hi there
i was wondering if anyone can help
i recently bought a second hand xda 1 it was working fine , but when i tried to install WM2003 it was doing ok in the installation but during the installation the whole thing froze and nothing seems to happen.
now nothing works and there is only a blank screen. i have tried to reset the whole thing but it still doesnt still work. i think everything is deleted how do i reinstall wm2002 or wm2003 .
the active sync doesnt connect anymore
please someone help me
What install/upgrade method did you use SD or PC install?
Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.
did you try a hard reset ?
Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.
Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.
I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.
Can any one help me in this regard please.
I am having the same problem, but my phone is not sim-locked.
I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated
Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.
ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!
Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck
Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.
mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks
(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452
hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin
Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.
collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)
Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.
just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...
Hello Everyone
I need big time help. I just bought Hp 6945 and I tried to update GSM rom from 1.02 to 1.08, while updating it says update fail and try to restart Ipaq and start again. Now My problem is Ipaq just stuck to Hp invent logo. I tried to reset and hard reset and remove battery but notthing work.
I need help
Could some please help me to How to fix this problem?
Thank you
same BS happened to me. the only way to fix it is to load the UK 6915 ROM. thats the ONLY way to fix it. AVOID this update do not try to update the radio. I bricked my phone doing this. STILL looking for a solution. Radio stack is daamged.
where Can I find Uk 6915 rom
Thank you for reply. Where can I found the UK 6915 rom. Is there any instruction to How to load rom?
Thank you
If is FIXEDDDDDDDDDD
Ok
I got it fixed, very simple solution
found it here
http://pdaphonehome.com/forums/hp-h...dowloaded-rom-update-ipaq-dead-need-help.html
Solution:
this is what I did to get this fixed.
1) Get the battery out of the iPaq, and wait for a few minutes while the "serial" image fades away slowly.
2) In the meantime, prepare your cradle, plugged into the AC charger and plugged via USB to your PC.
3) After a few minutes, with the screen of the iPaq completely gray, put the battery and battery cap back on (with our without SIM card), and put it on the cradle immediately.
4) The iPaq should start coming back to life, as if it were being hard reset. Let is stay on the welcome screen (i.e., do not tap it or anything).
5) Restart the upgrade process, it should proceed from there OK
Thank you to origianl solution provider
No network connection
Ok everything work fine, but Now I cann't connect to tmobile. It keep showing me no service.
Any Help please
Ok It is fixed again
There is another update at HP website, which is software update. After installing that everything working fine.
can anyone help? i just bricked my ipaq 6965 too. had already followed those few instructions without any success.. what do you mean by "with or without SIM card"?
After a soft reset, mine's stuck at the initial blue/white boot screen.
Hard reset doesn't work (assuming its call + hang up + power + poke reset).
Ideas?
bring back to life hw6945
i'we tried like you to upgrade radio part and a got an freezed phone
Solution for repair was flashing firmware with this program..
Download-Link #1: http://rapidshare.com/files/96527845/Ipaq_HW69XX_ENG_ROM.zip.html
download files from rapidshare posted by me ,r tested on my phone
hi i have tried to dl the rom asi having the same prob but the file cannot be downloaded. is there any other way to get from you
garyakw said:
hi i have tried to dl the rom asi having the same prob but the file cannot be downloaded. is there any other way to get from you
Click to expand...
Click to collapse
If you are stuck on a HP Invent Screen, with G.39, etc.
And you have tried to hard reset and softreset with no luck, this is what you do.
XP Instructions:
1. Download this link http://www.mediafire.com/?3ygfbx0sjdy
2. In the taskbar area in the right hand corner, right click on activesync, bare with me, I'm using Vista and have to remember this, click connections..., you need to uncheck everything click ok or apply...
3. press ctrl-alt-delete, end process wscescomm.exe, (named something like that, end the process.
4. Extract the file you downloaded if needed.
5. Connect your device to the usb port on your computer.
6. Run Uni Exit Bootloader Application. Done
Vista Instructions:
1. Download these 2 links, and extract them if necessary.
http://www.mediafire.com/?3ygfbx0sjdy
http://www.mediafire.com/?9pmjkponfsg
2. Start Device Manager, (Start-Control Panel, Class View[Far Left Corner])
3. Connect HW6900 to USB port, you should now see a Mobile Devices (Next to + sign), Double Click
4. Right-Click on the Device, Click Update Driver Software, Choose let me pick from a list, Uncheck compatible hardware box.
5. Click have disk, Browse to location where USBAS is extracted, choose the wceusbsh.inf file, Double Click.
6. You should see Microsoft USB Sync, if not and it reverts back to the already installed file, and the box rechecks itself, uncheck it, choose microsoft, and choose the latest Microsoft USB Sync to install
GOOD LUCK
in reference to
Default bring back to life hw6945
i'we tried like you to upgrade radio part and a got an freezed phone
Solution for repair was flashing firmware with this program..
Download-Link #1: http://rapidshare.com/files/96527845...G_ROM.zip.html
its a no go here...
i get error 402.... times out and no can do.... what was that about german language... maybe i just need it spelled out. which screen does the unit need to be in. there is two... monochrome serial vs usb and there is the hp logo blue and white screen frozen indefinitely... please help i love this phone...
Hi, the rapidshare file is missing!
Could you give working link or send me the file to mail, please?
ipaq dude said:
Ok
I got it fixed, very simple solution
found it here
http://pdaphonehome.com/forums/hp-h...dowloaded-rom-update-ipaq-dead-need-help.html
Solution:
this is what I did to get this fixed.
1) Get the battery out of the iPaq, and wait for a few minutes while the "serial" image fades away slowly.
2) In the meantime, prepare your cradle, plugged into the AC charger and plugged via USB to your PC.
3) After a few minutes, with the screen of the iPaq completely gray, put the battery and battery cap back on (with our without SIM card), and put it on the cradle immediately.
4) The iPaq should start coming back to life, as if it were being hard reset. Let is stay on the welcome screen (i.e., do not tap it or anything).
5) Restart the upgrade process, it should proceed from there OK
Thank you to origianl solution provider
Click to expand...
Click to collapse
Man,r u sure the above can work well???? Confusing......I did the above like u indicated,but it's not work on my device HP6915,could u make it in details how u fixed the problem of updating ur device,thanks!
Regards,
Brose
Thanks, This help get me out of freeze
Thanks for posting this link. It brought my hw 6945 back out of the freeze. Stay away from HP's site update. Bad news
johnnynomadic said:
in reference to
Default bring back to life hw6945
i'we tried like you to upgrade radio part and a got an freezed phone
Solution for repair was flashing firmware with this program..
Download-Link #1: http://rapidshare.com/files/96527845...G_ROM.zip.html
its a no go here...
Click to expand...
Click to collapse
Thanks for UNIEXITBOOTLOADER thing, it makes my 6965 rocks again! Btw, could this file be used on other pdaphone such as O2 Atom? Thx b4.
Maybe
Most Likely Yes
bmw2320 said:
Thanks for UNIEXITBOOTLOADER thing, it makes my 6965 rocks again! Btw, could this file be used on other pdaphone such as O2 Atom? Thx b4.
Click to expand...
Click to collapse
cdguider said:
Most Likely Yes
Click to expand...
Click to collapse
I don't think so,Curtis.....But as I know most of dopod device hardly be dead....
Hello,
i have a problem with my hd. i am using energy rom latest version and i cant align my screen. the wizard keeps looping with the cross. i called the service and told me that i should install factory rom and that is not device problem. please advise
thanks
Alexis_vti said:
Hello,
i have a problem with my hd. i am using energy rom latest version and i cant align my screen. the wizard keeps looping with the cross. i called the service and told me that i should install factory rom and that is not device problem. please advise
thanks
Click to expand...
Click to collapse
did you press correctly on every "+" signs (total 5)? else it will repeat the same wizard again and again. another thing is try using stylus to press on the signs, more accurate.
else it could be corrupted rom flash. Did it happened before?
No it didnt happend before.....only when i flash a new rom. i press everything as i should
Go for another ROM. Cloudy maybe?
i will try it and i will let you know....thanks