Related
How to get your custom flash count to 0 to return your device for warranty.
I did this on p3110 jellybean 4.2.2
Should work on other versions as well.
Required: Root access, Triangle Away, Odin Mobile , stock recovery image
As you all know, to get root access you need to flash custom recovery which increases your flash counter. But you need root access to to get triangle away to work. If you have custom recovery, every time the device restarts it automatically counts customs flash to 1....
But as you know flashing samsung stuff will not count towards the flash counter
1. Restore your tablet to stock: http://forum.xda-developers.com/showthread.php?t=2283598
Now in your freshly stock device:
2. Root your device,
http://forum.xda-developers.com/showthread.php?t=1957160
This will increase your custom flash count.
3. Install Triangle away, Odin mobile.
4. Copy stock recovery image onto your device.
5. In Triangle Away, reset flash counter to 0. DO NOT REBOOT your device. At the moment your flash count is 0.
6. In Odin Mobile on your device, flash the stock recovery image. Your device is fully samsungified right now so flash counter will not increase everytime it reboots.
7. Odin mobile will automatically reboot once the flashing is done.
8. Your device will have a boot error which it will fix by itself (happened to me, not to sure it will happen to you)
Check your download mode on your device, it should say:
Custom Binary Download: No
Current Binary: SAMSUNG_OFFICIAL
I attached stock recovery image from Jellybean 4.2.2;
I tested it on Jellybean 4.1.2 it works as well.
Thank You.
Please rename ur thread as [GUIDE][HOW TO] RESET BINARY COUNTER
It seems more friendly and good otherwise people will mistaken u as a noob asking questions in development section seeing ur thread name.
Thanks for the guide.
Good guide. :good:
Can someone post recovery img for p3100, stock 4.1.2?
---------- Post added at 10:37 PM ---------- Previous post was at 10:35 PM ----------
You might forget to mention about unroot .
download rom e.g. from www.samsung-updates.com ; open the *.tar.md5 file and extract the recovery.img from there
If you are on Windows:
You can convert "recovery.img" by using Flashable-Recovery-Converter-P31XX-V1.7 into a flashable zip too (if you want to flash over CWM, PhilZ Touch or TWRP instead of MobileOdin).
Download and ectract trhe zip, put "recovery.img" into the same folder an run the "P31XX-flashable-recovery-converter.bat".
idhbar said:
Can someone post recovery img for p3100, stock 4.1.2?
---------- Post added at 10:37 PM ---------- Previous post was at 10:35 PM ----------
You might forget to mention about unroot .
Click to expand...
Click to collapse
Is this about unrooting or reseting the counter?
Think before you post.
Luigi2012SM64DS said:
Is this about unrooting or reseting the counter?
Think before you post.
Click to expand...
Click to collapse
Check out the first line of Op . It is all about get back the warrenty and unroot is the part of warrenty.
---------- Post added at 01:59 AM ---------- Previous post was at 01:34 AM ----------
I think you got your answer .
Hi guys,
i hope you can help me
I flash the stock firmware with 4.4.2 with repartitioning, but my S4 stucks after download at the Screen "Samsung Galaxy S4" and the blue "recovery".
I tried to take out the battery for some minutes and retry with Odin. Unfortunately the result is the same. I don't know what to do now :crying: Pls Help.
Vince
I'd use Odin to reflash stock system image again. You may have screwed it with partitioning though, you should flash without it. But use Odin to flash again and hopefully will resolve. May be a bad download of the firmware last time too, make sure to check the MD5 after download.
---------- Post added at 12:08 PM ---------- Previous post was at 12:07 PM ----------
The other option is to try flashing a new recovery only in Odin if that's Al your after getting too to flash an alternate ROM.
thanks for the answer. i don't find the checksum of the md5, so i tried with different files. the phone still stuck at the blue "recovery" screen.
Is there another way to restore everything? i can´t enter Recovery Mode with costume recovery (TWRP, CWM)
IIIIkoolaidIIII said:
I'd use Odin to reflash stock system image again. You may have screwed it with partitioning though, you should flash without it. But use Odin to flash again and hopefully will resolve. May be a bad download of the firmware last time too, make sure to check the MD5 after download.
---------- Post added at 12:08 PM ---------- Previous post was at 12:07 PM ----------
The other option is to try flashing a new recovery only in Odin if that's Al your after getting too to flash an alternate ROM.
Click to expand...
Click to collapse
does anyone has another idea? it hasn't hard broken i think, because i can access download mode.
Xv1nX said:
does anyone has another idea? it hasn't hard broken i think, because i can access download mode.
Click to expand...
Click to collapse
Sorry if flashing via Odin is not working then your in trouble. Have you tried following this guide to the letter?
http://forum.xda-developers.com/showthread.php?t=2419762
---------- Post added at 04:17 PM ---------- Previous post was at 04:17 PM ----------
IIIIkoolaidIIII said:
Sorry if flashing via Odin is not working then your in trouble. Have you tried following this guide to the letter?
http://forum.xda-developers.com/showthread.php?t=2419762
Click to expand...
Click to collapse
Also going through the Q/A to find a bunch of other solutions mat help:
http://forum.xda-developers.com/showthread.php?t=2419762
all those didn´t solve the problem. Can JTAG repair solve the problem? i would send my phone to a Jtag repairperson if he can repair it. What do you guys think?
IIIIkoolaidIIII said:
Sorry if flashing via Odin is not working then your in trouble. Have you tried following this guide to the letter?
http://forum.xda-developers.com/showthread.php?t=2419762
---------- Post added at 04:17 PM ---------- Previous post was at 04:17 PM ----------
Also going through the Q/A to find a bunch of other solutions mat help:
http://forum.xda-developers.com/showthread.php?t=2419762
Click to expand...
Click to collapse
Sounds like you've lulled your phone then. It's worth trying any company to see if they can fix it.
Q&A for [SM-G900*] CF-Auto-Root
Some developers prefer that questions remain separate from their main development thread to help keep things organized. Placing your question within this thread will increase its chances of being answered by a member of the community or by the developer. Thanks for understanding and for helping to keep XDA neat and tidy! :smile:
please help me for root s5 dous SM-G900FD
please help me for root s5 dous SM-G900FD
I want it work for G9009W badly !!!
Any hints on G9009WKEU1ANH9 (China Telecom Dual Sim) ? I flashed G9009D (3G version) and failed.
Thank you !
samsung galaxy copy model Bepa-G900w
can you help me to root this phone?
binojthayyil said:
please help me for root s5 dous SM-G900FD
Click to expand...
Click to collapse
river268 said:
Any hints on G9009WKEU1ANH9 (China Telecom Dual Sim) ? I flashed G9009D (3G version) and failed.
Click to expand...
Click to collapse
IEric said:
can you help me to root this phone?
Click to expand...
Click to collapse
Look here for device CF_Auto Root click the download link
Then flash using Odin download here extract files from the zip
A good guide to Odin here its in the S3 forum but the process is the same
This process will trip Knox warranty
1. Download Odin from the link above and extract the Odin folder from the zip file to your PC
2. Download the CF-Auto Root from the link above extract the md5 file from the zip and put it in the Odin folder.
3, Click the link to the Odin flashing guide and follow the process shown
costom rom for Bepa-900W ????
can you point me to a custom rom that fits the phone, I have rooted it
about G9009W
ag4751 said:
Look here for device CF_Auto Root click the download link
Then flash using Odin download here extract files from the zip
A good guide to Odin here its in the S3 forum but the process is the same
This process will trip Knox warranty
Click to expand...
Click to collapse
Hi, Thanks for your information.
G9009W is not in the CF-Auto-Root device list. So I just wonder if any chance to have it done. I just failed uploading the recovery.img file here, why ?
Again, thank you from those struggling with rooting this "not so hot" model.
river268 said:
Hi, Thanks for your information.
G9009W is not in the CF-Auto-Root device list. So I just wonder if any chance to have it done. I just failed uploading the recovery.img file here, why ?
Again, thank you from those struggling with rooting this "not so hot" model.
Click to expand...
Click to collapse
Its not me the link is to Chainfire CF-Auto Root thread put you recovery.img in a zip file, click the link here scroll down to the second post and click reply to it then ask Chainfire if he can make a CF-Auto Root for your device as its not already listed, add your zip file to your post direct from your PC so he has the recovery image.
Also give him the details of the device model
no post permission
ag4751 said:
Its not me the link is to Chainfire CF-Auto Root thread put you recovery.img in a zip file, click the link here scroll down to the second post and click reply to it then ask Chainfire if he can make a CF-Auto Root for your device as its not already listed, add your zip file to your post direct from your PC so he has the recovery image.
Also give him the details of the device model
Click to expand...
Click to collapse
thanks for your always timely info to a newbie like me.
I have the recovery.zip ready, but have no permission to post.
can not root S5
Hello,
I am familiar with the kind of rooting of chainfire. I did it also wit my s4, s3, s2. But the problem is now when i want to root and odin start to make recovery.img he fails.
How can i solve this?
thanks for help.
river268 said:
thanks for your always timely info to a newbie like me.
I have the recovery.zip ready, but have no permission to post.
Click to expand...
Click to collapse
Can you upload yourself to a server location such as Google Drive, Dropbox etc then get the link and simply paste it into your message to Chainfire so don't try to post the actual link just a text version in your message body so it would look like this http:// www .mediafire.com/download/12iuwe7ja320bbl/Odin_v3.07.zip
It is a new member restriction stopping you posting the actual link, don't know if this will work though but give it a try.
---------- Post added at 05:15 PM ---------- Previous post was at 04:55 PM ----------
RUTGERMARTIJN said:
Hello,
I am familiar with the kind of rooting of chainfire. I did it also wit my s4, s3, s2. But the problem is now when i want to root and odin start to make recovery.img he fails.
How can i solve this?
thanks for help.
Click to expand...
Click to collapse
If you have flashed with Odin before you will know the process but just in case you have missed something below is what you need and what to do, the original Samsung S5 USB cable is important to use, I tried originally with my S3 USB cable and it failed, swapped it for the S5 cable and flashed straight away without any problem.
1. A recent version of Odin like the one in my earlier link.
2. Extracted the md5 image from the CF-Auto Root zip file
3. You a\re using the original Samsung S5 USB cable and not any other micro USB cable
4. You have the most recent Samsung drivers installed
The best way to ensure you keep these up to date is to install Kies 3, you don't need to use it but it is best for keeping the drivers up to date
5. If you do have Kies installed make sure it is not running even in the background when using Odin
6. Put your phone in download mode and connect to your PC
7. Start Odin and wait for the ID;Com to indicate usually highlighted in blue
8. Click the PDA and locate your CF-Auto Root md5 file
9. Wait for Odin to check the file
Once checked and ready click start and let the process run, the phone will reboot once finished and you should have root.
Android 5.0 Galaxy S5 T-Mobile
Hi,
I apologize in advance if this has been answered, but I've been searching online for a while and can't get a clear cut answer.
I rooted my Galaxy S5 back in May using Chainfire AutoRoot for the T-Mobile version, SM-g900t. Haven't flashed anything since; just wanted to have root access for a couple apps.
When Android 5.0 Lolipop rolls out to the Galaxy S5, how can I update my phone to that? Would I have to unroot, update to Lolipop OTA, and root again? (if so, would I have to find a different method of rooting or can I use the same Chainfire AutoRoot?)
Or is there a way to update to Lolipop without losing my root?
Thanks, in advance.
G9009W
ag4751 said:
Can you upload yourself to a server location such as Google Drive, Dropbox etc then get the link and simply paste it into your message to Chainfire so don't try to post the actual link just a text version in your message body so it would look like this http://www.mediafire.com/download/12iuwe7ja320bbl/Odin_v3.07.zip
It is a new member restriction stopping you posting the actual link, don't know if this will work though but give it a try.
---------- Post added at 05:15 PM ---------- Previous post was at 04:55 PM ----------
If you have flashed with Odin before you will know the process but just in case you have missed something below is what you need and what to do, the original Samsung S5 USB cable is important to use, I tried originally with my S3 USB cable and it failed, swapped it for the S5 cable and flashed straight away without any problem.
1. A recent version of Odin like the one in my earlier link.
2. Extracted the md5 image from the CF-Auto Root zip file
3. You a\re using the original Samsung S5 USB cable and not any other micro USB cable
4. You have the most recent Samsung drivers installed
The best way to ensure you keep these up to date is to install Kies 3, you don't need to use it but it is best for keeping the drivers up to date
5. If you do have Kies installed make sure it is not running even in the background when using Odin
6. Put your phone in download mode and connect to your PC
7. Start Odin and wait for the ID;Com to indicate usually highlighted in blue
8. Click the PDA and locate your CF-Auto Root md5 file
9. Wait for Odin to check the file
Once checked and ready click start and let the process run, the phone will reboot once finished and you should have root.
Click to expand...
Click to collapse
Ok, I'll give it a try and report back.
thanks
how to root chinese s5 sm-g900h
chinese s5 sm -g900h....how to root dis mobile,pls help....a problem also about the internal storage only 14mb
watut71 said:
chinese s5 sm -g900h....how to root dis mobile,pls help
Click to expand...
Click to collapse
Read the 5th post of this thread everything you need for flashing is there.
---------- Post added at 11:34 AM ---------- Previous post was at 11:24 AM ----------
river268 said:
Ok, I'll give it a try and report back.
thanks
Click to expand...
Click to collapse
Forgot to put the spaces in, it should look like this http:// www .mediafire.com/download/12iuwe7ja320bbl/Odin_v3.07.zip
Put a space each side of www so it wont be seen as a URL, then when it is copied into a browser the spaces each side of the www need to be deleted and it should work
SM-G9006W
Please,
Do you know how I root for an model SM-G9006W?
Thank you!
Pleaaase help
during this root process and when flashing, odin stopped at "cache" and then said FAIL and now its says firmware upgrade encountered an issue. Please select recovery mode in kies and try again. please someone help me
CF-Auto Root for GS5
Hi I am trying to root a Samsung Galaxy S5 it's model number is SM-G870A if someone could direct me to where I need to download the file that would be great.
Thanks, Luke
Soft Brick?
Hello,i flashed with Odin 3.07 my SM-G900F and it now stops loading at the Samsung Galaxy S5(Boot Screen?).I tried only the CF Autoroot that you suggested and also tried re-starting the process step by step.I wiped/factory reset but still nothing.I can go in both ODIN and RECOVERY screens,a solution would be heaven as i do not want to multi-pick the phone from other roms,stock rom as you prefer is my one and only choice Thanks
---------- Post added at 11:15 AM ---------- Previous post was at 11:03 AM ----------
Hello,i flashed with Odin 3.07 my SM-G900F and it now stops loading at the Samsung Galaxy S5(Boot Screen?).I tried only the CF Autoroot that you suggested and also tried re-starting the process step by step.I wiped/factory reset but still nothing.I can go in both ODIN and RECOVERY screens,a solution would be heaven as i do not want to multi-pick the phone from other roms,stock rom as you prefer is my one and only choice!
Doing it a third time i read that RECOVERY IS NOT SEANDROID ENFORCING,i am not familiar with adb(pc version) flashing ,what is the 2nd solution?
Root
Do you have plans for SM-G900V
[email protected]
thanks
Hello all. I have been at this for a few weeks trying to get it figured out on my own before I posted here, but I am a little lost now. I've been following guides by Chainfire & jrkruse and I (after many attempts and researching threads on here) successfully rooted & unlocked my bootloader (thanks goes out to them, as well as phhussen and everyone else on this forum who has posted results on getting this type of stuff done, I could not have done it without you). Now I'm trying to get safteynet to pass (so I can play pokemon go with root) - this is where I am getting stuck.
I'm trying to use a suhide solution, but I could never get the phone to pass safetynet after I unrooted (so naturally, suhide isn't going to do me much good based off of the instructions, I was just trying it as a last resort to see if I could get it to work anyway with it installed). I think I need a stock rom, but I want to keep my recovery (so that way I can easily flash a rooted rom of MM or any other changes like suhide in there). Is there a way to do this? I can't seem to find any solution other than reformatting the device and flashing a stock image posted by jrkruse of lollipop (then upgrade to marshmellow via Verizon Desktop Agent). Is there no way to just flash a stock version of the OS, but keep the recovery / bootloader unlocked?
TL;DR: I am trying to get a close to stock OS installed (without root) and get safetynet passing. Then I will attempt to follow the suhide tutorial. I want to keep my bootloader unlocked and to keep my recovery. Is this possible to do? I have TWRP (latest version) installed on my Samsung Galaxy S5 G900V.
Yeah just flash in odin all partitions except recovery and sbl aboot and rpm download the firmware you want to be on then use 7 zip file manager and extract tar file and add to and choose all other partitions and make it a tar file and Flash it in Odin
Sent from my SM-G900F using Tapatalk
So I understand what odin is and extracting selective files by using 7zip, but I'm still not quite sure where I would get the stock image of everything. I can't seem to find an unmodified version of the entire MM image. I can only find the lollipop one from jrkruse.
EDIT: If it helps any, I am already on a version of MM with MM firmware.
Pd1 firmware is available on Sammobile. Com
Sent from my SM-G900F using Tapatalk
---------- Post added at 04:11 PM ---------- Previous post was at 04:11 PM ----------
Pd1 mm firmware
Sent from my SM-G900F using Tapatalk
[email protected] said:
Pd1 firmware is available on Sammobile. Com
Sent from my SM-G900F using Tapatalk
---------- Post added at 04:11 PM ---------- Previous post was at 04:11 PM ----------
Pd1 mm firmware
Sent from my SM-G900F using Tapatalk
Click to expand...
Click to collapse
Does it matter that I am PBF4? I'm assuming PD1 is lollipop firmware? I'm looking for Marshmellow. I could flash in Odin the lollipop stock everything right now. But then since I couldn't find a stock marshmellow image (at the moment), I would be stuck on lollipop.
Pd1 is marshmallow firmware
Sent from my SM-G900F using Tapatalk
I downloaded the PF4 version from sammobile.com (that is the current version I have on my phone now). Thanks for the link for that site. The way I am understanding you is just to take that compressed file, extract all but aboot.mbn, rpm.mbn, and sbl1.mbn, and then take those extracted files and create a .tar file; then flash with Odin - is this correct?
Yes that is true
Sent from my SM-G900F using Tapatalk
When I did that nothing changed (although odin said it flashed everything successfully in the logs, but all my apps and SuperSU remained). I wiped my system next time and flashed everything and this time TWRP came up and said that it could not stop the stock ROM from deleting TWRP. I thought I was in the clear, but so far the first attempt has left the phone on the Verizon checkmark screen. I restored my old image and am trying one more time. I'm not sure if it is supposed to take long? I flashed a .tar with the following in it:
- boot.img
- cache.img.ext4
- modem.bin
- NON-HLOS.bin
- sdi.mbn
- system.img.ext4
- tz.mbn
Before I flashed this .tar, I wiped the System, ARK=dalvik/cache, internal storage, and cache if that helps any.
You have to do a wipe after flash
Sent from my SM-G900F using Tapatalk
Hello all,
Today I updated a custom ROM on my rooted Phone (android 7) . In the aroma installer i select no root. After a good restart i though i root my Phone true Odin. I was thinking it went all good till it was stuck on te Galaxy s7 edge black screen. I couldnt do nothing. After that i was thinking to flash to stock. Every time i try to flash true Odin it give me fail.
Please help me.
Best regards Sidi
Hi there, I have same issue, have s7 edge sm-G935F stuck at logo. I downloaded 2 different firmware from z3x box(shell) and if keep failing when using odin (latest) and also getting error when using Samsung tool.Also I can't get in the phone menu to check the baseband..can only get model from download model.any advice to this?
Same issue as well on my sm-g985v Verizon variant
Flashed an update to work out minor lagging bugs and soft bricked my S7. Can access bootloader and recovery. Beyond that, the phone gets there but with black screen and it is sputtering off and on. Tried reflashing stock firmware with odin, and its not taking. Running into a permission error while trying to write the image. Anyone here have any ideas?
sidi adam said:
Hello all,
Today I updated a custom ROM on my rooted Phone (android 7) . In the aroma installer i select no root. After a good restart i though i root my Phone true Odin. I was thinking it went all good till it was stuck on te Galaxy s7 edge black screen. I couldnt do nothing. After that i was thinking to flash to stock. Every time i try to flash true Odin it give me fail.
Please help me.
Best regards Sidi
Click to expand...
Click to collapse
Is this a 935F? Where did you download the orginal firmware from and what version of Odin u use?
When I root my phone I always use the steps from this thread.
http://forum.xda-developers.com/s7-e...0-0-0-t3334084
Have never run into issues.
Flash twrp trough Odin first, let the phone start
Boot into TWRP, format phone with the options you have to type YES, then install dm-verity force encryption disabler
Now restart TWRP
Then flash the Supersu file from the thread.
Now restart phone
---------- Post added at 10:44 PM ---------- Previous post was at 10:42 PM ----------
Feyaad said:
Hi there, I have same issue, have s7 edge sm-G935F stuck at logo. I downloaded 2 different firmware from z3x box(shell) and if keep failing when using odin (latest) and also getting error when using Samsung tool.Also I can't get in the phone menu to check the baseband..can only get model from download model.any advice to this?
Click to expand...
Click to collapse
Download orginal firmware fro sammobile, unpack and flash with Odin 3.12.3.
Download the firmware from your area, the one that comes with your phone.
Use the right regional code and everything when you download firmware.
Also, have you guys flashed the right bootloader and modem beforehand?
LyLu said:
Is this a 935F? Where did you download the orginal firmware from and what version of Odin u use?
---------- Post added at 10:44 PM ---------- Previous post was at 10:42 PM ----------
Download orginal firmware fro sammobile, unpack and flash with Odin 3.12.3.
Download the firmware from your area, the one that comes with your phone.
Use the right regional code and everything when you download firmware.
When I root my phone I always use the steps from this thread.
http://forum.xda-developers.com/s7-edge/development/recovery-official-twrp-hero2lte-3-0-0-0-t3334084
Have never run into issues.
Flash twrp trough Odin first, let the phone start
Boot into TWRP, format phone with the options you have to type YES, then install dm-verity force encryption disabler
Now restart TWRP
Then flash the Supersu file from the thread.
Now restart phone
Click to expand...
Click to collapse
Hello,
Thanks for your message. I tried everything you said exept that i used odin 3.12.5
But still the black screen...
sidi adam said:
Hello,
Thanks for your message. I tried everything you said exept that i used odin 3.12.5
But still the black screen...
Click to expand...
Click to collapse
What rom you tried to flash?
Are you on the right bootloader and modem?
Well I have the Odin latest version already..but I can't know which is the correct baseband or county..only the model I know when it's in download mode..
sidi adam said:
Hello all,
Today I updated a custom ROM on my rooted Phone (android 7) . In the aroma installer i select no root. After a good restart i though i root my Phone true Odin. I was thinking it went all good till it was stuck on te Galaxy s7 edge black screen. I couldnt do nothing. After that i was thinking to flash to stock. Every time i try to flash true Odin it give me fail.
Please help me.
Best regards Sidi
Click to expand...
Click to collapse
So you flashed a beta firmware, the name of which you don't feel is necessary information.
OK. Shame I hate popcorn. How about INFORMATION instead?!
LyLu said:
Is this a 935F? Where did you download the orginal firmware from and what version of Odin u use?
When I root my phone I always use the steps from this thread.
http://forum.xda-developers.com/s7-e...0-0-0-t3334084
Have never run into issues.
Flash twrp trough Odin first, let the phone start
Boot into TWRP, format phone with the options you have to type YES, then install dm-verity force encryption disabler
Now restart TWRP
Then flash the Supersu file from the thread.
Now restart phone
---------- Post added at 10:44 PM ---------- Previous post was at 10:42 PM ----------
Download orginal firmware fro sammobile, unpack and flash with Odin 3.12.3.
Download the firmware from your area, the one that comes with your phone.
Use the right regional code and everything when you download firmware.
Also, have you guys flashed the right bootloader and modem beforehand?
Click to expand...
Click to collapse
It was my understanding it was already in the package. Questioning that one now. Where do i look for that? And thank you for responding back. Downloading your first suggestions as i type this...
I have downloaded two non branded firmware for the Netherlands from samdroid. I had unpacked the zip and flashed the files. For the csc selection I put the one named home csc
Moodruid said:
It was my understanding it was already in the package. Questioning that one now. Where do i look for that? And thank you for responding back. Downloading your first suggestions as i type this...
Click to expand...
Click to collapse
When downloading original firmware there should be 4 files when unzip.
1 for each of the options in Odin, without the last one named home.
Some of the custom roms comes with bootloader and modem, but NOT ALL.
Most times you have to flash the right bootloader and modem in Odin beforehand to get the phone to boot.
Im unsure of what has happened because I have never run into issues myself.
If you can not get the phone to boot with firmware from Sammobile and Odin flash I am out of options.
If I do experience a problem like this I would:
-install bootloader and modem according to the custom rom used. Try and flash these with odin more than ones, if not working.
-if no recovery, try flash recovery again
-try flash another custom rom then another custom rom
-return to stock firmware downloaded trough Sammobile
If none of these options work im out of things to do, sorry
The times I have experienced phone stuck on Samsung logo, it has been because of bootloader and/or modem.
Flashing the right ones have always fixed the problem.
That said, I have never experienced problems with returning to stock firmware trough Odin, maybe one time.
And this time my firmware download was corrupted.
---------- Post added at 06:13 AM ---------- Previous post was at 06:00 AM ----------
sidi adam said:
I have downloaded two non branded firmware for the Netherlands from samdroid. I had unpacked the zip and flashed the files. For the csc selection I put the one named home csc
Click to expand...
Click to collapse
This is wrong, you should use the file named only CSC.
Home_CSC, is to keep your setup on phone as is.
I also remember that you have to remove the meta data directory, and then repack firmware or the install will stop.
And this is also NOT a good option if you use another firmware than the original on phone.
Installing firmware with Odin, always use BL, AP, CP and CSC.
Try this and forget about the Home_CSC.
I don't have anymore info, sorry
Thank you very much. I will try it. I will let you know.
Gentlemen, my appreciations and thanks. Was able to finally get the stock firmware to grab. After more time disecting the problem i learned about and was able to uncover the maintenance boot screen. There it had the option to do usb debug . Once i hit that, next flash finished fully. It must of reser in the dev options after the initial root. Damn, i was sweating balls for a bit thinking i must of hard bricked it somehow. I will take it throufh the toot process later today glitch free i imagine. Thanks again for assisting,
Moodruid said:
Gentlemen, my appreciations and thanks. Was able to finally get the stock firmware to grab. After more time disecting the problem i learned about and was able to uncover the maintenance boot screen. There it had the option to do usb debug . Once i hit that, next flash finished fully. It must of reser in the dev options after the initial root. Damn, i was sweating balls for a bit thinking i must of hard bricked it somehow. I will take it throufh the toot process later today glitch free i imagine. Thanks again for assisting,
Click to expand...
Click to collapse
Usb debugging should always be turned ON when flashing..........!
Tis is like common knowledge in here.
Anyway glad things work
LyLu said:
Usb debugging should always be turned ON when flashing..........!
Tis is like common knowledge in here.
Anyway glad things work
Click to expand...
Click to collapse
How will you get to turn on USB debugging when the phone can only booth into download model?
Feyaad said:
How will you get to turn on USB debugging when the phone can only booth into download model?
Click to expand...
Click to collapse
Buy pressing and holding power and volume down key, until you get to the screen.
Same procedure as download mode, but without the big button
LyLu said:
Buy pressing and holding power and volume down key, until you get to the screen.
Same procedure as download mode, but without the big button
Click to expand...
Click to collapse
OK great..will try it..thank you
luly said:
Is this a 935F? Where did you download the orginal firmware from and what version of Odin u use?
When I root my phone I always use the steps from this thread.
http://forum.xda-developers.com/s7-e...0-0-0-t3334084
Have never run into issues.
Flash twrp trough Odin first, let the phone start
Boot into TWRP, format phone with the options you have to type YES, then install dm-verity force encryption disabler
Now restart TWRP
Then flash the Supersu file from the thread.
Now restart phone
---------- Post added at 10:44 PM ---------- Previous post was at 10:42 PM ----------
Download orginal firmware fro sammobile, unpack and flash with Odin 3.12.3.
Download the firmware from your area, the one that comes with your phone.
Use the right regional code and everything when you download firmware.
Also, have you guys flashed the right bootloader and modem beforehand?
Click to expand...
Click to collapse
Even this thread is old:
Thank you so much, bricked my phone unknowingly flashing custom recovery using a defektive usb port struggling to get it working again. This worked like a charm.
Don´t understand why the orthers did struggle with that method.