Database Users

[Q] Camera lens scratched

Camera lens or cover scratched. Camera app now unable to focus, or lock on. Constantly trying to focus. Anyone have suggestions on repairing the lens myself or send it in for repair. It been rooted.
I have seen replacement parts, but unsure what piece holds the lens cover.
txs
M

My dad used to get scratches out of his watch glass by rubbing it with brasso and a soft cloth, you could try that first ?
Sent from my LG-D802 using Tapatalk

[GUIDE] Rear glass replacement

So recently I cracked the rear glass on my Pixel 2 XL. After searching around, I found the "official"repair places wanted around $80 to replace this. Then I found eBay had replacement glass for $13 (in the US, cheaper from China), and decided to give it a try. Figured worse case scenario I end up at the repair place getting the glass replaced anyway, and I'm out $13 extra.
This was not a difficult process necessarily, what I will say is that the glass used is extremely thin (stock and aftermarket), and the process of removing the old glass is likely to produce many tiny glass fragments.
Here's how I did it, if anyone is interested in giving this a try:
1. Mis en place. I used a couple plastic and nylon spudgers, guitar picks, one metal spudger, a hair dryer, and packing tape. I did this repair in the bathroom near the sink so I could easily brush small glass pieces into the sink and wash them down the drain.
2. Start off by heating up the rear glass with the hair dryer, but not too hot. You need to be able to hold the phone afterall. Take a piece of packing tape and place it over the rear glass to somewhat keep it together.
3. I used the thin metal spudger to get started on one side of the glass. I started on the broken side as I already had a gap there to work with. Slowly go around and remove the glass and double sided tape from the rear frame.
3. Remove the camera lens cover from the glass. It's attached to the glass with double sided tape. Most likely going to be small chunks of glass stuck to the front of the lens assembly.
4. Clean up any leftover glue/double sided tape and chunks of glass, so you have a nice clean surface to stick the new glass to.
5. Install the lens cover on the replacement glass, and clean the inside and outside of the lens cover and inspect the camera assembly itself for chunks of glass/dust/etc.
6. Install the new glass (with lens cover now attached) to the back of your Pixel 2 XL. Be very careful to line it up exactly where you want it to sit before dropping it onto the frame of the phone (you likely will not be able to peel it off and reapply it if you mess up, as the glass is very thin and would probably shatter if you try to remove it).
7. Profit.
That's about it. All in all this took me about 30 minutes from start to finish, and saved me just over $60. Worth it for a cheapskate like me ?
Hope this helps someone.

Excellent write up, and the great photos!
Thanks for posting

Superusefull!! Thank so much!

do you feel like this compromised the water resistance part of the phone?

im pretty sure the waterproof feature is gone

jyn1989 said:
im pretty sure the waterproof feature is gone
Click to expand...
Click to collapse
It has never been waterproof.
Sent from my Pixel 2 XL using Tapatalk

Hello everyone,
I've broken lil bit the glass and considering replacement. But don't want to lose waterprofness. What do you think about this statement:
"The glass back of the Pixel 2 is purely decorative, and the Pixel 2 will still be waterproof with a broken glass back.
Why? As can be seen in the teardown video at https://youtu.be/Zq7nyzldgr4 at 4:14, the back cover of the Pixel 2 goes underneath the glass. Also, it looks like replacing the glass back would not require a teardown, since there seem to be no screws holding the glass in place from the inside. I suspect the glass back is merely glued on or clipped in."
For me it sounds reasonable that waterprofness might still be there after replacement. Attaching screenshot of mentioned back cover which is going under the glass.
Thanks for your opinion!

Pixel 2 is waterproof
Pixel 2 is IP67 rated meaning it's good for up to a metre depth of water, hence it being waterproof but if anyone was wondering even if you do break the back glass as I have it's purely cosmetic as there is some pretty strong plastic and glue behind it keeping the waterproof feature in place

How do you fix it to be waterproof like factory?
|Use waterproof glue around camera lens and LED lens or is there a adhesive to buy?

buying a g6 with broken camera glass...

Getting it for 200aud..
Can replace the glass piece for about 10 off eBay.
My question is how tight that area is in general in terms of the ip68 rating, consisting that the "glass" is just an adhesive. I.e. is the rating still intact

jewnersey said:
Getting it for 200aud..
Can replace the glass piece for about 10 off eBay.
My question is how tight that area is in general in terms of the ip68 rating, consisting that the "glass" is just an adhesive. I.e. is the rating still intact
Click to expand...
Click to collapse
if you only replace the glass from the camera and if you replace it with the ORIGINAL part, then you will have the IP rating the same way, BUT...if you buy cheap glass with cheap adhesive...i didnt know how it takes the IP at same level, and how long it will take to lose the glue and maybe crack again.
Better safe than sorrow...
see this: https://www.youtube.com/watch?v=6qfQ1TH_KBs

It's very tight. I bought one for a 3rd the price of new the glue was discolored, but the glass was otherwise ok.
Love Jerry's Videos. But he'd already removed that lens, and had an appropriate crack to help leverage up a piece of the glass. I couldn't even get a scalpel blade under the edge let alone a box cutter, I'm quite dexterous. Before I replaced mine I watched someone jam a spudger down there to get it out. Maybe my spudger wasn't thin enough but I could see the main back glass flexing while I did it so I tried something different..
I realize yours is pre-cracked, but just detailing everything I did.
What worked for me:
1) apply just enough force between the lens and the edge, you want a crack to extend outward to the edge, but avoid having dust near the actual camera lens. Saw a video of someone puncturing a hole right where the camera lens is - not smart if you like clear pictures.
2) clean all dust now!
3) take out a shard from the edge with tweezers being careful to not puncture the tape on the under side
4) heat lens then apply a cut and shaped piece of tape on top of the lens to hold in any dust when you peel.
5) place tweezers into the edge in the hole you made where the shard was, try not to put pressure on the back glass - mine was surprisingly tough, ymmv.
6) peel the edge of the under tape slowly upward try not to bend much or the glass will make a ton of dust.
7) vacuum and use compressed air around the opening.
Hope that helps.

Thanks for the comments. New glass arrives tomorrow so I'll be going through the process then. Seems pretty straightforward, but yes, probably will avoid submerging it etc just to be safe.
As far as cleaning the lens, I will use acetone (cotton balls) and compressed air. Good?

No acetone, just alcool

Just an FYI: Thin solvent liquids like alcohol will seep in the gap between the lens cover and the glass back and onto the sticky reflective tape discoloring it. I've seen it a bunch of times with the G6, the effect is worse with replacement lens covers as there isn't any adhesive on the edge.
If I was to redo this job, I'd consider using some B-7000 applied with a tiny brush around the thin edge of the lens cover to seal it. Once dry I wouldn't be concerned about cleaning with alcohol. Maybe depends how obsessive you are lol.
As always YMMV, hope the replacement goes well.
Pic shows discoloration around the edge.
https://i.imgur.com/6JB3uuc.jpg

Dust in my Front and Rear Camera Lenses

Hi guys, so I have a Galaxy S10+ for like 2 months now and the problem is that I have these little visible specks on the front and rear camera covers of the phone. They don't interfere with the quality of the images taken but it bothers me because I thought that the phone was supposed to be IP68 water and dust resistant. Can the phone still be returned to where I bought it? And is it still under warranty?
I live in the Philippines and I got the Prism Green version.

JC1715962 said:
Hi guys, so I have a Galaxy S10+ for like 2 months now and the problem is that I have these little visible specks on the front and rear camera covers of the phone. They don't interfere with the quality of the images taken but it bothers me because I thought that the phone was supposed to be IP68 water and dust resistant. Can the phone still be returned to where I bought it? And is it still under warranty?
I live in the Philippines and I got the Prism Green version.
Click to expand...
Click to collapse
The question I'd be asking myself is, would I want some tech tearing apart my device to remove dust or not. Not unless they will swap it out for another unit.
Sent from my SM-G975U using Tapatalk

My S8 had dust in front and rear camera lens as well but only after servicing.. two times repaired.. first time it had fingerprint mark on rear camera glass and dust specks on both front and rear camera glass. Second time they cleaned the fingerprint mark but still the dust speck was there when they returned it to me. Also, there was adhesive sticky sounds coming from my s8 when I pressed it on right side. They said it is not possible for them to create a factory like scenario to do a supertight sealing under vaccum and dustfree conditions but ensured that my phone will stay dustproof and waterproof after repair.
My iPhone X came out of the box with scratches and scuffs on the metal frame + dust specks inside both rear and front glass.
My s10+ luckily didnt had any dust specks inside either of the camera glass but had a minor scratch on the backside (seemed to be due to dust) inside the box or during manufacturing. They didnt had any return or refund policy so had to accept it.

Recommended adhesive for rear lens cover?

I've bought a replacement lens cover for the rear camera on my V20. It came with self-adhesive, but the adhesive isn't good enough and it keeps falling off. I really don't want to use superglue to secure it. Can anyone recommend a good alternative which will keep it in place, but which won't be a pain in the neck if the lens cover gets smashed again and needs to be replaced?