Hi there. I was on stock firmware when the OTA came. I did not installed for a while but when I did my phone went completely dead. I cannot boot into the bootloader nor the recovery. I cannot get fastboot to work. The only hope I have is when I connect it to Windows PC it recognizes it as Qualcomm HS-USB QDLoader 9008 (COM 3). After some research I found that I can do a blankflash, but i cannot find any blankflash files for my phone. So my question is - Is there any way to generate singleimage.bin (for blankflash) or any other way to recover it? Thank you!
Got the same problem. until now no blankflash files available, i guess. Only way is by jtag box. i tried with loader.img for moto x style but it doesnt work for moto x play.
I have the same problem, no blankflash files available until now?
alfafc said:
I have the same problem, no blankflash files available until now?
Click to expand...
Click to collapse
No...
I also have hard brick my phone. I want to get it fixed from this site, is this repair site legit : https://www.aryk.tech/2017/11/moto-x-play-unbrick-solutions.html?m=1
Cooro said:
I also have hard brick my phone. I want to get it fixed from this site, is this repair site legit : https://www.aryk.tech/2017/11/moto-x-play-unbrick-solutions.html?m=1
Click to expand...
Click to collapse
They are frauds.. Many have paid them and got screwed up.. Only way is to do Jtag Flashing or to change the Mother Board (much expensive)
No it is not legit I already got the files from them try my files and tell me if it works for you...also upload it in the global form if working
alwyn naresh said:
No it is not legit I already got the files from them try my files and tell me if it works for you...also upload it in the global form if working
Click to expand...
Click to collapse
It won't work for sure.. The whole project was sponsored by a guy in Hard bricked Moto X Play telegram group created by us.. The only way to fix it is Jtag flashing.. It may cost you around INR 1000.
How to approach jtag?
alwyn naresh said:
How to approach jtag?
Click to expand...
Click to collapse
Below is the address and contact no.. Call him and courier the device.
OMKAR SHINDE
Address
Shop No.2, Shree Datta Apts, Opposite Bramha Garden,
Near Veer Tanaji Ganpati Mandir,
Manikbaug, Pune - 411 051.
Mobile- +919850152245
[email protected]
Thank you so much. It is safe right.they will return the mobile right? Also I got all the unbrick files from ark but none is working any ideas on that? I got qfil files then blank flash files then loader file ...if I send the file to you do you think you can check them for me to see if it works....
alwyn naresh said:
Thank you so much. It is safe right.they will return the mobile right? Also I got all the unbrick files from ark but none is working any ideas on that? I got qfil files then blank flash files then loader file ...if I send the file to you do you think you can check them for me to see if it works....
Click to expand...
Click to collapse
I myself got it fixed from there.. He had fixed more than 200 devices by now.. He even receives devices from abroad.
Thank you very much sir.
alwyn naresh said:
Thank you very much sir.
Click to expand...
Click to collapse
You're welcome buddy.. Just don't waste time on blank flash files.. It just won't work as it isn't digitally signed by Motorola.. Get it fixed from Pune.. That's the only possible solution as of now.. Else you'll have to change the Mother Board..
Hello, after restoring the official firmware and working perfectly the phone, an OTA update appeared, small, I gave it to install as other times ... and from that moment the phone with the black screen.
It seems I'm not the only one, is there any way to revive it?
loparaan said:
Hello, after restoring the official firmware and working perfectly the phone, an OTA update appeared, small, I gave it to install as other times ... and from that moment the phone with the black screen.
It seems I'm not the only one, is there any way to revive it?
Click to expand...
Click to collapse
My daughters has just now done this, no lights, no boot, nothing
Anyway to fix it?
robneymcplum said:
My daughters has just now done this, no lights, no boot, nothing
Anyway to fix it?
Click to expand...
Click to collapse
There is nothing to do ... send it to Motorola and pay the settlement, which is not worth it, they asked me € 195 (according to them, you had to change the motherboard) ... so thrown away.
If it had been to mess with him, but after an official OTA. Never again Motorola.
loparaan said:
There is nothing to do ... send it to Motorola and pay the settlement, which is not worth it, they asked me € 195 (according to them, you had to change the motherboard) ... so thrown away.
If it had been to mess with him, but after an official OTA. Never again Motorola.
Click to expand...
Click to collapse
Jeez... I'm glad it happened when she was using it as a spare phone than me when it was my main phone! Thats a definite NEVER buying a motorola again, even if it was cheap at the time.
My Moto x play completely dead
My moto x play completely not working, I can't able to charge or switch Mobile.
I tried all flashmde or different types of to install., but my mobile was not detected.
But when I connect pc, its showing only Qualcomm name.
Also I tried qflash mode, mobile detecting Qualcomm connected details in my pc but its expecting content or stream file type of firmware stock file.
Can you assist any one where we can get moto x play qflash support file.
Thanks,
Rajesh Kumar R
9962038582
Related
I am just reuploading.
Thanks to toto221 for providing the .enc file and thanks to drkcobra for showing how to convert to sbf.
1FF-p3_kronos_cdma_kronos-user-2.3.5-4.5.1-KNS-29-BST-15-18-release-keys-signed-Boost-US.sbf
http://mir.cr/XT254QDM
http://ul.to/d69svyqu
http://d01.megashares.com/dl/Y0RkwO...29-BST-15-18-release-keys-signed-Boost-US.rar
http://rapidgator.net/file/37089266...T-15-18-release-keys-signed-Boost-US.rar.html
http://bayfiles.com/file/kzu5/dBzB6...29-BST-15-18-release-keys-signed-Boost-US.rar
*WARNING* Even though both models have Sprint logo, the Boost XPRTs are bricked if you flash the Sprint SBF so only flash Boost specific SBF on Boost XPRTs.
I can confirm that this "BOOST XPRT SBF works on Sprint XPRT".
My phone was bricked due to boot-loader error. But this SBF helped me to recover my phone back.
very happy
kapilthio said:
I can confirm that this "BOOST XPRT SBF works on Sprint XPRT".
My phone was bricked due to boot-loader error. But this SBF helped me to recover my phone back.
very happy
Click to expand...
Click to collapse
Are you sure, yours was a Sprint XPRT orignally and its not running Boost SBF? if yes, then thats great news.
All we need now is a root method for GB on XPRT
surfturtle said:
Are you sure, yours was a Sprint XPRT orignally and its not running Boost SBF? if yes, then thats great news.
All we need now is a root method for GB on XPRT
Click to expand...
Click to collapse
I am very sure. I have sprint over the phone (with Sprint Box) and after SBF, it shows Boost in About Phone.
Version - 45.3.15.MB612.Boost.en.US
I do not know what you need to do for CDMA activation on Sprint while you are using Boost ROM. But GSM works just fine
surfturtle said:
I am just reuploading.
Thanks to toto221 for providing the .enc file and thanks to drkcobra for showing how to convert to sbf.
1FF-p3_kronos_cdma_kronos-user-2.3.5-4.5.1-KNS-29-BST-15-18-release-keys-signed-Boost-US.sbf
http://mir.cr/XT254QDM
http://ul.to/d69svyqu
http://d01.megashares.com/dl/Y0RkwO...29-BST-15-18-release-keys-signed-Boost-US.rar
http://rapidgator.net/file/37089266...T-15-18-release-keys-signed-Boost-US.rar.html
http://bayfiles.com/file/kzu5/dBzB6...29-BST-15-18-release-keys-signed-Boost-US.rar
*WARNING* Even though both models have Sprint logo, the Boost XPRTs are bricked if you flash the Sprint SBF so only flash Boost specific SBF on Boost XPRTs.
Click to expand...
Click to collapse
To download the actual file, should i install that livid stuff that these links are throwing?
Also I need to use the XPRT in India. Currently mine is stuck in contacting the server and I am not able to open any menu. Will flashing this help it recover?
Thanks,
Rao
THANKS!!
bytebrahma said:
To download the actual file, should i install that livid stuff that these links are throwing?
Also I need to use the XPRT in India. Currently mine is stuck in contacting the server and I am not able to open any menu. Will flashing this help it recover?
Thanks,
Rao
Click to expand...
Click to collapse
THANKS to all who uploaded this sbf and helped me resurrected my phone! But I am not able to connect to GPRS/3G.. To add an APN (Lebara Australia) I add all details, but after save the APN doesnt show up in the list. Anyone faced this issue?
Thanks,
Rao.
Hello surfturtle,
My girlfriend has a new BOOST XPRT from a Boost Mobile Store that came with GB 2.3.5, but anytime any of her Brazilian GSM SIM cards connect to their network (we've tried TIM and Vivo SIMs) the phone reboots endlessly. The system version already installed on the phone is: 45.3.15.MB612.Boost.en.US
Thinking about reinstalling the one you posted over it, in case the original one on the phone is messed up and causing the GSM issue. What do you think, and how exactly would I do it?
Cheers,
Matt
Sent from my Boost Mobile Motorola XPRT MB612
bytebrahma said:
To download the actual file, should i install that livid stuff that these links are throwing?
Also I need to use the XPRT in India. Currently mine is stuck in contacting the server and I am not able to open any menu. Will flashing this help it recover?
Thanks,
Rao
Click to expand...
Click to collapse
YOU SHOULD NEVER DOWNLOAD LIVID!!!!
Livid is AdWare that many download sites use to generate income from clicks. All those "other" Livid download links are just the same link downloading the "LividInstaller.exe" file.
ALWAYS LOOK FOR THE "REAL" DOWNLOAD LINK, USUALLY ACCOMPANIED BY SOME SORT OF TIMER AND CAPTCHA
JUST TO BE CLEAR:
DO NOT CLICK ON ADS HOSTED LIKE THIS ON DOWNLOAD SITES. IF YOU DO THEN YOU ARE ASKING FOR PROBLEMS WITH YOUR COMPUTER, INCLUDING TOOLBARS, CRAPWARE, ADWARE, SPYWARE, MALWARE, ETC!!!!
YOU HAVE BEEN WARNED!!!
@surfturtle: thanks for this file! It was hard to track down
Awesome, thank you so much! Downloading now (40 more minutes haha) hopefully to cure my phone.
All the links seems to be broken, except rapidgator which too seems to be down. Can someone upload the sbf files please.
harishatrix said:
All the links seems to be broken, except rapidgator which too seems to be down. Can someone upload the sbf files please.
Click to expand...
Click to collapse
you are welcome
1FF-p3_kronos_cdma_kronos-user-2.3.5-4.5.1-110-KNS-46-49-test-keys-signed-Sprint-US.rar
1FF-p3_kronos_cdma_kronos-user-2.3.5-4.5.1-KNS-29-BST-15-18-release-keys-signed-Boost-US.rar
Work in GSM mode
I erased important system files when rooting, no update.zip package worked from recovery mode. The only thing I could do was use "1FF-p3_kronos_cdma_kronos-user-2.3.5-4.5.1-110-KNS-46-49-test-keys-signed-Sprint-US". The phone boots normally, but when put sim card, in gsm mode, restarts over and over, I don't know what else to do, please help me
tekkaman7 said:
I erased important system files when rooting, no update.zip package worked from recovery mode. The only thing I could do was use "1FF-p3_kronos_cdma_kronos-user-2.3.5-4.5.1-110-KNS-46-49-test-keys-signed-Sprint-US". The phone boots normally, but when put sim card, in gsm mode, restarts over and over, I don't know what else to do, please help me
Click to expand...
Click to collapse
Here is the fix
http://forum.xda-developers.com/showpost.php?p=33320200&postcount=676
Better later , than never ...
the link is broken
why i can't extract the sbf that downloaded from link #1 above
and the link #2 is broken
i'm sorry,but i need it to unbrick my xprt
Good Night. There´s anyone who have the .SBF and can upload it again? I bricked my phone and need it urgently. I´ll be very grateful
Could you upload the sbf files again please? I need to recover my phone ´cause i bricked it.
Looks like I have a hard brick with the device manager reporting qhsusb_dload. This appears to be related to corrupt partitioning, the last thing I flashed was a zip package in CWM and rebooted the phone and it didn't reboot by vibrating and showing the Samsung logo, it just was black.
I pulled the battery and attempted to power it on again and I was getting no response from the device, I plugged it into my pc and that's when I saw the qhsusb_dload missing driver which I found drivers for, but it doesn't help me.
My question is, is this something JTAG can fix? I don't want to take a chance on warranty replacement and getting a MF3 factory phone since I wont be able to Loki. Any info would be appreciated.
ChaosMinionX said:
Looks like I have a hard brick with the device manager reporting qhsusb_dload. This appears to be related to corrupt partitioning, the last thing I flashed was a zip package in CWM and rebooted the phone and it didn't reboot by vibrating and showing the Samsung logo, it just was black.
I pulled the battery and attempted to power it on again and I was getting no response from the device, I plugged it into my pc and that's when I saw the qhsusb_dload missing driver which I found drivers for, but it doesn't help me.
My question is, is this something JTAG can fix? I don't want to take a chance on warranty replacement and getting a MF3 factory phone since I wont be able to Loki. Any info would be appreciated.
Click to expand...
Click to collapse
Yes, unfortunately it's down to JTAG with a RIFF box or similar equipment.
GiantBallSack said:
Yes, unfortunately it's down to JTAG with a RIFF box or similar equipment.
Click to expand...
Click to collapse
Figures... now I gotta find someone that can do the JTAG/RIFF repair.
ChaosMinionX said:
Figures... now I gotta find someone that can do the JTAG/RIFF repair.
Click to expand...
Click to collapse
I found this on GSM-Hosting, and was reported to be a Samsung driver. If the driver installs successfully, QPST will probably see the phone, but I doubt that ODIN would. I still think you are down to JTAG, but here's the driver if you want to mess around with the phone some more
GiantBallSack said:
I found this on GSM-Hosting, and was reported to be a Samsung driver. If the driver installs successfully, QPST will probably see the phone, but I doubt that ODIN would. I still think you are down to JTAG, but here's the driver if you want to mess around with the phone some more
Click to expand...
Click to collapse
Thanks, I had the drivers after looking on google so now it shows up as Qualcomm HS-USB QDLoader 9008 (COM6). ODIN so far doesnt appear to be able to see the phone any longer. Will QPST be able to do anything?
ChaosMinionX said:
Thanks, I had the drivers after looking on google so now it shows up as Qualcomm HS-USB QDLoader 9008 (COM6). ODIN so far doesnt appear to be able to see the phone any longer. Will QPST be able to do anything?
Click to expand...
Click to collapse
If you had a full flash file, you could flash it with QPST and unbrick it. Those files are extremely hard to come by, only the service centers seem to have them. It may be possible to backup a different S4 and flash it but you may end up with an identical copy of the other person's phone. My only experience with QPST is changing the service programming for CDMA phones. Hard-bricks I had equipment for. I have it installed, I'll see if I can pull a dump of my phone that can be flashed, but I still wonder about the EFS partitions.
GiantBallSack said:
If you had a full flash file, you could flash it with QPST and unbrick it. Those files are extremely hard to come by, only the service centers seem to have them. It may be possible to backup a different S4 and flash it but you may end up with an identical copy of the other person's phone. My only experience with QPST is changing the service programming for CDMA phones. Hard-bricks I had equipment for. I have it installed, I'll see if I can pull a dump of my phone that can be flashed, but I still wonder about the EFS partitions.
Click to expand...
Click to collapse
Alright thanks, yeah I can get the phone in QPST its listed in Download mode. Wonder if a dump from a working phone could fix it?
ChaosMinionX said:
Alright thanks, yeah I can get the phone in QPST its listed in Download mode. Wonder if a dump from a working phone could fix it?
Click to expand...
Click to collapse
It's possible. Check your PM.
JTAG service only. Period
Sent from my GT-I9505 using xda premium
TheAxman said:
JTAG service only. Period
Sent from my GT-I9505 using xda premium
Click to expand...
Click to collapse
Anyone on the forum do JTAG service? I dont want to take chance of ATT warranty sending me a MF3 phone.
GiantBallSack said:
It's possible. Check your PM.
Click to expand...
Click to collapse
I've done a lot of research and experimenting in this area, because I'm currently stuck in a similar situation with my phone stuck in QPST mode. If you have any knowledge about a working .hex file for this device, please let me know (PM me if needed?).
TheAxman said:
JTAG service only. Period
Sent from my GT-I9505 using xda premium
Click to expand...
Click to collapse
Pretty much. Unfortunately in my case, JTAG appears not even a viable option. Might be different for the OP, however. Probably has a different "style" of hard-brick.
ChaosMinionX said:
Anyone on the forum do JTAG service? I dont want to take chance of ATT warranty sending me a MF3 phone.
Click to expand...
Click to collapse
There's a few people on the forums with JTAG boxes offering service. Perhaps the most reputable would be @connexion2005 - his website is mobiletechvideos.com. Costs $60 for an S4, plus extras (rush shipping, rush processing, data recovery, etc.), last I looked.
Only problem is, if you're hard-bricked because of the MF3 update somehow, you might be SOL. Last I heard, mobiletechvideos.com sent back a phone to another XDA member, unfixed for this reason. Still waiting to hear the whole story on this, so I wouldn't discredit mobiletechvideos.com yet. They're very good at what they do, and they've repaired thousands of hard-bricks on many different models of phones.
Aou said:
I've done a lot of research and experimenting in this area, because I'm currently stuck in a similar situation with my phone stuck in QPST mode. If you have any knowledge about a working .hex file for this device, please let me know (PM me if needed?).
Click to expand...
Click to collapse
We worked on a good bit today, and QPST just wouldn't cooperate with the phone in anyway. It wouldn't write aboot.mbn like the phone needs. A full flash in .mbn format is needed.
GiantBallSack said:
We worked on a good bit today, and QPST just wouldn't cooperate with the phone in anyway. It wouldn't write aboot.mbn like the phone needs. A full flash in .mbn format is needed.
Click to expand...
Click to collapse
Correct. Also need an appropriate .hex file too for certain operations in QPST.
I've tried flashing certain .mbn files that are explicitly designed to convert the entire device into a glorified 16gb, unformatted flash drive (which is repairable using very careful DD commands from a linux PC), but I can't get the device that far. Problem is, the only .hex and .mbn files out there for the MSM8960 are not signed, and the device refuses to accept them.
Aou said:
Correct. Also need an appropriate .hex file too for certain operations in QPST.
I've tried flashing certain .mbn files that are explicitly designed to convert the entire device into a glorified 16gb, unformatted flash drive (which is repairable using very careful DD commands from a linux PC), but I can't get the device that far. Problem is, the only .hex and .mbn files out there for the MSM8960 are not signed, and the device refuses to accept them.
Click to expand...
Click to collapse
I didnt have MF3 official on there, the only files from MF3 I used were the Modem, and Tasks's latest AOKP had MF3 RIL. I wonder if I am in the same boat as you?
I do however have a replacement device on its way tomorrow, I wonder if ATT has officially gone to MF3 for replacement warranty devices yet?
ChaosMinionX said:
I didnt have MF3 official on there, the only files from MF3 I used were the Modem, and Tasks's latest AOKP had MF3 RIL. I wonder if I am in the same boat as you?
I do however have a replacement device on its way tomorrow, I wonder if ATT has officially gone to MF3 for replacement warranty devices yet?
Click to expand...
Click to collapse
I certainly hope they haven't. If they have, I'd rather pay the $199 deductible on a new device through insurance instead!
Aou said:
I certainly hope they haven't. If they have, I'd rather pay the $199 deductible on a new device through insurance instead!
Click to expand...
Click to collapse
You and me both! I would just assume sell the warrantied device and pay difference to get a Google Edition, I am not real keen on HTC phones. Guess we will see what they ship me when it arrives tomorrow!
Aou said:
Correct. Also need an appropriate .hex file too for certain operations in QPST.
I've tried flashing certain .mbn files that are explicitly designed to convert the entire device into a glorified 16gb, unformatted flash drive (which is repairable using very careful DD commands from a linux PC), but I can't get the device that far. Problem is, the only .hex and .mbn files out there for the MSM8960 are not signed, and the device refuses to accept them.
Click to expand...
Click to collapse
nevermind, sorry
Well good news! My replacement from warranty came today and its still running MDL, so guess I will be returning the bricked device. Sigh of relief seeing MDL and not MF3 thats for sure :good::good:
ChaosMinionX said:
Well good news! My replacement from warranty came today and its still running MDL, so guess I will be returning the bricked device. Sigh of relief seeing MDL and not MF3 thats for sure :good::good:
Click to expand...
Click to collapse
man you sure lucked out there
GiantBallSack said:
It's possible. Check your PM.
Click to expand...
Click to collapse
Hey, could you tell me how it is possible ?
i have a I9505 in QPST DL mode and i don't know how to get a dump from a working model !
thx !
DELETED
4llerbuntu said:
Hello.
PLEASE HELP ME.
I totally bricked my device. completely dead. i wiped the wrong partitions in fastboot, now it won't get detected at all. it won't even come on.
I'm in a country where its not possible to send it in to Asus for repairs.
computer still sees it as Qualcomm HS-USB QDLoader 9008
but i don't have the necessary tools or files to recover it. PLEASE HELP ME>.
Click to expand...
Click to collapse
Start saving money for new phone :^)
BTW just out of curiosity, what did you wipe?
DELETED
does your phone boot
4llerbuntu said:
The firmware partitions, modem, hyp, sbl1, recovery.
Forgot to flash them back before reboot.
Ive since learnt one can recover with QPST and some files. Problem is i cant find them for Asus.
Click to expand...
Click to collapse
you didn't wipe aboot, abootbak, hypbak? right? Our phone has a backup partition for each partition (abootbak, hypback, sbl1bak, modembak, etc), asus included these, so there must be some way to use them to unbrick. Are you able to reboot to fastboot mode? ( i guess not, but still to confirm)
You can unbrick with QFIL ONLY if you manage to find your device's RAM IMAGE (usually MPRxxxx.mbn) and BOOT IMAGE (usually xxxx_msimage.mbn). Other flash files are included in asus fota, only these two are not. @shakalaca might help to find these files or the entire service ROM. I have been searching for asus service but to no avail . I have flashed many lenevo and xiomi phones with QFIL. Here's is a very nice guide http://www.androidbrick.com/unbrick...-you-have-the-right-kind-of-rom-qhsusb_dload/
You can request for ZF2 laser's service ROM on that website/blog. GSM FORUM is also a good forum to request service ROMs
DELETED
mohamedelkholy said:
does your phone boot
Click to expand...
Click to collapse
No it doesn't boot. It won't even power on
But it still gets detected as Qualcomm device when plugged in to pc
4llerbuntu said:
No i didnt wipe those.
Will the MPRxxx.mbn and msimage.mbn for another phone but similar processor and chipset work? I found those for MSM8916 for another device and im hoping i can use those.
Click to expand...
Click to collapse
I never cross flashed ram image. Be patient. Don't flash other device's ram image, it may worsen conditions. Keep this as the final solution, but NOT NOW. Also, you need boot image (.mbn) too.
DELETED
DELETED
deleted
Deleted
deleted
Deleted
Deleted
4llerbuntu said:
hmmn, i'm so sad. so nobody is willing to help me at all?
Click to expand...
Click to collapse
not really, I think we're all (ok, just me) don't have that knowledge to help you, or simply can't
4llerbuntu said:
i always assumed all the people who post on this board had the device.
Click to expand...
Click to collapse
Yes, all people there should have laser, and no, i dont have your type, and someone maybe just lurking around, want to buy this laser phone if they feel like it
4llerbuntu said:
Surely i can't be the only person who will ever have this problem.
Click to expand...
Click to collapse
Yes, me too, I think someone will do this thing, don't know why, just feel like it?
4llerbuntu said:
i hope someone is willing to help when it happens to another person.
Click to expand...
Click to collapse
I'm hope we got that knowledge too
4llerbuntu said:
Maybe i should just give up. i'm so down right now.
alright bye.
Click to expand...
Click to collapse
Sorry to hear that
Sent from my ASUS_Z00RD using XDA Labs
4llerbuntu said:
computer still sees it as Qualcomm HS-USB QDLoader 9008
but i don't have the necessary tools or files to recover it. PLEASE HELP ME>.
Click to expand...
Click to collapse
Are you sure msimage is same as gpt? I have attached my ze550kl msm8916 gpt dump. Seems there are three- gpt, gpt1, and gpt2. Try your luck with each one by one.
And please stick to one thread, b7mping the forum is not a solution to your problem. Update your OP by mentioned.ing the workarounds you have tried till now and useful links you have visited for fixing the issue. I know a friend who is a mobile repairer. He might have the service rom for your device. I am waiting for his reply
sziraqui said:
Are you sure msimage is same as gpt? I have attached my ze550kl msm8916 gpt dump. Seems there are three- gpt, gpt1, and gpt2. Try your luck with each one by one.
And please stick to one thread, b7mping the forum is not a solution to your problem. Update your OP by mentioned.ing the workarounds you have tried till now and useful links you have visited for fixing the issue. I know a friend who is a mobile repairer. He might have the service rom for your device. I am waiting for his reply
Click to expand...
Click to collapse
Thank you. I will do that
4llerbuntu said:
Hello.
PLEASE HELP ME.
I totally bricked my device. completely dead. i wiped the wrong partitions in fastboot, now it won't get detected at all. it won't even come on.
I'm in a country where its not possible to send it in to Asus for repairs.
computer still sees it as Qualcomm HS-USB QDLoader 9008
but i don't have the necessary tools or files to recover it. PLEASE HELP ME>.
Click to expand...
Click to collapse
Read this and see if any if it applies.
www.androidbrick.com/unbrick-recover-your-dead-lg-g3-g2-all-variants
I'm not sure how the tool works, but maybe you can pull your backups and write back your partitions from the backup.
Sent from my ASUS_Z00TD using Tapatalk
Mods please help close this thread. ........
Need Help!,
Updated my xt1643 indian g4 plus to the June Security Patch (NPJS25.93.14-8) build.
Post that I unlocked the bootloader and installed AOSPX rom after which I wanted to go stock nougat.
I flashed the marshmallow rom and took the ota to nougat and now my screen is all black, not even being able to boot the device to fastboot.
By exploring the forums I got to know that I've hard bricked my device but this thing never happened before the june update.
I'm not even able to use the blank files method to revive my device:crying::crying:
Please help
Only choice
https://forum.xda-developers.com/moto-g4-plus/help/solved-unbrick-hard-bricked-dead-t3585016
drmuruga said:
Only choice
https://forum.xda-developers.com/moto-g4-plus/help/solved-unbrick-hard-bricked-dead-t3585016
Click to expand...
Click to collapse
thank you, but it did not work. Also I read around the forum that I would be needing the latest blank flash files which would be capable enough to be flashed on the June Security Rom(NPJS.25.93.14-8)
gautamchawla195 said:
thank you, but it did not work. Also I read around the forum that I would be needing the latest blank flash files which would be capable enough to be flashed on the June Security Rom(NPJS.25.93.14-8)
Click to expand...
Click to collapse
You must Press Power Button and Volume down for 2-3 Minutes and Hold them. ( Handy must be connected to the charger !!! )
This means more then 120 Seconds.Then your handy will boot to Recovery.
then navigate to "start" in recovery with volume buttons and hit "power button" that it starts normally.
Try this please it helped me....and say us if it worked for you !
this solutions helps if android gets freezed .I first tough also my handy was death.But it worked for me.
But remember it must be connected to charger and press more then 120 seconds and hold !!!This will work on all Motorola Handys with Android.
majo3000 said:
You must Press Power Button and Volume down for 2-3 Minutes and Hold them. ( Handy must be connected to the charger !!! )
This means more then 120 Seconds.Then your handy will boot to Recovery.
then navigate to "start" in recovery with volume buttons and hit "power button" that it starts normally.
Try this please it helped me....and say us if it worked for you !
this solutions helps if android gets freezed .I first tough also my handy was death.But it worked for me.
But remember it must be connected to charger and press more then 120 seconds and hold !!!This will work on all Motorola Handys with Android.
Click to expand...
Click to collapse
This is something new apart of which I've been researching around forums.
Btw, would work as per the given fix and keep you posted
gautamchawla195 said:
This is something new apart of which I've been researching around forums.
Btw, would work as per the given fix and keep you posted
Click to expand...
Click to collapse
Nupp, not working, I too think that I should wait for the full june security rom and post that the blank flash files to get my device alive again. I would please request someone to gain access to the blank flash files after the june rom is released.
June security update won't let you downgrade and has bricked many devices. You have to wait until full rom of 6/17 is released as you've said. If under warranty, you can send it in. If insured, you can try to kill your phone by dropping in water and collect insurance.
HueyT said:
June security update won't let you downgrade and has bricked many devices. You have to wait until full rom of 6/17 is released as you've said. If under warranty, you can send it in. If insured, you can try to kill your phone by dropping in water and collect insurance.
Click to expand...
Click to collapse
Yes, we would be needing the updated blank flash files for the june update, can you please tell me about how long the june blank flash files are released after the full fastboot rom is released as per the past experiences and would that increase chances for my device to get revived?
June full ROM lauched:
https://rsdsecure-cloud.motorola.co...ubsidy-DEFAULT_regulatory-DEFAULT_CFC.xml.zip
How can I extract the blankflash from this ROM? It's possible? Please, help me! I didn't found in Google a way to get these files to save my moto g4+ hard briked
pekenolucas said:
June full ROM lauched:
https://rsdsecure-cloud.motorola.co...ubsidy-DEFAULT_regulatory-DEFAULT_CFC.xml.zip
How can I extract the blankflash from this ROM? It's possible? Please, help me! I didn't found in Google a way to get these files to save my moto g4+ hard briked
Click to expand...
Click to collapse
Well, we're gonna need a copy first to see what's inside - that link keeps giving me access denied. Presumably it's only for service centres or for developers. Strange, it's working now...
This link is OK! I downloaded it right now using Chrome from my phone. I'm from Brazil.
pekenolucas said:
This link is OK! I downloaded it right now using Chrome from my phone. I'm from Brazil.
Click to expand...
Click to collapse
Ah, you're right - dunno why the link gave me access denied initially - it's downloading okay too now.
EDIT - just downloaded the ROM and had a look - no sign of a new blank flash that could help us unfortunately.
Looks like the only resolution, unfortunately, for a bricked device involving the NPJS25.93-14-8 update, (whether it was downgraded with a stock ROM, or you somehow downgraded from the June update, and then updated with the June OTA) is to send it for service or save up for a new device.
echo92 said:
Ah, you're right - dunno why the link gave me access denied initially - it's downloading okay too now.
Click to expand...
Click to collapse
echo92, can you plzz check and also ask vache and some of the other developers too, to go through the june rom and see if there's any file which we can use to revive our devices.
Edit: sorry, didn't saw ur reply
Gpt.bin from ROM have same archives from blankflash, but gpt.bin have 32kb and blankflash more than 3Mb! Anyone know how to put gpt.bin data inside blankflash to update the partition table and possible unbrick the device? It's just an idea!
pekenolucas said:
Gpt.bin from ROM have same archives from blankflash, but gpt.bin have 32kb and blankflash more than 3Mb! Anyone know how to put gpt.bin data inside blankflash to update the partition table and possible unbrick the device? It's just an idea!
Click to expand...
Click to collapse
is there anyway to edit contains of singleimage.bin ?
The blankflash stays the same.. only the gpt.bin and bootloader.img are to be changed accordingly
echo92 said:
Well, we're gonna need a copy first to see what's inside - that link keeps giving me access denied. Presumably it's only for service centres or for developers. Strange, it's working now...
Click to expand...
Click to collapse
Can you upload a copy if you've downloaded it? The link doesn't work now. Seems to have been removed.
gpt.bin of the latest firmware and singleimage.bin file from the Blankflash seems to be having the same contents.
I tried renaming gpt as singleimage and tried using blankflash
It didn't work. Also the size of both the files are not even comparable one is 32kb and another is 4mb
tywinlannister7 said:
The blankflash stays the same.. only the gpt.bin and bootloader.img are to be changed accordingly
Click to expand...
Click to collapse
Yes, but I think that Bootloader.img and GPT.bin are inside singleimage.bin data, because it rewrite these information on bricked phones. I don't know singleimage.bin have signed data. If it had signed data, no chance to patch/modify it!
I'll try some hex editor and run some tests!!!
zeomal said:
Can you upload a copy if you've downloaded it? The link doesn't work now. Seems to have been removed.
Click to expand...
Click to collapse
tywinlannister7's kindly uploaded the ROM for us [EDIT - link removed as the ROM appears to cause loss of SIM for some devices]
Hello it is a pleasure to greet.
I have a serious problem, I was installing the latest update of your rom and my phone did not have enough charge.
It is dead, does not turn on, does not enter recovery mode or download.
My computer only recognizes it USB QDLOAD 90008.
chinitopex said:
Hello it is a pleasure to greet.
I have a serious problem, I was installing the latest update of your rom and my phone did not have enough charge.
It is dead, does not turn on, does not enter recovery mode or download.
My computer only recognizes it USB QDLOAD 90008.
Click to expand...
Click to collapse
Did you charge it?! Lol
I mean that if your battery works properly
amirizad_7436 said:
Did you charge it?! Lol
I mean that if your battery works properly
Click to expand...
Click to collapse
Yeah, Work perfectly the battery in other phone.
chinitopex said:
Yeah, Work perfectly the battery in other phone.
Click to expand...
Click to collapse
Here is an unbrick.img that I made a while back and can be flashed to an external drive.
https://mega.nz/#!ceYi3CSA!sNYh4FSaL6viErBzbXCKKm_GMRHiZJfU4IpF7ajrVQk
Follow the instructions here and it should be okay (fingers crossed) DO NOT FLASH THE FILE GIVEN IN THAT THREAD. That file is for j500h and will probably cause problems. Use the file I provided
https://forum.xda-developers.com/galaxy-j5/how-to/how-to-unbrick-galaxy-j5-sm-j500h-t3536287
garylawwd said:
Here is an unbrick.img that I made a while back and can be flashed to an external drive.
https://mega.nz/#!ceYi3CSA!sNYh4FSaL6viErBzbXCKKm_GMRHiZJfU4IpF7ajrVQk
Follow the instructions here and it should be okay (fingers crossed) DO NOT FLASH THE FILE GIVEN IN THAT THREAD. That file is for j500h and will probably cause problems. Use the file I provided
https://forum.xda-developers.com/galaxy-j5/how-to/how-to-unbrick-galaxy-j5-sm-j500h-t3536287
Click to expand...
Click to collapse
Thanks a lot.
I'll try to do it in a moment, will be giving details very soon.
@ garylawwd
Your files work perfectly in other Samsung J500M, but I have a problem, it didn't work on my phone
it seems that something is damaged on the board.
chinitopex said:
@ garylawwd
Your files work perfectly in other Samsung J500M, but I have a problem, it didn't work on my phone
it seems that something is damaged on the board.
Click to expand...
Click to collapse
Aww that sucks. I'm not sure what else there is you can try.
Looks like it's time to upgrade or you can replace the logic board for like 50 euro/dollars/pounds whatever your currency is but it doesn't seem worth it for a 5 year old budget device
garylawwd said:
Aww that sucks. I'm not sure what else there is you can try.
Looks like it's time to upgrade or you can replace the logic board for like 50 euro/dollars/pounds whatever your currency is but it doesn't seem worth it for a 5 year old budget device
Click to expand...
Click to collapse
Thanks for the support.
I remember that my cell phone only turned off then did not turn on again
it's true, I think I should buy another one. I can tell you, that the files to put it in download mode works very well,
I check it with another J500M and on 4gb not required 16GB.
Edit...
Hi Againg
Last night I tried to revive from my laptop and today I tried again from my PC and it worked.
Can use 4GB Sd Card not necessary 16GB
My phone is alive again
Attach the photos the files