Hi,
I installed the oreo android on the b09 version via the recovery mode. The installed version is A2017GV1.3.0B03. Unfortunately the camera screen is black. In the snapchat application, the front camera started, but the back unfortunately remained black. What could have happened and how can I fix it easily?
Related
I recently upgraded my phones firmware from 4.3 to 4.4 everything was working fine until a few days later the camera suddenly stops working. It just shows black but all the buttons on the camera app is there. When I switch it to the front cam its working but on the rear its not.
I tried to test it using *#0*# it shows data line failed and camera failed. I tried flashing it again and doing a factory reset but nothing works. I tried replacing the camera module but still not working. Does this mean my board is broken or something?
Need Help. thanks!
stryker05 said:
I recently upgraded my phones firmware from 4.3 to 4.4 everything was working fine until a few days later the camera suddenly stops working. It just shows black but all the buttons on the camera app is there. When I switch it to the front cam its working but on the rear its not.
I tried to test it using *#0*# it shows data line failed and camera failed. I tried flashing it again and doing a factory reset but nothing works. I tried replacing the camera module but still not working. Does this mean my board is broken or something?
Need Help. thanks!
Click to expand...
Click to collapse
I've got the same problem on the same phone. My phone wouldn't power on and had to have it's ic replaced. After that the wifi wasn't working so I flashed to 4.4 and that fixed that but the camera isn't working. When I test *#0*# the front facing camera is working but the rear show the same errors as above. When I open the camera it shows a black screen and says 'firmware is updating please wait' and nothing happens.
On typing *#34971539# and then pressing Phone/CAM FW Ver Check I get these:
Rear facing camera
Cam FW Ver: NONE
Phone FW Ver: S13F0SAGI01
The front facing camera has
Cam FW Ver: S5K6B2YX
Phone FW Ver: S5K6B2YX
Any help would be appreciated!
Did you guys get any solution for this issue? I'm having the same problem with my I9505 ... help is appreciated from any body
Well i guess i joined you with the same issue.
I'm going through the same problem now
exactly the same problem
Hi there
I've just replaced the screen of my P8 lite. I booted, everything working fine in Lollipop. so i start downloading the update to 6.0 via the updater app.
it just casually installed the update, went to the screen with percentage of how far the update is at. It finished, 100% then decides to reboot and poof, only black screen, no boot up screen or all the other stuff. Just a plain Black LED Backlight.
I've tried downloading the 6.0 to 5.0 firmware on my sdcard in dload map. when i boot the phone by holding volume +, volume - and power button, it just boots back in the black screen, not starting the update.
I've also tried other firmware the site offers.
Here is some information about my device:
Huawei P8 lite ALE-L21
Which steps should i consider taking here?
thanks in advance
Update: apparently it's just some problems with the hardware of the screen, since when i press volume +,- buttons it still makes sounds, and double tap takes a photo. But isn't it still quiet strange that right when the update hits 100% it started malfunctioning?
So guys, I've tried to restore to the previous version after flashing a new android version on my Yotaphone2 but it seems that I screwed up. It seems that the front screen plugin is broken since the SO is working fine on the back screen.
Is there a way to fix this?
PS: The screen is like this even in the recovery mode... and the back screen touch is not working anymore :crying:!
I've updated my 6T to OxygenOS 10 successfully and factory reset my phone after the update as well. The phone now has a stuck yellow ting everywhere but on the lock screen?
Any have any idea whats gone wrong or how to fix it?
I'm in the same situation but then i tried changing display settings in below location
Display -->Screen calibration
In the Advanced setting you can go for
1.AMOLED Wide gamut
2. Display P3
Where you can avoid that yellow tint
sounds like night mode is on always on night mode did you have any magisk mods installed and if you use xxx rom you needed to uninstall and reinstall after you boot 10
hello,
I'm having a problem with my camera. I installed the mod "PIXELFY" or someting like that on lineageos 17 by pig, the phone rebooted and the camera opened during the boot, then bootloop. I tried a data format, but the rom didn't boot at all, and the camera stays open. I reflash the rom, the camera app detects the popup but can't close it...
Any ideas? Thanks.
EDIT : Solved by flashing the stock miui rom