Database Users

02 XDA mini s Screen Protection

Hi,
I've been using my xda for about a month now and have noticed it hard to keep the screen clean, it seems to be very greasy etc... Has anyone invested in a screen protector for this problem or is it not really worth it?
Also cause i have only had mine a month with limited use, has anyone who has owed this phone longer noticed it gets scratched from the pen etc after longer periods of time...?
I know not important questions but just something i've been wondering none the less. Thanks

Got a brando one
I wanted to ditch the case (as it's pants) so I got a brando screen protector. It was a real faff to fit and I still haven't got it a) square or b) without loads of [email protected] under it, but it does its job, it seems to be sensitive enough and I (probably) am too ham-fisted to judge how difficult it is to fit the thing.
Hope that helps.

I've been told the Martin Whatsisname Screen Protectors are really good.
I'm thinking about getting one of these.

Do they leave any marks when you peel them off afterwards? From the glue and stuff?

Hi Tom
They don't use any glue, so you can just peel them off with no problem.
They cling to the screen like clingfilm.

nothing else than brando! have used it on all of my previous devices .. just no comparison to the cheap ones on ebay ...

I would say screen protector is a must for me...I'm too lazy to pull out the stylus every time....a screen protector will allow me to tap with my fingers, nails.....or even a pen....in fact, I put a protector on almost every mobile phones, my previous PPC....

Fair enough, but at £8.50+ its a rip off!!! for a bit of plastic that cost 0.05p to make, they're laughing all the way to the bank....

Supply & Demand
Maybe. It's a quality product and it's still a lot cheaper than a new screen...
You pays yer money.

Maybe but im just not convinced, how can you decribe a bit of platic as a "quality product"? I have heard they are extreemly hard to fit properly without getting finger prints on them etc and you get air bubbles and it is really annoying if you even leave a few specs of dust underneath it...?
No one round the office here seems to bother with them. I dont expect with any device for the screen to remain untouched forever, i think it just comes down to normal wear and tear, as with everything. Just my views anyway, need to hear more about these things before i had over best part of £10.
I have seen a Martin Fields one and someone on here said they were good. Is it easy to notice its there if you have one installed?

I have bought some via ebay from screenprotector24 at £1.99 for 6 plus P&P. There was also a buy 2 get 1 free offer on too. I have never been a fan of screen protectors but I agree that with the Mini-S it is verging on essential.
I am more than happy with the quality of the ones I received.
Hope that helps someone.
Regards,
White.

I've been looking for some on ebay, what did you type in to search and find those? can you link me?

Hi,
Sorry, I'm at work and barred from ebay. www.screenprotector24.de may well work if I recall correctly.
Regards,
White

Brando screen protectors
Just because something's made of plastic doesn't mean it isn't quality. After all look at Pamela Anderson! (Sorry).
The Brando one I got is doing its job. Before I had the screen protector dirt would pile up and I'd be cleaning it 3 or 4 times a day. Now I don't have to. I was worried the screen would get damaged. I don't have to worry what I use on the screen or shoving it in my pocket.
Yes, you can tell it's on if you look. It looks like you've left the manufacturers sheet on but without a tab to remove it if it catches the light. Straight on, you'd be hard pressed to know it's there - honest.
I haven't seen the cheapo ones myself, I went on recomendations on forums from people who had more experience.
Also, Brando service is outstanding in my experience.

Right ok, i am thinking of getting one just for peace of mind. All i can find is Martin Philips ones on UK sites... Where can i find a decent priced Brando one on a UK site for a 02 xdx mini s? Can someone name a shop or link me etc?
Thanks

Go straight to the source!
I bought mine direct from the Brando site in Hong Kong... http://shop.brando.com.hk/screenprotector.php. It arrived within 6 days
I had the antireflective one on my old XDA2, but these ultra glossy ones are MUCH better. It was a fiddle to fit, but I honestly can't that it's there other than by looking for the edge. I've tried this a few times and I find the following procedure works well.
First off, you need to find as dust free an environment as possible. Choose a room that doesn't have any carpet, or fabric in it if you can(cushions curtains etc). Boil a kettle, and make the room a bit steamy. When the steam clears, it should take some of the dust with it.
The trick to avoiding dust is to be prepared. Get a good lint free cloth (lens microfibre cloth worked well for me) and a blower brush - small rubber bulb with a nozzle. Also keep some masking tape ready. Finally you will need a bright light - ideally a spot light, or if you've got low fluorescent lights under over your kitchen work tops, they are ideal. Wear latex gloves if you have any (you can usually get packs of 20 from poundland)
Stick some masking tape to the your worksurface, folding it back on itself, so that the sticky side is facing up. Use several strips so that you have an area two or three times the size of your screen.
Spend a few minutes polishing with the lint free cloth, and then set the phone down, face up, well illuminated (from above) and switched off!. Blow off all the remaining dust with the blower - make sure that no dust is stuck (might require more polishing) at this stage you have two hands free - in a minute you won't! Dont worry if some dust starts to settle back on the screen at this stage - it will be loose, and you can blow it off in a minute.
Next step - take the screen protector, and peel off the backing two thirds of the way. Keep the 'sticky' side face down so dust doesn't settle on it. It's helpful if you can crease the backing slightly as it's quite springy and tends to get in the way a bit. Be careful not to touch the exposed side though. If you're right handed you'll want the screen protector in your right hand at this moment.
The next bit, you might need to repeat a few times until you get it right...
Blow the last bits of dust off the screen (do NOT use your mouth - you will spit all over the screen). Line up the most exposed end of the protector - its a very precise fit, the edges will touch both sides, and the end should be lined up exactly with the end of the screen. If you push the protector under the plastic above the screen it will be short at the other end. You might need to lift and reposition a few times to get this right. Once you have placed the exposed end, put a finger on top and check the alignment. Now check for any dust. You might be able to blow one or two bits off, but if there is more than that, you need to lift off the protector, press it down onto the upturned tape to get rid of any dust, blow the dust of the screen and try again. The dust sticks to the tape MUCH better than the screen, and will not leave any residue on the Brando protector, so you can do this quite a few times if necessary.
The important thing here is not to panic. You will get dust, and will need to go round the loop a few times, but as you'll be prepared, there will be no problem. Once the protector is lined up, the screen is (temporarily) dust free and there are no bubbles (phew!) carefully remove the last of the backing film and holding the edges very lightly between your fingers (gloves help here) lay the last bit removing any bubbles. Once down, it is hard to get the protector off without damaging the edge so only do the last bit once you're sure there is no dust/bubbles.
Remove the front sheet and polish. With any luck, you should hardly be able to tell that the screen protector is there!

Thanks for those really comprehensive instructions! I'm going to order one from the Brando site today and will pick up the blower and lint-free cloth etc from Jessops (camera shop) this weekend.

Martin Fields overlay plus Question
Nice one on such detailed instructions!
I order a Martin Fields over lay plus today, they seem to have good reviews everywhere i have looked. They are slightly adhesive though, but as this is a "gentle silicon based glue" (so i hear) i think that means it will be fine on the screen.
Has anyone had experience on using these and what the screen is like after you remove them, any residue etc left afterwards? How long will it last roughly?
Thanks for any help guys!

I haven't tried this, but you could probably save yourself the cost of a blower brush by using a bike pump or better still an airbed footpump (you can use that one handed).

tom99, if you get a Martin Fields protector (or any other sort that uses adhesive) I'm not sure that its safe to use masking tape to clean it. The Brando ones stick to the screen electostatically, so its safe to clean them with tape (the instructions that come with it recommend scotch tape). If the instructions you get with your Martin Fields protector don't mention cleaning with tape, then I would miss out that step. Can you add a comment to this thread when you get it (or anyone else that has used a MF protector)? It might help others decide which protector to go for.

Another case thread...Slimmest Kaiser Case?

Well there seems to be a lot of views about the best cases out there, just wondered what the most 'pocket friendly' case was?
Don't care about the material as long as it isn't a sock or a stick-on option (ie an actual case)
Definitely no belt loop, preferably a very low profile clasp etc...
Basically just want something that is likely to stop it getting scratched up in a bag or if it was dropped, but don't need full armour!
Any good suggestions?

I've been looking for something pocket friendly as well... I'm almost ready to just get a thin sunglass pouch... currently I'm using a case for a Sprint Mogul, but it has a belt clip...

i use an ipod slip case, and have pulled off the belt clip, gives good protection to the screen,
going to order a leater slip case from www.pdair.com to see what thats like

I've got one of these - http://www.pdair.com/catalog/product_info.php?cPath=10100000_900000_11000164&products_id=6561
Doesn't add much to the size at all, and I keep mine in my pocket all the time.

Here is what I'm using, it comes in Black, Brown or Pink:
http://www.wirelessground.com/tiltflipblack.html
It covers the back and front very well, the cut outs are aligned very well, it has a slimmer form factor than the Krussel Orbit I normally use.
Here is the one my spouse uses, it comes in Black or White:
http://www.boxwave.com/products/dlsleeve/at_t-tilt-designio-leather-sleeve_2906.htm

I just ordered one of these yesterday. I will let you know how it is hopefully tomarrow or over the weekend.
http://cgi.ebay.com/Smoke-Protector...ryZ15036QQssPageNameZWDVWQQrdZ1QQcmdZViewItem

SpeedRazr said:
I just ordered one of these yesterday. I will let you know how it is hopefully tomarrow or over the weekend.
http://cgi.ebay.com/Smoke-Protector...ryZ15036QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
Click to expand...
Click to collapse
i would be interested in your opinions and if you could confirm these points for me:
1) Can you still use the touch screen?
2) If the slide up and tilt works fine with the case on
3) The general quality and how bulky it is in a pocket
this looks perfect for me as i wanted a 2 piece armour case where i could still slide open the phone

scharnet said:
Here is what I'm using, it comes in Black, Brown or Pink:
http://www.wirelessground.com/tiltflipblack.html
It covers the back and front very well, the cut outs are aligned very well, it has a slimmer form factor than the Krussel Orbit I normally use.
Here is the one my spouse uses, it comes in Black or White:
http://www.boxwave.com/products/dlsleeve/at_t-tilt-designio-leather-sleeve_2906.htm
Click to expand...
Click to collapse
The "tiltflipblack" is made by PDair and is available for 1/2 that price. I've had one for several weeks and it still looks new, and I wear it every day. It's the perfect case for me.

The slimest most "pocketable" case I've found yet, is the formfitting Noreve case as seen here:
http://www.pocketpcfreak.com/archive/00006945.htm
It is also one of the very few - true - formfitting cases (using a laminated leather design, w/o the ugly and disturbing plasting cover over the KB. It protects the front and back really well, if not so much the sides. Easy to use and good workmanship.
Actually it IS meant (IMO) for pocket carrying.
Have it for about a month, still looks as new. If however looking for a drawback, then to my daily use pattern there is one. While in the case using the Kaiser/Tilt for navigation (in a cradle) needs taking it out of the case.
======
Saar

I've tried several ...
Tothotspur said:
i would be interested in your opinions and if you could confirm these points for me:
1) Can you still use the touch screen?
2) If the slide up and tilt works fine with the case on
3) The general quality and how bulky it is in a pocket
this looks perfect for me as i wanted a 2 piece armour case where i could still slide open the phone
Click to expand...
Click to collapse
Just wanted to add my comments based on owning 4 different cases for the Tilt/Kaiser ...
The PDAir aluminum cased is good and pocketable. It is a little on the heavy side, but I've carried it arond now for a couple of weeks and it's all right. The downside is that there is a hard plastic protector over the touchscreen of the Tilt. You have to open the case to use the touchscreen or you have to take the hard plastic out. You can either cut out or push it out with some force, but the plastic is glued in and is under the neoprene that cushions the Tilt against the case. Not the smallest feel in the pocket, but no leather covered cardboard bulk feel. The size of this reminds me of a naked 8125 in my pocket (did that without disaster for almost 2 years).
I also tried the PDAir leather flip case. That one is definitely not pocketable unless you have some REALLY big pockets. And I'm not a big flip cover guy. Another strike is the plastic keyboard cover.
I also tried the Noreve and it's a nice leather case. I would consider this one pocketable, it's rather slim. But it has the flip cover. The good thing is that it has no plastic keyboard cover. It's a little loose when you close the cover with the snap. It's not loosely held in ... that's a good fit. But the snap doesn't hold the flip cover down as firmly as I'd like.
Lastly, I JUST snapped on one of the plastic snap-on kind. Good fit, but not sure how much the plastic will help in a fall. It snapped on tightly ... so tightly it took 15 minutes to get it off! I did not like that at all. If something goes wrong and you need to drop the battery quickly ... 'quickly' won't happen with this case. You can still use the touchscreen and it's a very tight snap on fit. Doesn't add much bulk or weight for pocket storage. NOTE: if you pick one of these up, be careful and check whether the belt clip button on the case is screw on or permanent. The permanent ones won't be pocketable.
The best feel in the pocket is the plane Tilt/Kaiser with no case. But I know I'm pushing my luck if I continue to do that. Still switching up to see what I end up liking most. Hope this info helps folks.

Tothotspur said:
i would be interested in your opinions and if you could confirm these points for me:
1) Can you still use the touch screen?
YES!
The openings for the keypad and LCD are tappered to provide the best access to the edges but they become alittle harder to get at due to the thickness of the plastic.
2) If the slide up and tilt works fine with the case on
Yes the screen slides out and up to the normal position. The upper softkeys are silightly harder to get at when tilted due to the tickness of the plastic.
3) The general quality and how bulky it is in a pocket
Fit was tight, and snapped into place. I do not plan to use the clip as it is optional, but I will follow up with a proper review and test it out. I will get exact mesuraments later but it is not a big change and well worth the extra size.
this looks perfect for me as i wanted a 2 piece armour case where i could still slide open the phone
Click to expand...
Click to collapse
Yup! Cheap Too!
I will follow up with a better review tonight.

What I do not understand about using the transparent plastic snap, is why the hack would one need a case at all when all the really "pocket sensitive" components (Touch screen, Camera lens) are not covered at all... IMO if one is indiferent to this, they may not need a case at all.
I guess that all cases are kind of trade offs. Whatever protects adds bulk in the zones protected, light protection protects less than heavy armor but presents snappier use and so on.
The potentially best solution I've seen yet is actually not offered for the Tilt/Kaiser. It is made by EB Cases and called the eNovo. It is made of sturdy yet thin laminated leather, offering a form fitting case with an optional leather flip.
http://www.ebcases.com/-strse-3333/eNOVO-PAQ-6500/Detail.bok
I'm trying for some time to convince EB, Noreve and BoxWave (the ones apparently having the technology) to think about it...
Cheers,
======
Saar

thanks kahibbi and SpeedRazr for your input, i look forward to your review

SpeedRazr said:
I just ordered one of these yesterday. I will let you know how it is hopefully tomarrow or over the weekend.
http://cgi.ebay.com/Smoke-Protector...ryZ15036QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
Click to expand...
Click to collapse
I picked this up from DayDeal.com and it didnt' fit my ATT tilt. the back does but the front will not stay on
i picked up the alum. case for travel and biking it is perfect. also from DayDeal

Body Glove Case Issues

Anyone else buy and have problems with it? I searched around after thinking I saw a complaint on it like I've got but couldn't find.
Basicly, I put it on started noticing the top was putting pressure onto the screen I think. THe touch screen got extremely laggy, unresponsivess, and just seemed to go crazy. I'm going to try sanding it down on the inside but I think that just sucks.
On top of that the phone fell out of the back/belt clip half one night and caused a nice freakin dent in my phone and allowed the battery to flip out almost down a sewer.
Anyone care to give me a positive review so I don't just throw this thing out?
Also - is it possible to buy a new physical case to replace a scratched/dented case? Not the body glove I mean the actual phone casing.

chibahawk said:
Anyone else buy and have problems with it? I searched around after thinking I saw a complaint on it like I've got but couldn't find.
Basicly, I put it on started noticing the top was putting pressure onto the screen I think. THe touch screen got extremely laggy, unresponsivess, and just seemed to go crazy. I'm going to try sanding it down on the inside but I think that just sucks.
On top of that the phone fell out of the back/belt clip half one night and caused a nice freakin dent in my phone and allowed the battery to flip out almost down a sewer.
Anyone care to give me a positive review so I don't just throw this thing out?
Also - is it possible to buy a new physical case to replace a scratched/dented case? Not the body glove I mean the actual phone casing.
Click to expand...
Click to collapse
I have this case and had the same problem. I have read that many others have had it too. Honestly I dont know why a company would put out a product like this. They all should be recalled, however me being me decided to just fix it by Taking a dremel tool and shaving some of the inside part of the screen protector off, making it put less pressure on the screen. It fixed it immediately. The case does a great job in protecting the phone, just a major flaw that can be fixed if you have the time and tools. If you dont, ***** to the company and get your money back and try something else.

Praygo said:
I have this case and had the same problem. I have read that many others have had it too. Honestly I dont know why a company would put out a product like this. They all should be recalled, however me being me decided to just fix it by Taking a dremel tool and shaving some of the inside part of the screen protector off, making it put less pressure on the screen. It fixed it immediately. The case does a great job in protecting the phone, just a major flaw that can be fixed if you have the time and tools. If you dont, ***** to the company and get your money back and try something else.
Click to expand...
Click to collapse
Yes I could see that the inside casing was a bit rough so sanding should stop the problem - but seriously that's a major issue.
Have you found that it holds the phone well though? Because I'm very upset that my phone fell out of it once already but maybe it was an error on my part and it wasn't secure enough...

I've never had the phone fall out of the body glove case.

i mangled my body glove case.
someone bumped into me and the phone fell out of the case AGAIN.
i ripped it to shreds and left it on the side of the road to rot into plastic hell.
i dont recommend this product.

I returned mine. I had the exact same issues (screen and phone falling out). It also didn't attach properly on the top left corner, it was always bowed out. I don't recommend it either.

Anyone got any else to share?
I was THIS CLOSE ( || ) to buying it. lol
Is there anything out there that's similar to it in design, but better?

returned
When all the way snapped on, mine pushed the top left corner so hard the entire screen would not respond to touch. Returned it.

My friend and i had the same issue. We just took it off messed around with it and put it back and it works fine, SOMETIMES it happens again but we just take it off and put it on.
Since there is not any other case that provides this type of protection we are keeping it. I rather my phone be safe than anything else.

I just ordered mine yesterday so I'm anxiously awaiting its arrival.
What exactly did you have to mod to get it to work? According to my readings, you just need to sand down the edges that connect with the screen right?

I may just buy the case and sand down what was mentioned. I like the design of the case..only one so far I really like.

I've been using one for about two weeks and am very happy with it. Had read about the screen pressure issue on other posts (searching helps folks), and scraped down the top corners before I put it on. Don't need a dremel tool or sandpaper. No problems, fits perfectly. The only warning is that it's a little dicey to take off once it's on -- it really fits snugly.

Yout're talking about the "sand texture" clip-on case, right? If so, yes, I bought the case too. The top cover was too tight and caused the screen issue people are mentioning. That was an easy fix by shaving down the edges that were pressing too hard (actually, I just cleaned off the coating from the plastic that was causing it... The bottom of the case however wouldn't fit at all. no matter what I tried, I couldn't get all of the clips to lock over the edges of the phone. I removed the felt lining and still had issues. I got around it by using thin double sided tape (for a temporary fix until I got a new case). I wouldn't trust the belt clip with the double stick tape though. I ordered the rubberized case on ebay and the fit is perfect. Just get that one. I sent an e-mail in to Body Glove and have had no response yet. We should all get our money back on these cases, or at least a redesigned bottom case that fits correctly. Right now it was just a complete waste of money. It's a shame, because I really liked the feel of the case.

Torkrench said:
Yout're talking about the "sand texture" clip-on case, right? If so, yes, I bought the case too. The top cover was too tight and caused the screen issue people are mentioning. That was an easy fix by shaving down the edges that were pressing too hard (actually, I just cleaned off the coating from the plastic that was causing it... The bottom of the case however wouldn't fit at all. no matter what I tried, I couldn't get all of the clips to lock over the edges of the phone. I removed the felt lining and still had issues. I got around it by using thin double sided tape (for a temporary fix until I got a new case). I wouldn't trust the belt clip with the double stick tape though. I ordered the rubberized case on ebay and the fit is perfect. Just get that one. I sent an e-mail in to Body Glove and have had no response yet. We should all get our money back on these cases, or at least a redesigned bottom case that fits correctly. Right now it was just a complete waste of money. It's a shame, because I really liked the feel of the case.
Click to expand...
Click to collapse
Could you give us the link for the ebay one please!

http://cgi.ebay.com/NEW-RUBBERIZED-...5|66:2|65:12|39:1|240:1318|301:1|293:1|294:50
That is the one I ordered, and the fit is perfect. The only thing I wish it had was the belt clip insert for the case included. I don't know where to find one, but I mostly keep it in my pocket anyway.

you guys want a good case that protects? check out the monaco aluminum case, it comes with a clear lens on it which I haven't removed but you could if you wanted quick access to the touchscreen. I work in the construction field and have yet to have it fall off my clip. I also dropped my tilt (when I used it) from about 8" off a ladder and it was perfectly fine. The aluminum case for the fuze isn't any more bulky than the body glove case either.

bilbobrian said:
check out the monaco aluminum case
Click to expand...
Click to collapse
I've got one of these as well...and while it does protect the phone very well it will also lower your signal strength. I've had these type cases for the Wizard and Tilt and now the Fuze...whenever I'm in an area where the signal was a little iffy to begin with I WILL either drop the call or be unable to answer with the metal case. So, stay away from the aluminum ones if you go into lower coverage areas (and no...the slots they cut in the back to help improve the signal don't actually help.)

Seidio Innocase Surface Case - Pictures??

Has anybody purchased the Seidio Innocase Surface case?? Could you post some pictures?? I'm debating if I want it or not, but one picture on their website really doesn't show how thick it really is on the phone. Also looking at opinions if you have it on your Touch Pro/FUZE. Thanx.

I should be ordering the case this week. I'll let you know.

RallyPunx said:
Has anybody purchased the Seidio Innocase Surface case?? Could you post some pictures?? I'm debating if I want it or not, but one picture on their website really doesn't show how thick it really is on the phone. Also looking at opinions if you have it on your Touch Pro/FUZE. Thanx.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=461936
That thread has links to the Seidio site, which has pictures of the case from different angles.

More specifically...if you go through this link and "mouse over" the picture of the case, it'll magnify the area:
http://www.seidioonline.com/ProductDetails.asp?ProductCode=CSR2HTFE-BK
If you actually click on the picture, it will take you to this page, which has a few different angles.
http://www.seidioonline.com/PhotoGallery.asp?ProductCode=CSR2HTFE-BK

I saw those pictures on the website, but you can't really see the area around the screen very much to see how deep the screen is with the case on. I don't use the stylus much and I think if the case is too thick, I will have trouble hitting the corner buttons (start, calendar, contacts) with my finger. Any thoughts?

D3TH METAL said:
I should be ordering the case this week. I'll let you know.
Click to expand...
Click to collapse
Please also let us know how well this case works for you. There is a similar type of case for $10 on ebay which causes a phone lockup due to improper fit around the screen:
http://forum.xda-developers.com/showthread.php?t=459761
The problem rears its ugly face usually after a couple days of use...
I'd be willing to pay 3x for a case that actually works!
thanks!

jknuckey said:
Please also let us know how well this case works for you. There is a similar type of case for $10 on ebay which causes a phone lockup due to improper fit around the screen:
http://forum.xda-developers.com/showthread.php?t=459761
The problem rears its ugly face usually after a couple days of use...
I'd be willing to pay 3x for a case that actually works!
thanks!
Click to expand...
Click to collapse
I honestly don't see how any of these cases would work better than the ebay one. I had the BG one which actually is worse than the ebay unit. The ebay unit I have has been fine for more than a few days. It has to do with the flush screen of the FUZE so any excessive pressure against the screen would render the screen inoperable over time. BUT without the pressure/tension, there would be play once the upper piece is snapped on.
There isn't really much room to do this due to the flush screen IMHO.

I bought a similiar case from Brando. It is clear plastic instead of black. It works well and there was another thread about it here. It just blocks the PTT button on the Fuze. Ive used it for a month and it works fine, no screen problems. Only problem for me is one of the tabs came off, but it still stays on nice and sturdy. Its adds quite some thickness to this already thick phone.

I switched to the Innocase w/ holster about 1 week ago from the Body Glove 2-pc Snap Case. I like both:
The Body Glove is built like a Brick S--- House, has a very nice non-slip finish that actually matches a resident wallpaper. The phone is very safe in this case however, its a pocket carry, no belt clip.
The Innocase is half the thickness of the Body Glove. It fits like 2nd skin and has a silky feel and seems to be a bit slippery. The holster at 1st glace scared me. Thought the phone would pop out but I have found after a week of use, its just fine and very handy. The clip that holds the phone is spring loaded and can be locked to keep the phone from being removed if needed. The only problem I see is for those of you who wish to holster your phone and listen to music with a wired connection. The Headphone jack is slightly obscured by the Lock clip of the holster. Nothing a Dremel tool couldn't fix very quickly.
As stated, I like them both but use the Innocase as my daily protection. If I find myself exposed to rougher conditions, my choice is the Brick S--- House case from Body Glove. Both fit like second skin.

anyone have this case for the htc fuze?

http://cgi.ebay.com/FR-HTC-FUZE-TOU...5|66:2|65:12|39:1|240:1318|301:1|293:2|294:50
will this fit a att fuze?
looking for a rubberish case for my fuze. i have a bodyguardz screen on it..but its not as good since the edges are catching dirt

Sucks. Cheap, wouldn't reccomend. Try a hard rubberized case... you can find em on ebay easy.

Hyett1 said:
Sucks. Cheap, wouldn't reccomend. Try a hard rubberized case... you can find em on ebay easy.
Click to expand...
Click to collapse
links to said case?

AT&T sells a hard/rubberized case for around $25, but I strongly recommend against using them. As much as I hate carrying around a phone without a case, I have all kinds of issues with screen sensitivity whenever a snap-on case was on my Fuze.
Pressing on the top corner of the case would activate the Start Menu, the edges of the screen would become less sensitive... to the point of actually needing my stylus.
In addition, the nubs on both halves of the case press against each other, and actually separate the phone a little bit.

NotATreoFan said:
AT&T sells a hard/rubberized case for around $25, but I strongly recommend against using them. As much as I hate carrying around a phone without a case, I have all kinds of issues with screen sensitivity whenever a snap-on case was on my Fuze.
Pressing on the top corner of the case would activate the Start Menu, the edges of the screen would become less sensitive... to the point of actually needing my stylus.
In addition, the nubs on both halves of the case press against each other, and actually separate the phone a little bit.
Click to expand...
Click to collapse
One more thing to add to NATF's message....
Hard snap on cases scratch the hell out of the sides of the phone. Tried a few diff ones and not ONE left the oem case intact. I think its because sometimes dust gets between the case and the hard case and scratches it up. I just use a screen protector and a leather carrying case these days.

pyraxiate said:
One more thing to add to NATF's message....
Hard snap on cases scratch the hell out of the sides of the phone. Tried a few diff ones and not ONE left the oem case intact. I think its because sometimes dust gets between the case and the hard case and scratches it up. I just use a screen protector and a leather carrying case these days.
Click to expand...
Click to collapse
Same here. Actually, since AT&T didn't release a leather pouch for the Fuze, I'm still using the one from my Tilt.

The Seido hard innocase it super thin, does not scratch the fuze at all, and is worth the money.

antok86 said:
http://cgi.ebay.com/FR-HTC-FUZE-TOU...5|66:2|65:12|39:1|240:1318|301:1|293:2|294:50
will this fit a att fuze?
looking for a rubberish case for my fuze. i have a bodyguardz screen on it..but its not as good since the edges are catching dirt
Click to expand...
Click to collapse
I have this exact case and have been using it since I got the Fuze. I have the other case as well, still sitting in plastic.
I had to make a mod to mine. The usb mini sync/power cable didn't fit right, so I had to trim a little there.
I like this case. Plenty of protection, for both the screen and the button/d-pad area on the bottom. Not the most attractive case, but works very nicely for a soft rubber case.
Just my .02

I used to use this exact same case but didn't like it. Like previous poster mentioned the charger port is kinda blocked off but a lil alteration helped fix that. The biggest problem i had was how it attracted dust and lint way too easily which really made it look bad.