So my brother's zuk z2 has been broken for months now, and no repair shop could repair the phone.
I did a lot of digging and i found out that zuk z2 has a problem with quick charge 3.0 (It technically supports it but it doesn't have the necessary hardware for it)
If your zuk z2 (plus) has these symptomes this fix is guaranteed to work
Not charging.
Not turning on (Sometimes it might turn on).
Notification light blinking.
Heating in the lower part of the phone near the charging port. (If your zuk doesn't do that, then removing the cx chip will only disable fast charging)
The problem:This tiny chip with cx on it: https://i.imgur.com/YD8Eh2b.jpg
This chip is responsible for quick charge and it only supports quick charge from the original charger (that is what i was told).
When charging with an qc charger it may short out. That is where the heat is coming from.
The solution
You need to remove that chip.
You can just pry on it with a screwdriver and it pops out like its meant to do that.
Anyone can do this procedure at home, but you need a phone repair kit(<1$ online).
Or you can take your phone to the local repair guy and send them a link to this guide.
If you decide to do this by yourself i advise you to watch a teardown video, because there are some plastic tabs that you don't want to break.
1) First off, remove the sim card tray and then you need to remove the back glass, use a hair drier at the lowest setting and heat the lower part of the back of the phone (where the zuk logo is) around the perimeter.
When the glass is hot, use a suction cup to lift the glass and then use a plastic tool (only plastic tools) to slice the adhesive.
Try the suction cup method 3-4 times with heating, because the suction cup may not be strong enough to lift the glass up.
If the suction cup is not strong enough to lift the glass away, use a very thin and short piece of metal, wedge it between the glass and the plastic body (this will slightly damage the plastic) and the glass should pop out if it's hot.
Be very careful at the left upper side of the phone (the camera side) because there is the volume and power button ribbon and the battery ribbon. You don't want to damage those.
This is maybe the hardest part of this teardown.
This is how it looks like once the back cover is off: https://i.imgur.com/XGD5m7F.jpg
2) Because the chip is on the back side of the motherboard you will need to remove almost every component except the battery and some other smaller components.
Remove all screws.
Attention! one screw is under the battery ribbon.
Then try to remove the plastic.
The top plastic piece needs to be pulled from the opposite side of the back camera because there is a plastic latch near the back camera.
Pull that plastic piece up and then to the left (away from the back camera).
The lower plastic piece should be pulled from the upper most part, but it should be pulled first up and then pulled towards the top side.
If the piece doesn't move you need to remove residual adhesive or try to remove the lower plastic piece from the headphone jack side.
This is how it should look like without the plastic top cover: https://i.imgur.com/qEtXTg7.jpg
This is how it looks like without the bottom plastic piece:https://i.imgur.com/RlVhDQK.jpg
The problematic chip is in the red circle, but it is on the other side of the motherboard.
3)Unclip the connections, the antenna connectors, and the selfie camera.
By this point you should have removed the sim card tray, if not remove it NOW.
4)Remove the motherboard with the back camera (its held with some copper tape).
Inspect the charging port.
It should look something like this: https://i.imgur.com/bKiN5tG.jpg
The chip is very small.
This is how the chip looks like when removed: https://i.imgur.com/fCSJBds.jpg
This is the chip you want to remove: The one with CX on it!
This chip: https://i.imgur.com/YD8Eh2b.jpg
5)Remove the chip with something made out of metal, like a screwdriver.
6)Reassemble the phone and enjoy your charging phone.
Also this is why you would want to do it yourself.
This is what a "repair guy" did to the phone: https://i.imgur.com/5BiMn6s.jpg
He said that there was a short on the motherboard and the phone is completely dead.
The phone works, but now i don't have a power/volume button.
He obviously used a metal tool, as seen by the scratches left on the metal inside the phone.
So don't use a metal tool.
Edit: Removing this chip will only disable fast charging, if your device is perfectly working, or has different symptomes, don't remove this chip.
Edit2: The thread was broken,(only one image was showing). My dumb ass inserted the images wrongly.
Will removing this enable quick charge 3.0 support on our device ?
troublesom said:
Will removing this enable quick charge 3.0 support on our device ?
Click to expand...
Click to collapse
No
My phone is bot charging. So will removing this chip make it charging again??
And how it is so that without that chip it will work properly??
Does OTG work after removing it?
Sandeep7974 said:
My phone is bot charging. So will removing this chip make it charging again??
And how it is so that without that chip it will work properly??
Click to expand...
Click to collapse
Don't remove it .it regulates charging speed and safety
spandu500 said:
Does OTG work after removing it?
Click to expand...
Click to collapse
It does.
zuk z2 plus
thanks bro
its work for me
It did not work for me, unfortunately. I removed the black part of the chip and the problem continued, just stopped blinking the led and vibrated continuously. I removed the silver part of the chip and nothing, it continued in the same way without charging. But I figured out a way to charge it, I entered the TWRP menu, (by clicking on the power button to enter the recovery it would turn off, then I pressed the button to enter the recovery, it hung up and when it was already on the twrp). At the TWRP recovery I connected the charger, and then the ZUK started charging the battery more slowly than normal, but it charged 100%. I have it for at least 2 years, I always used the original charger, only 2 or 3 months I changed the cable that broke. So I believe this is not a hardware problem, but a software problem. I use the Cardinal rom, but it seems that this happens in any rom ...
Isaías J. said:
It did not work for me, unfortunately. I removed the black part of the chip and the problem continued, just stopped blinking the led and vibrated continuously. I removed the silver part of the chip and nothing, it continued in the same way without charging. But I figured out a way to charge it, I entered the TWRP menu, (by clicking on the power button to enter the recovery it would turn off, then I pressed the button to enter the recovery, it hung up and when it was already on the twrp). At the TWRP recovery I connected the charger, and then the ZUK started charging the battery more slowly than normal, but it charged 100%. I have it for at least 2 years, I always used the original charger, only 2 or 3 months I changed the cable that broke. So I believe this is not a hardware problem, but a software problem. I use the Cardinal rom, but it seems that this happens in any rom ...
Click to expand...
Click to collapse
I am sorry for you.
I really don't know if there can be such a software problem. (have you tried clean flashing?)
Did your phone heat up a lot when charging in the usb area?
Did the procedure fix the heating?
If it charges in any way, that is not a hardware problem.
Are you using any kind of rom tweaking apps (like kernel adiutor or smartpack kernel manager) if yes check in the battery section if charging is enabled or just uninstall them.
Try flashing the stock rom.
I know it is a pain in the butt to try all of these things, especially if your zuk is your primary phone (my zuk is not my primary phone and it has a problem with flashing custom roms that i haven't fixed in months)
I didn't try the original rom, it's too bad. It also has no kernel or overclocking app. Moreover, the device did not heat up in the usb area, only in the area of the processor, when it was charging, was always like this. What made a difference before the problem was that it got too hot, especially playing pupg, which I've done a lot in the last few days, and then he hung up. He always hung up, but it was rare to happen, days before the problem he started to hang up almost every day.
But I have something new, I saw the gmail notification of your message yesterday, so today I came to respond. The device was in the TWRP menu, charging, I turned on the system and the led turned on. As I write the battery charged 10%!
JoraForever said:
I am sorry for you.
I really don't know if there can be such a software problem. (have you tried clean flashing?)
Did your phone heat up a lot when charging in the usb area?
Did the procedure fix the heating?
If it charges in any way, that is not a hardware problem.
Are you using any kind of rom tweaking apps (like kernel adiutor or smartpack kernel manager) if yes check in the battery section if charging is enabled or just uninstall them.
Try flashing the stock rom.
I know it is a pain in the butt to try all of these things, especially if your zuk is your primary phone (my zuk is not my primary phone and it has a problem with flashing custom roms that i haven't fixed in months)
Click to expand...
Click to collapse
And the problem returns.
thank you i try remove the cx chip and it work after remove it charging decreased a bit from 2100 ma to 1980 ma and volt from 4.4 to 4.1:fingers-crossed::fingers-crossed:
Working, thanks!
it worked for me! many thanks!
JoraForever said:
So my brother's zuk z2 has been broken for months now, and no repair shop could repair the phone.
I did a lot of digging and i found out that zuk z2 has a problem with quick charge 3.0 (It technically supports it but it doesn't have the necessary hardware for it)
If your zuk z2 (plus) has these symptomes this fix is guaranteed to work
Not charging.
Not turning on (Sometimes it might turn on).
Notification light blinking.
Heating in the lower part of the phone near the charging port. (If your zuk doesn't do that, then removing the cx chip will only disable fast charging)
The problem:This tiny chip with cx on it: https://i.imgur.com/YD8Eh2b.jpg
This chip is responsible for quick charge and it only supports quick charge from the original charger (that is what i was told).
When charging with an qc charger it may short out. That is where the heat is coming from.
The solution
You need to remove that chip.
You can just pry on it with a screwdriver and it pops out like its meant to do that.
Anyone can do this procedure at home, but you need a phone repair kit(<1$ online).
Or you can take your phone to the local repair guy and send them a link to this guide.
If you decide to do this by yourself i advise you to watch a teardown video, because there are some plastic tabs that you don't want to break.
1) First off, remove the sim card tray and then you need to remove the back glass, use a hair drier at the lowest setting and heat the lower part of the back of the phone (where the zuk logo is) around the perimeter.
When the glass is hot, use a suction cup to lift the glass and then use a plastic tool (only plastic tools) to slice the adhesive.
Try the suction cup method 3-4 times with heating, because the suction cup may not be strong enough to lift the glass up.
If the suction cup is not strong enough to lift the glass away, use a very thin and short piece of metal, wedge it between the glass and the plastic body (this will slightly damage the plastic) and the glass should pop out if it's hot.
Be very careful at the left upper side of the phone (the camera side) because there is the volume and power button ribbon and the battery ribbon. You don't want to damage those.
This is maybe the hardest part of this teardown.
This is how it looks like once the back cover is off: https://i.imgur.com/XGD5m7F.jpg
2) Because the chip is on the back side of the motherboard you will need to remove almost every component except the battery and some other smaller components.
Remove all screws.
Attention! one screw is under the battery ribbon.
Then try to remove the plastic.
The top plastic piece needs to be pulled from the opposite side of the back camera because there is a plastic latch near the back camera.
Pull that plastic piece up and then to the left (away from the back camera).
The lower plastic piece should be pulled from the upper most part, but it should be pulled first up and then pulled towards the top side.
If the piece doesn't move you need to remove residual adhesive or try to remove the lower plastic piece from the headphone jack side.
This is how it should look like without the plastic top cover: https://i.imgur.com/qEtXTg7.jpg
This is how it looks like without the bottom plastic piece:https://i.imgur.com/RlVhDQK.jpg
The problematic chip is in the red circle, but it is on the other side of the motherboard.
3)Unclip the connections, the antenna connectors, and the selfie camera.
By this point you should have removed the sim card tray, if not remove it NOW.
4)Remove the motherboard with the back camera (its held with some copper tape).
Inspect the charging port.
It should look something like this: https://i.imgur.com/bKiN5tG.jpg
The chip is very small.
This is how the chip looks like when removed: https://i.imgur.com/fCSJBds.jpg
This is the chip you want to remove: The one with CX on it!
This chip: https://i.imgur.com/YD8Eh2b.jpg
5)Remove the chip with something made out of metal, like a screwdriver.
6)Reassemble the phone and enjoy your charging phone.
Also this is why you would want to do it yourself.
This is what a "repair guy" did to the phone: https://i.imgur.com/5BiMn6s.jpg
He said that there was a short on the motherboard and the phone is completely dead.
The phone works, but now i don't have a power/volume button.
He obviously used a metal tool, as seen by the scratches left on the metal inside the phone.
So don't use a metal tool.
Edit: Removing this chip will only disable fast charging, if your device is perfectly working, or has different symptomes, don't remove this chip.
Edit2: The thread was broken,(only one image was showing). My dumb ass inserted the images wrongly.
Click to expand...
Click to collapse
Thank you so much for this post, I have just done this and my zuk is charging again! Thank you sir for this post! :fingers-crossed: :good:
I deleted this chip, but after that it stopped connecting to the PC. The drivers all stood, the cable was working. Then I had the urge to change the firmware to https://forum.xda-developers.com/le...rom-flyme-7-3-0-0a-zuk-z2-plus-bylzy-t3923861, but he went into the bootloop, and then probably the battery played Darth Vader in Return of the Jedi.
Removal of the chip fixed my ZUK as well!
Thank you TS!!!
I must really thank you for the guide. My phone stopped charging suddenly, tried different cables, chargers, etc and none worked. I was about to go buy a new phone and somehow stumbled on this thread. After a few days getting the courage to open the phone, i did it, followed the guide and now it is charging!!
Thank you very much!!!
Big thanks, my zuk is now working again :good:
Related
Before anyone jumps on me, I've been going through the Wiki and forums extensively, and found just one similar problem. Which wasn't solved...
My HTC TyTN/Hermes 200 won't boot up anymore. It is totally dead. I even can't get it into bootloader mode. Screen stays blank and the LED is off.
Put the (3 months old) battery in another Hermes to test it, and it's at 100% charge.
My Hermes shows a steady red LED when it's plugged into power without the battery in, and no LED at all when the battery is installed. The red LED turns off when the battery is installed while there's power going into the unit.
I've left the battery out for at least an hour, plugged it back in, same results. Like the other guy I tried the "pull power, pull battery, plug in power, plug in battery, reset" trick http://forum.xda-developers.com/show...6469&p=1077622 - to no avail.
Does anyone have any last resort ideas on how to get it to at least come back up to a boot loader screen ?
check the battery contact points on the phone. the hermes shows a red led when its plugged in but without a battery
... have you ever dismantled your hermes? your screen ribbon cable may have dead tracks or not be connected properly
just a test on the opposite side of the battery connectors with battery removed press firmly without putting pressure on the LCD, this worked for me when i had a white screen on power up.
if this fixes the problem you may need to actually dismantle the back and put some flame retardant electrical tape on the back over the existing tape to add an extra layer of pressure and retension
XtreMe_G said:
check the battery contact points on the phone. the hermes shows a red led when its plugged in but without a battery
Click to expand...
Click to collapse
Yes, I have cleaned the contact too, nothing. And the battery is OK for sure, my colleague's TyTN runs on it without any problem.
Mattnokis said:
... have you ever dismantled your hermes? your screen ribbon cable may have dead tracks or not be connected
Click to expand...
Click to collapse
In fact I have, I have totally dismantled and reassembled my TyTN yesterday afternoon, nothing.
the only other problem may be that when being dismantled you may have damaged some sensitive components, Electro Static Discharge will fry sensitive CMOS components, they do not like it at all, whenever dismantling you should wear an earth strap, any time i dismantled mine it was on a workbench with a static mat and i was earthed through the mat.
but this is one possibility, the only other idea is to swap main board and displays with another that works, finding someone willing to allow you to do this with a working hemes is the tough part.
thats as much all i can think of for now
R.I.P. my trustful Hermes 200
Thanks all for your assistance. I have come to the conclusion that my sweetheart is no longer among us. May she rest in peace.
I have obtained a (2d hand) replacement yesterday. May this one last longer.
I'll keep the old TyTN for replacement parts.
Oh well...
hello,
I got an hd2 with a cracked screen off ebay and after much time ands effort have succefully fixed. The problem now is that the battery terminal is broken.. or I think it is..
When i have the housing off and hold the battery on with my hand it turns on. When i put the housing on, and put the battery in it doesn't turn on
a few times when i shoved a piece of paper so that the battery would get tighter agianst the terminal, it would turn on, so i figured that i must be the terminal that was broken, so i straigtened the pins out, i thought that would fix the problem, but no. this actually made it worse.. sometimes it turns on sometimes it doesnt, even when the housing's off. I think that the terminal is broken
My question is.
would i be able to solder a wire directly to the contact where the battery terminal is soldered on to the motherboard, so i could connect that wire to the battery.
or would i be able to find a replacement connector somewhere?
I don't know if this is the right section, anyway because it isn't specifically hardware related I posted here... for admins feel free to move in the appropriate thread.
My G2 dropped on the floor and as result I got a complete broken display plus not working touch.
The device, touch apart, worked without issues so as 1st step I made a full backup of sd-like content (music, pictures, etc...) to my laptop.
note: even if touch didn't work I was able to access the device trough adb and a very useful utility (http://marian.schedenig.name/2014/07/03/remote-control-your-android-phone-through-adb/)
Next I ordered a replacement for the display, looked for instructions and changed by myself... and the phone didn't boot or even charge... nothing, the only signal of life was when attached to the wall charger the led blinking in red eight (8) times consecutively then no blink for a second and again blink for 8 times and so on in an infinite loop.
Of course I started to look for solution and tried every kind of combination but none worked.
I started to think that I missed up something during the display replacement or the battery fault or even I fried in some way the motherboard, anyway for what I read it supposed that could be that the battery gone under certain voltage or minimal charge so the motherboard circuit didn't recognize as "good or safe battery", it is simply bypassed by charge circuit.
note: I waited for the new display about 10 days and the device (fully charged) slept (turned off) in a drawer so I don't think it was totally discharged
I disassembled and reassembled again the device but nothing happened so while looking for a solution I saw a video on Youtube (https://www.youtube.com/watch?v=MZwknmWCmOE) solving a issue similar to mine so as instructions I took an old charger (800ma), cut the charger connector and exposed the 2 internal wires (one red and the other gray/black).
Then I opened the device, disconnected the battery and attached directly into the battery connector the two charger wires (in this way mobile motherboard is bypassed).
I used a small piece of tape to stop and make touch laterally the 2 wires to the connector, something like: dark wire -> [ battery connector] <- red wire
Keep in mind that the connector is something very small like (0) where left parenthesis is for dark wire and right parenthesis for the red one.
note: you can't wrong with wires, because the positive (on the battery connector) has a small white triangle.
Of course I found a way to don't move/mess wires before connecting the wall charger... I put another piece of tape at 20cm on the table to keep the cable charger fixed near the phone, then I attached the wall charger...
remember: attach the charger to the wall ONLY when you have finished to place/fix the contacts!
Waited just 1 minute because exposed charger wires was very close and didn't want to fry something... but it was enough!!
Reconnected the battery and voilà the phone turned on!
The phone turned on with almost 80% of charge, all seemed to work... except that I found 2 issues... I suppose because the case didn't match perfectly anymore (I opened the device 4 times and disassembled-reassembled twice)
1st speaker didn't work, so I reopened the device and checked the speaker connector, I discovered that the speaker didn't touch very well so I put a small stripe of tape under the connector (the small vertical green stripe in the lower side of the phone) to lift it and making touch stronger with the speaker module (the black part the come out), here on Youtube for reference: https://www.youtube.com/watch?v=XE2FPmFUrQQ
2nd GPS didn't work very well (discovered after a couple of days) so I reopened the device and applied this solution that worked perfectly: https://www.youtube.com/watch?v=dfS4LpfcLfg
This is my story in the hope to help someone, if you have apparently a total dead phone and the only signal of life is a 8 times blinking red light... now you know what to do!
Regards,
Davide
Thank u for share your story
Congrats on fixing your problem!
suiller said:
The phone turned on with almost 80% of charge, all seemed to work... except that I found 2 issues... I suppose because the case didn't match perfectly anymore (I opened the device 4 times and disassembled-reassembled twice)
Click to expand...
Click to collapse
You mentioned the alignment of the phone wasn't the same as before....
Did your battery swell or change shape at all during this process?
If so could be a sign its on its way out and needs replacement.
A dying G2 lithium ion battery changes physical shape and completely alters the internal alignment of your components.
May be worth an extra 10.00 to replace your battery at this point with a new one
tiguy99 said:
Congrats on fixing your problem!
Click to expand...
Click to collapse
thank you, I was a bit frustrated because I thought to have broken the motherboard, even if it wasn't very easy I didn't surrend and I won!
tiguy99 said:
You mentioned the alignment of the phone wasn't the same as before....
Did your battery swell or change shape at all during this process?
Click to expand...
Click to collapse
I understand what you mean but no I don't think so... it seemed the same size
anyway battery has less than 1 year of life and never showed symptoms or bad behavior, right now is running as before... I can pass easily 24h without recharge
suiller said:
thank you, I was a bit frustrated because I thought to have broken the motherboard, even if it wasn't very easy I didn't surrend and I won!
I understand what you mean but no I don't think so... it seemed the same size
anyway battery has less than 1 year of life and never showed symptoms or bad behavior, right now is running as before... I can pass easily 24h without recharge
Click to expand...
Click to collapse
Sounds good!
Have you found the source of your alignment being off?
tiguy99 said:
Have you found the source of your alignment being off?
Click to expand...
Click to collapse
I checked and found nothing in particular... just a bit near the sim "area", but it seems just a sort of plastic adaptation... as mentioned before I opened, disassembled, reassembled and then closed it 4-5 times (in just few days)
I cannot turn on my LG G2 after putting a new battery in it that I bought of LG.
I have tried to hold the vol down and power button together will plugging into power source but to no avail.I have held just the power button while plugging into power but to no avail.
Any help would be much appreciated.
Try to carefully check the electric contacts: re-open the case and press enough all the electrical connectors. I solved this way...
There may also be a chance of damaged battery (it is hard to find an original one): in this case you have to ask for replacement.
MotoGix said:
Try to carefully check the electric contacts: re-open the case and press enough all the electrical connectors. I solved this way...
There may also be a chance of damaged battery (it is hard to find an original one): in this case you have to ask for replacement.
Click to expand...
Click to collapse
I have checked all the connectors umpteen times and they all click into place.
I got the battery from LG so it is a genuine LG battery has stated in my post.
I had same problem with my Optimus G
I change the battery last year with a battery I bought off Ebay without any problems.I then found out the battery was not genuine (not holding its charge) and I bought a battery from LG.When I replaced the battery I bought off Ebay with the battery I bought from LG my G2 would not turn on.
Is there a tool which I could use to test my G2 phone (download a tool/app)?
Could it be an hardware issue?
Shlong7 said:
I change the battery last year with a battery I bought off Ebay without any problems.I then found out the battery was not genuine (not holding its charge) and I bought a battery from LG.When I replaced the battery I bought off Ebay with the battery I bought from LG my G2 would not turn on.
Is there a tool which I could use to test my G2 phone (download a tool/app)?
Could it be an hardware issue?
Click to expand...
Click to collapse
I bought the battery on ebay, since I don't have access to any LG store.
After a first failed attempt, I removed and reinserted the battery and the phone turned on. I attributed the issue to an electric contact but my assumption could be wrong and there were likely other reasons...
Unfortunately, I am not able to suggest to you any workaround. You may ask directly to LG, where you bought the battery...
There is a hidden menu (3845#*802#) for testing battery and charge efficiency, but phone must be turned on, then you have to use the old battery.
Anyway, I don't think it is an hardware issue.
I bought another battery off eBay to see if it was the battery but the phone still won't turn on.
It sounds not good... Are some electrical contact pins of the phone possibly damaged or dirty?
MotoGix said:
It sounds not good... Are some electrical contact pins of the phone possibly damaged or dirty?
Click to expand...
Click to collapse
No,they look alright.
I did press the power button on the phone before I put the white camera cover on and the main white phone cover on.
So much the better!
What possible think could I have damaged?
Shlong7 said:
What possible think could I have damaged?
Click to expand...
Click to collapse
Sorry, I understood you solved the problem (misunderstanding due to my poor English).
Look carefully at all the pins of the connectors (screen, motherboard, etc.): Are they alright or bent over?
If they are bent over you can try to straighten them with an electronic nipper.
On the contrary, if they are OK, my advice is to go to the LG service center (for example where you bought the new original battery) and ask them to check the phone hardware. Perhaps it is just a stupid issue, easy to solve. It is still a great phone, even though it is 5 five years old, and it's worth it. It is even faster of my most recent Motorola X Play...
Unfortunately, I have not enough experience with this phone, so I can't help you anymore: I own it since few weeks only, because it is my wife old phone. I was just lucky in substituting battery with negligeble issues!
I have looked at all the pins on each connector and they look all in line.
May I have damaged the charging ribbons when I pressed the power button before I put the camera cover and the phone cover back on.
I have noticed the black tape on the camera cover (https://www.ebay.co.uk/itm/LG-G2-Ca...368363?hash=item2833f4ba6b:g:FWsAAOSwIaFZFH5k) is damaged,could this cause my G2 to not turn on?
Shlong7 said:
I have looked at all the pins on each connector and the look all in line.
May I have damaged the charging ribbons when I pressed the power button before I put the camera cover and the phone cover back on.
I have noticed the black tape on the camera cover (https://www.ebay.co.uk/itm/LG-G2-Ca...68363?hash=item2833f4ba6b:g:FWsAAOSwIaFZFH5k) is damaged,could this cause my G" to not turn on?
Click to expand...
Click to collapse
I don't think so: the power button acts on a switch; you can press on the switch in many other ways, with the same results...
Check instead the electric contact on the camera cover (see 2nd image of the camera cover, top-left of the above link): it is a sort of electrical bridge (closes the circuit). You may verify if it works right by means of a multimeter (null resistance).
MotoGix said:
I don't think so: the power button acts on a switch; you can press on the switch in many other ways, with the same results...
Check instead the electric contact on the camera cover (see 2nd image of the camera cover, top-left of the above link): it is a sort of electrical bridge (closes the circuit). You may verify if it works right by means of a multimeter (null resistance).
Click to expand...
Click to collapse
Im not good at using multi-meters.
What should I set the range of the multi-meter when testing the electrical bridge on the camera cover?
What should the multi-meter read when testing the electrical bridge to see if it works?
You should simply get zero resistance. Multimeters are easy to use: at first, select to measure resistance, by setting the highest sensitivity (the smallest full-scale), then measure the resistance. There are many tutorial on YouTube.
Please, consider it is possible this is not the problem!
Anyway, I'd suggest you warmly to send the phone at the service centre.
Sent from my LG-D802 using XDA Labs
Yes,I do get zero resistance when testing the electrical bridge on the camera cover.
It will cost alot to have it repaired at the service centre,probably not worth having my G2 repaired bc the battery cost me £40.
You're right, it might not be worth it.
Before throwing away the phone, try to ask where you bought the battery. Perhaps they will find a solution for you.
Another phone with similar specs costs more than 300£, for sure; moreover, most of phones have the cover in glass or alluminium and are more delicate than G2...
Sent from my LG-D802 using XDA Labs
I have been in touch with LG where I bought the battery from and they said the repair would cost more than I paid for the phone,which I predicted.
I don't think the battery is faulty (I bought another battery of eBay and the phone still won't turn on),unless the eBay battery is faulty too.
Could I have damaged the power switch if I pulled out the power switch connector while the battery was connected?
I am so sorry.
But, just for curiosity, what is the damage?
I just replaced the battery and screen on my LeEco Le Max 2, and this post will detail the process. Hopefully it will be helpful for someone who is considering to replace their screen and/or battery.
Consider buying an extra screen
There are a number of people who have reported breaking their screen as a result of replacing the battery. I highly recommend that you buy a replacement screen if you intend to replace the battery. Unfortunately while removing my screen I also created a few dead pixels (which you'll see later). With all that being said, it is definitely possible to remove your screen without damaging it. I suspect that next time I will be able to remove the screen without damaging it.
Tools required
- small philips screwdriver (from Jeweler's kit)
- thin prying tools
- suction cup that tightly grips screen (you'll see the one I used later)
- heat gun or hair dryer
Onto the replacement procedure
Before you begin, make sure that you have plenty of time to commit to the replacement. It took me about 2 hours to swap the battery and screen. You should also read this full post before attempting to remove your battery.
Remove any sim cards in your phone and turn your phone off.
You'll need to heat up the perimeter of the screen on your phone. This can be done using a heat gun, however I manged this using a hair dryer. I spent about 10 minutes heating up the screen before attempting to remove the screen. Note that as you're removing the screen you may need reheat certain areas of the screen to loosen up the adhesive that secures the screen.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Next you'll want to apply the suction cup towards the bottom of the screen. Ensure that you have a solid grip on the screen.
I pulled the suction cup away from the screen, and began to notice that the sides of the screen were begging to come undone. I used a prying tool to sliced the adhesive that was holding the screen in place.
Go around the edge of the screen very carefully until the entire screen is removed. Remember the screen is glass and will break if it's flexed too much. My advice would be to go slow and use a lot of heat.
You'll need to remove two small screws behind the screen in order to disconnect the cable which connects the screen to the body of the phone.
Then disconnect the screen ribbon from the phone.
There will be an additional 15 screws which you'll need to remove in order to get to the battery. If you are just replacing the screen you can skip ahead to the section where I connect the new screen to the phone.
With all of the screws removed, you can pry the shield away from the back of the phone. You'll need to be careful, as a ribbon is glued to the back of the shield.
You can see the glue locations for the ribbon on the back of the shield. With the shield removed, you can now finally access the old battery.
Disconnect the ribbon that is right above the battery. Near this large ribbon will be another smaller ribbon that connects the battery to your phone. Disconnect the battery from the phone.
Now you can begin to remove the battery.
Important note from an XDA user
Jaki1122 said:
In the attach photos, you can see on the glue band (or whatever is called) a wider zone close to the motherboard. That is because you are supposed to grab that and pull straight. Then the glue comes off and the battery pops off nicely without being bend and with 0 danger. For this procedure you need to take out the motherboard entirely, which is pretty easy and quick. Take out the SIM tray (I always forget about this one ), disconnect the few connectors (vol and power buttons, fingerprint, USB Dock and the coaxial cable on the right), then 2 screws and its just comes out. After this the end of the glue band is clearly visible and easy to take and pull. Also, and this applies to all phones, you can use isopropyl 99% to weaken the glue (also useful for cleaning PCBs and fix water damage). Another note: you should always avoid bending a Lithium battery like in the photos, heat it to 70 degrees Celsius to weaken the glue and take it out as straight as possible.
Note 2: FOR LE ECO LE 2 USERS: The battery is mounted exactly like the Max 2, BUT you need to take out the USB PCB and speaker on the lower part of the phone instead of the motherboard, given that there is where the "puller" is. Why is it different to the Max 2 if the rest of the phone is identical? No idea... Maybe a brainfart?
Click to expand...
Click to collapse
Be very careful not to puncture the battery as you remove the battery. The battery is glued into the base of the phone. You can see the two major glue strips in the following picture.
Place and secure the replacement battery.
Reassemble your phone. Before you put the new screen on, I recommend testing the original screen to see if you damaged the screen during the process.
You can see a few new dead pixels on my original screen. This happened as I was prying the screen open, so you'll want to be very careful as you remove the screen. Do not stick your prying tool too far in or against the screen. This damage is something I could live with, however since I have a new screen I'll go ahead and put it on. Turn your phone off before attaching a different screen.
You'll want to connect and test the new screen before proceeding.
Hopefully your new screen is working. Turn your phone off again. Now you should do your best to remove the old adhesive that was used to secure the old screen to the phone. However, you should only do this if you have new adhesive to secure the screen in place!
Your new screen should come with an adhesive template. Remove the outer edge of this template which will be placed on your phone's body.
Now place the adhesive template onto the body of the phone. You'll have to push down such that the adhesive has been firmly placed. Remove the template such that only the adhesive around the perimeter of your phone remains.
Connect the new screen's ribbon to the phone, and secure with the two screws. You can now firmly place the new screen into the phone. You'll want to firmly press the screen into place around the edges.
You'll want to keep pressure on the screen while the adhesive sets in place. I used a few pennies placed on the floor to give clearance to the rear camera. Then I placed the phone on the pennies, and heated up the screen again. I believe the adhesive will cure faster and stronger onces it's been warmed up.
I then placed a textbook onto the screen with a 10 pound weight, where I let the phone sit for an hour or so.
Enjoy your newly replaced battery/screen and hopefully this has been helpful!
AccuBattery stats for the new battery
I'm now on the second charge of the battery, and I figured you may be interested in some of the stats of the battery. You can see that despite the battery being labeled 4100 mAH, the estimated battery capacity is only about 3000 mAH.
Frequently Asked Questions
coming soon
Edit June 7, 2019, I think we can conclude that changing the battery capacity as detailed below doesn't do anything
Updating battery capacity in Lineage based roms
This is in regards to this post https://forum.xda-developers.com/galaxy-s3/general/fix-compiled-powerprofile-xml-file-to-t1732722
I don't think that updating the power_profile.xml https://github.com/LineageOS/androi...works/base/core/res/res/xml/power_profile.xml does anything really. However if you want to change it to a new battery capacity, this post will explain how.
I edited the default power_profile.xml to reflect the new 4100 mAH battery (there are many doubts of the real battery capacity). I then compiled the power_profile.xml. The attached power_profile.xml is the compiled version.
1. Boot into recovery and copy /system/framework/framework-res.apk over to your computer.
2. Make a backup of this framework-res.apk
3. Open framework-res.apk on your computer using 7zip.
4. Navigate to res/xml/
5. Delete the power_profile.xml
6. Copy the attached power_profile.xml into the location where the previous power_profile.xml file was. Note this is a compiled file, meaning that it is not in plain text and you can't read the inside of the file.
7. save the framework-res.apk
8. Copy the new framework-res.apk over to /system/framework/
9. Reboot your phone.
You can use the following command to pull a csv of your battery stats while your phone is connected to your computer and running lineage (other other OS). More info here https://developer.android.com/studio/command-line/dumpsys
Code:
adb shell dumpsys batterystats --checkin > bat.csv
which will create a comma separated list of your battery properties. The one related to the specified capacity of your battery has the section identifier pws. Open bat.csv on your computer and search for pws. Before doing this change it would show up as 3100, and now it shows up as 4100. However, I have not noticed that this did anything different with the battery behavior or estimated battery capacity. The only thing this appeared to do is now that when I open AccuBattery a different manufacture capacity shows up.
Six month battery review:
I have 120 charge sessions, and probably only 1% of those used Quick Charge 3.0. AccuBattery shows estimated capacity of 3,065 mAh. The battery has been strong so far. See attached screenshots.
Hi, great guide, but when i try to download the power_profile.xml you uploaded i get an error.
I'm thinking on buying a new battery to replace it (and buy a screen just in case) because my current one its not calibrated and i cannot find a way to calibrate it, it says that its got 1800mah but it can actually hold 3000+.., the real capacity its really 3000-? i have seen people that say its around 3800~ can you confirm?
Links to buy???
sameer 100 said:
Links to buy???
Click to expand...
Click to collapse
These are the products that I purchased and the price that I paid. I don't necessary endorse these products... besides the suction cup. That one was great. One more thing, the adaptive brightness on the new screen doesn't appear to work as good it with the original screen.
Screen $13.17: https://www.aliexpress.com/item/ori...-X820-touch-screen-Digitizer/32862597681.html
Battery $10.81: https://www.aliexpress.com/item/HSA...-2-X820-Le-Max2-5-7inch-X821/32875310678.html
Tools $11.88: https://www.aliexpress.com/item/Jel...Set-LCD-Screen-Opening-Plier/32831437976.html
Suction cup $1.36: https://www.aliexpress.com/item/Bod...ss-Metal-Cell-Phone-Table-PC/32843015681.html
hitagisenjougahara said:
Hi, great guide, but when i try to download the power_profile.xml you uploaded i get an error.
I'm thinking on buying a new battery to replace it (and buy a screen just in case) because my current one its not calibrated and i cannot find a way to calibrate it, it says that its got 1800mah but it can actually hold 3000+.., the real capacity its really 3000-? i have seen people that say its around 3800~ can you confirm?
Click to expand...
Click to collapse
Try right clicking power_profile.xml and doing a save as. That just worked for me.
If it's a software bug, then EUI should help.
I was in a similar situation where my phone was 1.5 years old, and my estimated battery capacity was around 1700 mAH. I tried calibrating my battery (on lineage), and it did not work. As soon as I put this battery in, on the very first charge, the calibration appeared correctly on lineage. No sudden battery % drops or other weird behavior.
xlcashlx said:
These are the products that I purchased and the price that I paid. I don't necessary endorse these products... besides the suction cup. That one was great. One more thing, the adaptive brightness on the new screen doesn't appear to work as good it with the original screen.
Screen $13.17: https://www.aliexpress.com/item/ori...-X820-touch-screen-Digitizer/32862597681.html
Battery $10.81: https://www.aliexpress.com/item/HSA...-2-X820-Le-Max2-5-7inch-X821/32875310678.html
Tools $11.88: https://www.aliexpress.com/item/Jel...Set-LCD-Screen-Opening-Plier/32831437976.html
Suction cup $1.36: https://www.aliexpress.com/item/Bod...ss-Metal-Cell-Phone-Table-PC/32843015681.html
Try right clicking power_profile.xml and doing a save as. That just worked for me.
If it's a software bug, then EUI should help.
I was in a similar situation where my phone was 1.5 years old, and my estimated battery capacity was around 1700 mAH. I tried calibrating my battery (on lineage), and it did not work. As soon as I put this battery in, on the very first charge, the calibration appeared correctly on lineage. No sudden battery % drops or other weird behavior.
Click to expand...
Click to collapse
Did you fixed that problem? Or your battery was actually 1700mah? Because mine is not..
Also any updates in the real battery capacity? I've thinking on changing the battery right away, but if its only 3000mah its not worth, whats the charge current when it reaches 100%? it should say that in accubattery
hitagisenjougahara said:
Did you fixed that problem? Or your battery was actually 1700mah? Because mine is not..
Also any updates in the real battery capacity? I've thinking on changing the battery right away, but if its only 3000mah its not worth, whats the charge current when it reaches 100%? it should say that in accubattery
Click to expand...
Click to collapse
My battery was failing and rapidly getting worse. The capacity I was getting was actually 1700 mAH.
You can see the current hit zero and the capacity is still around 3100 mAH. I did a 1% to 99% uninterrupted charge in EUI. It would have been nice if the battery was actually 4100 mAH, but it does not appear that is the case.
xlcashlx said:
My battery was failing and rapidly getting worse. The capacity I was getting was actually 1700 mAH and was rapidly getting worse.
You can see the current hit zero and the capacity is still around 3100 mAH. I did a 1% to 99% uninterrupted charge in EUI. It would have been nice if the battery was actually 4100 mAH, but it does not appear that is the case.
Click to expand...
Click to collapse
Feelsbad, well its better than 1700 anyways, thanks for sharing
Hi bro, i heard from a guy that has recently replaced the battery to this HSABAT one that all OREO & Nougat roms are capped at 3100mah and you need to use another rom (this: https://t.me/LeitaEUI6) to get the full capacity of the battery, he says its real battery capacity its around 3800~ mah, will be cool if you try this rom and share results
hitagisenjougahara said:
Hi bro, i heard from a guy that has recently replaced the battery to this HSABAT one that all OREO & Nougat roms are capped at 3100mah and you need to use another rom (this: https://t.me/LeitaEUI6) to get the full capacity of the battery, he says its real battery capacity its around 3800~ mah, will be cool if you try this rom and share results
Click to expand...
Click to collapse
That would be cool.
Can I use any EUI6 build? I did try EUI5 and the capacity was still arround 3100 =/
xlcashlx said:
That would be cool.
Can I use any EUI6 build? I did try EUI5 and the capacity was still arround 3100 =/
Click to expand...
Click to collapse
I dont know, try the one i sent
Hey,
fist, thanks for that great guide!
I also changed my battery, but the capacity is only 3000 mAh. It is better than the old battery, but not 4100 mAh. I did the thing with the xml file. But nothing changed. I have lineageos pie.
I think there are more mechanisms which will decrease the capacity.
I think it will be the battery_cycles. If the cycles are high, the batteryvoltage will be cut. If I charge, the battery isn't at 4.4 volts.
I found this files to change the cycles and the capacity. But it is just temporary:
/sys/Classic/power-supply/battery/
If I write in these files, at the next start it will be changed...
Is there any solution for the shutoff voltage and charge voltage?
Thanks.
Excellent work!
This phone is mercifully reparable once the screen is off. My advice to people is to take that part very carefully and deliberately, it's about the only thing you'll break if you're careless. Once it's off, things become much easier.
Publishing information like this is very helpful to those who would attempt repairs of a solid phone, and it's a gift to the community.
Did someone remove the screen without breaking it? Maybe with a small peace of plastic sheet instead metal prying tool .
Huncriter said:
Did someone remove the screen without breaking it? Maybe with a small peace of plastic sheet instead metal prying tool .
Click to expand...
Click to collapse
Those few dead pixels were the only damage to my screen, and it's damage I could have lived with. After this experience, I probably could have removed the screen without damage. This was the first smartphone with this design that I've ever opened.
I think this YT video shows someone removing a Le 2 screen without breaking it. https://www.youtube.com/watch?v=f_LExkf89z0 Be warned the fingernail thing you'll see grosses me out.
That said, there are numerous comments on XDA about people breaking their screen while attempting to replace their battery. It's highly recommended that you buy a replacement screen, especially if the lead (shipping + order) time is long for your country.
Thanks
Ths
Important extra info on the repair!!!
I've changed countless screens on this (and other) phones, and there is something VERY important missing on this tutorial (very well done apart from what I'm about to explain).
In the attach photos, (the same as in the OP post) you can see on the glue band (or whatever is called) a wider zone close to the motherboard. That is because you are supposed to grab that and pull straight. Then the glue comes off and the battery pops off nicely without being bend and with 0 danger. For this procedure you need to take out the motherboard entirely, which is pretty easy and quick. Take out the SIM tray (I always forget about this one ), disconnect the few connectors (vol and power buttons, fingerprint, USB Dock and the coaxial cable on the right), then 2 screws and its just comes out. After this the end of the glue band is clearly visible and easy to take and pull. Also, and this applies to all phones, you can use isopropyl 99% to weaken the glue (also useful for cleaning PCBs and fix water damage). Another note: you should always avoid bending a Lithium battery like in the photos, heat it to 70 degrees Celsius to weaken the glue and take it out as straight as possible.
Just as a note, I'm just trying to help here, not criticising other people's very appreciated apportions, just complementing them when I can.
Note 2: FOR LE ECO LE 2 USERS: The battery is mounted exactly like the Max 2, BUT you need to take out the USB PCB and speaker on the lower part of the phone instead of the motherboard, given that there is where the "puller" is. Why is it different to the Max 2 if the rest of the phone is identical? No idea... Maybe a brainfart?
3000 mAh to 4100 mAh
xlcashlx said:
I just replaced the battery and screen on my LeEco Le Max 2, and this post will detail the process. Hopefully it will be helpful for someone who is considering to replace their screen and/or battery.
Consider buying an extra screen
There are a number of people who have reported breaking their screen as a result of replacing the battery. I highly recommend that you buy a replacement screen if you intend to replace the battery. Unfortunately while removing my screen I also created a few dead pixels (which you'll see later). With all that being said, it is definitely possible to remove your screen without damaging it. I suspect that next time I will be able to remove the screen without damaging it.
Tools required
- small philips screwdriver (from Jeweler's kit)
- thin prying tools
- suction cup that tightly grips screen (you'll see the one I used later)
- heat gun or hair dryer
Onto the replacement procedure
Before you begin, make sure that you have plenty of time to commit to the replacement. It took me about 2 hours to swap the battery and screen. You should also read this full post before attempting to remove your battery.
Remove any sim cards in your phone and turn your phone off.
You'll need to heat up the perimeter of the screen on your phone. This can be done using a heat gun, however I manged this using a hair dryer. I spent about 10 minutes heating up the screen before attempting to remove the screen. Note that as you're removing the screen you may need reheat certain areas of the screen to loosen up the adhesive that secures the screen.
Next you'll want to apply the suction cup towards the bottom of the screen. Ensure that you have a solid grip on the screen.
I pulled the suction cup away from the screen, and began to notice that the sides of the screen were begging to come undone. I used a prying tool to sliced the adhesive that was holding the screen in place.
Go around the edge of the screen very carefully until the entire screen is removed. Remember the screen is glass and will break if it's flexed too much. My advice would be to go slow and use a lot of heat.
You'll need to remove two small screws behind the screen in order to disconnect the cable which connects the screen to the body of the phone.
Then disconnect the screen ribbon from the phone.
There will be an additional 15 screws which you'll need to remove in order to get to the battery. If you are just replacing the screen you can skip ahead to the section where I connect the new screen to the phone.
With all of the screws removed, you can pry the shield away from the back of the phone. You'll need to be careful, as a ribbon is glued to the back of the shield.
You can see the glue locations for the ribbon on the back of the shield. With the shield removed, you can now finally access the old battery.
Disconnect the ribbon that is right above the battery. Near this large ribbon will be another smaller ribbon that connects the battery to your phone. Disconnect the battery from the phone.
Now you can begin to remove the battery.
Important note from an XDA user
Be very careful not to puncture the battery as you remove the battery. The battery is glued into the base of the phone. You can see the two major glue strips in the following picture.
Place and secure the replacement battery.
Reassemble your phone. Before you put the new screen on, I recommend testing the original screen to see if you damaged the screen during the process.
You can see a few new dead pixels on my original screen. This happened as I was prying the screen open, so you'll want to be very careful as you remove the screen. Do not stick your prying tool too far in or against the screen. This damage is something I could live with, however since I have a new screen I'll go ahead and put it on. Turn your phone off before attaching a different screen.
You'll want to connect and test the new screen before proceeding.
Hopefully your new screen is working. Turn your phone off again. Now you should do your best to remove the old adhesive that was used to secure the old screen to the phone. However, you should only do this if you have new adhesive to secure the screen in place!
Your new screen should come with an adhesive template. Remove the outer edge of this template which will be placed on your phone's body.
Now place the adhesive template onto the body of the phone. You'll have to push down such that the adhesive has been firmly placed. Remove the template such that only the adhesive around the perimeter of your phone remains.
Connect the new screen's ribbon to the phone, and secure with the two screws. You can now firmly place the new screen into the phone. You'll want to firmly press the screen into place around the edges.
You'll want to keep pressure on the screen while the adhesive sets in place. I used a few pennies placed on the floor to give clearance to the rear camera. Then I placed the phone on the pennies, and heated up the screen again. I believe the adhesive will cure faster and stronger onces it's been warmed up.
I then placed a textbook onto the screen with a 10 pound weight, where I let the phone sit for an hour or so.
Enjoy your newly replaced battery/screen and hopefully this has been helpful!
AccuBattery stats for the new battery
I'm now on the second charge of the battery, and I figured you may be interested in some of the stats of the battery. You can see that despite the battery being labeled 4100 mAH, the estimated battery capacity is only about 3000 mAH.
Click to expand...
Click to collapse
Can I install 4100mAh battery to my le2? 3000 is not enough
Are you kidding ? You unnecessary quote an entire post asking a question you could have answered yourself just by reading the thread ? Unbelievable.