OK I have had my T-mobile Wing aka HTC Herald since last April.
Just a few days ago I encountered a problem with my lcd. And I would like your guys feedback if possible before I purchase an lcd replacement.
My problem is when I slide open the wing my screen starts to fade, (almost making it look like a negative from a picture) after that it starts to fade to different colors.
Now the problem persists when the phone is closed, however if I tap the top of my wing and hold it the screen becomes normal, but once I let go it starts to fade again.
I would like to know if any of you experienced this with ur phone and if a replacement lcd screen will fix the problem or am I sol?
If it helps im running my wing on Open Touch v6.0 WM 6.1 Build 20273.1.3.3
Thanks in advance.
LCD problems
Hello,
I too have some weird LCD problems and instead of creating a new thread I thought of posting in this one.
For the past few months, whenever I get a call or resume my phone from standby mode using the power button the entire screen goes white or sometimes it has green or blue colored lines all over them. I have to keep on pressing the power button few times to get proper display. Also whenever I open the qwerty keyboard the display goes blank. Since I am out of warranty Tmobile is not ready to replace the phone and I contacted the HTC customer service and they told that the display unit and some hardware stuff is gone and it needs to be replaced and will cost a minimum of 170$ and will increase if they had to replace some other hardware.
Please note that, my screen is NOT broken and the touch screen too works fine. Recently the display has gone completely blank or too faded even to see whats there in the screen I could barely see the today screen.
I searched and I did not find any similar issues that other folks have faced. Since the LCD and the touch screen is not broken replacing them is not going to fix the issue, correct? I was using open touch and recently I updated the latest official Tmobile release of ROM 6.26.xxx. I also tried the hard resets too.
Any other ideas/suggestions will be of great help for me. Thanks in advance.
I am having some similar problems as well, but my problem is much more severe. My screen is completely black and it just happened this past weekend. When i slide the phone the screen used to flicker but now it black as well. Phone works fine but is useless due to the fact the the screen is out. I remember seeing a program where you can interact with your phone via your pc when something was wrong w/ your screen (cracked, broken, etc.) I have searched the forum but to no avail. The program was very simple and effective. I plan on replacing my phone but would like to retrieve some info off the one I have. I just need that program! Anyone please HELP US!
handsome22 said:
I am having some similar problems as well, but my problem is much more severe. My screen is completely black and it just happened this past weekend. When i slide the phone the screen used to flicker but now it black as well. Phone works fine but is useless due to the fact the the screen is out. I remember seeing a program where you can interact with your phone via your pc when something was wrong w/ your screen (cracked, broken, etc.) I have searched the forum but to no avail. The program was very simple and effective. I plan on replacing my phone but would like to retrieve some info off the one I have. I just need that program! Anyone please HELP US!
Click to expand...
Click to collapse
link to the thread containing some info about the software... its called my mobiler
thanks for the info
touchscreen was working today morning, took battery out for 2 hours, turned it back on and it was working abit weird, and now i cant press any touchscreen buttons atall!
So no softkeys (pick call, home etc.) and nothining on the big screen! I can turn on the phone, press the power button and volume buttons, see my home screen get calls etc.. hard reset twice, took battery out, nothing does it .. gonna try flash it but dont think itll do it ... and ideas?
Im in uk aswell if that makes a diff
Dear All,
I have similar problem. Usuallí I use on my HD NRG ROM. About 3 weeks ago I updated to the latest NRG WM 6.5 23xxx ROM with Sense 2.5 Maxmanila version, and since this upgrade the touch screen position moving randomized up or down from 2 mm to 30mm!!! After this ROM I tryed updating each newer version, but not changed nothing. I need realign the screen about 10 times / day!!! The phone I never dropped or cracked.
Can help me somebody what happened with my HD?
I had this happen to me yesterday. I was surfing on my phone as per the norm. Put my phone down. Got a txt, picked it up and it wouldnt allow me to access it. I thought it must be a freeze as it has happened occasionally.
So I restarted.............and nothing. No response AT ALL from the touch screen.
I have noticed the oily spot problem on the most part of my screen, and thescreen doesnt have that little give it used to when using it (paranoia possibly)
So I can only assume something has given within the screen. Ive been searching all day on the internet for causes and fixes but nothing has come up.
The volume and power buttons work but I cant do anything at all with the phone as its obviously all touch based.
Is this a screen replacement job then or is the whole phone goosed?
Roheelshah if you turn your phone off do you have the massive oily screen thing?
Any help is most appreciated....
I had the same thing, a oily spot, but it was there for months, then i noticed another new spot (looked like a tiny tiny burn) and thats when it stopped working completely... ive ordered a new screen which should be comming in a few days, im hoping thats the issue
will let you know if it works ....
keep me updated if you find anything
thanks!
NECROSTONE said:
I had this happen to me yesterday. I was surfing on my phone as per the norm. Put my phone down. Got a txt, picked it up and it wouldnt allow me to access it. I thought it must be a freeze as it has happened occasionally.
So I restarted.............and nothing. No response AT ALL from the touch screen.
I have noticed the oily spot problem on the most part of my screen, and thescreen doesnt have that little give it used to when using it (paranoia possibly)
So I can only assume something has given within the screen. Ive been searching all day on the internet for causes and fixes but nothing has come up.
The volume and power buttons work but I cant do anything at all with the phone as its obviously all touch based.
Is this a screen replacement job then or is the whole phone goosed?
Roheelshah if you turn your phone off do you have the massive oily screen thing?
Any help is most appreciated....
Click to expand...
Click to collapse
download and install this _HTC Touch HD_TouchHD system.exe
BOLDESH said:
download and install this _HTC Touch HD_TouchHD system.exe
Click to expand...
Click to collapse
whats it do? and where from??
I just posted something like this a few days ago, pulled my phone out and screen wouldnt respond, had these marks all over my screen, "swirly marks" as i describe it, very well could be the oily marks you are talking about. you can move them around with your finger right?
anyway, i took my sim out, tryna find a spare phone, couple hours later the marks were gone and screen started working again, touch wood its been fine since.
no idea what happened, but try letting it air out or something
ok basically i received a new digitizer today (the actual touchscreen) ...
i dismantled the whole phone using the service manual and some video some guy made (VERY HELPFUL, if anyone wants it for any reason i can post a link), ok so i got rid of all the top bits, the circuit boards (or watever theyre called)
I got down to just the bezel, lcd and digitizer (dont know what a bezel is, the lcd is where the display actually is and digitizer is directly stuck ontop of that)
Apparently when replacing the screen, htc have made it so that you have to replace all three of those parts instead of individual ones, but you can buy them seperately so i thought i'd hero it.
i poked out the screen from the frame (some chewingum like stuff holding it in) then i started peeling off the digitizer (if you get one and want to try it you'll know where to peel) ... this was a mistake tho cause the lcd is unbelievebly sensitive so while peeling off it left scratches on the lcd, and me not knowing the lcd is sticky tried to wipe them and use a dust free cloth, which left alot of crap on the actual lcd!
i managed to get the digitizer off and ripped the cable that goes from digitizer to whatever reads our fingers on the screen, took it all off, placed the new one directly ontop and fed the wire exactly how it was for the first screen.
Put it all together again
Now I did mess up my screen badly, but in a good way! .. i now have full touchscreen working (smoother than ever) but my LCD display is near enough gone, so it looks like the screens really really dark, and i have to tilt it at certain angles to see the screen..
After all of this i now have a touch hd i can controll from my pc (using mymobiler) so i can recieve calls, send texts all from my pc when connected thru active sync, can even play teeter ... but not really the same!
I wouldnt recomend anyone to try what i did, although i think its worth the risk as I would have to replace the lcd anyways if i wanted a new screen in the first place... and who knows you might be able to peel the digitizer off clean (NEVER EVER EVER TOUCH LCD WITH ANYTHING!!!).
It all cost me around 10-15£ for the digitizer and screwdrivers and alot of hours dismantling phone compared to 50-100£ for a new lcd.
I am either going to get a new lcd now so i can actually see the screen, or get a new phone.
Sorry for the essay but hopefully this helps someone in any similar situation
if i do get a new lcd will post how it goes and if it sorts out everything
if anyone knows of any other reasons why my lcd would be so dim (brightness is 100%) accept for me getting carried away with it ... help would be appreciated
the_cool said:
I just posted something like this a few days ago, pulled my phone out and screen wouldnt respond, had these marks all over my screen, "swirly marks" as i describe it, very well could be the oily marks you are talking about. you can move them around with your finger right?
anyway, i took my sim out, tryna find a spare phone, couple hours later the marks were gone and screen started working again, touch wood its been fine since.
no idea what happened, but try letting it air out or something
Click to expand...
Click to collapse
Yeah swirly oil marks is how myne started ... i think i finished off the screen by trying to press hard on the mark to try and clear it .. . so be careful with it.. but think that overall the screen had seen better days (course only a few weeks after warrenty finishes) ... all conections inside were ok aswell
doczyus said:
Dear All,
I have similar problem. Usuallí I use on my HD NRG ROM. About 3 weeks ago I updated to the latest NRG WM 6.5 23xxx ROM with Sense 2.5 Maxmanila version, and since this upgrade the touch screen position moving randomized up or down from 2 mm to 30mm!!! After this ROM I tryed updating each newer version, but not changed nothing. I need realign the screen about 10 times / day!!! The phone I never dropped or cracked.
Can help me somebody what happened with my HD?
Click to expand...
Click to collapse
Same here. Touch screen not working. Phone never flashed, droped,...
Any solution?
unfortunately, a friend of mine changed the touchscreen without success. Phone was in perfect state, no drop, no flash. Just the touch not responding. I'm not sure that changing whole part lcd+digitizer solve the problem.
Hi all!
I've got similar problem with my touch HD. It's stock since I bought it. My touch sense was acting weird, like it wasn't properly calibrated. Like, when I press 7 on phone pad, the phone actually presses 1, and if I press 0, phone presses 5 and so on..
I've tried to align the screen, but it doesn't get aligned the first time. I have to repeat the process about 4 times before it gets aligned. That's good for about few minutes and the problem is back. Hard reset was also done, 2 times.
Could this be a fixed with a software update? Does this mean that digitizer will soon be dead?
Thank you for your help
Regards
igothtc2 said:
Hi all!
I've got similar problem with my touch HD. It's stock since I bought it. My touch sense was acting weird, like it wasn't properly calibrated. Like, when I press 7 on phone pad, the phone actually presses 1, and if I press 0, phone presses 5 and so on..
I've tried to align the screen, but it doesn't get aligned the first time. I have to repeat the process about 4 times before it gets aligned. That's good for about few minutes and the problem is back. Hard reset was also done, 2 times.
Could this be a fixed with a software update? Does this mean that digitizer will soon be dead?
Thank you for your help
Regards
Click to expand...
Click to collapse
use ScreenCal to fix it, hopefully it can help you
Hakim Rahman said:
use ScreenCal to fix it, hopefully it can help you
Click to expand...
Click to collapse
Hi!
I've successfuly installed the cab file on my phone's sd card, but the problem is still there. I don't know where the installed files are, do I have to run this application?
Thank you for your help!
Regards
igothtc2 said:
Hi!
I've successfuly installed the cab file on my phone's sd card, but the problem is still there. I don't know where the installed files are, do I have to run this application?
Thank you for your help!
Regards
Click to expand...
Click to collapse
have you hard reset the device after installing the cab file ?? if not do it and see if there are changes...
Hakim Rahman said:
have you hard reset the device after installing the cab file ?? if not do it and see if there are changes...
Click to expand...
Click to collapse
Just did the hard reset. When it asked me to align the screen, I just couldn't align the top left corner. I had to press it like 50 times before cross went to the lower corner. Otherwise, after the align it's good for about couple of seconds and then it's just pressing all over.
I thought I had just some software issues because the screen wasn't dead, it responded to my touch. So, I'll probably have to buy a new screen and digitizer, right? Or do you have any other ideas?
Thank you again for your help!
Regards
firstly screencal installs calibration settings not for blackstone so do not install it, no point. (btw it also increases device touch sensitivity)
secondly you guys should try and install the calibration settings for blackstone, basicly what the align screen does, not sure where to find them for download but i could post the registrys if someone wants to make a .cab from them. (atm i cba making the .cab but i am able to do it )
if the calibration settings do not work i think it is best to buy a new lcd package (or buy new device and give me old one for spares oj)
Rn
hi buddy ! What you mean GSensorCalibrator ??
i didnt mention anything about gsensor calibration dude.
tried and tested screencal the other week and it screwed my blackstone.
install these instead:
*screen calibration, sets the blackstone touch points: (aligning the screen)
if you install a cab with these registrys it should fix the alignment problem.
(if it doesnt then its hardware issue = lcd etc)
[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\TOUCH]
"MaxCalError"=dword:8
"CalibrationData"="511,542 183,881 183,198 834,197 833,880"
*this one will maximise the touch sensitivity for those that want it:
[HKEY_LOCAL_MACHINE\Drivers\TouchPanel]
"PressureThreshold"=dword:0
Rn
Does anyone have a recommendation where you can buy a digitizer and lcd from?
Hello,
Since a few days, the touch input of my front (LCD) screen stopped working. Nothing looks damaged, the screen still displays what it is supposed to, but there is no reaction to my inputs (actions on volume and power buttons do work, as well as on the e-ink screen). Did this happen to any of you? Any suggestion on possible ways to fix it?
I should also mention that it still works by moments, like half a day working, then 2 days not responding, etc. I tried shaking it in different ways should a connector be slightly displaced, with no success: the few times it started working again came like a (good) surprise. I also had the great idea to do a factory reset, so now the phone is stuck on the Android configuration wizard, which must be done on the front screen (no possibility to use YotaMirror, apparently).
Thanks!
wicoz said:
Hello,
Since a few days, the touch input of my front (LCD) screen stopped working. Nothing looks damaged, the screen still displays what it is supposed to, but there is no reaction to my inputs (actions on volume and power buttons do work, as well as on the e-ink screen). Did this happen to any of you? Any suggestion on possible ways to fix it?
I should also mention that it still works by moments, like half a day working, then 2 days not responding, etc. I tried shaking it in different ways should a connector be slightly displaced, with no success: the few times it started working again came like a (good) surprise. I also had the great idea to do a factory reset, so now the phone is stuck on the Android configuration wizard, which must be done on the front screen (no possibility to use YotaMirror, apparently).
Thanks!
Click to expand...
Click to collapse
i recommend reflash it. possibly and more strongly recommend to flash the same version and region which was installed for example HongKong 4.4.3 baseband number .HK1.0.36a
ftp://fw.ydevices.com/YotaPhone2/Firmwares/
Actually, I forgot that the front screen was replaced several months ago (by a repairer that mistakenly changed the front screen instead of the e-ink one which was having an issue).
The factory reset didn't improve the situation, the front screen becoming "touch-insensitive" every few days. After checking how the screen connectors are supposed to be plugged (opposed to the screen), I noticed that gently tapping the phone front screen down helped to solve the issue each time it happened. A few days ago, I finally opened the phone (quite easy, there are two useful videos online) and unplugged/replugged the screen connector. It has been working fine since then.
If it happens to anybody (who would have its front screen replaced), I hope it can help!
I recently replaced the screen on my K20 Pro and I noticed that there are a few malfunctions. Screen brightness suddenly goes max for a few seconds when using opening the phone from lock screen and usually when using fingerprint to unlock (I have my Auto-Brightness set to off). Ghost touches when tapping but none when swiping. I was wondering if this is a common malfunction after replacing the screen (calibration or something) or did the installation of the screen went wrong or is it because the LCD used to replace the original one was defective. Thanks for the insights.
i just replaced my screen four days ago and so far i got no problems of some sort..
so, i think it's probably the installation or the unit's fault. idk tho
I'm just annoyed by the sudden screen brightness max. To be honest I think the ghost touch thing is because of a defect LCD, but I think the brightness problem is from the system. It's like the phone does not recognize or remember the previously set brightness. I hope there's a solution for this. Do factory resetting the phone solve any brightness problems?
hello! did you managed to solve this problem? I have the same problem
if you removed foil and it still touch in random parts of screen,. then send it back. i had the same symptoms with a few screens that I repaired. just Chinese quality
yaro666 said:
if you removed foil and it still touch in random parts of screen,. then send it back. i had the same symptoms with a few screens that I repaired. just Chinese quality
Click to expand...
Click to collapse
i did the replacement with not 100% compatible display...because it was way cheaper than the display I needed...(from an oppo phone) i know it sounds weird but the display was 200 dollars( the 100% compatible from oppo) and i payed like 70 for this display that flickers the bringtness..but they told me a factory reset can solve it?
what do you think?
try, but I doubt it. looks like fauly/not compatible to me.
try flashing latest miui to make sure you did everything to get it to work, if that doesn't make it better just don't waste your time. if you have more technical data on both anoled and lcd with connections described (every pin) then you could make research a d bypass if needed. otherwise send it back
vincedrian said:
I recently replaced the screen on my K20 Pro and I noticed that there are a few malfunctions. Screen brightness suddenly goes max for a few seconds when using opening the phone from lock screen and usually when using fingerprint to unlock (I have my Auto-Brightness set to off). Ghost touches when tapping but none when swiping. I was wondering if this is a common malfunction after replacing the screen (calibration or something) or did the installation of the screen went wrong or is it because the LCD used to replace the original one was defective. Thanks for the insights.
Click to expand...
Click to collapse
managed to solve? I have the same problem, besides sometimes the screen seems to lose sensitivity, I saw in some groups people recommend buying parts from the dragon-tt store....I'm thinking of taking a chance....