Related
First of all, i have read some similar threads about this, and all advise diffrent solution besides the hardware mod, I have tried for 2 days all methods in Miui forums and none have worked for me except the hardware method.
My Device: Xiaomi Redmi Note 3 Pro / SD version.
State:
-would only show "Mi" logo when powered on.
-Would enter only Fastboot.
- No EDL mode
- No recovery
-bootloader locked
-In this state, you can't flash absolutely nothing with any software. (from fastboot).
Requirements:
- windows 7/ windows 10 x64 edition.
- ONLY LATEST version of miflash, from 2016 onward, so it has the required drivers and methods to work with the phone. (I have tried with older versions and it did not work, i thought there was no hope for my phone).
- one hard bricked Redmi Note 3 Pro
- any fersion of Stable FASTBOOT OFFICIAL rom. (.tgz extension) - I personally used kenzo_global_images_V7.2.3.0.LHOMIDA_20160129.0000.14_5.1_global_c85ba6c524.tgz
- medium disassembly skills,
- a lot of patience,
- minimum set of tools (one small cross screwdriver, 1-2 strong finger nails, good eyesight).
- one microusb cable
HOW TO:
1. uninstall all drivers and software related to the Xiaomi phone. (I ended up reinstalling windows 7 just to be sure all was gone - that is how desperate I became). To be sure this is done correctly, with the phone turned off, connect it to the computer.
Go into device manager, search in com ports, or wherever any drivers are installed for the phone, and uninstall all of them, ticking remove driver files also.
after doing this, hit refresh, and see if any drivers get installed again.
Repeat until there are no drivers installed, and the device will be without a driver.
2. Disconnect the phone and RESTART WINDOWS
3. Disable driver signature verification/enforcement:
a. in windows 7, this is easy: restart windows, hit f8 until a menu pops up where you can choose disable driver signature verification/enforcement.
b. in windows 10, it is a little bit longer, but: http://www.howtogeek.com/167723/how...8.1-so-that-you-can-install-unsigned-drivers/ - Be careful, when choosing the option in the last menu, use F... keys, not number keys.
4. while in windows, in the bottom right corner, there should be a message saying "test mode"
5. install ONLY the LATEST VERSION of Miflash! you may get some messages about driver installation (2 times), allow installation!
6. RESTART WINDOWS
7. Prepare the phone!: I followed the video here, even I did not understand the language: http://choimobile.vn/threads/video-...o-snapdragon-650-fix-download-mode-edl.65098/
- First, I used my nail to open the phone up, just like in the video. It is great that the screen is not glued to the body, there are only some clips holding it in place!
- after opening the cover please be careful - there is a cable connecting the case to the mainboard - the fingerprint sensor.
- after this, unscrew the 7 or 8 screws as in the video.
- unlock the cables as in the video - please be sure not to disconnect all the cables.
- now, first get the antenna plastic cover outside of the way.
- after disconnecting the camera module, I would personally advise you to get the camera out of the way first, as there is a piece of foil glued between the mainboard and the underneath of the camera module (on the display)
- with great care, rise the Mainboard from the display.
- to have better access to the testpoint pins, I turned the Mainboard over the battery.
- now, connect the microusb cable to the phone.
8. connect the phone to the computer.
9. go into device manager and check if there are any devices installed, there should be under ports.... a device called Qualcomm HS-USB Diagnostics 900E.
10. Now comes the tricky part, switching the phone to EDL mode (emercency download)
look on the back of the motherboard of the phone to connect the 2 testpoint pins as in the video. You can use anything to do this. a metal wire, a small scissors, an untied paperclip... You will have to do this while device manager is opened, as you must check it when the driver changes to "qualcomm hs-usb qdloader 9008".
Please be careful when trying to connect the 2 pins not to touch any metal housing, ans this will restart the device each time.
Now, try and try and try until the driver changes to "qualcomm hs-usb qdloader 9008".
11. unzip the rom using 7 zip to a destination of your choosing. I advise as short destination as possible and no spaces used in the folder naming. I unpacked it in C:\rom\
12. Open Miflash
13. As per other many many instructions:
a. click browse - select the folder where you unpacked the rom (for me, c:\rom\)
b. click the arrow next to brows button and select advanced.
c. in the first field, navigate to the folder where the rom was unpacked and select flashall.bat
d. in the third field select prog_emmc_firehose_8976_ddr.mbn from the "images"folder in the folder whre he rom was extracted
e. field 7: rawprogram0.xml and field8: patch0.xml
f. Hit the Refresh button, the device should appear as a com port in the white field of Miflash.
g. just to be sure, tick also "flash all" in the bottom of miflash.
14. Hit the Flash button on Miflash and this should be the last step before powering up your revived Xiaomi Redmi Note 3.
This is what I learned in the past 2-3 days.
Different errors I got during the learning process and what i did to avoid them:
- different problems with drivers not installing correctly or showing different device names - just use the method i pointed out in the beginning to uninstall any driver previously installed on the computer, with the refresh in device manager and than uninstalling all.
- "end of package" error at second 2 while flashing in Miflash - you are using an older or an unsupported version of miflash, just use the latest one.
- not being able to flash anything while in fastboot - if you have a locked bootloader, on redmi note 3 snapdragon version, you simply won't be able to flash anything. end of story. this is the whole purpose of having a locked bootloader.
- trying to go into EDL mode using fastboot comand "fastboot oem eld" - this will not work for a really bricked device as was mine. the only solution is to go through the tespoint pin connection.
i wonder if there's a way not to make trwp locked in the recovery partition, so if someone flashes a factory rom without precaution, twrp will simply get overwritten by factory recovery. Wouldn't that prevent these hard bricks?
btw, nice guide
Please move the thread into guides/tutorial section.
Well, mine was bricked too 2 days ago... even I already unlock the bootloader using the official way.
It happened because I'm on AOSP and I flash Xiaomi.EU ROM from TWRP.
'MI' Logo flashed twice then the phone turns off itself.
It can't boot, can't enter EDL mode. I just can go into fastboot mode. But nothing can be done there because it always says 'device is locked'.
'fastboot oem device-info' also says the phone is on locked state.
Dunno why this happen, I think its because I play with the unlock bootloader toggle on previous MIUI and AOSP ROM.
After countless of times trying to get into EDL, I give up.
Device manager always show "QCom HS-USB Diagnostic 900E" instead of "QCom HS-USB QLoader 9008"
Finally I try the official Mi Unlock software, re-unlock success and BAM... Phone boots again into system. lol...
This makes me think the bricked problem can prevented/solved to by:
- At least bind a Xiaomi Account to your phone once when using official ROM (recommended China Dev ROM)
- Use that account to apply for the unlock, and when you got the phone bricked/relocked, you can re-unlock it using official way to revive the phone
Now is possible unbrick without disassembly:
http://en.miui.com/thread-267263-1-1.html
http://www.htcmania.com/showthread.php?t=1174700
jujusito said:
Now is possible unbrick without disassembly:
http://en.miui.com/thread-267263-1-1.html
http://www.htcmania.com/showthread.php?t=1174700
Click to expand...
Click to collapse
please read through all the thread, don't just throw in a link. the method mentioned by you will not work on some bricked devices, including mine. this did not work for me, so I ended up disassembling the phone.
aabenroi said:
Well, mine was bricked too 2 days ago... even I already unlock the bootloader using the official way.
It happened because I'm on AOSP and I flash Xiaomi.EU ROM from TWRP.
'MI' Logo flashed twice then the phone turns off itself.
It can't boot, can't enter EDL mode. I just can go into fastboot mode. But nothing can be done there because it always says 'device is locked'.
'fastboot oem device-info' also says the phone is on locked state.
Dunno why this happen, I think its because I play with the unlock bootloader toggle on previous MIUI and AOSP ROM.
After countless of times trying to get into EDL, I give up.
Device manager always show "QCom HS-USB Diagnostic 900E" instead of "QCom HS-USB QLoader 9008"
Finally I try the official Mi Unlock software, re-unlock success and BAM... Phone boots again into system. lol...
This makes me think the bricked problem can prevented/solved to by:
- At least bind a Xiaomi Account to your phone once when using official ROM (recommended China Dev ROM)
- Use that account to apply for the unlock, and when you got the phone bricked/relocked, you can re-unlock it using official way to revive the phone
Click to expand...
Click to collapse
I also applied for an unlock code, but this takes up to 15 days, and I have the phone for only 3 days . I could not wait for the code, I had to do something to revive it.
meangreenie said:
i wonder if there's a way not to make trwp locked in the recovery partition, so if someone flashes a factory rom without precaution, twrp will simply get overwritten by factory recovery. Wouldn't that prevent these hard bricks?
btw, nice guide
Click to expand...
Click to collapse
I made a modified TWRP which will not cause hard bricks
Rajdip said:
I made a modified TWRP which will not cause hard bricks
Click to expand...
Click to collapse
great work! your modded twrp will no doubt save me when i forget i have to delete the emmc file in the future.
Dear, thank you for your contribution, this deserves to be a section more important, really saved my phone from the hard brick. Again very grateful
how do i know what a test point looks like on any phone? like the new redmi 3s? i cant get into edl because im stuck in Qualcomm HS-USB Diagnostics 900E
xdarkmario said:
how do i know what a test point looks like on any phone? like the new redmi 3s? i cant get into edl because im stuck in Qualcomm HS-USB Diagnostics 900E
Click to expand...
Click to collapse
maybe look for something like this?
http://choimobile.vn/Temp/Testpoint_Redmi_Note3_PRO_3.jpg
I doubt they will have much variance from xiaomi phone to phone to make it easy for factory / repair centers to fix many models... (I could be wrong though), other brands are probably different.
Well you can enter edl mode from fastboot via this simple tool
http://forum.xda-developers.com/and.../guide-how-to-reboot-to-edl-fastboot-t3394292
And then you can flash any miui .tgz based rom and resurrect.
I hard bricked my Device last night and resurrected
PS : you must have the MiPcSuit installed
ilvmyname said:
Well you can enter edl mode from fastboot via this simple tool
http://forum.xda-developers.com/and.../guide-how-to-reboot-to-edl-fastboot-t3394292
And then you can flash any miui .tgz based rom and resurrect.
I hard bricked my Device last night and resurrected
PS : you must have the MiPcSuit installed
Click to expand...
Click to collapse
links dead
Quick addition: if you're using Virtual Box, like me (on a mac), you need to enable USB 2.0 on the virtual machine. On Virtual Box, this means you have to add an extension pack. This might save you 48hrs, like it cost me
I have meizu m2 note. Its now bricked. I was using sp flash tool to unlock the bootloader and install twrp recovery.
i was following the guide giving on youtube. I can't attach an outside link here.
So i did everything this guide said, but on the last step when i switched off my phone and connected to the usb port. The sp flash tool stopped working i waited for 5-10 mins. Finally it crashed. Now when i try to connect my phone it says usb device not recognised (the last device you connected to this computer malfunctioned). I cannot start my phone. I tried pressing the power button for 10 secs, tried pressing volume + with power button, nothing happens.
Anybody have any idea how to solve this.
Go to download old version Flyme os 4+ any but original rom you have must install,
And dow load any latest sp tool,
And also downlaod latest all mtk devices drivers,
If you have system knoledge you can install all of these pc softwares,
Test it once again your phone connecting to computer,
Just detected only nothing. Can do that its just detected your will be alive soon but its very easy if you know a little bit mobile knowledge,
Lets go to process
Step 1 check best and good branded usb connecting cable, test to connect usb cable to your phone,
Step 2 extract Flyme stock rom, and extract mtk sp tool,
Step 3 open sp tool showing error there is no any scatter. Or download file dont worry, da file availble at sptools folder you can go and select, and scatter. File availble at flyme stock rom folder lets check it then select firmware all formate and install that you have to select that option, then you select download and now connect your phone just leave ituntill done then your phone is will alive feel happy like me if you need any more information any other problem connect. To. Me
Can you speak more clearly?I don't understand.Because my English is not very good.
zzx3731 said:
Can you speak more clearly?I don't understand.Because my English is not very good.
Click to expand...
Click to collapse
What problem with your phone?
Hi ! I have the same problem right now, when I plug it, it says device not recognised, what could I do now ?
Thank you very much，This is my mobile phone. It's done.Thank you for your kindness.
：○
Hagadou said:
What problem with your phone?
Click to expand...
Click to collapse
I been able to install LineageOS, I fixed it by pressing home and menu button, it disconnect and reconnect and i been able to Re-flash it with the recovery and when i tried to install Lineage, my error was gone (error 7)
Ok guys here is the step by step even for noobs how to unbrick Xiaomi Mi Max (helium).
If you have access to fastboot jump to step 11
Requirements :
* MiFlash Beta :Download Here
* MiFlash 20151028 : Download Here
* Global Fastboot Rom : Download Here
* Xiaomi Qualcomm Drivers
* Screw and tools.
* Paper clip or cable
* For sure Usb Cable.
Now if you all ready lets continue repair. First of all you need to open back cover.
1) Open Back cover and disconnect fingerprint sensor and battery. Dont connect battery till you finish whole process. (How to disassemble video : https://www.youtube.com/watch?v=YMG04GqVU_0&t=64s)
2) Make a paper clip to setup short circuit in your mainboard. Here are the testpoints. https://s15.postimg.org/s0j0qhq3v/Xiaomi_Max_Test_Points.png
3) Ok here is the hardest and trickiest one. While you are holding paper clip or cable with those testpoint you need to connect phone to pc. My suggestion 1st connect usb cable to phone then make short circuit then connect to pc.
* One more time you need to connect phone to pc while those two testpoints connected to eachother with a paperclip or a cable.
4) Here is the second tricky part. Unzip rom file. Important part is the name of folder. Please try to make it as short as possible.
Ex : C:\mimax\
So after extraction your folder will looks like this : http://oi63.tinypic.com/334rr11.jpg
5) You need to install both MiFlash versions. They are 2 different software so you shouldnt see any errors like "it is already installed".
6) Go To C:\XiaoMi\XiaoMiFlash and run XiaoMiFlash.exe as an administrator. Click browse and choose your rom folder. NOT IMAGES FOLDER ROM FOLDER !!!! ( Ex : C:\mimax)
7) Click "refresh" you will see COM port and click "flash" If you dont see any COM port here first check if you installed drivers correctly. If drivers are installed correct please go back to step 3 and try again.
8) Install will start and continue and %99 possibly it will stop in the middle You will receive Max buffer 256 error. No worries just keep calm and take deep breath. Go to next step
9) Disconnect usb cable from pc and phone. Reconnect battery. Now voila phone will ready to work BUT NOT READY TO WORK FLAWLESS. So now put your phone to fastboot mode. Yes you read correct now your phone will be in fastboot mode even it could be ready to use but just wait for next step.
10) Fastboot mode : Volume Down + Power button you will see fastboot screen and connect to PC.
11) Now close old MiFlash and run the normal one from either desktop or C:\Program Files (x86)\Xiaomi\MiPhone\MiFlash.exe or C:\Program Files\Xiaomi\MiPhone\MiFlash.exe.
12) Choose your rom folder. NOT IMAGES FOLDER ROM FOLDER !!!! ( Ex : C:\mimax).
13) Click "refresh" and this time you have to see device serial number on device tab. Now click flash and let process finish. It takes around 3-5 minute and phone will reboot by itself.
Now re-assemble your phone. DONT FORGET TO CONNECT FINGERPRINT SENSOR. Now you are totally ready.
Tried 5 times with my very own Xiaomi Mi Max 128 GB.
Different reactions
Hi,
My device could still boot on fastboot mode, and flashes successfully through it on MiFlash Beta. However, the device remains stuck on Mi logo. I've already tested flashing on EDL mode apparently successfully, with the same results. I've flashed TWRP, but the device don't enter recovery mode. What can I do? Any suggestion will be welcome.
benzersizadam said:
Many thanks for this thread, I stuck on my mi max with no reaction at anything, I read more than 100 threads, I tried testpoint, DFC (deep flash cable), click inside usb terminal to pc, windows 8, 7 10, 32 bits, 64 bits, programms like qfil (qpst), flasher tools for other phones and nothing, before with other apps at first second gives me error "can not read from port COM...", and now at least advance to 5 seconds with same error, I need to know it is neccesary too disconnect, remove two plastic cables down where places the battery
Click to expand...
Click to collapse
Working also with Hydrogen. Thanks.
@benzersizadam
This is why XDA is a great FORUM! Thank you for writing this thorough solution!
My device is up and running currently with MIUI 8! It went from a dead brick to a productive device again! I was almost giving up hope! You saved the day! It was a lot of work, but it is great seeing the device alive again.
I would just add that taking the cover off doesn't even need a tool like in the original disassembly youtube video: https://www.youtube.com/watch?v=dULcMWCEgEc
Yay!
coffee-turtle said:
@benzersizadam
This is why XDA is a great FORUM! Thank you for writing this thorough solution!
My device is up and running currently with MIUI 8! It went from a dead brick to a productive device again! I was almost giving up hope! You saved the day! It was a lot of work, but it is great seeing the device alive again.
I would just add that taking the cover off doesn't even need a tool like in the original disassembly youtube video: https://www.youtube.com/watch?v=dULcMWCEgEc
Yay!
Click to expand...
Click to collapse
Can you kindly explain some tips or secret to get unbrick cause mine is more than 4 months almost totally dead, just receive charge the battery but any signal of life in display, don´t enter recovery, fastboot, in mode EDL pc identifies like hs-usb qdownload 9008 but in 4 or 5 seconds cut conection with pc. and in my country nobody knows about Xiaomi. thanks in advance
SubwayChamp said:
Can you kindly explain some tips or secret to get unbrick cause mine is more than 4 months almost totally dead, just receive charge the battery but any signal of life in display, don´t enter recovery, fastboot, in mode EDL pc identifies like hs-usb qdownload 9008 but in 4 or 5 seconds cut conection with pc. and in my country nobody knows about Xiaomi. thanks in advance
Click to expand...
Click to collapse
Hi @SubwayChamp Everything I did was in the post and video from above in the first post by benz....
His instructions were perfect along with the youtube video. It's tricky, true, but with patience you can go through the steps and get your device running again. I was so glad that @Qulox gave me this link to this thread.
As you go through the steps, if you get stuck, we can try to give you advice.
This works for Hydrogen as well.
Many thanks
I have two dead mi max. One 128gb helium and one 32gb hydrogen.
128gb helium is completely lifeless. No charging led, no vibrations, no fastboot mode. Though i could bring it up to edl mode showing right qualcomm device in device manager. I tried flashing stock rom as mentioned in this guide which rather went successful without giving any error, even while battery connector was removed.
But mobile is still in same lifeless condition. Other than flashing process going through, it didnt make any difference. Dont know whats wrong. Also i didnt have to use two miflash versions as mentioned in steps as flashing process didnt give any error.
32gb hydrogen, boots up in flashboot mode, shows charging led, mi logo even edl model worked without any issue. It even boots up, but gives error of encryption unsuccessful asking me to reset device. I tried factory reseting it. Tried flashing twrp and wiping, formatting data, changing file system to all formats like fat, f2fs, ext1, ext2, ext3, ext4. Tried flashing crdoid and RR based on orea. Nothing working.
With twrp it keeps bootlooping showing mi logo. And with stock rom, recovery shows up encryption error. Followed procedure mentioned in this guide as well.
Is there anything am i missing or can do? Btw, bootloader is locked for both the devices. I could flash twrp referring another guide which suggested to replace stock recovery in rom files/ folder and flashing it like stock rom through miflash tool.
Battery problems? in the 128 especially?
If "nothing works" through any normal software methods, the ram &/or ROM memory chips might have become semi-defect. They are not eternal . . .
cobben said:
Battery problems? in the 128 especially?
If "nothing works" through any normal software methods, the ram &/or ROM memory chips might have become semi-defect. They are not eternal . . .
Click to expand...
Click to collapse
Tried replacing battery as well. Surprising thing is completely dead 128gb helium does boot up in edl mode with flashing working perfectly file in miflash tool. Dont know how reliable that software is.....
Hello,
trying with both Helium & Hydrogen. Still on error like say these logs.
log#1
Code:
[0,02 COM7]:[COM7]:start flash.
[0,02 COM7]:received hello packet
[0,02 COM7]:can not found programmer file.
log#2
Code:
[0,00 COM7]:[COM7]:start flash.
[2,03 COM7]:cannot receive hello packet,MiFlash is trying to reset status!
[4,56 COM7]:cannot receive hello packet,MiFlash is trying to reset status!
[7,11 COM7]:try to reset status.
[7,13 COM7]:Switch mode back
[7,13 COM7]:cannot receive hello packet,MiFlash is trying to reset status!
[7,14 COM7]:Riferimento a un oggetto non impostato su un'istanza di oggetto.
Hope anyone can help me. What's my wrong following the guide.
Thanks
harpy.eagle said:
Tried replacing battery as well. Surprising thing is completely dead 128gb helium does boot up in edl mode with flashing working perfectly file in miflash tool. Dont know how reliable that software is.....
Click to expand...
Click to collapse
Hi there.. The link of video & image of test points is not working. Can anybody please share working links
Hi there.. The link of video & image of test points is not working. Can anybody please share working links
rizkhan77 said:
Hi there.. The link of video & image of test points is not working. Can anybody please share working links
Click to expand...
Click to collapse
This is the video of Test Point https://youtu.be/SqcVY8IWkZI
benzersizadam said:
Ok guys here is the step by step even for noobs how to unbrick Xiaomi Mi Max (helium).
If you have access to fastboot jump to step 11
Requirements :
* MiFlash Beta :Download Here
* MiFlash 20151028 : Download Here
* Global Fastboot Rom : Download Here
* Xiaomi Qualcomm Drivers
* Screw and tools.
* Paper clip or cable
* For sure Usb Cable.
Now if you all ready lets continue repair. First of all you need to open back cover.
1) Open Back cover and disconnect fingerprint sensor and battery. Dont connect battery till you finish whole process. (How to disassemble video : https://www.youtube.com/watch?v=YMG04GqVU_0&t=64s)
2) Make a paper clip to setup short circuit in your mainboard. Here are the testpoints. https://s15.postimg.org/s0j0qhq3v/Xiaomi_Max_Test_Points.png
3) Ok here is the hardest and trickiest one. While you are holding paper clip or cable with those testpoint you need to connect phone to pc. My suggestion 1st connect usb cable to phone then make short circuit then connect to pc.
* One more time you need to connect phone to pc while those two testpoints connected to eachother with a paperclip or a cable.
4) Here is the second tricky part. Unzip rom file. Important part is the name of folder. Please try to make it as short as possible.
Ex : C:\mimax\
So after extraction your folder will looks like this : http://oi63.tinypic.com/334rr11.jpg
5) You need to install both MiFlash versions. They are 2 different software so you shouldnt see any errors like "it is already installed".
6) Go To C:\XiaoMi\XiaoMiFlash and run XiaoMiFlash.exe as an administrator. Click browse and choose your rom folder. NOT IMAGES FOLDER ROM FOLDER !!!! ( Ex : C:\mimax)
7) Click "refresh" you will see COM port and click "flash" If you dont see any COM port here first check if you installed drivers correctly. If drivers are installed correct please go back to step 3 and try again.
8) Install will start and continue and %99 possibly it will stop in the middle You will receive Max buffer 256 error. No worries just keep calm and take deep breath. Go to next step
9) Disconnect usb cable from pc and phone. Reconnect battery. Now voila phone will ready to work BUT NOT READY TO WORK FLAWLESS. So now put your phone to fastboot mode. Yes you read correct now your phone will be in fastboot mode even it could be ready to use but just wait for next step.
10) Fastboot mode : Volume Down + Power button you will see fastboot screen and connect to PC.
11) Now close old MiFlash and run the normal one from either desktop or C:\Program Files (x86)\Xiaomi\MiPhone\MiFlash.exe or C:\Program Files\Xiaomi\MiPhone\MiFlash.exe.
12) Choose your rom folder. NOT IMAGES FOLDER ROM FOLDER !!!! ( Ex : C:\mimax).
13) Click "refresh" and this time you have to see device serial number on device tab. Now click flash and let process finish. It takes around 3-5 minute and phone will reboot by itself.
Now re-assemble your phone. DONT FORGET TO CONNECT FINGERPRINT SENSOR. Now you are totally ready.
Tried 5 times with my very own Xiaomi Mi Max 128 GB.
Click to expand...
Click to collapse
hi, could someone share with me the miflash beta? I can download the rest but I cannot download the beta one.
thanks
Wanted to say thank you was able to recover my mi max 64gb unit.
WHAT IS HARD-BRICK?
The Hard-Brick, translated means device NULL, without function neither one! This happens a lot for forced updating: AS ANDROID 4.4.4 FOR 5xx ....
Most of the time, the cell phone stays in BOOTLOOP (infinite loop), another case as hard brick gets on the black screen with LED access.
Then you ask me?
Wagner, I Brickei my device, how to recover?
YES! There is always a way to recover. More remembering that each device has a way of doing, some are easier and others more complicated. We just need to find the right files.
So let's go!
MOTOROLA DRIVER
Drivers required for device recognition on PC.
If you have already installed, you do not have to install again.
Download
HAND-BRICK.exe
It will install the drives, recover the cell phone and recover the fastboot.
Download
STEP BY STEP
1- Turn off the phone and enter the fastboot mode:
Yes, I know the phone is off!
Plus the device is in operation and we need the phone to be turned off and enter the Fastboot mode.
HOW DO I DO THAT? I discovered two ways!
- Fast and easy mode:
OPEN THE PHONE AND DISCONNES THE BATTERY, IT WILL PLACE THE FATBOOT MODE.
IF YOU MAKE ERRORS IN COMMANDS, YOU CAN GET THE FASTEST ANSWER.
- Time-consuming and need patience:
PLUG THE PHONE TO CHARGE "INTO THE SOCKET", THE LED GOES ON, WAITES THE LED OFF.
If the LED does not turn on?
SAFETY THE POWER BUTTON ON + THE DOWN VOLUME, FOR 2 SECONDS OR ACCOUNT UP TO 30!
THEN PLACE INTO THE OUTLET, AND OBSERVE THAT THE LED WILL TURN ON! And wait until the LED turns OFF.
Why did I say I had to be patient?
Well, you're going to do this straight, each made the commands go wrong.
And it will only work again if the phone restarts. Many times the LEDs do not light up among other things like not recognizing on the PC.
HOW DO I KNOW THAT IT WORKS?
When using the unbrick, it will show you a path:
EXP:
C: / USERS / NAME / DESKTOP / MOTO MAXX / PORTUGUESE [BR] / 2 - REVIVER FB / UNBRICK - 5.1> .QBOOT BLANK - FLASH
AND THEN HE SHOWS THE RECOGNIZED FILES.
When of FAILED?
(BLANK-FLASH: **********):
THE FILES WILL BE DEMANDED TO BE RECOGNIZED, THEN IN THIS CASE THE COMMANDS WILL NOT WORK! AND AI FOLLOW THE STEPS AGAIN THE LED!
OK! now that the phone is off and ready to use the unbrick.
Remember, every time you use the unbrick and appear errors, you will have to repeat the STEP to turn on the LED!
2 - Connect the device to the PC, and check that the device is being recognized as QUSB-BULK.
Search the device manager for your PC.
And look in the part (Ports (COM and LPT)) and see if you recognize the device!
3- Install the MOTOROLA + Qualcomm USB drives.
In the Device Manager will shows that the device is being recognized as QUALCOMM.
4- Choose the Unbrick option and execute the files "GO" and wait ends up to 100%
NOTE THAT: THE PHONE WILL BECOME LIFE, AND SHOW THE BOOTLOADER WITHOUT ANDROID!
If it looks like FAIL - You have to repeat STEP 1 to turn on the LED, done that, Test other files
Contains GPT.BIN files from Android 4.4.4 to the latest version 6.0.1!
CASE NOTHING WORKS USE THIS FILE "download"
1 - REMOVE THE ARCHIVE
2- EXECUTE THE FILE WITH THE NAME "GO.bat"
3- NOTHING EVEN? ENTER WITHIN THE "DATE" FOLDER AND EXECUTE THE "01 GO.bat"
4 - NOTHING EVEN? EXECUTE THE FILE "02 GO.cmd"
ONE OF THOSE FILES MUST WORK, BECAUSE THERE IS ONLY THIS FILE!
Now go to the Fastboot option and execute the files "GO"
Contains GPT.BIN files from Android 4.4.4 to the latest version 6.0.1!
THE NEW VERSION IS MARKED WITH RED!
6. Ready! the cell phone will restart with Android 5.0.2, but this one with ERROR does not connect in the WIFI!
To correct this error, turn off the phone
Enter Fastboot mode
Choose a ROM STOCK "here" and install.
If you want a customized ROM First:
Download the new version of TWRP "here"
Choose a CUSTOM ROM "here"
And the GApps according to Android Chosen "here"
READY! YOU CAN BE HAPPY AND INSTALL ANY ROM THAT YOU WANT.
REMEMBER THAT THE ROM Stock 4.4.4 CAN NOT BE UPDATED OVER.
Hope this helps!
do not forget to leave your LIKE and SHARE, leave your comment than you found.
Hi Wagner! The "HAND-BRICK.exe" download link isn't working. Could you provide a new download link, please? Thanks in advance!!!
Hi guys
At first - I tried a method given on this forum: https://forum.xda-developers.com/mi-a1/help/phone-goes-to-qualcomm-hs-usb-qdloader-t3757867
This method doesn't work for me, because after disconnect my PC doesn't recognize my phone.
Phone is in Qualcom HS-USB Diagnostics 900E mode after OTA update (Mi A1 April Update) - strange
So guys... I know there are some magicians who can do almost everything.. Any ideas what to do?
Does MiFlash recognize your phone? If not, try instaling ADB drivers nd disable driver enforcment,
To kick device out of diagnostic mode and into QDLoader you will need either:
1) A "deep flash" cable
2) Take the phone apart and bridge test points
There are guides online for both, you can Google. You can make deep flash cable yourself fairly easily with a spare USB cable. Testpoint location is found easily via Google and can be bridged with tweezers or small flat-head screwdriver.
I did NOT have success with deep flash cable myself, I had to use testpoint method (and sadly broke my LCD in the process). The deep flash issue might of been because I was in Windows 10 x64 or on a USB3 port. If you do go that route and can't get it working, try with a Windows 7 x86 VM and USB2 passthrough mode before last resort of taking device apart.
Hold power button for 20 sec then volume down and fastboot will apear
1. install all necessary drivers (adb, qualcomm's HS-USB Diagnostics 900E, xiaomi flash tool)
2. use test point method as suggested by @CosmicDan - lots of tutorial on web on how to do this. Carefully read this before actually attempting it.
3. When you successfully do the test point method you will hear the device recognized sound on your computer
4. when you hear it, open miflashtool and your device should show up in it.
5. if not, reboot your PC. You should reboot your PC after installing all the drivers. See #1. (reboot required)
6. Once you successfully see your device on miflashtool, you can flash the fastboot rom of your choice.
7. (you might get stuck on "Can't receive hello packet" dialogue which will prevent your device from flashing), in that case change the USB port, possibly to USB 2.0 and try the test point flash method again to get detected and try flashing again.
8. Test point method should be done everytime you disconnect the USB from your phone and computer, hopefully you only need to do it twice.
9. Sadly for me, I am still unable to flash stock roms with this method, my problem is kind of unique, after flashing it shows me "Your phone is destroyed, press power to turn off" dialogue. lmao
10. if you get the same message then you dun goof'd. Hopefully yours will successfully flash.
Oh and only one version of fastboot ROM actually revives the phone, other fastboot roms actually puts it to coma (vibrating every one second, no display, no nothing). Only one fastboot ROM allows me to go to fastboot and flash recoveries. But if I flash any ROM (stock or custom) it kills the phone again and I have to repeat the given method and try again with another rom. I think the phone is effectively dead. What a **** phone! lol
udaan said:
1. install all necessary drivers (adb, qualcomm's HS-USB Diagnostics 900E, xiaomi flash tool)
2. use test point method as suggested by @CosmicDan - lots of tutorial on web on how to do this. Carefully read this before actually attempting it.
3. When you successfully do the test point method you will hear the device recognized sound on your computer
4. when you hear it, open miflashtool and your device should show up in it.
5. if not, reboot your PC. You should reboot your PC after installing all the drivers. See #1. (reboot required)
6. Once you successfully see your device on miflashtool, you can flash the fastboot rom of your choice.
7. (you might get stuck on "Can't receive hello packet" dialogue which will prevent your device from flashing), in that case change the USB port, possibly to USB 2.0 and try the test point flash method again to get detected and try flashing again.
8. Test point method should be done everytime you disconnect the USB from your phone and computer, hopefully you only need to do it twice.
9. Sadly for me, I am still unable to flash stock roms with this method, my problem is kind of unique, after flashing it shows me "Your phone is destroyed, press power to turn off" dialogue. lmao
10. if you get the same message then you dun goof'd. Hopefully yours will successfully flash.
Oh and only one version of fastboot ROM actually revives the phone, other fastboot roms actually puts it to coma (vibrating every one second, no display, no nothing). Only one fastboot ROM allows me to go to fastboot and flash recoveries. But if I flash any ROM (stock or custom) it kills the phone again and I have to repeat the given method and try again with another rom. I think the phone is effectively dead. What a **** phone! lol
Click to expand...
Click to collapse
Did you do factory flash mode? That's the only one that can recovery it, the other scripts won't flash everything.
Note that because you didn't backup partitions you will also wipe the IMEI, or so I've read (I backed up my whole device via emmcdl before brick so I was able to recover fine without miflash)
CosmicDan said:
Did you do factory flash mode? That's the only one that can recovery it, the other scripts won't flash everything.
Note that because you didn't backup partitions you will also wipe the IMEI, or so I've read (I backed up my whole device via emmcdl before brick so I was able to recover fine without miflash)
Click to expand...
Click to collapse
Actually I think I got scammed. It is Mi5x sold as MiA1. ****ing chinks! Anyway, I managed to install (Tiffany) on it and now it is booting to boot logo and bootlooping. I can get to fastboot and default (MIUI's) recovery by pressing button combos. But OEM is locked now so I cannot flash TWRP or other ROMs in it. I will have to EDL flash back to that MIA1 ROM to get it unlocked from fastboot. Otherwise MIUI unlocker asks me to link my miui account to this phone by going to settings, which I can't do because it is not booting up.
funny situation.
Bruce666 said:
Hi guys
At first - I tried a method given on this forum: https://forum.xda-developers.com/mi-a1/help/phone-goes-to-qualcomm-hs-usb-qdloader-t3757867
This method doesn't work for me, because after disconnect my PC doesn't recognize my phone.
Phone is in Qualcom HS-USB Diagnostics 900E mode after OTA update (Mi A1 April Update) - strange
So guys... I know there are some magicians who can do almost everything.. Any ideas what to do?
Click to expand...
Click to collapse
Facing The same Issue
---------- Post added at 10:42 AM ---------- Previous post was at 10:35 AM ----------
Phone Showing Charging Only
Can't Even Transfer Data
Not Detected on Pc
udaan said:
1. install all necessary drivers (adb, qualcomm's HS-USB Diagnostics 900E, xiaomi flash tool)
2. use test point method as suggested by @CosmicDan - lots of tutorial on web on how to do this. Carefully read this before actually attempting it.
3. When you successfully do the test point method you will hear the device recognized sound on your computer
4. when you hear it, open miflashtool and your device should show up in it.
5. if not, reboot your PC. You should reboot your PC after installing all the drivers. See #1. (reboot required)
6. Once you successfully see your device on miflashtool, you can flash the fastboot rom of your choice.
7. (you might get stuck on "Can't receive hello packet" dialogue which will prevent your device from flashing), in that case change the USB port, possibly to USB 2.0 and try the test point flash method again to get detected and try flashing again.
8. Test point method should be done everytime you disconnect the USB from your phone and computer, hopefully you only need to do it twice.
9. Sadly for me, I am still unable to flash stock roms with this method, my problem is kind of unique, after flashing it shows me "Your phone is destroyed, press power to turn off" dialogue. lmao
10. if you get the same message then you dun goof'd. Hopefully yours will successfully flash.
Oh and only one version of fastboot ROM actually revives the phone, other fastboot roms actually puts it to coma (vibrating every one second, no display, no nothing). Only one fastboot ROM allows me to go to fastboot and flash recoveries. But if I flash any ROM (stock or custom) it kills the phone again and I have to repeat the given method and try again with another rom. I think the phone is effectively dead. What a **** phone! lol
Click to expand...
Click to collapse
Im sorry, exactly with which ROM did you get to the fastboot?
Press power button for 15 sec
If you feel vibration then you are so lucky
boshell said:
Im sorry, exactly with which ROM did you get to the fastboot?
Click to expand...
Click to collapse
Fastboot rom for Mi5x because the phone is Mi5x.