Related
I made these odin flashable firmwares for those who need them. This is only the stock firmware for Lollipop 5.01 build OB7. (NO system or data partitions) If you need to flash the stock OB7 firmwares then this will do that for you. This will not wipe your system or data.
Once you flash the "OB7-FW.tar.md5" you must reroot and flash a custom recovery if you want to flash custom roms etc. Simply odin flash cf-auto-root and the latest recovery by TWRP and you'll be back in business.
The OB7-modem.tar.md5 requires no extra steps... it's just the modem.
I have tested these packages on my Note 4 running OB7 firmware. Note: If you are on OE1 firmware, you will NOT be able to flash this OB7 firmware successfully due to new security measures in the OE1 bootloader.
OB7-FW.tar.md5 This tar package includes all of the stock OB7 firmware including kernel,modem, recovery, bootloader, etc. Please flash this in odin on your PC ONLY!
OB7-modem.tar.md5 This tar package includes only the modem and HLOS patch. Can be flashed with odin on your pc and also mobile odin.
Gonna try
tx_dbs_tx said:
I made these odin flashable firmwares for those who need them. They are the stock firmware for Lollipop 5.01 build OB7. If you need to go back to the OB7 firmwares then give this a try. This will not wipe your system or data.
Once you flash the "OB7-FW.tar.md5" you must reroot and flash a custom recovery if you want to flash custom roms etc. Simply odin flash cf-auto-root and the latest recovery by TWRP and you'll be back in business. The OB7-modem.tar.md5 requires no extra steps... it's just the modem.
I have tested these packages on my Note 4 running OB7 firmware. OE1 bootloader/recovery may not allow flashing back to older firmware. (I haven't tested with OE1 firmware) Please report your success or failure when flashing this over your OE1 firmware.
OB7-FW.tar.md5 This tar package includes all of the stock OB7 firmware including kernel,modem, recovery, bootloader, etc. Please flash this in odin on your PC ONLY!
OB7-modem.tar.md5 This tar package includes only the modem and HLOS patch. Can be flashed with odin on your pc and also mobile odin.
Click to expand...
Click to collapse
I just tried this and I got the following error:
UDC START
SW RED CHECK FAIL : [tz]Fused 2 > Binary 1
I am using Odin 3.07, running Windows 7.
tx_dbs_tx said:
I made these odin flashable firmwares for those who need them. They are the stock firmware for Lollipop 5.01 build OB7. If you need to go back to the OB7 firmwares then give this a try. This will not wipe your system or data.
Once you flash the "OB7-FW.tar.md5" you must reroot and flash a custom recovery if you want to flash custom roms etc. Simply odin flash cf-auto-root and the latest recovery by TWRP and you'll be back in business. The OB7-modem.tar.md5 requires no extra steps... it's just the modem.
I have tested these packages on my Note 4 running OB7 firmware. OE1 bootloader/recovery may not allow flashing back to older firmware. (I haven't tested with OE1 firmware) Please report your success or failure when flashing this over your OE1 firmware.
OB7-FW.tar.md5 This tar package includes all of the stock OB7 firmware including kernel,modem, recovery, bootloader, etc. Please flash this in odin on your PC ONLY!
OB7-modem.tar.md5 This tar package includes only the modem and HLOS patch. Can be flashed with odin on your pc and also mobile odin.
Click to expand...
Click to collapse
ive been searching but can you help me put stock 0e1 recovery back on my phone i forgot to factory data reset after i updated to 0e1 and rerooted and now my phone is super buggy and i think its because i didnt wipe on stock recovery which usually fixes my problems. thanks if you can help or not. ive wiped on twrp of course but my stock rooted 0e1 rom just isnt right idk but like i said the stock recovery to me really wipes evrything. ive tried aosp roms but there even more buggy can you please help thanks
No one has it yet
Right. There is no official tar ball available for OE1 firmware. OTA is the only way right now and nobody has pulled and uploaded the update zip for OE1. Im afraid you're gonna have to try the OB7 official rom tar or else you're stuck until a tar pops up somewhere. And that may not happen for OE1.
PeteSeiler2010 said:
I just tried this and I got the following error:
UDC START
SW RED CHECK FAIL : [tz]Fused 2 > Binary 1
I am using Odin 3.07, running Windows 7.
Click to expand...
Click to collapse
Thanks for the report. Which software version are you currently on? Extension OB7 or OE1 ??? You must be on OE1 because it flashed successfully on my OB7 software. I will upload another version for you to test.
Yes, I am on OE1, I will gladly test for you. Just keep me posted.
So just to clarify, if I am on KK, I can ODIN this then cf auto root then TWRP? And don't take the update to OE1 because it's not worth it?
Sent from my SM-N910P using XDA Free mobile app
beezar said:
So just to clarify, if I am on KK, I can ODIN this then cf auto root then TWRP? And don't take the update to OE1 because it's not worth it?
Sent from my SM-N910P using XDA Free mobile app
Click to expand...
Click to collapse
Ok, don't mess with this, it's for a different purpose. Read the OP in @tx_dbs_tx 's hybrid X 2.2 rom thread here:
http://forum.xda-developers.com/showthread.php?t=2956667
Read the OP carefully as there is a VERY specific procedure (it's easy) you MUST follow to move up to lollipop.
Stock tar in the OP here:
http://forum.xda-developers.com/showthread.php?t=3056478
If you'd rather have a stock rom instead of hybrid x download the stock tar and follow tx's instructions to the T in his Hybrid-X OP before flashing it or any lollipop based rom.
Remember, you MUST flash the stock OB7 tar BEFORE flashing any lollipop rom.
EDIT: If you decide to go stock, do not take the ota. Once you cf-auto-root & odin twrp you won't have to worry about it anymore. The same with Hybrid-X. Once you flash that no more OTA worries.
Did u find the hidden image ??
I'm not going to pursue the OE1 secured bootloader thing. We will have to wait for an official tar ball and rebuild roms from it. Until then I'm staying on my OB7 rom.
I dont quit but thanks for your efforts
pbedard said:
I dont quit but thanks for your efforts
Click to expand...
Click to collapse
Have at it... Keep us posted.
Meh sourcecode is out
So i have spent the last 4-5 hrs trying to get this phone to work for my brother and i am stuck at the moment. Need some help
Ever since OC4, i never updated the bootloader, only the ROM. phone was in OK3....I followed the thread for unlocking the bootloader, and gained the MODE: Developer.
I tried to follow the thread for muniz and got the files i needed.
Once i got MM up, noticed that WIfi, capacitive buttons wouldnt work. So i reverted back to PB1 downgrade.
i once again followed the steps and got MM back into the phone, but still the same problem as above.
Here is how the phone is currently:
Bootloader screen: " Current binary custom,system status custom, reactivation off, qualcomm secureboot enable (CSB), AP SWREV S1,T2,R1,A1,P1 and MODE: Developer, UDC Start
Recovery : Currently it boots to TWRP 3.0.2-2
Once booted into android, i used Samsung Mobile Info.
Build Number: MMB29M.G900VVRU2DPD1
Kernel version: 3.4.0-8025411
PDA: G900VVRU2DPD1
CSC: G900VVRU2DPD1
Baseband: G900VVRU2DPD1
Bootloader: G900VVRU1BOC4
So, can i just update the bootloader to MM, unlock it, re root, and fix? DO i have to revert once again to PB1?
I need some direction as to how get bootloader to PB1 or PD1...
Thanks
Exact same problem here. I've been struggling with this for about a week now. PD1 bootloader will NOT flash in Safestrap or FlashFire. I even tried TWRP for the heck of it.
Sent from my SM-G900V using XDA-Developers mobile app
I had the same problem that I could not get the buttons to work over several days several and several different methods, each time having to ODIN back to PB1. Two of the times I even had to go find a flash file for firmware because the ODIN did not restore the bootloader back to PB1. When I did finally get it to work I followed the information in the OP for unlocking the BL that I will paste below the main thing being place the ROM on the phone storage not the SD as the files flashed below use the TWRP that doesn't see SD cards
Download these 2 files and place on phone And A Custom Rom
PB1_Flashfire_Prepare.zip https://www.androidfilehost.com/?fid=24572369242686444
PD1_Firmware_With_Dev_Aboot_Twrp_Recovery_Image_Flashfire_Only.tar.zip https://www.androidfilehost.com/?fid=24572369242686471
Reboot to TWRP and flash PB1_Flashfire_Prepare.zip
Reboot
Open Flashfire (It will be installed by the zip you flashed in TWRP) grant supersu permission
Goto Flashfire Settings check box to Flash bootloaders and uncheck box for Emulate framebuffer
Goto Actions
Now add Flash firmware package and choose PD1_Firmware_With_Dev_Aboot_Twrp_Recovery_Image_Flashfire_Only.tar.zip
Now manually check on all the partions to flash. Check them all make sure to scroll down. Now click check mark at top right for ok
Now on the warning dialog that pops up about splitting protected partitions select no
Now in the actions dialog box where it says reboot change that to recovery
So it should look like this
Flash firmware package
Primary Bootloader
Secondary Bootloader
Etc........
EverRoot
EverRoot Disabled
Reboot
Recovery
Click FLASH
When finished phone will reboot to TWRP
Wipe Data, Wipe Cache, Wipe System
Install Custom Rom
For the custom rom I used the one from here labeled G900V_PD1_Stock_Rooted_ROM.zip http://forum.xda-developers.com/ver...w-to-update-to-g900voe1-5-0-keeproot-t3149784 and the ROM took short of a min to boot past the samsung screen then roughly 8-10 mins to boot past the red Verizon screen.
Of course once it reboots and your up and going on the new rom you'll have to flash TWRP I used 3.0.0.0
Hope this helps.
---------- Post added at 03:22 PM ---------- Previous post was at 03:06 PM ----------
Oh and if you make a Nandroid backup before you try PD1, you can always ODIN flash TWRP and then just restore your previous rom (that's what I kept doing after the first 2 total losses)
TWRP https://www.androidfilehost.com/?fid=24459283995310730
Thanks ecen92!! i saw your message a bit late, but i did go back at it with a fresh mindset last night and got it working!!
Here is how i did:
So, after many reading between the lines, something about bootloaders not flashing if the kernel and firmware dont match... anyways, since i was on OC4 i almost went back to a OC4 full tar, but couldnt find it... Glad i didnt.
So i decided to see if i could restore to PB1 fully, and start from there....
I flashed the PREPARE YOUR PHONE FOR ROOT from here http://forum.xda-developers.com/verizon-galaxy-s5/general/root-method-og5-ok3-t3290370
But after it finished, now i was in PB1 but still with OC4 bootloader.... something told me to redo it.... so i did.. i RE DID the above flash again!!! and once completed i was on a full PB1 with locked bootloader.
The trick for me was that i HAD TO FLASH THE PB1 FULL TAR 2X IN A ROW!
From there i did the working root method found on the same thread http://forum.xda-developers.com/verizon-galaxy-s5/general/root-method-og5-ok3-t3290370
After i gained root, i then unlocked the bootloader based on this steps http://forum.xda-developers.com/ver...t/rd-unlocking-galaxys-s5-bootloader-t3337909
After unlocking the bootloader, then i followed the instructions labeled in light blue called "Upgrade To PD1 Rom With PD1 Unlocked Bootloader From 5.0 TW Rom With PB1 Unlocked Bootloaders" (annoying a** color to see)
After which i was then on PD1 rom rooted, PD1 unlock bootloader and no more problems with wifi, capacitive buttons not responding, etc.
Hope i can help anyone else stuck with this problem.
Good to hear you've got it all working! :good:
I will make a post for those confused that still dont know how to properly update to PF4 rooted using this post http://forum.xda-developers.com/ver...w-to-update-to-g900voe1-5-0-keeproot-t3149784
The initial instructions for rooted arent too clear. I have asked for clarification from the source and others, and my questions have fallen on deaf ears.
I had my brothers phone on PD1 rooted/unlocked, and by flashing the rooted version on the OP followed by stock PF4 bootloader, bricked the software. (The msg that it cant boot) and after D-king around for 4 hrs, i finally got it.
Anyways here is the steps i did ( i dont own steps, just trying to copy paste info to paint a clear picture)
Had to flash the PB1 full tar on ODIN
Then i had to root the PB1 as mentioned here. http://forum.xda-developers.com/verizon-galaxy-s5/general/root-method-og5-ok3-t3290370
After root i had to unlock bootloader. http://forum.xda-developers.com/ver...t/rd-unlocking-galaxys-s5-bootloader-t3337909
I used Method 2: Unlocker via Safestrap Samsung_Bootloader_Unlocker.zip in safestrap or flashfire
After this i verified i was on PB1 rooted and unlocked.
From there i went to Flashfire and flashed G900V_PF4_Stock_Rooted_ROM.zip (For "Unlocked" Bootloaders Only!) as posted on the OP
This placed me on PF4 ROM and firmware, but with a PB1 unlocked bootloader. (This is where the back button, recents and wifi dont work)
I then flashed TWRP 3.0.0 via ODIN
From there i followed the "If You Already Have Bootloader Unlocked And On A Samsung TW Rom" found here http://forum.xda-developers.com/ver...t/rd-unlocking-galaxys-s5-bootloader-t3337909
In case instructions changed, like it has on the past, they are:
In TWRP Flash TWRP_Prepare.zip
Reboot to Download Mode
In Odin Under AP slot load PB1_Firmware_Only_NK2_Kernel.tar.md5
Now in Odin Under PIT load S5_KLTE_USA_VZW.pit If you have a 32gb phone instead of 16gb phone skip this step
Click Start
When finished on reboot watch for Safestrap Splash Screen and enter Safestrap
Now goto Power Menu/Reboot Menu and reboot to Download Mode
Make sure in download mode the current binary is Official. If it is not reflash In Odin Under AP slot load PB1_Firmware_Only_NK2_Kernel.tar.md5
Now in Odin Under PIT load S5_KLTE_USA_VZW.pit
Click Start on reboot enter Safestrap reboot back to download mode and make sure binary status is Official
If Binary Status is Official Pull battery restart and enter SafeStrap
Flash: SafeStrap_PF4_Bootloader_Unlock_AIO.zip
Phone will Power Off.
Pull Battery enter download. Flash via ODIN TWRP 3.0.0 as the previous flash will install 3.2 which doesnt see the SD card.
There u go, thats it, this will have you on a rooted/unlocked PF4.
Hi,
I tried to flash a stock firmware today using odin, however it failed. On my phone it says custom boot binary blocked by fap lock, but i am flashing stock firmware only. I have never rooted or unlocked the bootloader. Now my phone is stuck in the downloading mode. How do i fix this or successfully flash?
Regards,
I tried everything, now i get a secure lock error?
To recap, i have a g935w08 and i was trying to flash the BTU firmware (G935F) which i downloaded from samfirm, i used all the BL, AP, CP, CSC (used regular CSC) and it refuses to work. I am using odin 3.12.
Who can help me with this?
Try odin 3.11.1 as it says on the download page, failing that, try and flash your original firmware.
Instructions at the bottom of this download page: https://www.sammobile.com/firmwares/download/116121/G935FXXU1BPLB_G935FBTU1BPK3_BTU/
I gave up. Could it be due to the fact that i am trying to flash a G935F firmware onto G935W?
yes that's very possible, in your post above you said you have a G935F ?
"To recap, i have a g935F and i was trying to flash the BTU firmware"
@Seanie280672 I have updated it now. Does anyone know if this is possible?
I rooted the G950F italian version with oreo according to this guide
https://forum.xda-developers.com/galaxy-s8/how-to/guide-how-to-install-twrp-root-galaxy-t3752480
.... at last step in recovery twrp i didn't permit to install again twrp and unchecked. reboot shows samsung logo and then goes off. in recovery didn't access and i was constrict to install stock recovery. now i am on stock recovery but unable to flash again the twrp for error check file bootloader device 3 binary 1.
i can't flash the official stock rom because goes error only official can install......
ONLY OFFICIAL RELEASED BINAR ARE ALLOWED TO BE FLASHED please help
i installed in s8 italian version the files linked in first post. please help
IF I TRY TO INSTALL CRF7 ROM WITH 4 FILES AND HOME CSC IT SHOWS: CHECK FILES (BOOTLOADER) DEVICE 3 BINARY 1
is like i have not more recovery and i can't reflash with odin... i need help please
That error suggests you are flashing older firmware than what's on the device
how can i solve for motivation that every flash, even the last firmware goes on???
it stucks after click start button in cosmy odin.....
i cannot flash again the twrp, i cannot flash stock firmware, i flashed only bl file, but all errors.......
what can i try?
i hope a suggest
thanks
Here are some photo....
if i try flash 3 files with csc NOT home and without bl file, the result is so:
https://ibb.co/b2UA5K
https://ibb.co/jxZGee
If i try to flash all 4 files the results is so:
https://ibb.co/b2UA5K
https://ibb.co/muYnkK
if i try to flash only twrp the result:
https://ibb.co/mCSrCz
https://ibb.co/m4Geze
Why root this phone?
What mean with my problem???
hey,
Try flashing latest firmware with patched odin
SM-G950U
I did an update from CRE2 to G950USQU5CRF6 from firmware.science and so i can't seem to upgrade any further or downgrade back and follow a different upgrade path. any help would be greatly appreciated. I have tried the 4 file odin flash for CRE2 and it fails with the sw rev check fail fused 5 > binary . I think i just need more recent odin files for the "U5" bootloader but i cant seem to find them anywhere that doesn't require a paid membership to download.
update:
Well i was able to flash a factory binary with v5 bootloader but still couldn't flash the normal 4 odin files that i found on updato.com for CRL1
... did a cache wipe and data wipe / factory reset was then able to flash the 4 odin files to get me up to CRL1
i probably didn't need to flash the factory binary but it is a step i took.