Related
First of all, i have read some similar threads about this, and all advise diffrent solution besides the hardware mod, I have tried for 2 days all methods in Miui forums and none have worked for me except the hardware method.
My Device: Xiaomi Redmi Note 3 Pro / SD version.
State:
-would only show "Mi" logo when powered on.
-Would enter only Fastboot.
- No EDL mode
- No recovery
-bootloader locked
-In this state, you can't flash absolutely nothing with any software. (from fastboot).
Requirements:
- windows 7/ windows 10 x64 edition.
- ONLY LATEST version of miflash, from 2016 onward, so it has the required drivers and methods to work with the phone. (I have tried with older versions and it did not work, i thought there was no hope for my phone).
- one hard bricked Redmi Note 3 Pro
- any fersion of Stable FASTBOOT OFFICIAL rom. (.tgz extension) - I personally used kenzo_global_images_V7.2.3.0.LHOMIDA_20160129.0000.14_5.1_global_c85ba6c524.tgz
- medium disassembly skills,
- a lot of patience,
- minimum set of tools (one small cross screwdriver, 1-2 strong finger nails, good eyesight).
- one microusb cable
HOW TO:
1. uninstall all drivers and software related to the Xiaomi phone. (I ended up reinstalling windows 7 just to be sure all was gone - that is how desperate I became). To be sure this is done correctly, with the phone turned off, connect it to the computer.
Go into device manager, search in com ports, or wherever any drivers are installed for the phone, and uninstall all of them, ticking remove driver files also.
after doing this, hit refresh, and see if any drivers get installed again.
Repeat until there are no drivers installed, and the device will be without a driver.
2. Disconnect the phone and RESTART WINDOWS
3. Disable driver signature verification/enforcement:
a. in windows 7, this is easy: restart windows, hit f8 until a menu pops up where you can choose disable driver signature verification/enforcement.
b. in windows 10, it is a little bit longer, but: http://www.howtogeek.com/167723/how...8.1-so-that-you-can-install-unsigned-drivers/ - Be careful, when choosing the option in the last menu, use F... keys, not number keys.
4. while in windows, in the bottom right corner, there should be a message saying "test mode"
5. install ONLY the LATEST VERSION of Miflash! you may get some messages about driver installation (2 times), allow installation!
6. RESTART WINDOWS
7. Prepare the phone!: I followed the video here, even I did not understand the language: http://choimobile.vn/threads/video-...o-snapdragon-650-fix-download-mode-edl.65098/
- First, I used my nail to open the phone up, just like in the video. It is great that the screen is not glued to the body, there are only some clips holding it in place!
- after opening the cover please be careful - there is a cable connecting the case to the mainboard - the fingerprint sensor.
- after this, unscrew the 7 or 8 screws as in the video.
- unlock the cables as in the video - please be sure not to disconnect all the cables.
- now, first get the antenna plastic cover outside of the way.
- after disconnecting the camera module, I would personally advise you to get the camera out of the way first, as there is a piece of foil glued between the mainboard and the underneath of the camera module (on the display)
- with great care, rise the Mainboard from the display.
- to have better access to the testpoint pins, I turned the Mainboard over the battery.
- now, connect the microusb cable to the phone.
8. connect the phone to the computer.
9. go into device manager and check if there are any devices installed, there should be under ports.... a device called Qualcomm HS-USB Diagnostics 900E.
10. Now comes the tricky part, switching the phone to EDL mode (emercency download)
look on the back of the motherboard of the phone to connect the 2 testpoint pins as in the video. You can use anything to do this. a metal wire, a small scissors, an untied paperclip... You will have to do this while device manager is opened, as you must check it when the driver changes to "qualcomm hs-usb qdloader 9008".
Please be careful when trying to connect the 2 pins not to touch any metal housing, ans this will restart the device each time.
Now, try and try and try until the driver changes to "qualcomm hs-usb qdloader 9008".
11. unzip the rom using 7 zip to a destination of your choosing. I advise as short destination as possible and no spaces used in the folder naming. I unpacked it in C:\rom\
12. Open Miflash
13. As per other many many instructions:
a. click browse - select the folder where you unpacked the rom (for me, c:\rom\)
b. click the arrow next to brows button and select advanced.
c. in the first field, navigate to the folder where the rom was unpacked and select flashall.bat
d. in the third field select prog_emmc_firehose_8976_ddr.mbn from the "images"folder in the folder whre he rom was extracted
e. field 7: rawprogram0.xml and field8: patch0.xml
f. Hit the Refresh button, the device should appear as a com port in the white field of Miflash.
g. just to be sure, tick also "flash all" in the bottom of miflash.
14. Hit the Flash button on Miflash and this should be the last step before powering up your revived Xiaomi Redmi Note 3.
This is what I learned in the past 2-3 days.
Different errors I got during the learning process and what i did to avoid them:
- different problems with drivers not installing correctly or showing different device names - just use the method i pointed out in the beginning to uninstall any driver previously installed on the computer, with the refresh in device manager and than uninstalling all.
- "end of package" error at second 2 while flashing in Miflash - you are using an older or an unsupported version of miflash, just use the latest one.
- not being able to flash anything while in fastboot - if you have a locked bootloader, on redmi note 3 snapdragon version, you simply won't be able to flash anything. end of story. this is the whole purpose of having a locked bootloader.
- trying to go into EDL mode using fastboot comand "fastboot oem eld" - this will not work for a really bricked device as was mine. the only solution is to go through the tespoint pin connection.
i wonder if there's a way not to make trwp locked in the recovery partition, so if someone flashes a factory rom without precaution, twrp will simply get overwritten by factory recovery. Wouldn't that prevent these hard bricks?
btw, nice guide
Please move the thread into guides/tutorial section.
Well, mine was bricked too 2 days ago... even I already unlock the bootloader using the official way.
It happened because I'm on AOSP and I flash Xiaomi.EU ROM from TWRP.
'MI' Logo flashed twice then the phone turns off itself.
It can't boot, can't enter EDL mode. I just can go into fastboot mode. But nothing can be done there because it always says 'device is locked'.
'fastboot oem device-info' also says the phone is on locked state.
Dunno why this happen, I think its because I play with the unlock bootloader toggle on previous MIUI and AOSP ROM.
After countless of times trying to get into EDL, I give up.
Device manager always show "QCom HS-USB Diagnostic 900E" instead of "QCom HS-USB QLoader 9008"
Finally I try the official Mi Unlock software, re-unlock success and BAM... Phone boots again into system. lol...
This makes me think the bricked problem can prevented/solved to by:
- At least bind a Xiaomi Account to your phone once when using official ROM (recommended China Dev ROM)
- Use that account to apply for the unlock, and when you got the phone bricked/relocked, you can re-unlock it using official way to revive the phone
Now is possible unbrick without disassembly:
http://en.miui.com/thread-267263-1-1.html
http://www.htcmania.com/showthread.php?t=1174700
jujusito said:
Now is possible unbrick without disassembly:
http://en.miui.com/thread-267263-1-1.html
http://www.htcmania.com/showthread.php?t=1174700
Click to expand...
Click to collapse
please read through all the thread, don't just throw in a link. the method mentioned by you will not work on some bricked devices, including mine. this did not work for me, so I ended up disassembling the phone.
aabenroi said:
Well, mine was bricked too 2 days ago... even I already unlock the bootloader using the official way.
It happened because I'm on AOSP and I flash Xiaomi.EU ROM from TWRP.
'MI' Logo flashed twice then the phone turns off itself.
It can't boot, can't enter EDL mode. I just can go into fastboot mode. But nothing can be done there because it always says 'device is locked'.
'fastboot oem device-info' also says the phone is on locked state.
Dunno why this happen, I think its because I play with the unlock bootloader toggle on previous MIUI and AOSP ROM.
After countless of times trying to get into EDL, I give up.
Device manager always show "QCom HS-USB Diagnostic 900E" instead of "QCom HS-USB QLoader 9008"
Finally I try the official Mi Unlock software, re-unlock success and BAM... Phone boots again into system. lol...
This makes me think the bricked problem can prevented/solved to by:
- At least bind a Xiaomi Account to your phone once when using official ROM (recommended China Dev ROM)
- Use that account to apply for the unlock, and when you got the phone bricked/relocked, you can re-unlock it using official way to revive the phone
Click to expand...
Click to collapse
I also applied for an unlock code, but this takes up to 15 days, and I have the phone for only 3 days . I could not wait for the code, I had to do something to revive it.
meangreenie said:
i wonder if there's a way not to make trwp locked in the recovery partition, so if someone flashes a factory rom without precaution, twrp will simply get overwritten by factory recovery. Wouldn't that prevent these hard bricks?
btw, nice guide
Click to expand...
Click to collapse
I made a modified TWRP which will not cause hard bricks
Rajdip said:
I made a modified TWRP which will not cause hard bricks
Click to expand...
Click to collapse
great work! your modded twrp will no doubt save me when i forget i have to delete the emmc file in the future.
Dear, thank you for your contribution, this deserves to be a section more important, really saved my phone from the hard brick. Again very grateful
how do i know what a test point looks like on any phone? like the new redmi 3s? i cant get into edl because im stuck in Qualcomm HS-USB Diagnostics 900E
xdarkmario said:
how do i know what a test point looks like on any phone? like the new redmi 3s? i cant get into edl because im stuck in Qualcomm HS-USB Diagnostics 900E
Click to expand...
Click to collapse
maybe look for something like this?
http://choimobile.vn/Temp/Testpoint_Redmi_Note3_PRO_3.jpg
I doubt they will have much variance from xiaomi phone to phone to make it easy for factory / repair centers to fix many models... (I could be wrong though), other brands are probably different.
Well you can enter edl mode from fastboot via this simple tool
http://forum.xda-developers.com/and.../guide-how-to-reboot-to-edl-fastboot-t3394292
And then you can flash any miui .tgz based rom and resurrect.
I hard bricked my Device last night and resurrected
PS : you must have the MiPcSuit installed
ilvmyname said:
Well you can enter edl mode from fastboot via this simple tool
http://forum.xda-developers.com/and.../guide-how-to-reboot-to-edl-fastboot-t3394292
And then you can flash any miui .tgz based rom and resurrect.
I hard bricked my Device last night and resurrected
PS : you must have the MiPcSuit installed
Click to expand...
Click to collapse
links dead
Quick addition: if you're using Virtual Box, like me (on a mac), you need to enable USB 2.0 on the virtual machine. On Virtual Box, this means you have to add an extension pack. This might save you 48hrs, like it cost me
DO NOT FLASH HYDROGEN ROMS ON HELIUM, OR YOU GONNA HAVE A HARDBRICK.
IN CASE YOU HAVE ONE, HERE IS THE SOLUTION.
This was tested with Xiaomi Mi Max 128GB helium and localized rom from xiaomi eu.
I am not responsible for bricked devices or anything else. So at your own risk:
1. Install official MiPhone drivers
2. Download and install MiFash beta.
3. Download and unpack TWRP for miflash: 32gb or 64-128gb thanks @Abdess76.
4. Download ROM for your device, I recommend to try this one. You can install RR/CM Rom as well.
5. Run MiFlash with admin rights.
6. Turn off the phone, plug the cable to PC and halfway to the phone.
7. At the same time press Volume + and Volume - and plug in the cable.
8. Refresh MiFlash phone should show up. (If it didn't then make sure you did it right and u got drivers)
9. Navigate to your unpacked TWRP and flash it.
10. Now, boot ur phone with volume up. It's a bit slow. If it's stuck on miui logo, just release button and wait.
From here start to pay more attention:
11. TWRP can ask for password, press cancel and allow modifications by moving slider.
If you just need ROOT and your current rom, skip to the step 16. Also there is a recovery from boot in system folder. If you won't remove it, recovery may be replaced with stock one after reboot. Keep it that way if you want OTAs.
12. Format data.
13. Enable MTP and put modified zip in your phone.
14. Go to mounts and unmount system **
15. Flash your rom.
16. Flash latest supersu.
17. Reboot the phone.
In case u got NO OS message, then it means that u probably ignored step 15.
Also first boot may take like 15-20 minutes, since eu rom is deodexed.
Just to be sure, after installation mount system partition and navigate to the /system folder using TWRP's file manager and make sure it's not empty.
* In my case system didn't install because script could mount system partition since it was already mounted.
P.S. In order to update, you need to install OTA for offical rom via TWRP. Then without rebooting flash SuperSU, and finally using TWRP's file manager navigate to system folder and delete file named recovery from boot. Doing so will keep root and recovery.
Thank you so much for the guide! I will try it tonite
Waiting for boot loader is just too long..
WOW!!!! Just, wow..... I can not believe it but it worked like a charm. It took me forever to figure out my issue with the drivers, but after solving that I followed you step-by-step. And, lo and behold, it WORKED! Note for other users, Twrp took about a minute or two to finally boot up and it took me personally about 15-20 minutes before MIUI 8 finally booted. Just wait it out and you should have the amazing results that Doom Slayer has so graciously provided you
THANK YOU!!!!
I just done following your guide and it works!!
For rooting, I tried 2 times before it works. I believe you missed out a step to mount back system before flashing supersu.
So in the future, how do we dirty flash? Start from step 13?
How about clean flash? Start from step 12?
Thank you once again for this great guide!!
You saved me a lot of time waiting for Bootloader approval.
flywithme said:
I just done following your guide and it works!!
For rooting, I tried 2 times before it works. I believe you missed out a step to mount back system before flashing supersu.
So in the future, how do we dirty flash? Start from step 13?
How about clean flash? Start from step 12?
Thank you once again for this great guide!!
You saved me a lot of time waiting for Bootloader approval.
Click to expand...
Click to collapse
Yeah, dirty flash is you keep your data and format system and caches .
Clean flash is u format data as well.
The thing is that u have root, and ur phone is also secured. It's linked to ur Mi account, while it's locked. It's better to keep that way
Theoretically If you will ignore steps from 12 to 16. (Maybe u can ignore data formatting too)
Then you can get a ROOT and TWRP on your current rom.
And also theoretically while on miui 8 rom ,u can try to unlock bootloader without waiting.
Try this manual.
I have followed these steps and bricked my phone, spent the last 24h trying to recover it no luck.
I got an error while in the process of flashing the rom at step 16, then tried again and phone went black, stopped responding.
It's not detected using adb or fast boot, it appears in device manager as "Qualcomm HS-USB QDLoader 9008" or "Qualcomm HS-USB Diagnostics 900E", I have tried to flash again TWRP or the official ROM, it says success every time but the phone is still dead.
Could it be due to locked boot loader ?
agreusar said:
I have followed these steps and bricked my phone, spent the last 24h trying to recover it no luck.
I got an error while in the process of flashing the rom at step 16, then tried again and phone went black, stopped responding.
It's not detected using adb or fast boot, it appears in device manager as "Qualcomm HS-USB QDLoader 9008" or "Qualcomm HS-USB Diagnostics 900E", I have tried to flash again TWRP or the official ROM, it says success every time but the phone is still dead.
Could it be due to locked boot loader ?
Click to expand...
Click to collapse
Open it up and remove battery for a few minutes, then try again from step 6...
agreusar said:
I have followed these steps and bricked my phone, spent the last 24h trying to recover it no luck.
I got an error while in the process of flashing the rom at step 16, then tried again and phone went black, stopped responding.
It's not detected using adb or fast boot, it appears in device manager as "Qualcomm HS-USB QDLoader 9008" or "Qualcomm HS-USB Diagnostics 900E", I have tried to flash again TWRP or the official ROM, it says success every time but the phone is still dead.
Could it be due to locked boot loader ?
Click to expand...
Click to collapse
Which rom did u flash, give the link please.
Are u sure it's for your version? It can be a broken file as well.
Does the device connects when u hold both volume buttons?
It's called emergency download mode, u can istall rom with miflasher.
There is a testpoint method also.
All u need is a pic from this post on http://4pda.ru/forum/index.php?showtopic=749580&st=700#entry51154086
U need to disconect battery, connect testpoint to battery and flash ur device with miflash.
After that let it charge, since this in your state phone consumes battery.
thanks for you answer, I flashed the MiMAXPRO EU ROM xiaomi.eu_multi_MIMAXPro_6.8.4_v8-6.0.zip (sorry as a new user not allowed to post a link yet)
When I hold both volume buttons the screen is still black but MI Flasher works with COM10, after flashing a ROM or TWRP again MIFlash says "success" but the phone is still dead and won't start up even after holding power button for a long time.
I'm happy to open the phone and try the method on the russian forum, I will try tomorrow hope it will start up
agreusar said:
thanks for you answer, I flashed the MiMAXPRO EU ROM xiaomi.eu_multi_MIMAXPro_6.8.4_v8-6.0.zip (sorry as a new user not allowed to post a link yet)
When I hold both volume buttons the screen is still black but MI Flasher works with COM10, after flashing a ROM or TWRP again MIFlash says "success" but the phone is still dead and won't start up even after holding power button for a long time.
I'm happy to open the phone and try the method on the russian forum, I will try tomorrow hope it will start up
Click to expand...
Click to collapse
Don't worry about your phone, the testpoint method will work for sure.
But in order to prevent this kind of situations ,we need to determine the reason how did it happen and you need to help me with that one by answering following questions:
1) You have mentioned that you had an error 1st time.
I also had error which was cache related, and it's OK because that partition was just formatted. You tried to flash again... but did you unmount your system partition for second time?
2) What's the capacity of your internal storage?
3) Did you use internal or external storage? If external then I need the model and the file system that have been used on that storage.
Doom Slayer said:
Don't worry about your phone, the testpoint method will work for sure.
But in order to prevent this kind of situations ,we need to determine the reason how did it happen and you need to help me with that one by answering following questions:
1) You have mentioned that you had an error 1st time.
I also had error which was cache related, and it's OK because that partition was just formatted. You tried to flash again... but did you unmount your system partition for second time?
2) What's the capacity of your internal storage?
3) Did you use internal or external storage? If external then I need the model and the file system that have been used on that storage.
Click to expand...
Click to collapse
Hello,
I managed to recover the phone, I installed a fresh windows 7 on another PC with only MI Flash Beta installed, device appeared as "Qualcomm HS-USB QDLoader 9008" as usual and I flashed the china ROM. Not sure why it wouldn't start previously after flashing, maybe issue with drivers.
1) unfortunately I don;t remember the syntax of the error, it was after a few seconds of flashing but the process seemed interrupted, I even googled it but my browser history has been purged.
2) 64GB (Helium)
3)I used internal storage, copied the zip on the phone using MTP.
Might try to go through the process again this weekend.
agreusar said:
Hello,
I managed to recover the phone, I installed a fresh windows 7 on another PC with only MI Flash Beta installed, device appeared as "Qualcomm HS-USB QDLoader 9008" as usual and I flashed the china ROM. Not sure why it wouldn't start previously after flashing, maybe issue with drivers.
1) unfortunately I don;t remember the syntax of the error, it was after a few seconds of flashing but the process seemed interrupted, I even googled it but my browser history has been purged.
2) 64GB (Helium)
3)I used internal storage, copied the zip on the phone using MTP.
Might try to go through the process again this weekend.
Click to expand...
Click to collapse
Well, I guess system was mounted and it gived u the error,but formatted it.
hi to all of you. I am very interested by this thread. Here is the story. I received my brand new mi max helium this week but it was the chinese rom. I am in France and my country did not appear in the settings. So I wanted to flash a global rom. I plugged it to my pc in recovery mode and a window appeared said that there is an update. I clicked ok and after a while I got stuck in the mi logo bootloop.
Then from then I tried everything possible from several solutions here, but nothing worked. What I got is the mi logo without bootloop, but nothing more.
I get the message that the bootloader is locked, but I can't get it unlock if it is in this state.
What I can reach is the recovery mode and the fastboot mode. But nothing else worked, flash or anything.
That is why I am interested to flash a recovery, in order to flash a clean rom, etc..
I did what you, Doom Slayer, explains, but I could not get a twrp flash. It ends with "receiving hello packet" in mi flash, and every thing stopped.
If I cannnot install any recovery, I cannot flash a rom.
So please if you have any suggestion, it would be helpful. Thanks a lot.
alain belay said:
hi to all of you. I am very interested by this thread. Here is the story. I received my brand new mi max helium this week but it was the chinese rom. I am in France and my country did not appear in the settings. So I wanted to flash a global rom. I plugged it to my pc in recovery mode and a window appeared said that there is an update. I clicked ok and after a while I got stuck in the mi logo bootloop.
Then from then I tried everything possible from several solutions here, but nothing worked. What I got is the mi logo without bootloop, but nothing more.
I get the message that the bootloader is locked, but I can't get it unlock if it is in this state.
What I can reach is the recovery mode and the fastboot mode. But nothing else worked, flash or anything.
That is why I am interested to flash a recovery, in order to flash a clean rom, etc..
I did what you, Doom Slayer, explains, but I could not get a twrp flash. It ends with "receiving hello packet" in mi flash, and every thing stopped.
If I cannnot install any recovery, I cannot flash a rom.
So please if you have any suggestion, it would be helpful. Thanks a lot.
Click to expand...
Click to collapse
Did you disable drivers signature?
Also some people have a better luck on windows 7, u can try a virtual machine.
If you can enter EDL mode, then you should be fine.
Unless Chinese already disabled it in a new update.
I would blame drivers. Make sure u got them correctly.
Updated tutorial.
Uploaded TWRP for helium, so you don't need to edit updater script anymore, since script will get correct model.
Now you can try to get root on your current rom and unlock bootloader without Xiaomi's confirmation.
People having helium with unlocked bootloader may also have problems installing roms from xiaomi eu, if they have TWRP from hydrogen.
You may update using my recovery.img from archive using fastboot, or TWRP(will also work for locked bootloader).
Doom Slayer said:
Did you disable drivers signature?
Also some people have a better luck on windows 7, u can try a virtual machine.
If you can enter EDL mode, then you should be fine.
Unless Chinese already disabled it in a new update.
I would blame drivers. Make sure u got them correctly.
Click to expand...
Click to collapse
hi Doom. Thank you for reply. But what do you mean by " disable drivers signature". I did not do anything but install the drivers and when I am on what I think is EDL mode(screen isi black) the driver is recognized as Qualcomm HS-USB QDLoader 9008(COM20).
Anyway, I will give another try and let you know. Thank you again.
---------- Post added at 09:14 AM ---------- Previous post was at 08:22 AM ----------
I followed your guide and I could get the twrp installed. So I tried to install rom(following your link). It said rebooting in 5 seconds, and then nothing. The screen is black, no power anymore, no logo, no vibes, and no life at all.
I cannot get any more reaction from it. I plugged it to my pc, but nothing is connected. I was so happy with twrp working... Any idea?...
one more information I don't know if it can help, when I flashed first, I tried the "xiaomi.eu_multi_MIMAXPro_6.8.4_v8-6.0" and a message said "failed. This rom is for helium and this is hydrogen phone". Which is strange because mine is helium(4GB/128GB).
Then I tried with the "xiaomi.eu_multi_MIMAX_V7.5.6.0.MBCCNDE_v7-6.0" rom, and everything got ok, last message "success. The phone will reboot in 5 seconds", and from then, dead all over...
alain belay said:
one more information I don't know if it can help, when I flashed first, I tried the "xiaomi.eu_multi_MIMAXPro_6.8.4_v8-6.0" and a message said "failed. This rom is for helium and this is hydrogen phone". Which is strange because mine is helium(4GB/128GB).
Then I tried with the "xiaomi.eu_multi_MIMAX_V7.5.6.0.MBCCNDE_v7-6.0" rom, and everything got ok, last message "success. The phone will reboot in 5 seconds", and from then, dead all over...
Click to expand...
Click to collapse
Looks like you installed hydrogen TWRP and that caused all your problems.
I've been very careful to install the helium twrp from this thread...
Hey guys, I have a A2017 axon 7, and I tried to upgrade from Marshmalow to nougat by flashing the B04 update from TWRP. I have now the factory recovery mode, and when I try to go in fastboot, it tries to launch the bootloader( which just tells me that my device software cannot be checked for corruption and that I need to lock my bootloader). When I try to boot normally it stays on the same "bootloader screen" and tells me to press the start button which makes the phone display the linux logo.... I'm a bit lost, I'm on ArchLinux could you pls help me ?
Thx !
Dr_Raider said:
Hey guys, I have a A2017 axon 7, and I tried to upgrade from Marshmalow to nougat by flashing the B04 update from TWRP. I have now the factory recovery mode, and when I try to go in fastboot, it tries to launch the bootloader( which just tells me that my device software cannot be checked for corruption and that I need to lock my bootloader). When I try to boot normally it stays on the same "bootloader screen" and tells me to press the start button which makes the phone display the linux logo.... I'm a bit lost, I'm on ArchLinux could you pls help me ?
Thx !
Click to expand...
Click to collapse
Well, you should use MiFlash and install the stock system through EDL. The problem is that MiFlash is for Windows x64. if you could get a win10 x64 pc, you could fix it in a minute.
Or get to the recovery if you can, and flash Nougat again but via an SD card. But maybe you won't be able to get to the recovery mode
Choose an username... said:
Well, you should use MiFlash and install the stock system through EDL. The problem is that MiFlash is for Windows x64. if you could get a win10 x64 pc, you could fix it in a minute.
Or get to the recovery if you can, and flash Nougat again but via an SD card. But maybe you won't be able to get to the recovery mode
Click to expand...
Click to collapse
I need help! I wanted to relock the bootloader but then I coulnd't enter the recovery or fastboot anymore. When I press any combination it always turn on for 1 sec and then the screen turns off again but it still GOT recognized as QUSB Bulk. After I installed MiFlash the device is recognized as QDLOADER 9008. I didn't flash anything and I don't kno how to unbrick my device now .
I use the A2017G model btw.
Kantastisch said:
I need help! I wanted to relock the bootloader but then I coulnd't enter the recovery or fastboot anymore. When I press any combination it always turn on for 1 sec and then the screen turns off again but it still GOT recognized as QUSB Bulk. After I installed MiFlash the device is recognized as QDLOADER 9008. I didn't flash anything and I don't kno how to unbrick my device now .
I use the A2017G model btw.
Click to expand...
Click to collapse
How did you relock the bootloader? If you used a guide, you should have found a warning, and if you used axon7toolkit a message should've popped up.
You messed up. Real bad. You are probably on DFU mode, and the only ways to get out of there are:
-discharge the battery completely and try to enter FTM mode (i think you have to do that while it is connected to a PC), I think it was with volume down + power. this method works for very few people. If you enter ftm mode, issue 'adb reboot edl' and use MiFlash right away with a FULL_EDL package
-use the 4th category brick repair manual (disassemble the phone, short some pins)
Choose an username... said:
How did you relock the bootloader? If you used a guide, you should have found a warning, and if you used axon7toolkit a message should've popped up.
You messed up. Real bad. You are probably on DFU mode, and the only ways to get out of there are:
-discharge the battery completely and try to enter FTM mode (i think you have to do that while it is connected to a PC), I think it was with volume down + power. this method works for very few people. If you enter ftm mode, issue 'adb reboot edl' and use MiFlash right away with a FULL_EDL package
-use the 4th category brick repair manual (disassemble the phone, short some pins)
Click to expand...
Click to collapse
I think DFU Mode is when I get recognized as ZTE Handset diagnostic .... according to this guide : https://forum.xda-developers.com/axon-7/how-to/a2017-4th-category-brick-repair-manual-t3585898) It's a2017 but still.
"Axon 7 restore manual from bricked conditions when only ZTE Handset Diagnostic Interface(DFU) (COM...) mode is detected"
But I get recognized as QDloader 9008 and miflash also recognizes it as com10 or something.
Kantastisch said:
I think DFU Mode is when I get recognized as ZTE Handset diagnostic .... according to this guide : https://forum.xda-developers.com/axon-7/how-to/a2017-4th-category-brick-repair-manual-t3585898) It's a2017 but still.
"Axon 7 restore manual from bricked conditions when only ZTE Handset Diagnostic Interface(DFU) (COM...) mode is detected"
But I get recognized as QDloader 9008 and miflash also recognizes it as com10 or something.
Click to expand...
Click to collapse
it's not necessarily like that. DFU mode is just a mode in which the phone can be. Sometimes Windows just installs the QDLoader driver even though it's not EDL. and if you tried miflash and it didn't work, then it's most probably that.
There's a way to check. If you go to Properties, there should be a number that identifies the mode. if you google it and 'dfu interface' appears, then you are dfu-bricked
But if you locked the bootloader without being fully stock then it's most probably dfu bricked anyways
Again, how did you lock the bootloader?
I don't actually know if I really locked the bottloader.
So, I had unlocked bootloader and twrp. I just bootet into the bootloader, typed "fastboot oem lock" in adb and it said OK on the PC.
But on the phone it never asked me if I want to lock it or anything. And I never said MiFlash isn't working. It recognizes my phone but i judt didn't TRY to flash anything because I didn't want to make the situation even worse perhaps
Choose an username... said:
it's not necessarily like that. DFU mode is just a mode in which the phone can be. Sometimes Windows just installs the QDLoader driver even though it's not EDL. and if you tried miflash and it didn't work, then it's most probably that.
There's a way to check. If you go to Properties, there should be a number that identifies the mode. if you google it and 'dfu interface' appears, then you are dfu-bricked
But if you locked the bootloader without being fully stock then it's most probably dfu bricked anyways
Again, how did you lock the bootloader?
Click to expand...
Click to collapse
I don't actually know if I really locked the bottloader.
So, I had unlocked bootloader and twrp. I just bootet into the bootloader, typed "fastboot oem lock" in adb and it said OK on the PC.
But on the phone it never asked me if I want to lock it or anything. And I never said MiFlash isn't working. It recognizes my phone but i judt didn't TRY to flash anything because I didn't want to make the situation even worse perhaps
Kantastisch said:
I don't actually know if I really locked the bottloader.
So, I had unlocked bootloader and twrp. I just bootet into the bootloader, typed "fastboot oem lock" in adb and it said OK on the PC.
But on the phone it never asked me if I want to lock it or anything. And I never said MiFlash isn't working. It recognizes my phone but i judt didn't TRY to flash anything because I didn't want to make the situation even worse perhaps
Click to expand...
Click to collapse
Lol it doesn't ask you if you want to lock it, that's the point with bootloader mode. there's no system, no UI, and you make stuff via commands.
This is why you shouldn't even attempt this kind of stuff without knowing how it works. At least if you had used axon7toolkit, it would've told you not to.
Find a FULL_EDL package for your model. If you have an A2017, simply use this one:
https://androidfilehost.com/?fid=817550096634790942
or
https://mega.nz/#!JqwEUDCa!lW3NDaBNbmMxhtw6XajspHBJaaEmLC8uNvMZS5ww0EQ
(they are the same file)
Unzip it, leave the folder somewhere handy, put the phone in what you believe is EDL, open MiFlash and select the folder, and flash
Choose an username... said:
Lol it doesn't ask you if you want to lock it, that's the point with bootloader mode. there's no system, no UI, and you make stuff via commands.
This is why you shouldn't even attempt this kind of stuff without knowing how it works. At least if you had used axon7toolkit, it would've told you not to.
Find a FULL_EDL package for your model. If you have an A2017, simply use this one:
https://androidfilehost.com/?fid=817550096634790942
or
https://mega.nz/#!JqwEUDCa!lW3NDaBNbmMxhtw6XajspHBJaaEmLC8uNvMZS5ww0EQ
(they are the same file)
Unzip it, leave the folder somewhere handy, put the phone in what you believe is EDL, open MiFlash and select the folder, and flash
Click to expand...
Click to collapse
Yeah, I screwed up, I know. But what is the point of flashing a full edl package for the phone if I have to put the phone in "what I believe id edl mode"?
And what shall I do if I succeed at something? Besided that, I can't find any EDL package for the A2017G?
https://forum.xda-developers.com/axon-7/development/edl-emergency-dl-mode-twrp-unlock-t3553514
This guide tells me NOT TO flash anything on a2017g...
Kantastisch said:
Yeah, I screwed up, I know. But what is the point of flashing a full edl package for the phone if I have to put the phone in "what I believe id edl mode"?
And what shall I do if I succeed at something? Besided that, I can't find any EDL package for the A2017G?
https://forum.xda-developers.com/axon-7/development/edl-emergency-dl-mode-twrp-unlock-t3553514
This guide tells me NOT TO flash anything on a2017g...
Click to expand...
Click to collapse
Okay let me tell you this real straight. I have done this. I have the G packages, I just thought you were the op for some reason. Look at the back of the phone and confirm whether you have an A2017G or an A2017 just in case, or you might mess up even more, as hard as that can be.
at any rate, your fears are all dumbfounded, because in the situation that you are in, you have 3 options:
a) disregard all the help that i'm trying to give you, even though I have already done the process; and keep your brick on a shelf.
b) search on google or xda yourself, then do the process, without bothering here with your lack of trust
c) follow my advice and do the damn process
Whichever option you choose, I'm gonna leave the package here:
https://mega.nz/#!UrxCRCrQ!a4sXVFu5oqct2sWStfN_luGpN5HEGXxE4FcrRteagQ4
or
https://androidfilehost.com/?fid=961840155545591863
Again, I HAVE FOLLOWED THE 4TH CATEGORY BRICK REPAIR GUIDE AND FIXED MY G. I flashed stuff through EDL at least 10 times. And there wouldn't be a bunch of EDL packages for the G if they had a 100% chance of bricking your phone
So. If you decide to do this, turn your phone off. connect the USB cable to the PC but not the phone. Hold both volume buttons (but not the power button) and insert the USB cable at the same time. Then fire up MiFlash and try to flash the file (you have to unzip the folder, then select the folder on miflash, then flash. Here 2 things may happen:
a) it flashes and you can just go bother someone else
b) it doesn't and you have to follow the 4th category brick repair guide
Simple as that. if it fails, you might want to check if the 'Qualcomm HS-USB QDLoader 9008' is actually EDL mode or DFU mode, so you can do that by going to properties and checking some device identifier number on google (haven't done that, i just read that it can be done somewhere here).
Choose an username... said:
Okay let me tell you this real straight. I have done this. I have the G packages, I just thought you were the op for some reason. Look at the back of the phone and confirm whether you have an A2017G or an A2017 just in case, or you might mess up even more, as hard as that can be.
at any rate, your fears are all dumbfounded, because in the situation that you are in, you have 3 options:
a) disregard all the help that i'm trying to give you, even though I have already done the process; and keep your brick on a shelf.
b) search on google or xda yourself, then do the process, without bothering here with your lack of trust
c) follow my advice and do the damn process
Whichever option you choose, I'm gonna leave the package here:
https://mega.nz/#!UrxCRCrQ!a4sXVFu5oqct2sWStfN_luGpN5HEGXxE4FcrRteagQ4
or
https://androidfilehost.com/?fid=961840155545591863
Again, I HAVE FOLLOWED THE 4TH CATEGORY BRICK REPAIR GUIDE AND FIXED MY G. I flashed stuff through EDL at least 10 times. And there wouldn't be a bunch of EDL packages for the G if they had a 100% chance of bricking your phone
So. If you decide to do this, turn your phone off. connect the USB cable to the PC but not the phone. Hold both volume buttons (but not the power button) and insert the USB cable at the same time. Then fire up MiFlash and try to flash the file (you have to unzip the folder, then select the folder on miflash, then flash. Here 2 things may happen:
a) it flashes and you can just go bother someone else
b) it doesn't and you have to follow the 4th category brick repair guide
Simple as that. if it fails, you might want to check if the 'Qualcomm HS-USB QDLoader 9008' is actually EDL mode or DFU mode, so you can do that by going to properties and checking some device identifier number on google (haven't done that, i just read that it can be done somewhere here).
Click to expand...
Click to collapse
THANKS SO MUCH , you saved my ass, it flashed without a problem and sorry for bothering you. Bootloader is locked now and it works fine. Thanks again!
Hello everybody,
First off, I hate people who don't search on google before making a post, I have been searching for 4 days and I feel that it's appropriate to ask now.
I will make 2 parts to this thread, one will be a very fast explanation of what I did and the second part will be the same but a very thorough with a step by step process of what I messed up...
TL;DR: I was tired, late in the evening I flashed for some reason a Partition table of a Mi Note 3 on my Mi A1... I am now bricked and cannot access anything, fastboot, ADB, recovery nothing! I guess my phone is in EDL mode cause when I plug it in it flashes its led. "Qualcomm HS-USB QDLoader 9008" Is what I see in my device manager.
What do? oh, I forgot! I cannot access anything through any combination of buttons. I am stuck here, where I am!
The full thorough explanation for people who are bothered to read fully. (Includes my excuses for making noob mistakes, might be fun to read idk.)
Young me on a Sunday evening decides to reinstall magisk but this time with twrp cause I did it without twrp (yeah yeah I know). I was left without OTA's and after uninstalling anything that had something to do with Xposed or magisk I trashed it all. and stupid me thought that maybe? maybe? just maybe deleting Dalvik Cache would help me get my OTA's back after injecting my original ROM. This is where the fun begins.
I was not wanting to go through reinstalling magisk and all that to wipe the Dalvik Cache, I thought that that was my mission now, so I decided to search for methods that don't require root or being in the system, so some kind of fastboot or ADB command or something idk. I tried installing twrp and without my understanding that failed miserably and then I read some post where someone said that they flashed a mi note 3 partition table on their phone and something worked. Being the naïve little boii that I am, let's do that hey? Bam! bricked! I read somewhere I can open the phone and remove the battery and not having the tools is a mess, having to ask friends for some and voiding my warranty for something that probably won't work and after reading I understood that I'm in "EDL 9008 recovery" or something like that. I cannot boot into anything, I only have EDL 9008 to work with. I tried using Xiaomi's flasher tool and it would never respond to the initial hello packet (duuhh! I can't use ADB nor fastboot).
I know that this was stupid, I know! I learnt my lesson. If there is nothing we can do can I at least somehow get my internal storage data back? I deleted the backups from google drive for a short amount of time but randomly 5hrs prior to this sad story. All I have safe are now my contacts.
I hope you guys have some ideas! I feel like I'm fked but maybe with EDL 9008, there is a little glimmer of light?
P.S. If you guys somehow get me into fastboot I can flash a correct partition table back. My PC has all drivers so I can do this!
Sincerely, Micheal.
There is a way although i did tried it yet.
First of all sorry for my English.
Download latest MiFlash tool and qualcomm driver, this package contain both but not latest MiFlash so you should download lastest version from official site.
https://www.fshare.vn/file/H3R8M6OMRP2R
Download lastest stock rom.
You will need a good USB type C cable, dont use the one come with phone because you dont want to cut it in half.
Yes, that exactly what i said. Cut it in half, there are 4 small wire (or maybe 5 with type C?), remove it outer plastic and reconnect them.
Join the green and black cable, like you short circuit them, then plug your phone into PC with that cable without release green and black, wait for 5 sec then seperate them, the green and black.
Check device manager on your PC, you should hear device connect sound and qualcomm HS-USB QDLoader show up under Ports.
Open MiFlash and try to flash it.
You may want to check this video, although it in Vietnamese but you should understand the usb cable part.
https://www.youtube.com/watch?v=d5-1I9rWTiw
Hi, interesting situation. What about following this guide: http://en.miui.com/thread-235865-1-1.html ?
Its for some other phone, but try instaliing some drivers and you may get some signal of life.
Very interesting
I have thought about doing this as I had an old type-c lying around that came with the phone (I use a beautiful cable I bought off amazon) and saw this method to flash but never tried it..
I'll give it a go thanks.
btw. Your English is good I understood everything
The second comment from TrueMS:
I already have all drivers installed and in the long post I said that I have a flashing led that indicates that i'm in EDL 9008, the phone isn't dead but it won't turn on with any driver
m1shka said:
Very interesting
I have thought about doing this as I had an old type-c lying around that came with the phone (I use a beautiful cable I bought off amazon) and saw this method to flash but never tried it..
I'll give it a go thanks.
btw. Your English is good I understood everything
The second comment from TrueMS:
I already have all drivers installed and in the long post I said that I have a flashing led that indicates that i'm in EDL 9008, the phone isn't dead but it won't turn on with any driver
Click to expand...
Click to collapse
Yes, thats what I meant. Well, I dont know how to help you, wish you luck. I remember how I flashed wrong ROM for my S3 Mini and it was completly trashed, I'm glad that Xiaomi gives us at least some signs of life and hope.
And btw. I would rather charge the phone somehow - I hope it charges even in EDL mode, because if your phone dies while flashing with MiFlash, things can be even worse.
EDIT: I also found this guide, you can try it out: https://forum.xda-developers.com/g4/general/guide-unbrick-via-external-sdcard-qfil-t3748946
Okay so now a major reply!
I have stated in the OP that I am already in EDL, there is no need for cutting the cable or installing any driver, I am in EDL 9008 I don't need to "try to get there" as i'm already there.
These guides failed miserably as I have already tried them, my phone "doesn't receive a hello packet" from my phone, as I can't use adb or fastboot, or recovery.
I'll download linux and give that usb method a go then
m1shka said:
Okay so now a major reply!
I have stated in the OP that I am already in EDL, there is no need for cutting the cable or installing any driver, I am in EDL 9008 I don't need to "try to get there" as i'm already there.
These guides failed miserably as I have already tried them, my phone "doesn't receive a hello packet" from my phone, as I can't use adb or fastboot, or recovery.
I'll download linux and give that usb method a go then
Click to expand...
Click to collapse
Wish you luck:
Something that is never mentioned is to disable driver enforcement, this time hello packet was successfully recieved and flashed... Hold your happiness, cause now EDL no longer works so I can't see it in any com port and i'm certainly still in edl cause of the flashing led. Only difference I see is that now the led flashes when I hold the power button??? hmmmmmmm
To clarify:
Can't boot
Device was flashed successfully
Com port on pc can no longer see phone even after reboot
adb still don't work (proves again i'm in edl)
I'm in an even stickier situation now, can't access with my pc hmmmm..
m1shka said:
Something that is never mentioned is to disable driver enforcement, this time hello packet was successfully recieved and flashed... Hold your happiness, cause now EDL no longer works so I can't see it in any com port and i'm certainly still in edl cause of the flashing led. Only difference I see is that now the led flashes when I hold the power button??? hmmmmmmm
To clarify:
Can't boot
Device was flashed successfully
Com port on pc can no longer see phone even after reboot
adb still don't work (proves again i'm in edl)
I'm in an even stickier situation now, can't access with my pc hmmmm..
Click to expand...
Click to collapse
did you try to hold more than 30 second ? and also , do you have flash log ?
m1shka said:
Something that is never mentioned is to disable driver enforcement, this time hello packet was successfully recieved and flashed... Hold your happiness, cause now EDL no longer works so I can't see it in any com port and i'm certainly still in edl cause of the flashing led. Only difference I see is that now the led flashes when I hold the power button??? hmmmmmmm
To clarify:
Can't boot
Device was flashed successfully
Com port on pc can no longer see phone even after reboot
adb still don't work (proves again i'm in edl)
I'm in an even stickier situation now, can't access with my pc hmmmm..
Click to expand...
Click to collapse
So did you flash official stock ROM? Because I dont understand why doesnt it work... btw. when you flashed the ROM, did you lock bootloader?
Cant be battery dead?
If you are on "Qualcomm HS-USB QDLoader 9008" you will be able to flash stock fastboot firmware. Flash it using MiflashTool. Normally Miflashtool will recognized it as COMXX, where XX is the number of the port.
It's the official rom for the march ota.
The phone works, apparently it was encrypting everything... and now as I interrupted it, the encrypting failed and I lost all my data.....
Phone works but could have been better.
Before I reset the phone to factory, as i cannot use it yet, is there any way to get anything personal back? or is it gone gone and just factory reset?
What I see after boot, the phone resets every minute
https://drive.google.com/file/d/13sARZzlf3vJZK6Mx4hil6lsXRUl7-r-K/view?usp=sharing
The button that is hard to see says factory reset
m1shka said:
It's the official rom for the march ota.
The phone works, apparently it was encrypting everything... and now as I interrupted it, the encrypting failed and I lost all my data.....
Phone works but could have been better.
Before I reset the phone to factory, as i cannot use it yet, is there any way to get anything personal back? or is it gone gone and just factory reset?
What I see after boot, the phone resets every minute
https://drive.google.com/file/d/13sARZzlf3vJZK6Mx4hil6lsXRUl7-r-K/view?usp=sharing
The button that is hard to see says factory reset
Click to expand...
Click to collapse
Good job mate, so that SD card method worked with Linux? Be happy that your phone is alive.
EDIT: Maybe consider locking bootloader? Try it if youre on official stock.
EDIT 2: By flashing that ROM I guess you lost all data, but you can try to boot in TWRP without installing it and browse in file manager to see, if there is any data.
TrueMS said:
Good job mate, so that SD card method worked with Linux? Be happy that your phone is alive.
Click to expand...
Click to collapse
No... I was going to do that tomorrow but I decided to disable driver signature enforcement which worked. This should be written everywhere if it's this important..
Is there still a way to get my internal data back? Question as well, in recovery "mounting" the data partition will that let me get everything back "mounting" the drive to the pc? or do i not understand what mounting is.
m1shka said:
No... I was going to do that tomorrow but I decided to disable driver signature enforcement which worked. This should be written everywhere if it's this important..
Is there still a way to get my internal data back? Question as well, in recovery "mounting" the data partition will that let me get everything back "mounting" the drive to the pc? or do i not understand what mounting is.
Click to expand...
Click to collapse
As I said, you can try it, but when I flashed my Nougat stock ROM, i lost all the data. Or you can boot into TWRP and connect with USB to your computer to see the data in phone.
Good that your phone is working now, as for the data, i once forgot to remove encrypt before flash custom rom, but when enter TWRP it will ask for old password to decrypt. Just enter your old pass then connect to PC, or use TWRP file explorer to copy your data to sdcard
GVN.Gallus said:
Good that your phone is working now, as for the data, i once forgot to remove encrypt before flash custom rom, but when enter TWRP it will ask for old password to decrypt. Just enter your old pass then connect to PC, or use TWRP file explorer to copy your data to sdcard
Click to expand...
Click to collapse
None of the passwords I used worked.. I just factory reset it, thanks alot everybody. And now I will be more careful, don't flash anything weird. And backup!
I understood why I can't get the data back, if android fails at the encryption it jsut deletes everything!
My fone also in 9008 please can you guide me
I did the same what you have and it's on 9008 my flashing is successful but still my fone is not opening help me
m1shka said:
It's the official rom for the march ota.
The phone works, apparently it was encrypting everything... and now as I interrupted it, the encrypting failed and I lost all my data.....
Phone works but could have been better.
Before I reset the phone to factory, as i cannot use it yet, is there any way to get anything personal back? or is it gone gone and just factory reset?
What I see after boot, the phone resets every minute
https://drive.google.com/file/d/13sARZzlf3vJZK6Mx4hil6lsXRUl7-r-K/view?usp=sharing
The button that is hard to see says factory reset
Click to expand...
Click to collapse
How did you fixed i'm stuck in EDL?
SevenSlevin said:
If you are on "Qualcomm HS-USB QDLoader 9008" you will be able to flash stock fastboot firmware. Flash it using MiflashTool. Normally Miflashtool will recognized it as COMXX, where XX is the number of the port.
Click to expand...
Click to collapse
i am in Qualcomm HS-USB QDLoader 9008 but i can't flash, it doesn't matter if the phone is on fastboot mode or turned off (i can't even turn it on)
Good evening! I hope you can help me.
I flashed LineageOS 14.1, but I wanted to go back to EMUI. I made all the wipes and tried to flash different stock firmwares through a forced update (volume buttons + power button), but it never worked. At that point, I read about a guy in this forum who suggested to create a flashable zip with Huawei Update Extractor: I followed the suggestion and tried to flash it with TWRP. No error was given, but when I tried to restart, TWRP told me I had no OS installed. I thought it was strange, so I tried to restart anyway. That's when I got in rescue mode. I can't get into the recovery and I can't use fastboot. What rescue mode shows me is:
RESCUE MODE
Attention!
Please update system again
Update User Guide:
*link*
*android avatar*
Error!
Func NO: 10 (boot image)
Error NO: 2 (load failed!)
Pressing the three buttons, I'm able to force an update. The problem is I can't find a firmware that doesn't get rejected. With Lollipop firmwares, it starts to install, but it fails at 12%. With Marshmallow ones, the installation process doesn't even start.
What can I do to make it work again? I'm very sad because this phone was gifted to me a couple of days ago and I already messed it up. I don't even know how to turn it off.
What can I do to get in fastboot mode? At that point, what should I do to flash the stock firmware? Or maybe do I need to find the first stock firmware ever installed into this phone to make the forced update work?
Please, I need help. Thank you in advance!
P.S. The phone's model is ALE-L21. I live in Italy, so I assume it's a European version.
Did you managed to fix this?
Jhon_Locke said:
Did you managed to fix this?
Click to expand...
Click to collapse
Not yet, but I'm working on it. I found out that the device is recognized by my PC if I follow these steps:
1. Connect the phone to the PC and wait for it to go in rescue mode;
2. Wait until the notification LED stops to blink;
3. Disconnect the USB cable;
4. Press volume - and power button;
5. Reconnect the cable.
At that point, the screen turns black and the phone is recognized as "㌲㔴㜶㤸". I installed the drivers and now it's recognized as "HUAWEI USB COM 1.0". I should be able to reflash the partitions and make my phone work again, but I'm still trying to understand how to do it correctly.
Any help is appreciated!
ErikChimello said:
Not yet, but I'm working on it. I found out that the device is recognized by my PC if I follow these steps:
1. Connect the phone to the PC and wait for it to go in rescue mode;
2. Wait until the notification LED stops to blink;
3. Disconnect the USB cable;
4. Press volume - and power button;
5. Reconnect the cable.
At that point, the screen turns black and the phone is recognized as "㌲㔴㜶㤸". I installed the drivers and now it's recognized as "HUAWEI USB COM 1.0". I should be able to reflash the partitions and make my phone work again, but I'm still trying to understand how to do it correctly.
Any help is appreciated!
Click to expand...
Click to collapse
fastboot detects your device when you plug it into your computer?
I mean, if you run "fastboot devices" it shows your phone?
I've had this same problem but with an P8 Lite 2017, after flashing some ROM that supposedly was the stock one and trying to flash recovery I ended up with my phone bootlooping into rescue mode, I was able to "bypass" this thing rebooting my phone like crazy, seriously like after 20 reboot it finally booted into the damn ROM and I never touched the phone again. Sometimes when the phone ran out of battery and tried to power it on the phone booted into rescue mode and again after some reboots it booted to Android but now I want to install a custom ROM or at the very least root this damn phone so that's why I'm asking you if you have solved this, if you do then probably if I follow the same steps I would be able to fix that screen, hopefully.
If you are able to flash something start with flashing all recoveries your update.app has, maybe that's the problem (at least in my phone it is).
Jhon_Locke said:
fastboot detects your device when you plug it into your computer?
I mean, if you run "fastboot devices" it shows your phone?
I've had this same problem but with an P8 Lite 2017, after flashing some ROM that supposedly was the stock one and trying to flash recovery I ended up with my phone bootlooping into rescue mode, I was able to "bypass" this thing rebooting my phone like crazy, seriously like after 20 reboot it finally booted into the damn ROM and I never touched the phone again. Sometimes when the phone ran out of battery and tried to power it on the phone booted into rescue mode and again after some reboots it booted to Android but now I want to install a custom ROM or at the very least root this damn phone so that's why I'm asking you if you have solved this, if you do then probably if I follow the same steps I would be able to fix that screen, hopefully.
If you are able to flash something start with flashing all recoveries your update.app has, maybe that's the problem (at least in my phone it is).
Click to expand...
Click to collapse
No, it doesn't show anything if I write that command...
I guess mine won't ever boot into the rom because it seems like there's no system installed. I made some researches and found out there are some softwares that let you reflash the partitions IF the phone is recognized as "HUAWEI USB COM 1.0". I'm still trying to figure out how to do it correctly though. I feel like if I do something wrong, then my phone won't probably turn on again.
In your case, you should be able to flash a custom rom without any issue. You just have to be very careful and inform you as much as you can: I don't want your phone to end up like mine?. Anyway, it seems pretty hard to go back to the stock rom, so think about it before you flash a custom rom. Also, make a Nandroid Backup is very important.