hi
I have xiaomi mi note 2 and updated this device .
but bluetooth not working after update A few months ago.
and wifi not working after new update . this update receive OTA
bluetooth is turned on but not detect any device.( in hardware test has mac address )
wifi is turned on and detect any wireless device but not connect to these devices.( in hard ware test has mac address and detect any devices)
i reset factory and full wipe . change rom by global , stable , developer , china , europe , custom ,.... but not solve this problem
PLEASE HELP ME .
You can try to install the global stable with fastboot.
Before doing this , make a backup because this will erase your entire storage.
I think you need to have adb and fastboot installed on your PC , not sure.
Download the fastboot rom from here: http://en.miui.com/a-234.html
You can find it in the fastboot method section.
Unzip the archive and double click on flash all.bat
Put your phone into fastboot mode and plug it in.
It should take a while , so relax.
It should close the console when it's done , if i'm not wrong.
Boot into the os and test wifi and bluetooth now.
Hope this will help , this is all i can say that it might work
ok . thank you for reply
I used these ways and not working in my device .
my phone should repair and change wifi and Bluetooth IC .
wifi and Bluetooth IC in my phone is ruined and should change by another IC
I haven't good news for you, probably motherboard it's broke. WiFi and Bluetooth it's first symptoms. My tip, try found mi note 2 with broke OLED, motherboard is cheaper than display.
Related
Hey guys i've Hard Bricked my Yureka. Phone Doesnt turn on nor goes to fastbooot, instead is only detected in windows as Qusbs-Bulk. Please help ME
Follow the steps shown in link below;
https://cyngn.com/support/
http://forums.yuplaygod.com/threads/factory-images-and-flashing-tools-official.2178/
But my phone does not boot into fastboot
Search at play god forum, there are some procedures given there which may solve your prob. http://forums.yuplaygod.com/threads/help-completely-bricked.4641/#post-45794
HI thanks for help but in all above cases they were soft bricked ..i.e their phones booted in fastboot but mine isnt.
Hmmm ... seriously worried situation haan. {Kiya kya tumne}
If you can tell us what exactly you did, may be then we can help.
I also hardbricked when i tried to port MIUI. But i got replaced by YU without any cost and within 3 days
Exactly me too flashed miui of f2 without boot.img..Was trying to port...
@ Suhas Is the new phone same as old one or a used one??
suhas.holla said:
I also hardbricked when i tried to port MIUI. But i got replaced by YU without any cost and within 3 days
Click to expand...
Click to collapse
I also hardbricked when i tried to port MIUI, Now waiting for the repacement.
Called them and raised the ticket 6 days before, but they are yet to dispatch.. . . . Very frustrating !
Do you have any information on how to unbrick. I searched much but wouldn't find files to unbrick !
1. 8939_msimage.mbn
2. MPRG8939.hex
3. rawprogram0.xml
4. patch0.xml
Hope some one comes to rescue me :crying:
Video Tutorial HOW TO UNBRICK YUREKA
Srry i cant post the youtube link as i am new here
Just go to youtube
Search kanwal deep unbrick yureka
And watch the video
To go in fastbool mode remove battery insert again and press vol up while connecting usb
quakze said:
I also hardbricked when i tried to port MIUI, Now waiting for the repacement.
Called them and raised the ticket 6 days before, but they are yet to dispatch.. . . . Very frustrating !
Do you have any information on how to unbrick. I searched much but wouldn't find files to unbrick !
1. 8939_msimage.mbn
2. MPRG8939.hex
3. rawprogram0.xml
4. patch0.xml
Hope some one comes to rescue me :crying:
Click to expand...
Click to collapse
ahh Same situation I too searched for that files when i had bricked my device
Since the chipset is new. So not able to find
suhas.holla said:
ahh Same situation I too searched for that files when i had bricked my device
Since the chipset is new. So not able to find
Click to expand...
Click to collapse
I have got rom of Huawei C199s (MSM8939), which has many file packed into UPDATE.APP.
I have unpacked it, but the file name and extensions are unknown.
At present I am trying to identify the msimage.mbm and mprg files.
The rom link is http://www.needrom.com/wp-content/uploads/2015/03/C199s-V100R001C92B260-Telecom.zip
Shrihari007 said:
Hey guys i've Hard Bricked my Yureka. Phone Doesnt turn on nor goes to fastbooot, instead is only detected in windows as Qusbs-Bulk. Please help ME
Click to expand...
Click to collapse
ask for replace in customer care. as they told they will replace your mobile even after unlocking boot loader, root.
my device also gone hard bricked not get into the fastboot mode..
and no customer care no. to contact not correct > this one 18602122122
any help
thnks..
You guys can take a look at this thread -
http://forum.xda-developers.com/yureka/help/question-qualcomm-download-mode-k-t3068040
Hit thanks to the creator and me if helped.
suhas.holla said:
I also hardbricked when i tried to port MIUI. But i got replaced by YU without any cost and within 3 days
Click to expand...
Click to collapse
What did you tell the customer support about your phone getting bricked.
I tried calling the support, but they said that they will chargers. 3000 for replacing .
please help
my device got bricked 2 days ago and now there is no fastboot mode and not even the led lights showing up if the device is connected to the pc!! and whats even worse the cc is not picking up the calls
my mobile also hard bricked.
suhas.holla said:
I also hardbricked when i tried to port MIUI. But i got replaced by YU without any cost and within 3 days
Click to expand...
Click to collapse
hi.... my yu yureka also get hard bricked after installing lollipop update from yu.. please tell me the steps you followed to replace your yureka...... please reply fast...
:crying::crying::crying:
issue regarding in functionality in yu yureka after upgrading with lpllipop
dear sir,
my name is anurag. i am using yureka ao 5510 phone after launching official update for phone i upgrade my phone.
i faced sevral problem after updating. the list are provided below.
1) overheating device than normal one while comparing with kitkat.
2) automatically turned off and un- responsive and on screen multicolor circle appeared wih cross over circle, its upto 5-6 hrs after that suddenly screen appeared after turning on mobile and start working.(in this process sevral times i remove battery & reinsert and trying to start it normally).
3) when phone connecting to wi-fi hotspot network (apple tablet over 3g) and i am trying to update apps from playstore its not updated(google play services unfortunately stopped) over wi fi network, but its working good on mobile data.
4) now currently issue in brightnesss control and in setting < storage option < USB computer connection the checkbox option are not apperared & phone not connected to computer(using windows 8.1 ),
please kindly fix this buges...
and provide some patch or system updates as earliar as possible to overcomethis issue.
Hello, I have redmi 3s 32GB , I have had developer rom and last friday as a many of you my phone was not able to be used, so I tried to flash global stable rom via fastmode commands, but phone was bricked, so I removed back cover and reset pins,of course reconnnected battery, after this phone was detected in win10 and I have installed global stable rom, pc now detect phone as redmi 3s, I saw my internal sdcard...but screen is still blank, I cannot see recovery boot, fastboot and no logo too. Could you help me? Is screen broken or is this software problem?
Regards
undulus said:
Hello, I have redmi 3s 32GB , I have had developer rom and last friday as a many of you my phone was not able to be used, so I tried to flash global stable rom via fastmode commands, but phone was bricked, so I removed back cover and reset pins,of course reconnnected battery, after this phone was detected in win10 and I have installed global stable rom, pc now detect phone as redmi 3s, I saw my internal sdcard...but screen is still blank, I cannot see recovery boot, fastboot and no logo too. Could you help me? Is screen broken or is this software problem?
Regards
Click to expand...
Click to collapse
Hi, open ur phone again and check the display connector, try fully disconnecting it and reconnecting it and check if all other connectors in range are also properly connected. Then reassemble ur phone.
Next time, do not open your phone unless you really have to. I don't see why you have opened to reset it. You can press power for very long then after maybe 30 seconds or so, your phone will fully turn off. No need to open it for that.
Next time if you have a question, use the Q&A section, not this one. You'll get answers quicker there too.
Bricked or screen is broken
Without disassembling I was not able to detect my phone, after pin reseting phone was identified in windows. No recovery boot was working too... This is reason why I disassembled phone...
But thank you for reply..
undulus said:
Without disassembling I was not able to detect my phone, after pin reseting phone was identified in windows. No recovery boot was working too... This is reason why I disassembled phone...
But thank you for reply..
Click to expand...
Click to collapse
if that worked, i'd be curious to know
Hi master , I have a problem after flashing via adb, There is a description (skip the GPRS modem) on the log. so after hh starting signal does not come out. but APN settings mode detected on the card that I used :crying: . I have been doing a lot of flashing starts from via adb to use AsusFlashTool and via the updater, but remains the same signal does not work. Please help me :crying:
im using this rom UL-ASUS_T00F-WW-3.23.40.52 on Asus Zenfone A500CG
AiimTuanaya said:
Hi master , I have a problem after flashing via adb, There is a description (skip the GPRS modem) on the log. so after hh starting signal does not come out. but APN settings mode detected on the card that I used :crying: . I have been doing a lot of flashing starts from via adb to use AsusFlashTool and via the updater, but remains the same signal does not work. Please help me :crying:
im using this rom UL-ASUS_T00F-WW-3.23.40.52 on Asus Zenfone A500CG
Click to expand...
Click to collapse
Check if baseband and IMEI number is missing ?
Hello , ive been facing this problem since 2 days ago working day and night to fix it and i didnt found a way to do it.
All started with a Hard brick that detected the device as Diagnostic 900E i did a test point and solve it so easy, then i installed a rom a android 8.0 rom and here is where the problem begun.
It looks like it was all perfect i started with the initial configuration, but when it went for select the wifi the phone reboots all the time. I tried to skip every config and managed to get on the sistem but then it reboots over and over every 1 or 2 min the phone reboots by himself. I flashed a lot of roms and none of them works , wiped everything from normal recovery and twrp and nothing. Does anyone has any info of this issue? A friend of mine who also bought a mia1 had the same problem and he dosn't even knows how to flash a rom...
Also i know is not a batery issue because the phone wont reboot on Recovery or either fastboot mode for hours...
Here is a video so you can see what i'm talking about.
https : / / drive . google . com / file / d / 1gpPkLcR -HJIhEhB46JZ4voMWnQcbQdiU / view ? usp = sharing
scriiby said:
Hello , ive been facing this problem since 2 days ago working day and night to fix it and i didnt found a way to do it.
All started with a Hard brick that detected the device as Diagnostic 900E i did a test point and solve it so easy, then i installed a rom a android 8.0 rom and here is where the problem begun.
It looks like it was all perfect i started with the initial configuration, but when it went for select the wifi the phone reboots all the time. I tried to skip every config and managed to get on the sistem but then it reboots over and over every 1 or 2 min the phone reboots by himself. I flashed a lot of roms and none of them works , wiped everything from normal recovery and twrp and nothing. Does anyone has any info of this issue? A friend of mine who also bought a mia1 had the same problem and he dosn't even knows how to flash a rom...
Also i know is not a batery issue because the phone wont reboot on Recovery or either fastboot mode for hours...
Here is a video so you can see what i'm talking about.
https : / / drive . google . com / file / d / 1gpPkLcR -HJIhEhB46JZ4voMWnQcbQdiU / view ? usp = sharing
Click to expand...
Click to collapse
Bro you chooses wrong script in mi flash
That deleted your imei
Give me your whatsapp or telegram for furthe discussion
I guess I have the same problem maybe i don't have an imei anymore, I should check :
https://forum.xda-developers.com/mi-a1/help/help-stucked-weird-bootloop-flashing-t3721142/page3
https://forum.xda-developers.com/mi-a1/help/mi-a1-imei-help-please-t3742245
https://forum.xda-developers.com/mi-a1/help/ruined-modem-partition-please-help-t3733909
go through this threads bro, you will revive your device for sure good luck mate
Bro persist partition repair fixxed restart problem
Have you solve this?
Write persist in twrp... Search the forum for the persist and guide...
For me writing persist didnt work till i had to switch from slot A to slot B in twrp then phone booted
Hi
I have an old Mediapad M3 lite 8" with stock rom .
Yesterday after a full discharged battery, I put it in charge and start it , after 1 hour I turned on it and it goes in loop with huawei logo continuously .
Well .... I decided to do an hard reset, entered in recovery mode and did a full wipe to recover it .
The procedure was done, the tablet start and tell me as usual questions, language, google account, wifi etc .... it starts to install the last google backup found, this for a couple of minute when it turned off for ever .
Now is not possible to turn on it, not power on, not possible to enter in recovery, nothing , I tried also to disconnect battery hoping in a reset but nothing changed .
What do you suggest to do ???
In this moment if I connect it to my PC I see only the Qualcomm HS-UB COM port .
If I remember well there is a procedure to reinstall the full stock rom ( if someone could help me I appreciate it ) , but I cannot found the stock ROM CPN-W09 .
Help me please
thank you do much
Daniele ....#