Database Users

Help!! I can not use Odin to Flash anymore

Help please
My tab is stuck at downloading
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
***never mind*** I restarted the computer and used another usb port....everything was fine again

[Q] Need help with odin!

I have an AT&T Samsung Galaxy s4 that I rooted on 4.3. I wanted to update and keep root, so I was going to flash a rom using safestrap. I downloaded the rom and kernel. Then I booted into download mode and it got stuck. So I took out the battery and went into recovery mode. I wiped everything and factory reset it. Now I searched up that I can use odin v3.09 to get out of the brick(only loading the logo). After I got this
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337UCUAMDB_I337ATTAMDB_I337UCUAMDB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<OSM> All threads completed. (succeed 0 / failed 0)
<OSM> All threads completed. (succeed 0 / failed 0)
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/004> Removed!!
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/004> Removed!!
<ID:0/004> Added!!
What can I do?

bump

Firefrazed said:
I have an AT&T Samsung Galaxy s4 that I rooted on 4.3. I wanted to update and keep root, so I was going to flash a rom using safestrap. I downloaded the rom and kernel. Then I booted into download mode and it got stuck. So I took out the battery and went into recovery mode. I wiped everything and factory reset it. Now I searched up that I can use odin v3.09 to get out of the brick(only loading the logo). After I got this
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337UCUAMDB_I337ATTAMDB_I337UCUAMDB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<OSM> All threads completed. (succeed 0 / failed 0)
<OSM> All threads completed. (succeed 0 / failed 0)
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/004> Removed!!
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/004> Removed!!
<ID:0/004> Added!!
What can I do?
Click to expand...
Click to collapse
4.3 is MK2 and it has a locked bootloader. Due to this, you cannot flash a full image containing bootloader lower than MK2 (MDB, MDL, MF3 will not work). You can flash MK2 or newer ones. Stick to MK2.
Full MK2 can be obtained from All things AT&T MK2 and NB1 thread.
Follow Deadly Venom Kitkat Magic tool and flash a pre-rooted kitkat rom from the All things AT&T thread.

Need help with flash my S8+ with odin

Hi guys,
I'm trying to flash back to stock firmware with Odin on my phone. I have downloaded the stock firmware and loaded with Odin.
I put my phone to download mode and connect to computer. But every time when I hit start, the phone restarts and Odin shows failed. Below is the message I got:
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> FAIL! (DeviceInfo)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> FAIL! (DeviceInfo)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
<ID:0/004> Added!!
Any ideas?

Flash into stock rom on Galaxy S8 (SM-G95OU1)

Was trying to flash a custom ROM and Odin failed and now I can't flash the stock rom.
Issues are:
When in recovery mode I get a "No command" error and #fail to open recovery_cause(No such file or directory)
Will boot loop with the "Installing system update" screen
Odin log when flashing to stock ROM is:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img.lz4
<ID:0/005> Complete(Write) operation failed.
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Odin log when flashing to TWRP(3.2.1) is:
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> recovery.img
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
If it matters the boxes I have checked are auto-reboot and f. reset time. I've tried on a different PC and usb ports.
Also if this is the wrong place to put the thread then can a mod move it or somebody tell me where to put it.

UPDATE:
Found a newer Odin(3.13) and got it working by ticking DeviceInfo but I'm still getting a "no command" and "fail to open recovery_cause" errors.
Odin log when it worked:
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1301)..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)

note 4 can not flash the rom Please HELP

hi, i was using my samsung galaxy note 4 for nearly 4 years without any problems. today It went to black screen where was some info about "panic Karnel". I removed battery and everything was fine. 2 hours later when I was using snapchat phone restart and went to bootloob. I connected note 4 to odin to flash stock room and I get a massage in odin every time when I want to flash rom:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1101)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
on my phone there is massage:
"mmc_write fail"
Please help dear experts, i it any chance to fix my phone??
P.s. I tryed to use this>>> https://forum.xda-developers.com/no...te-4-pit-files-repartiton-f-g-c-t-w8-t3282641
but did not work, still get a massage:
""mmc_write fail""

x7nofate said:
hi, i was using my samsung galaxy note 4 for nearly 4 years without any problems. today It went to black screen where was some info about "panic Karnel". I removed battery and everything was fine. 2 hours later when I was using snapchat phone restart and went to bootloob. I connected note 4 to odin to flash stock room and I get a massage in odin every time when I want to flash rom:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1101)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
on my phone there is massage:
"mmc_write fail"
Please help dear experts, i it any chance to fix my phone??
Click to expand...
Click to collapse
Flash Twrp recovery via odin
In twrp Go to wipe
Wipe "system+data+cache+dalvic cache+internal storage you have to wipe 3 times or more to make sure all partations are wiped cleaned.
Then you have to download repair firmware for your specific model.
Repair firmware comes with 5 files "BL+AP+CP+CSC+PIT"
you have to extract and upload all files in odin with PIT file.
Then go to odin options and check on "nand eraseall" and "re partition"
Now boot your device into odin download mode
Now hit start and wait until finish
Then dont let phone reboot you have to boot into stock recovery and do wipe cache & factory reset then reboot.
If this method fails then there is no way to fix it unless changing logic board because your internal storage is dying thats why it shows "mmc_write fail".
You can download repair firmware from www.tsar3000.com

thank you for reply. I tryed to Flash Twrp recovery via odin but it failed. I get massage in odin:
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/004> Removed!!
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> recovery.img
<ID:0/004> RQT_CLOSE !!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I tryed few times and I am sure I was flashing the right recovery
I also did try to flah Repair firmware which comes with 5 files "BL+AP+CP+CSC+PIT" but it failed, I get message:
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Erase...
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
please help

x7nofate said:
thank you for reply. I tryed to Flash Twrp recovery via odin but it failed. I get massage in odin:
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/004> Removed!!
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> recovery.img
<ID:0/004> RQT_CLOSE !!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I tryed few times and I am sure I was flashing the right recovery
I also did try to flah Repair firmware which comes with 5 files "BL+AP+CP+CSC+PIT" but it failed, I get message:
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Erase...
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
please help
Click to expand...
Click to collapse
Try to put your phone in freezer without battery for an hour then try this method again.
Keep trying if it doesn't work then as i told you you have to replace logic board because your internal memory is dead.