This is my first post here and though i read similar posts on this subject i would
like to read your opinions on this one.
I accidentally dropped some water on my touch hd and my display got damaged.The phone worked fine and so did the digitizer but the problem was that the backlight of the display was dead.At some point the backlight turned on but when i tried to input the unlock code it turned off right away (did this several times).I knew that i should replace the lcd (and the digitizer just in case).
I bought the lcd and the digitizer seperately and i managed to assemble the phone back using the service manual.Since then when i turn the phone on I hear the starting sound,i get the vibration then after a while the screen with no backlight again displays the "tap here to configure your phone" screen (after the hard reset),when i tap i get no response.
I checked the connections many times and i also used a second digitizer with no success.
Is there a possibility flashing a new ROM will solve the problem?
If so is there a way of flashing a ROM when the phone's screen is not usable?
Waiting for your precious opinions/suggestions/knowledge
Thanks in advance.
Hello,
Flashing the ROM won't solve an obviously hardware problem.
If you changed the LCD and still have no backlight, then either you bought a defective screen, or the problem is elsewhere, maybe on the main electronic board... Which would be bad news.
BTW, I wanted to change the digitizer in the apst years, but its not provided with the glue, so I had to buy a whole assembled screen + digitizer.
How did you manage to glue the digitizer on the screen ?
I aligned the screen with the digitizer and then i used small pieces of a special thin and trasparent tape to hold it in place.The tape holds the screen tight and it is barely visible, it also has the advantage that you can seperate the lcd and digitizer anytime you want with ease (though you have to be very delicate when applying it to get a good result)
I asked for a replacement of the defective lcd and i hope i will get a new one.
Hi guys,
What could be the possible reasons for a touchscreen and the capacitive buttons to stop working?
I purchased my Huawei U8800 only very recently but it was purchased 2nd hand. The phone came pre-installed with a custom rom, which is this one here: http://forum.xda-developers.com/showthread.php?t=1481168
I've had very minimal use of it ever since I received it, due to the reason that I have exams as I'm an UNI student. Therefore, I haven't modified the phone in any way, i.e I have not overclocked it or flashed a different kernel or recovery etc. The only thing I've done is installed GO SMS PRO and used it for txting and calling, that's it.
At first, everything seems to work fine. But on my 2nd day of use, the touchscreen started acting weird, where the right hand side of the screen stops working for no reason, as well as the 2 capacitive buttons on the right half of the screen (HOME and SEARCH). Then after a while, the BACK capacitive button on the left half of the screen stopped working, and eventually all 4 capacitive buttons and the entire screen stopped working.
The phone still turns on, but the entire screen doesn't pick up any finger input and there isn't any haptic feedback or vibration from the capacitive buttons. When I boot into the recovery, this is also the same.
So I contacted the seller about this, and he advised me to flash the Cyanogenmod 7.2 rom to see if this fixes the problem. It didn't, the touchscreen still doesn't work.
I'm wondering if this is related to the digitizer, which is the part of the phone that sense your finger inputs? If not, what are the other parts of the phone that could relate to the capacitive buttons and touch screen?
Definately a digitizer problem. The capacitive buttons are part of the touch screen, the touch screen is extended over the bottom of the display.
You should buy a new one from eBay or similar. If you want to buy it with a frame (black part on the front), you will have to open your phone to see if the front speaker is big or small. There are two types of front speakers and they are not cross-compatible. If you just want to buy the digitizer, you will have to remove the old digitizer from it's frame and add some glue on the new one to make sure it won't stick out.
If you don't want to mess with your phone, I am sure there are paid services that will do it for you, since replacing the digitizer is fairly easy.
Blefish said:
Definately a digitizer problem. The capacitive buttons are part of the touch screen, the touch screen is extended over the bottom of the display.
You should buy a new one from eBay or similar. If you want to buy it with a frame (black part on the front), you will have to open your phone to see if the front speaker is big or small. There are two types of front speakers and they are not cross-compatible. If you just want to buy the digitizer, you will have to remove the old digitizer from it's frame and add some glue on the new one to make sure it won't stick out.
If you don't want to mess with your phone, I am sure there are paid services that will do it for you, since replacing the digitizer is fairly easy.
Click to expand...
Click to collapse
thanks for your reply mate!
Ok so I've found this one here:
http://www.ebay.com/itm/Original-To...Glass-For-Huawei-U8800-Ideos-X5-/170721993712
Since it says it's "original", I don't have to worry about the speaker problem right?
chaoscreater said:
thanks for your reply mate!
Ok so I've found this one here:
http://www.ebay.com/itm/Original-To...Glass-For-Huawei-U8800-Ideos-X5-/170721993712
Since it says it's "original", I don't have to worry about the speaker problem right?
Click to expand...
Click to collapse
They are selling the digitizer, so there will be no problems as it's only the digitizer glass and not the frame around it. The frame itself is holding the digitizer and the speaker so that's why there may be issues when buying the front cover.
If you need a disassembly tutorial, check my Mediafire (signature) -> Documents -> U8800 Basic Maintenance Manual. It's the official disassembly guide so you can be sure you are doing it right .
Blefish said:
They are selling the digitizer, so there will be no problems as it's only the digitizer glass and not the frame around it. The frame itself is holding the digitizer and the speaker so that's why there may be issues when buying the front cover.
If you need a disassembly tutorial, check my Mediafire (signature) -> Documents -> U8800 Basic Maintenance Manual. It's the official disassembly guide so you can be sure you are doing it right .
Click to expand...
Click to collapse
Wait, that doesn't have the frame around it? I thought the black part surrounding the glass is the frame? I'm confused.......
I just want something that looks exactly like shown in that Ebay listing photo, where it has that bit of the connector part that you push into the motherboard (or whatever it's called on the phone).
chaoscreater said:
Wait, that doesn't have the frame around it? I thought the black part surrounding the glass is the frame? I'm confused.......
I just want something that looks exactly like shown in that Ebay listing photo, where it has that bit of the connector part that you push into the motherboard (or whatever it's called on the phone).
Click to expand...
Click to collapse
On your listing, it does not have frame.
If it's without frame, it is simply the front glass with connector. If it is with the frame, it has the black curve too (and speaker with led).
See this:
Without frame.
With frame.
Hope it makes sense now
Blefish said:
On your listing, it does not have frame.
If it's without frame, it is simply the front glass with connector. If it is with the frame, it has the black curve too (and speaker with led).
See this:
Without frame.
With frame.
Hope it makes sense now
Click to expand...
Click to collapse
Ahh ic ic.....so would I need to use glue to stick the digitizer glass onto the frame?
chaoscreater said:
Ahh ic ic.....so would I need to use glue to stick the digitizer glass onto the frame?
Click to expand...
Click to collapse
Yeah, but not much. Maybe you don't need to add any glue at all, the old one might hold it too.
u8800-51 touch screen bottom not responding
Blefish said:
On your listing, it does not have frame.
If it's without frame, it is simply the front glass with connector. If it is with the frame, it has the black curve too (and speaker with led).
See this:
Without frame.
With frame.
Hope it makes sense now
Click to expand...
Click to collapse
hi blefish
just posted a similar question:
http://forum.xda-developers.com/showthread.php?p=39201328#post39201328
is it the same solution? (the 4 buttons at the bottom do not work as well as the lower half of screen)
my speaker is 15 mm by 5 mm long (i looked inside). is it big or small?
all the ebay posts do not mention a frame - i will be happy not to mess with the glue
thanks
huwaei G 510
Hi guys,
I did have the same problem with a Huawei G 510. Digitizer broken and replaced, but still not working.
I have no action on screen. It lits but i can't press any button. Either the 3 buttons are working.
Checked the plug, checked some voltage in the pins.
Any other ideas ?
Thanks in advance,
Miltos Matt
Hi
I've dropped my HD2. Everything is working, including touch screen, I can unlock the phone, I can answer the call, but screen is black, not broken.
What should I do? Does the lcd screen replacement will be sufficient? In that case, could the screen be ok, but some other display "processor" could be dead? I'm asking because I'll try to this on my own.
Could simply be the lcd cable has slipped slightly but probably more likely an LCD replacement needed.
You need remove rear housing & have a look & make a decision from your findings/testing.
hello
I've got a little update - lcd screen is working well - I mean it displays the image, the only malfunction is backlit. Right now when i use flashlign I can actually see whats on screen. Do you have experience or think that backlit connection can be repaired? Do You have any schematics for hd2' lcd ?
I suspect new LCD required by sounds of it. LCD can not be stripped for repair so after basic inspection of external connection replacement is only solution & not expensive due to falling cost of HD2 parts.
My HTC HD2 with kitkat os falling from my hand and after that the screen shows nothing, my phone is alive and everything works like ringing vibrate alarm even touch screen and touch vibrate, but i see nothing and the display is dark.
whats my problem? can i fix it?
thanks for reply me
any body ????
muhama said:
My HTC HD2 with kitkat os falling from my hand and after that the screen shows nothing, my phone is alive and everything works like ringing vibrate alarm even touch screen and touch vibrate, but i see nothing and the display is dark.
whats my problem? can i fix it?
thanks for reply me
Click to expand...
Click to collapse
any body ????
probably need new screen assembly!
needs opening to check lcd connector to mainboard & if all connections good then new screen should be tried.
LCD & digitizer pre built assembly is only about $30 these days for decent ones but indeed not easy fit with some experience or good read up on procedure & good care when doing it.
Mister B said:
probably need new screen assembly!
needs opening to check lcd connector to mainboard & if all connections good then new screen should be tried.
LCD & digitizer pre built assembly is only about $30 these days for decent ones but indeed not easy fit with some experience or good read up on procedure & good care when doing it.
Click to expand...
Click to collapse
Thanks for reply me:good:
How can i open my phone? And where is connector located?
Do you have a link to view that?
Have a read of this thread for start
http://forum.xda-developers.com/showthread.php?t=1566179
Plenty more if do a search
Basically be very very careful, use plastic pry tool ONLY to remove back, start at top. 2 clips about 7mm in from top edges then once released work down right side, DO NOT stick any tools in near the volume key, if doing it right the back comes of very easy (2 pry tools are better as can keep one in top sstopping it clipping back in)
Once back off handle with care, rough handling breaks th spring contacts for antenna etc.
LCD from mainboad can be disconnected from mainboard without fully removing flex & is absolute best way do it.
I did write few posts on it so will try dig them up & link you.
If buy lcd/gigi assemble also buy a button board ribbon as they like only $3USD, with spare button ribbon you can easily plug new lcd/digi in & plug new button board ribbon into mainboard & hold a battery on it to do a test befoe sticking things together.
Also you likely damage ribbon if not careful so spare likely get used on rebuild.
Parts link is in HD2 Wiki
http://forum.xda-developers.com/wiki/HTC_HD2#Fixes.2C_Hints_.26_Tips
I recently purchased a ZTE Max Pro (Used), it had a broken screen and LCD, so I replaced the glass, replace the digitizer, LCD and now when I plug it in all it does is vibrate and the home button, little circle at the bottom, they just come on. I seen one another site that they said I might need a new battery, so I'm just throwing this out here to you guys cuz you're lot smarter than I am about these things, but what your take is on this. Any and all help will be greatly appreciated.