (But making full backups is always a good idea.)
I would check (carefully) to see if the battery connector came loose before you decide to throw the tablet away.
good luck
bftb0 said:
The lack of APX mode or the charger screen suggests a battery problem or a hardware failure, not a software problem. APX mode will be present even if the tablet has absolutely nothing in flash memory.
Having nothing in /system (no OS or even no filesystem) will not affect bootability of either the bootloader or the recovery.
I don't know why you would wipe data only to restore it after flashing a ROM. Usually wiping cache & dalvik-cache is sufficient for "dirty-flashing" a ROM upgrade as it is very unusual for ROM installs to diddle with the /data partition. (But making full backups is always a good idea.)
I would check (carefully) to see if the battery connector came loose before you decide to throw the tablet away.
good luck
Click to expand...
Click to collapse
Battery connector didnt come loose, still dosent work. guess it might just be broken
EDIT: I plugged it in to my pc and the google screen came up for about 20 sec then it shut back off. havent been able to get anything since
frap129 said:
Battery connector didnt come loose, still dosent work. guess it might just be broken
EDIT: I plugged it in to my pc and the google screen came up for about 20 sec then it shut back off. havent been able to get anything since
Click to expand...
Click to collapse
Is it possible to enter Odin on the n7?
Sent from my Galaxy Nexus using xda premium
Soldier 2.0 said:
Is it possible to enter Odin on the n7?
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
Odin is Samsung only
Sent from my Galaxy Nexus
You can hold the power button for 10 seconds and wait till you see the Google logo. Then release and hold it 10 seconds again, when the screen turns off hold the volume down button and wait for it till it automatically boots again. You'll enter bootloader mode. Download wugfresh' nexus root toolkit and install it. When the program is loaded there is a flash stock option on the right side of the program. Select the soft brick / boot loop option under the flash button. While in boot loader mode connect your nexus and press the flash button.
This is all I know!
Sent from my Nexus 7 using xda premium
NEXUS 7 Bricked - NO OS - tried everything but...
It's a catch 22 here. I can't get drivers installed and the nexus recognized and so when it comes to flashing/restoring via cmd prompt the PC won't recognize my device and so I can go only get so far. I have no OS installed as I wiped all like an idiot in twrp so how the hell can I get drivers installed on a nexus that has no OS installed? I can't enable usb debugging etc because, well, I have no way of getting the nexus to work so can't get into the settings to do so.
I have tried everything in twrp but there is nothing to restore - i can't get roms pushed onto it - God I give up. All I need is the PC to recognize my device and I know I can crack this. What do I have to do? Please help this idiot.
CarlKirshner1989 said:
It's a catch 22 here. I can't get drivers installed and the nexus recognized and so when it comes to flashing/restoring via cmd prompt the PC won't recognize my device and so I can go only get so far. I have no OS installed as I wiped all like an idiot in twrp so how the hell can I get drivers installed on a nexus that has no OS installed? I can't enable usb debugging etc because, well, I have no way of getting the nexus to work so can't get into the settings to do so.
I have tried everything in twrp but there is nothing to restore - i can't get roms pushed onto it - God I give up. All I need is the PC to recognize my device and I know I can crack this. What do I have to do? Please help this idiot.
Click to expand...
Click to collapse
USB debugging doesn't mean **** when you are in a custom recovery. It has adb already. Your problem is your computer. Fix your computer by following one of the bajillion threads and posts about the nexus 7 drivers issues.
Installing drivers does not need android to be booted.
Your best bet is to put it in fast boot mode and follow Google's own instructions to flash it back to stock.
Sent from my Galaxy Nexus
CarlKirshner1989 said:
It's a catch 22 here. I can't get drivers installed and the nexus recognized and so when it comes to flashing/restoring via cmd prompt the PC won't recognize my device and so I can go only get so far. I have no OS installed as I wiped all like an idiot in twrp so how the hell can I get drivers installed on a nexus that has no OS installed? I can't enable usb debugging etc because, well, I have no way of getting the nexus to work so can't get into the settings to do so.
I have tried everything in twrp but there is nothing to restore - i can't get roms pushed onto it - God I give up. All I need is the PC to recognize my device and I know I can crack this. What do I have to do? Please help this idiot.
Click to expand...
Click to collapse
I must admit I'm a little 'hazy' myself when it comes to ADB related issues... I've never had much cause to use ADB. (Think I've used 'adb pull' on a couple of occasions). And I've never been in the invidious position of not having a bootable Android OS on my Nexus 7 either - which does seems to happen a quite lot with TWRP users, less so with CWM users.
Anyway... just had a tinker... and you could try the following workaround... this seemed to work to for me.
----------------------
Locate the folder on your PC where you keep your FASTBOOT and ADB .exe files...
Copy whatever ROM .zip you want into this folder.
The following example uses SmoothROM-v5.0.zip ... There is nothing to stop you from renaming this to something shorter, for ease of typing later... so, in my case, just smooth.zip.
Boot your Nexus 7 into the BOOTLOADER (Vol down [hold] + Power button), and then into RECOVERY (TWRP) and hook it up your PC.
Open a command prompt window on the aforementioned folder... and type...
Code:
adb devices
...which should yield something like the following...
Code:
List of devices attached
012345679ABCDEF recovery
(If you don't see a serial number... then you definitely have a driver problem...)
Otherwise, it's just...
Code:
adb push smooth.zip /sdcard
Or whatever ROM you wish to 'push' to the emulated SD card.
This will likely take a fair few minutes for a 300Mb+ size file (typically the size of your average ROM)... on my Windows XP box it took 4 minutes (1328 KB/s, 32565894 bytes in 239.486s) to copy over. And there are no 'progress gauges' of any kind, either... So season your patience a liitle. You can always pull up another command prompt window and type adb devices again to ensure you still have an ongoing ADB connection.
Once copied over, and still in TWRP, you can just flash it.
Good luck.
Rgrds,
Ged.
Still nothing on mine. im just about to give up and wait to see if google releases the N7 second generation at the i/o
If You familiar with Linux, You can try to understand the logic of
changing the modes.
You need to run udevadm monitor in one terminal. Then press some
combinations of key/s and look for changes with usb-devices.
The better, if You run wireshark and sniff USB interface with your device.
Put attachment here, with a comments what was pressed.
since it seems to be a hardware problem, not software, im just going to send it to asus and see what they can do.
Hey guys, looking for some assistance here as I am at a complete loss.
Decided tonight to root my 4.2.2 Nexus 10 using the Nexus Rootkit v1.6.3 and the aid of a YouTube video. All went swimmingly up until the TWRP wipe. The video I followed failed the wipe attempt and the guy showed how to get the N10 out of the bootloop and do a 'wipe data/factory reset' via Recovery Mode in the Bootloader and then restart.
Problem is, my wipe never failed like his did in the video (great I thought!) and so I restarted after that and now I find my N10 booting up to the Google Logo (with the padlock at the bottom) and it just sits there. Doesn't even get to the 'X' logo which should come after.
I've tried a few things including the manual wipe data/factory reset from the bootloader and restart but everytime it gets stuck at the Google Logo. I am also now at the point where my N10 doesn't show in Device Manager as it did before. It now shows under 'Portable Devices' as a 'MTP USB Device'.
I am really at a loss here and searching various solutions is just confusing me even more and would appreciate it if someone could help me out, even just getting back to stock for now. That's if it isn't goosed?
Thanks in advance
Have you tried using a different usb port on the PC, and rebooting the PC?
bigmatty said:
Have you tried using a different usb port on the PC, and rebooting the PC?
Click to expand...
Click to collapse
I have yeah. Left my PC off overnight and went back to it again this morning and same issue.
Plug it into the PC (this time using a USB port on the back) and it initially comes up 'installing device driver software' quickly followed by 'device driver software was not installed successfully', quickly followed by 'installing device driver software' again and that's when it shows up in Device Manager as 'MTP USB Device' under Portable Devices, whereas before during the root attempt it was show as 'Nexus 10'.
When I first read the subject line I thought it was "another one of these" where OP hadn't searched on the existing boards. But when I read OP I see you did try "the usual suggestions". Hoping a more seasoned pro jumps in here to help...
I can say that on the handful of "really bad" posts like this that I've seen they usually end with the person saying something like "well I don't know what happened I just kept trying all the power button / charge recommendations and finally it worked" - so don't underestimate the effectiveness of repeatedly trying it like a mad man!
Some random suggestions I have that may help:
-Can you leave it on, on the Google screen, to where the battery 100% drains, maybe this could act as a "battery pull"
-Try a different USB cord
-Try rebooting it via the power buttons while the device is plugged into the wall charger
-Download the Android SDK, then use its "update manager" to update its USB drivers to today's definitions
-Try another PC
Good luck!
Thanks for the suggestions bigmatty, I'll certainly give them a go when I get in later.
I think my biggest concern is that there doesn't seem to be any OS on it, possibly to do with the wipe during TWRP and then I rebooted - was I supposed to reboot at that stage? That's where I got into this loop. And now it doesn't detect it as 'Nexus 10' in my Device Manager on my main PC. Only this MTP USB Device - sometimes showing a conflict warning triangle, sometimes not and no longer showing as a storage device in My Computer.
I did connect it to my Netbook (Running XP) earlier and it detected it as an 'Android Device' under Other Devices in Device Manager. Tried installing it with the naked drivers on the Android SDK and it now lists it under 'Android Device' in my Netbook's Device Manager as a 'ADB Device' (I think, would need to double check as I'm not on it at the moment.)
I just want to find some way of getting it back to factory settings and stock OS if possible and then take it from there again. Don't fancy at £319 paperweight! I'm usually alright with these things too.
Thanks again (And if anybody else has any other input in the meantime I would be grateful - I'll try anything at this stage!)
I'd say its a good thing that the PC exhibits varying behavior - because that means there is still hope!
It really boils down to if you can open an adb.exe shell to the device. Can you? It would not be when its showing as MTP but it would be when its showing as adb in Device Manager. If you can then here is a thread where I explain (pretty good, I think) how to get back to stock:
http://forum.xda-developers.com/showthread.php?t=2185123
Now I realize Im not clear on a second avenue - can you still get into TWRP?
~bm
bigmatty said:
Now I realize Im not clear on a second avenue - can you still get into TWRP?
~bm
Click to expand...
Click to collapse
Can't really get into much on the Tablet itself. It boots up, gets to the Google logo (with the padlock symbol at the bottom suggest it has been partially rooted (?)). I can get into the Bootloader by holding down the Power + 2 vol buttons. Once in the Bootloader I have the options of Start/Power Off/Recovery Mode/Restart Bootloader.
When I go into Recovery Mode I can get access to the blue menu where I get the options to restart/something about adb/wipe data/factory reset/delete cache partition (paraphrasing here).
Don't know how many times I've tried the wipe data/factory reset option and reboot but always get sent back to the same loop.
I'll give you're other idea a shot as well later. Thanks again.
bigmatty said:
I'd say its a good thing that the PC exhibits varying behavior - because that means there is still hope!
It really boils down to if you can open an adb.exe shell to the device. Can you? It would not be when its showing as MTP but it would be when its showing as adb in Device Manager. If you can then here is a thread where I explain (pretty good, I think) how to get back to stock:
http://forum.xda-developers.com/showthread.php?t=2185123
Now I realize Im not clear on a second avenue - can you still get into TWRP?
~bm
Click to expand...
Click to collapse
bigmatty, you the man!
Managed to get back to factory stock following yours and styckx's guidelines. Couple of little teething problems along the way but nothing I couldn't get around.
I now have a fully functioning Tablet again and I thank you for it.
Might give the Rooting a miss for now but if I come back around to the idea I'll be sure to follow the guides on here this time instead.
Thanks a bunch again for taking your time out to reply to my thread and get me back up and running again. :good:
Scotman57 said:
bigmatty, you the man!
Managed to get back to factory stock following yours and styckx's guidelines. Couple of little teething problems along the way but nothing I couldn't get around.
I now have a fully functioning Tablet again and I thank you for it.
Might give the Rooting a miss for now but if I come back around to the idea I'll be sure to follow the guides on here this time instead.
Thanks a bunch again for taking your time out to reply to my thread and get me back up and running again. :good:
Click to expand...
Click to collapse
Awesome! Glad it worked out
I went to update to KitKat and it was nearly done and then the "No Command" error came up. My tablet has an unlocked boot loader but isn't rooted. However it was before but I updated it from an OTA and that got rid of it. I've tried booting into recovery etc but the same thing happens.
Anyone have any advice please?
Same exact issue and set up here. Also, maybe I'm just dumb, but I can't get my tablet to turn off either. It just keeps cycling back to the "no command" screen until I do something.
tgearhar said:
Same exact issue and set up here. Also, maybe I'm just dumb, but I can't get my tablet to turn off either. It just keeps cycling back to the "no command" screen until I do something.
Click to expand...
Click to collapse
I think that both of you what you see (the "no command") is your stock recovery, if indeed you see an android with a yellow !.
If it is the case to access the menu of the stock recovery press power and tap volume up. The menu will give you the choice of rebooting your Nexus 7.
gunner1937 said:
I think that both of you what you see (the "no command") is your stock recovery, if indeed you see an android with a yellow !.
If it is the case to access the menu of the stock recovery press power and tap volume up. The menu will give you the choice of rebooting your Nexus 7.
Click to expand...
Click to collapse
I can get to the menu but when trying the reboot option, it just cycles the same way again. Back to the android with a red ! and says "No command." I also tried clearing cache and data to no avail. I was going to try using ADB to manually push the update but my computer was recently updated and now I can't get the driver installed for some reason.
I spent too much time messing around with and learning how to do things with my SIII and not enough time with this
Same deal here! Not sure what to do short of wiping and losing my info.
Same here...any advice? Not sure what happened. OTA update too.
Significa said:
Same here...any advice? Not sure what happened. OTA update too.
Click to expand...
Click to collapse
Wow, this seems to be widespread, at least somewhat. I'm in same situation. Toolkits, adb, nothing works. I thought this was a soft brick, but now I'm thinking it's toast. Probably doesn't help that I didn't have Dev options enabled along with USB Debugging. I can't even turn it off. Just bootloops after Google logo shows up twice, then to No Command error, then starts over again. I wonder what the hell is causing this. (Device was locked and unrooted)
Same boat here, even sideloaded the factory image via ADB.
[QUOTE [/QUOTE]
I was going to try using ADB to manually push the update but my computer was recently updated and now I can't get the driver installed for some reason.
If you have android-sdk-windows installed on your computer do not forget to update it through "SDK Manager.exe".
Pushing via ADB didn't work for me. That also failed.
I caved and called Google. Tech support is stumped as well.
Sent from my Nexus 5 using Tapatalk
Could this be a widespread issue? Like I don't even understand why it happened at all!
Sent from my Nexus 5 using XDA Premium 4 mobile app
I finally got mine working again!
I tried a million different things so I'm going to try and explain my process as simple as I can, I apologize in advance because I am far from an expert...
First, I tried using the method, well some of it, from this thread: http://forum.xda-developers.com/showthread.php?t=1907796
- I would suggest using this thread to get everything set up (drivers, ADB, the factory image downloaded and in the correct file location) I wasn't able to get the drivers working correctly with that route so I ended up using the toolkit to get them working but that thread helped me get all of the system files in the correct location and helped get all of the ADB stuff set up.
Once you have everything set up and your computer recognizes the tablet, (I checked that by opening a cmd prompt and using the command from the original thread above "adb devices"). As long as you see your device, I think you should be good.
From the "No Command" screen I held down Power and Volume + to get the menu to come up. I then chose the Restart option and immediately held Power and Volume -. This got me into the Fastboot Mode.
Once in Fastboot mode I went to the cmd prompt on my computer and used the following commands in this order from this post:
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot erase system -w
fastboot flash system system.img
fastboot reboot
*Make sure that all of the image files are in the proper location on your computer otherwise this step is worthless
The tablet then rebooted normally and I was able to set everything up again. Again, I am by no means an expert at all, this is just what worked for me. Try at your own risk.
I hope I covered all of the steps, I tried a million different things last night so they all kind of run together.
I ended up doing and it worked for me as well. Wiped everything though. How can I restore / reinstall my apps w/o needing to download them all again?
Two things: That guide says you must have USB Debugging enabled. Since my wife had this tablet, I did not have dev options enabled at all, including USB debug.
The other thing is that when I run the SDK Manager, nothing happens on my computer. I double click it or try Run as Admin, and a small CMD box flashes on my screen for a millesecond and disappears. That's all.
My wife's 2012 N7 is having this same problem. Unlocked bootloader, but I reflashed factory image and unrooted before giving it to her. She got the OTA last night, and now stuck at No Command.
I've subscribed to this thread, hoping that you guys will have it solved before I get home from work tonight! Would love to not have her lose all her data.
(I was kinda mad that she got the OTA last night and I haven't got it yet on my 2013 N7, but that's another gripe for another thread)
killswitch11 said:
Two things: That guide says you must have USB Debugging enabled. Since my wife had this tablet, I did not have dev options enabled at all, including USB debug.
The other thing is that when I run the SDK Manager, nothing happens on my computer. I double click it or try Run as Admin, and a small CMD box flashes on my screen for a millesecond and disappears. That's all.
Click to expand...
Click to collapse
Unfortunately I'm not sure on the SDK manager part. As far as the USB Debugging, I'm 98% sure that I did not have it enabled either. I think I did at one point but after doing several OTA upgrades, I'm sure it got unchecked.
---------- Post added at 01:34 PM ---------- Previous post was at 01:01 PM ----------
kr33mo said:
I ended up doing and it worked for me as well. Wiped everything though. How can I restore / reinstall my apps w/o needing to download them all again?
Click to expand...
Click to collapse
I don't believe there is a way. Maybe someone smarter than myself can chime in but I had to let the play store do it's thing and re-download all of mine.
tgearhar said:
I finally got mine working again!
I tried a million different things so I'm going to try and explain my process as simple as I can, I apologize in advance because I am far from an expert...
First, I tried using the method, well some of it, from this thread: http://forum.xda-developers.com/showthread.php?t=1907796
- I would suggest using this thread to get everything set up (drivers, ADB, the factory image downloaded and in the correct file location) I wasn't able to get the drivers working correctly with that route so I ended up using the toolkit to get them working but that thread helped me get all of the system files in the correct location and helped get all of the ADB stuff set up.
Once you have everything set up and your computer recognizes the tablet, (I checked that by opening a cmd prompt and using the command from the original thread above "adb devices"). As long as you see your device, I think you should be good.
From the "No Command" screen I held down Power and Volume + to get the menu to come up. I then chose the Restart option and immediately held Power and Volume -. This got me into the Fastboot Mode.
Once in Fastboot mode I went to the cmd prompt on my computer and used the following commands in this order from this post:
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot erase system -w
fastboot flash system system.img
fastboot reboot
*Make sure that all of the image files are in the proper location on your computer otherwise this step is worthless
The tablet then rebooted normally and I was able to set everything up again. Again, I am by no means an expert at all, this is just what worked for me. Try at your own risk.
I hope I covered all of the steps, I tried a million different things last night so they all kind of run together.
Click to expand...
Click to collapse
Worked for me! Thanks, I don't believe I had USB Debugging enabled either. Shame it wiped all my data though.
OK, got mine back up and running! I'll just leave what I did here in case anyone can benefit from it.
I first used Wug's Toolkit to download and install the RAW drivers. (Option #4, I believe) They were the only ones that worked for me. I followed the instructions to install them and then when it looped to the No Command screen, I held volume up and power. This got me to the menu, where I chose reboot. I then immediately held down the volume button and power to get into the bootloader screen, where it (thankfully) stopped looping. Then I unlocked the bootloader using the one-click option. Next step was to download and flash factory 4.4 image using the Soft Brick mode. Fastboot recognized my device and pushed the image. Now all is well. Close call... I've already enabled USB Debugging for my wife on this tablet so that crap doesn't happen again. She did lose all her data but she is happy to have a working tablet again instead of a $200 beer coaster.
killswitch11 said:
OK, got mine back up and running! I'll just leave what I did here in case anyone can benefit from it.
Click to expand...
Click to collapse
Worked for me as well. Really appreciate that.
Sent from my Nexus 5 using Tapatalk
killswitch11 said:
OK, got mine back up and running! I'll just leave what I did here in case anyone can benefit from it.
I first used Wug's Toolkit to download and install the RAW drivers. (Option #4, I believe) They were the only ones that worked for me. I followed the instructions to install them and then when it looped to the No Command screen, I held volume up and power. This got me to the menu, where I chose reboot. I then immediately held down the volume button and power to get into the bootloader screen, where it (thankfully) stopped looping. Then I unlocked the bootloader using the one-click option. Next step was to download and flash factory 4.4 image using the Soft Brick mode. Fastboot recognized my device and pushed the image. Now all is well. Close call... I've already enabled USB Debugging for my wife on this tablet so that crap doesn't happen again. She did lose all her data but she is happy to have a working tablet again instead of a $200 beer coaster.
Click to expand...
Click to collapse
I'll give that a go tomorrow. Missed my tablet! Hope it works!
Hi all,
I have a serious problem with my G2 which I could not solve: I used the new LG Flash Tool 2014 with stock KDZ file, everything was going just fine till I received an error message that LG server is not available, I disconnected the USB cable by mistake from my G2 and afterward I saw that it was in the middle of flashing process (12% was completed). I turned it off and tried to reach download mode again and nothing!, I'm receiving the "LG" logo and nothing- the screen goes black (it is still on).
I tried also to connect my phone to the computer- I received a list of 13 "new" local disks "H" to "T", only "H" disk is available and it's showing "image" folder with list of files.
I cannot reach "download mode", nothing is working!
I hope this is not the end for my G2..
please help me
Thank you so much!
If you could receive all those hard disks then you could maybe fix it with linux/ubuntu if you have it. Search for guides to cOpy the neccesary stuff bacK like the bootloader. I can't really help you atm as i am too sleepy.
wulsic said:
If you could receive all those hard disks then you could maybe fix it with linux/ubuntu if you have it. Search for guides to cOpy the neccesary stuff bacK like the bootloader. I can't really help you atm as i am too sleepy.
Click to expand...
Click to collapse
Thank you for your reply. I found this on the sticky threads: "[FIX] NO Recovery mode, No download mode, after OTA on rooted LG G2".
I installed ubuntu and followed the instructions. when I type the following: "gdisk -l /dev/sde" I receive an error message:
"GPT fdisk (gdisk) version 0.5.1
NOTE: Write test failed with error number 13. It will be impossible to save
changes to this disk's partition table!
Problem opening /dev/sde for reading! Error is 13
You must run this program as root or use sudo!"
My device is not rooted, is this the problem?
Please help me!!
Thanks
@NNCa It says you need to run the program as root on ubuntu.
Just use sudo in front of the commands.
You need to type once your password to use sudo, you can't see the password if you enter it for safety I guess but just click enter after you typed ykur password.
wulsic said:
@NNCa It says you need to run the program as root on ubuntu.
Just use sudo in front of the commands.
You need to type once your password to use sudo, you can't see the password if you enter it for safety I guess but just click enter after you typed ykur password.
Click to expand...
Click to collapse
Thank you so much!!
I succeeded to push all the files according to this thread, however I do not see the TWRP menu. I have just constant "LG" logo on screen.
Do I miss something?
Thanks!
NNCa said:
Thank you so much!!
I succeeded to push all the files according to this thread, however I do not see the TWRP menu. I have just constant "LG" logo on screen.
Do I miss something?
Thanks!
Click to expand...
Click to collapse
Well its good you're an step further, try to reboot to recovery using power+volume down i believe or its up idk try both it should say something about wipe data factory reset, press the power button and you are in recovery.
wulsic said:
Well its good you're an step further, try to reboot to recovery using power+volume down i believe or its up idk try both it should say something about wipe data factory reset, press the power button and you are in recovery.
Click to expand...
Click to collapse
Hi,
I powered off my phone by pressing volume down + power for a while ("LG" logo blinked once and phone was fully powered off).
I pushed volume down + power till I saw the LG logo, released it, and pushed again- and finally I reached the Factory Hard Reset screen. I have pushed 3 times the power, and I have got "Factory reset processing..." and nothing is appeared, even when I'm pushing several times on power again.
I guess this is the end of my G2 :crying:
Thank you all for your support, this is an excellent forum!:good::good:
NNCa said:
Hi,
I powered off my phone by pressing volume down + power for a while ("LG" logo blinked once and phone was fully powered off).
I pushed volume down + power till I saw the LG logo, released it, and pushed again- and finally I reached the Factory Hard Reset screen. I have pushed 3 times the power, and I have got "Factory reset processing..." and nothing is appeared, even when I'm pushing several times on power again.
I guess this is the end of my G2 :crying:
Thank you all for your support, this is an excellent forum!:good::good:
Click to expand...
Click to collapse
Nope it isn't the end try to install the recovery again or try to push the custom twrp recovery again to the right partition! Dont give up that fast when i hear your things then its still fixable! you already got the factory reset processing so try to Push the Recovery again and search for an guide about recovery maybe Then you would probably get your device fixed.
Just read my things about simplicity so think easy and you can fix it. AND STAY POSITIVE You will repair your phone today :good:
wulsic said:
Nope it isn't the end try to install the recovery again or try to push the custom twrp recovery again to the right partition! Dont give up that fast when i hear your things then its still fixable! you already got the factory reset processing so try to Push the Recovery again and search for an guide about recovery maybe Then you would probably get your device fixed.
Just read my things about simplicity so think easy and you can fix it. AND STAY POSITIVE You will repair your phone today :good:
Click to expand...
Click to collapse
Thanks, but after connecting the device to linux/windows, it seems that it is not recongized, I do not see the partitions anymore even when typing "ls /dev/sd*" through linux terminal..
NNCa said:
Thanks, but after connecting the device to linux/windows, it seems that it is not recongized, I do not see the partitions anymore even when typing "ls /dev/sd*" through linux terminal..
Click to expand...
Click to collapse
Yeah because the phone has bootloader etc again so maybe you can try this:
http://forum.xda-developers.com/showthread.php?t=2432476
wulsic said:
Yeah because the phone has bootloader etc again so maybe you can try this:
http://forum.xda-developers.com/showthread.php?t=2432476
Click to expand...
Click to collapse
Hi there,
I tried to flash my phone using the lg flash tool, unfortunately it cannot recognized any connected device through USB.. I don't know what else will work for my device
NNCa said:
Hi there,
I tried to flash my phone using the lg flash tool, unfortunately it cannot recognized any connected device through USB.. I don't know what else will work for my device
Click to expand...
Click to collapse
Did you already installed the LG drivers? and checked in device manager or there is like any change when you connect and disconnect your phone?
wulsic said:
Did you already installed the LG drivers? and checked in device manager or there is like any change when you connect and disconnect your phone?
Click to expand...
Click to collapse
Yes, I checked it- no response during connecting/disconnecting the device..
Maybe I did a mistake when trying to push those image files.. I guess there is nothing I can do to fix my phone..
Do you have any other suggestions?
Can someone please help me. How can I get to the LG device- Is there another software I can use to flash files into this device?
Thanks
NNCa said:
Can someone please help me. How can I get to the LG device- Is there another software I can use to flash files into this device?
Thanks
Click to expand...
Click to collapse
Sorry for late reaction but i needed to think of something. Did you tryed to use another cable? Did you tryed to do it on another pc? Did you tryed to maybe install LG PC suite and see if it gets recognized? If you have the PC Suite you may need to turn it off in the LG flashtool idk. Can you tell us more like which windows you have?
wulsic said:
Sorry for late reaction but i needed to think of something. Did you tryed to use another cable? Did you tryed to do it on another pc? Did you tryed to maybe install LG PC suite and see if it gets recognized? If you have the PC Suite you may need to turn it off in the LG flashtool idk. Can you tell us more like which windows you have?
Click to expand...
Click to collapse
Hi,
I tried all you suggested, however my devide is not recognized. I tried to use the LG PC Suite and to flash by IMEI, however it is still saying that no device was connected.. I checked windows device manager, and nothing changed there.
There is any chnage I can see my connected device? use some tool or another software?
Thank you again for your patience and help!
NNCa said:
Hi,
I tried all you suggested, however my devide is not recognized. I tried to use the LG PC Suite and to flash by IMEI, however it is still saying that no device was connected.. I checked windows device manager, and nothing changed there.
There is any chnage I can see my connected device? use some tool or another software?
Thank you again for your patience and help!
Click to expand...
Click to collapse
Hi, sorry to say but you have unfortunately completely hardbricked your device. It happened to me too however I was able to get it replaced under warranty at no extra cost.
What happened was that when your phone was still detected by linux, you had a chance to recover by flashing the correct partitions to gain access to download mode and from there, flash a KDZ to go back to complete stock. However, the files you used were probably incompatible with your variant which has now corrupted your bootloader sequence. I suggest you read this reply by fizzy177 as well as the rest of the thread: http://forum.xda-developers.com/showpost.php?p=51522304&postcount=118
So right now, you cannot do anything as you have already found out, no computer will recognise that your phone is plugged in. Your phone fails to boot when you try enter the download mode and it just freezes on the splash screen which looks like this: http://www.lg-phones.org/wp-content/uploads/2014/03/image2.png
What's meant to happen is your phone should load past that initial splash screen into this http://www.androiddunya.com/wp-content/uploads/2014/01/LG-G2-DownloadMode.jpg which accepts KDZ flashing and warns the device has been rooted.
So it's a blessing that your phone cannot boot as LG cannot find out you have voided warranty and you will be able to get a replacement free of charge.
Issue was solved- device was fixed under warranty
Hi,
I just want to update you all that my device was fixed under warranty! (motherboard replacement)
Thank you all for help and great support, this is a great forum with great community :good::good:
Hello
From past 2 weeks i am wondering on internet for a solution . Hours and hours of surfing and articles but still
Hope some one solve this issue.
Okay. First i m using LG G2 F320 K update to lollipop . Non rooted. It was working fine . I can transfer files in MTP .
But about a month ago i get an update for my phone . And after some days i need to transfer some files to my phone , i wonder when i connected my phone to computer nothing happened . No notification on mobile for changing PTP MTP option . Also nothing happened in Computer device manager..
From that day i am unable to connect my phone with windows 10. It always charging mobile.
I uninstalled all drivers in device manager and installed from LG website. I updates windows N and NK MTP update from windows for windows 10.
I changed different data cables and different computers and different ports . All stuff i can do. Still no luck.
When ever i plug USB data cable it always put my Mobile on Charging . No notification on Mobile. Also i go in setting > storage> and there is no option in upper right corner to select USB PC connection .
I am in developer mode and debugging mode is on also. Also USB tethering option is Disabled .
Kindly some one help me regarding this.
LG G2 F320K updated to stock Koren lollipop 5.0.1 . Non root.( i updated lollipop in April 2015)
Issue i am facing is no notification for Charging/ MTP/PTP Usb Debugging on mobile notice bar when i attach my phone using USB cord with computer. Also in computer device manager nothing happen. Even i checked on windows 10 , 8.1, 8, 7 .
I remember it was working like charm 4 weeks before I can change MTP PTP or Charge only mode by selecting notification when i attach it to my laptop. I can transfer files can use LG PC suit .
Then i received an software update like 40 mb and i updated my mobile. That i remembered.
After that 2 weeks before i need to transfer some books from laptop to my mobile. When i plugged my device there no notification to select MTP mode . Also there is nothing happened in my windows 10. I looked in task manager. No yellow icon in computer task manager for driver thing.
Laptop is just silent and mobile is just on charging .
Then i go to setting in LG and looked for USB PC connection settings. I wonder there is nothing . Settings > storage > 3 dot in upper right corner.. it suppose to be there . But here is no 3 dot in storage. Then i looked into share and networks in android setting and i found that USB tethering. But its faded mean it is disabled and i am unable to use this feature also.
I tried on different computers different cables , original, but nothing. Always when i plug usb mobile went on charging and in all computers nothing happen in device manager.
USB debugging is on.. I factory reset device 2 times. but useless. Also i uninstall all drivers from my laptop and then reinstall drivers from LG website also i tried google drivers , ABD, different ports. Nothing nothing happen.
Also now if i try put mobile on download mode by turning device off and then push + vol button and then put cord in mobile . No download mode also it went on charging. Well charging from laptop or from charger is okay.
Hope i explain all.
bought this phone used and I don't think it was rooted but never checked, confirmed. Last night it turned off and will not turn on anymore..
Tried the pwr button for several minutes and no change. Plugged it in with several different cables and no change.
Any other suggestions or options? USB to computer detects something but says it can't install the driver.
Any ideas?
oNe
Can you enter to the bootloader menu? Maybe you can enter recovery and wipe the cache and dalvik
martinfarrell11 said:
Can you enter to the bootloader menu? Maybe you can enter recovery and wipe the cache and dalvik
Click to expand...
Click to collapse
negative, either the phone is totally dead or the screen is dead but NOTHING happens when pwr is pressed
here is what I have tried:
1. Press and hold PWR button for over 3minutes
- Plugged in and unplugged into ac - no change
2. Press and hold volume DOWN + Pwr for over 3minutes
- Plugged in and unplugged into ac - no change
3. Plugged into different a/c power outlets with 2 different chargers - no change
NOT sure what else to try or do?
Funny thing is if ya plug into a computer it does indeed detect "something'
However it says it can't load the USB drivers something about QU_***
Open to any ideas and suggestions.. WHILE I would love to get the phone working whats more high priority for me now is the 20gb's of pics that apparently did NOT back up.
oNe
Sean Price said:
Funny thing is if ya plug into a computer it does indeed detect "something' However it says it can't load the USB drivers something about QU_***
Click to expand...
Click to collapse
Funny thing is- that "something" is the solution to your problem. Capture the error message completely and search the 6P forums for that. Several threads on the "something" issue.
v12xke said:
Funny thing is- that "something" is the solution to your problem. Capture the error message completely and search the 6P forums for that. Several threads on the "something" issue.
Click to expand...
Click to collapse
Several threads with no solution. I went through the same "something" . Can't be fixed
v12xke said:
Funny thing is- that "something" is the solution to your problem. Capture the error message completely and search the 6P forums for that. Several threads on the "something" issue.
Click to expand...
Click to collapse
fixed that issue, aka QHSUSB_BULK is now working properly according to Device Manager.. but Nexus 6P is not detected, and doesn't even show up in Disk Management either.
Any other ideas?
please advise..
oNe
Sean Price said:
fixed that issue, aka QHSUSB_BULK is now working properly according to Device Manager.. but Nexus 6P is not detected, and doesn't even show up in Disk Management either. Any other ideas? please advise.. oNe
Click to expand...
Click to collapse
If you found the right EDL_9008 thread, there is Qualcomm software to download for your PC. If your phone is in the right downloader mode you can use the PC software with a special recovery.img. I don't know anything about it, just read through the threads long ago. It's a mixed bag with some success stories, some not. Keep looking though, I think you are on the right track. The original poster was "Tenfar" if I recall correctly. Good luck.
Try cleaning out the charging port.
Hi there,
I think we are in the same/similar boat. My phone shut off while using it (screen froze, then went black) and seems to have bricked itself. I *am* able to get mine to turn on, but only about once per day after it has been left plugged in for a few hours (although there is no indication it is charging while plugged in - never gets warm, no lights, etc.) I can get into recovery if I am lucky (usually get to the android bot laying on its back, then PWR+VOLUP just causes the phone to shut off instead of actually getting into recovery menu.) I've been able to clear cache/factory wipe from recovery menu with no luck. I never did unlock the bootloader so I am unable to use fastboot to do anything. I tried to flash a few OTA (full and incremental) images using adb when I am able to get into recovery, but they always failed in one way or another.
I've been trying the methods described in the 'tenfar' threads - using the xiaomi flasher and QPST tools. The xiaomi tool always fails for me. I have been able to get the QFIL tool to successfully 'download' about 3 times now, with tenfar's recovery images. However, after the success message, the phone doesn't do anything (I read in other threads it should reboot itself) - and after unplugging, the behavior of the device seems to be the same - just stuck and won't turn on at all.
Right now I think I am stuck in 'EDL' mode where the only evidence that the device isn't completely dead is that it shows up in device manager as 'Qualcomm HS-USB QDLoader 9008 (COM3)', and the factory imager tools do recognize it.
It *seems* like the only way forward is to somehow get one of these factory tools to flash the right set of files onto the device - I've tried a few now with no luck. I even tried extracting the relevant *.img files out of the google factory image download and replacing tenfar's image files with them. I was able to load those onto the device with QFIL. This morning my attempt at turning on the device has me stuck on the white google logo, which is new behavior for me - usually it shows the logo for ~5-10 seconds then the device powers off. I've left it on for a while stuck on the white google image, but I'm not sure if I'm doing anything useful here.
Here are my reference threads:
tenfar's 'debrick' thread
QFIL thread
If anyone has any crazy ideas, I am open to try them. Thank you.
Maybe disable big cores?
apples1678 said:
Hi there,
I think we are in the same/similar boat. My phone shut off while using it (screen froze, then went black) and seems to have bricked itself. I *am* able to get mine to turn on, but only about once per day after it has been left plugged in for a few hours (although there is no indication it is charging while plugged in - never gets warm, no lights, etc.) I can get into recovery if I am lucky (usually get to the android bot laying on its back, then PWR+VOLUP just causes the phone to shut off instead of actually getting into recovery menu.) I've been able to clear cache/factory wipe from recovery menu with no luck. I never did unlock the bootloader so I am unable to use fastboot to do anything. I tried to flash a few OTA (full and incremental) images using adb when I am able to get into recovery, but they always failed in one way or another.
I've been trying the methods described in the 'tenfar' threads - using the xiaomi flasher and QPST tools. The xiaomi tool always fails for me. I have been able to get the QFIL tool to successfully 'download' about 3 times now, with tenfar's recovery images. However, after the success message, the phone doesn't do anything (I read in other threads it should reboot itself) - and after unplugging, the behavior of the device seems to be the same - just stuck and won't turn on at all.
Right now I think I am stuck in 'EDL' mode where the only evidence that the device isn't completely dead is that it shows up in device manager as 'Qualcomm HS-USB QDLoader 9008 (COM3)', and the factory imager tools do recognize it.
It *seems* like the only way forward is to somehow get one of these factory tools to flash the right set of files onto the device - I've tried a few now with no luck. I even tried extracting the relevant *.img files out of the google factory image download and replacing tenfar's image files with them. I was able to load those onto the device with QFIL. This morning my attempt at turning on the device has me stuck on the white google logo, which is new behavior for me - usually it shows the logo for ~5-10 seconds then the device powers off. I've left it on for a while stuck on the white google image, but I'm not sure if I'm doing anything useful here.
Here are my reference threads:
tenfar's 'debrick' thread
QFIL thread
If anyone has any crazy ideas, I am open to try them. Thank you.
Click to expand...
Click to collapse
I have the 100% same issue. Screen froze,then went black and now its stuck in EDL mode. I need my data. Recovery access or anything else would be fine/enough for me. I have had LineageOS and TWRP on the device. With TWRP i can access my data.
How have you got your device on? Mine dont start once a day or so. Its always in EDL mode ( 9008 ).
ncc8uetou5et said:
I have the 100% same issue. Screen froze,then went black and now its stuck in EDL mode. I need my data. Recovery access or anything else would be fine/enough for me. I have had LineageOS and TWRP on the device. With TWRP i can access my data.
How have you got your device on? Mine dont start once a day or so. Its always in EDL mode ( 9008 ).
Click to expand...
Click to collapse
Sorry bud - I never was able to get any further than when I posted this. I eventually gave up, got a full out of warranty refund through my CC after the manufacturer wouldn't help me at all, and upgraded to a Pixel XL. I still do have the device, I should try to boot it up again . I didn't have any data concerns on my device so I was able to give up... good luck!