Hello!!
I just got a DZ09, I need help identifying if it's fake or original, because I can not back it up, (flashtool).
The codes work, in a brief research on the internet, I found some very useful.
But I tried in win10,7, and today in xp, same symptom, when I click on "read back on flashtool, I connect DZ09 off, but after a few seconds, it turns on, and I got error (2005), something saying the device was turned on very fast ".
INFO:
version
NX9_61D_240_V2_1_ZH_DZ09D_ZX_IPS_32_T3_L3_C4_G4_B1_160507
[BRAHCH]:
11CW1352MP
GPLUS61A_11CNX9
BUILD: BUILD_NO
SERIAL#:
[BUILD TIME]
2016/05/07 15:25
[MRE VERSION] 3100
HAL_VERNO:
CHIP BB: MT6261
PLACA MS: HW2.1
Related
I am trying to figure out why my mobile phone (Galaxy Nexus) is not registering in foreign network(roaming). I think tracing RRC(Mobility Management) protocol messages would be a way to troubleshoot it and see at what point the registration procedure fails. Alternatively, some verbose diagnostic information could help to see whats going on in registration procedure.
For now I have decided to focus on RRC tracing.
What I have learned so far is that I can access Baseband Modem via serial device (in /dev) and interact with it via AT commands and possibly get traces or some diagnostics.
Q1: Am I on the right path?
I will appreciate any suggestions or link to relevant information.
I will update this thread as I progress.
HW:
Galaxy Nexus
Chipset: TI OMAP 4460
Baseband: Intel XG626
OS: CyanogenMod 11.0 (Android 4.4.4)
dear my friends ,urgent i need solution,have almost all programators like sigma kay ,hcu client dc phoenix ,octopus ..hcu client info
2018-12-25 02:38:06.103 Autodetect COM port and phone type start!
2018-12-25 02:38:07.212 Found COM port: COM83
2018-12-25 02:38:07.222 Found phone type: Huawei Android phone (Qualcomm CPU)
2018-12-25 02:38:07.234 Open COM port COM83 (DBAdapter Reserved Interface (COM83))...
2018-12-25 02:38:07.350 Start read phone info!
2018-12-25 02:38:07.478 Read phone secure info...
2018-12-25 02:38:07.739 Read phone basic info...
2018-12-25 02:38:07.849 Read phone info done!
Model: CAN-L11
IMEI: 8623****88888888
Firmware ver.: MSM8953C10B384_AMSS Nov 2 201810:28:29
Firmware model: CAN-L01
Dataver: CAN-L11C10B391_DATA_CAN-L11_hw_ru
SN: FPFD**********
PCB SN: DU4********
WiFi MAC: 182:76:8E:06:B1
BlueTooth MAC: 182:76:8D:F0:B0
Vendor: hw
Country: ru
RAM: 3GB
eMMC: 32GB
eMMC ID: 150100525831424D4206983DC6062400
HUN: 0000000000000000
IMEI 1 Sim Lock status:
NET: unlocked
NETSUB: unknown
SP: unknown
lets begin
customer brought can-l11 with android 6 ,in trying to flash it with nougat firmware ,it become dead ,only qualcom 9008 device recognized by pc ,so i flashed board firmware from dc support ,there is only Cannes-AL10_M001077_Board_Software_China_Nonspecific_Android_6.0_EMUI_4.1_firehorse
after that phone turns on but no imei,no serial ,no service nothing ,i have no backup ,
please i ask all members of this forum ,is any way to make phone fully in working condition ,please help me
i repaired imei .serial bluetooth wifi but signall of net is missing ,i think modem ,modemst1 and modemst2 partitions are missing ,please urgent i need your help,even 112 calling is impossible
Hi all
Recently i bought a new sw branded Y1 from china site
followed all tutorials over xda forum and internet
tried huge drivers to install on my pc (i was think the problem was my pc, so i gone to another and same issue)
put 2gb sd card , tried to change watch face, update firmware, but it even detect the watch
what i can do, please
Already tried these softwares
FundoRun
Mediatek smart device
Fundo Wear
in all these softwares, when i click on "Applications" the loading keeps on screen all time and dont shows the applications
[VERSION] K13-COB-Y1-9307CPT-QCY-MJW-V7.66-20181010
[BRANCH] 11CUMEOX61D_BT_11C
BUILD: BUILD_N
SERIAL#:
[BUILD TIME] 2018/10/1022:00
[MRE VERSION] 3100
HALVERNO:
solved, was the cable that come with the watch
Hello!
I am having trouble updating my MCU. I've been randomly losing this driver for a while now. After starting the car, the radio has a problem with starting (android works fine, no sound from the radio) when the MCU starts, the version is unknown. After 5 minutes, the device resets, sometimes the MCU will load and everything works until the car is turned off again.
During the update (SD Card FAT32, empty only with the original files from the joying blog - Trying few others), the information that SDCARD cannot be mounted
It goes to the line where the STM32UD was updated correctly, then the line with the description: "2019.09.07 10:40:57 JY_53_C63L_H32P48F64_Ver: 1.0" - the device is locked here, nothing happens - after 5 minutes, restart the device and loop.
How the device works properly MCU Version is:
2019.09.07 10:40:57 JY_53_C63L_H32P48F64_Ver: 1.0
Any factory reset not working.
CPU Info:
Intel X86_Octa-Coire 1.8Ghz [email protected] + 32 GB
Android 8.1
What should I do, what file should I use? Radio is:
Joying JY-UO135N4G
I don't speak perfect English, I use a translator. For thorough help, sending any files, I am able to use a grant. I am asking for help in solving the problem.
I am asking for information which data is still needed to solve the problem. The device is rotated.
After struggling to start the device, I did not have an MCU, I used Joying Extra Tool and the option -Rebot Option - Soft Reboot (Gui only, sufficient for all apk replacements)
After starting the car, the panel LEDs light up for 2 seconds and then they turn off, the device usually starts after a few minutes, the vehicle's logo is displayed with a countdown from 5 to 0, the device stops on the number 0. I have to hold power off and manually reset the device, then Andorid is charging correctly.
Twice after using it, the device started working properly. The MCU showed up in the settings.
System info:
Kernel: #451 SMP PREEMPT FRI MAR 29 2019
Platform: (24)6313 LF Full band carplay
touch: 911_1060(263efcda)E:0
APP 1024x600 2019-11-28 15:50:42
System 2019-11-28 09:40:06 Thursday
I have just installed a new headunit into my Kia. Everything works fine except wifi which I cannot manage to turn on. When I try turning it on it immediately turns off. Bluetooth works normally. I have tried restarting the unit, clearing cache, deleting wifi information.. everything to no avail. Does anyone know what I can do?
Thanks.
This is the exact headunit: https://www.amazon.de/dp/B08BK3XYFJ...t_i_ACPKTSHG3PB4ZVK86NEV?_encoding=UTF8&psc=1
About machine
Build number: 202106011022
Kernel version: 4.19.111
#231 Fri 05 28 11:32:21 CST 2021
uboot-05 11 2021-17:51:59_M11 1280X720
MCU version:
CSN2_04282021_173906_V102
CPU and Memory size:
64-Bit 8-Core Cortex-A53 1.5 GHz
4GB
Model and hardware:
Model: PX5
Android version:10
SIM STATUS: not availible
IP address: unavailible
Wi-Fi MAC address: unavailible
WorriedMushroom said:
I have just installed a new headunit into my Kia. Everything works fine except wifi which I cannot manage to turn on. When I try turning it on it immediately turns off. Bluetooth works normally. I have tried restarting the unit, clearing cache, deleting wifi information.. everything to no avail. Does anyone know what I can do?
Thanks.
This is the exact headunit: https://www.amazon.de/dp/B08BK3XYFJ...t_i_ACPKTSHG3PB4ZVK86NEV?_encoding=UTF8&psc=1
About machine
Build number: 202106011022
Kernel version: 4.19.111
#231 Fri 05 28 11:32:21 CST 2021
uboot-05 11 2021-17:51:59_M11 1280X720
MCU version:
CSN2_04282021_173906_V102
CPU and Memory size:
64-Bit 8-Core Cortex-A53 1.5 GHz
4GB
Model and hardware:
Model: PX5
Android version:10
SIM STATUS: not availible
IP address: unavailible
Wi-Fi MAC address: unavailible
Click to expand...
Click to collapse
Unfortunately, this is a common problem. If you recently bought the unit - return it. The issue is with faulty hardware.
Do you have the head unit's hotspot turned on? You can't run HOTSPOT and WIFI at the same time.