I cracked my aria screen pretty much right after I got it, Managed to get my hands on a new digitizer and replaced it. I found a quick walkthrough on Android forums. It helped but had a few points that could have been more succinct.
Posting here in case anyone needs.
Took me about an 1hr 30min the first time trying to figure it out on my own.
My additional comments are indicated by **.
I put some addendums to @Jcawesome's steps...
( http://androidforums.com/1211507-post42.html )
1. Remove backcover
2. Remove Battery, sim chip, and memory card
3. Unscrew the top two screws (meaning the end farthest from the memory card.)
4. Using a flat plastic wedge, (I used the one that came from my ebay order, it looks like the blue tool in this pic )
5. Carefully pull off the parts at the top being very cautious not to break anything. (Do not pull the circuit board out, only lift the end closest to the edge of the phone)
** there are two pieces to pull off....with the phone laying flat (screen down and the top facing away from you) a larger yellow piece with an attached back speaker comes out towards you. a second piece pulls up (north as if on a map)... but becareful because there is a bunch of tape and tackiness all throughout this thing (literally I felt it was held together by tape). I actually pulled off the grill on front as well.
** the circuit board is kept attached near the top right. the element that is the power button snaps off. (there are two little dots just to the right of the speaker with what looks like blackish tape that connects to the circuit board... you can pop this off.
With that off, I could lift the circuit board about 30 degrees or so... I wasn't comfortable pulling it back any farther than that.
I did step 5 AFTER I got the screen off.
6. Using the flat plastic wedge again, push the wedge tool between the phone and the broken screen. (It will feel like you are breaking it but it is fine, it is held on by a sticky paste that will slowly give way)
** careful on this part... especially difficult depending on how your screen is cracked. but it is just a bunch of sticky tape that is keeping it attached.... I had to peel away the goo and connection near the top sensitive areas as my ear piece speaker came off with the goo.
7. Disconnect the connecter from the old digitizer to the new one and remove the old digitizer.
**I used a small little tweezer and sneaked it in underneath the circuit board to pull the digitizer connection out.... a little difficult to push back in, but just took some patience.
8. Being careful not to put fingerprints on any exposed surface of either the phone lcd or the replace screen, place the new digitizer in the exact spot of the old one.
** have some lint free microfiber cloth handy and perhaps some screen cleaner.... I spent about 15 minutes cleaning the lcd screen before laying the replacement digitizer back on.
I actually did step 9 before step 8.
9. Connect the connecter from the new digitizer to the board, be careful not to pull the circuit board out and do not scratch the board.
10. You may want to use some glue to hold the new screen on, hopefully this will not happen again. My phone still had enough of the sticky paste left to hold the new screen fine.
** I agree... the first time you replace it will be fine.... afterwards tho, I can see it running out of tackiness.....
11. Put the phone back together in reverse order.
12. Turn it one and everything should be working again.
** in a nut shell
1) take out two screws
2) detach two yellow shell pieces
3) unhook a latch that is the power button
4) pry off the screen
5) lift the circuit board approx 30 degrees.
6) detach digitizer connection from underneath using tweezer
7) replace digitizer connection, return circuit board flat
8)position digitizer and press down to adhere
9)replace two plastic yellow shell pieces
10) screw it back together
done.
let me know if you have any questions.=)
enjoy your "brand" new aria.
dude,, this is a PITA,, I did,, was about 1hour, the hardest part,, is to not put the fingers on the LCD and cleaning the new screen..... dust particles everywhere... and at the end still got one...
Sorry eortizr, If I made it seem easier than it was. I spent quite a while cleaning the lcd screen when I replaced the digitizer... I don't think it's possible to change the digitizer without getting fingerprints on it though. But with some diligence and working in a clean area, I was able to keep all dust and finger prints out of the final product.
My wife dropped hers. Cracked up pretty good but still functional. Think I might just go ahead and pay the $100 and have someone who does it for a living do it.
I can totally see me trying DIY concentrating real hard dripping sweat all over it and ruining the MB. LOL
Replaced the screen today. Half way in I thought I definitely bit off more than I could chew. I got it done though. A couple of things I learned:
The digitizer unplugs away from you or toward the screen with the phone laying flat (screen down and the top facing away from you). I kept thinking i had to unplug it by pulling it north, toward the top of the phone.
I dropped and threw away both the front speaker and the very small rubber piece that covers the proximity sensor so... when I turned the phone on everything looked good, until I answered my phone. The screen went blank and I couldn't hear anything. I found the speaker and the proximity sensor cover and replaced them.
I would do it again, its worth saving $50 or so.
Thanks for the tutorial dreamflux.
I found the whole kit including the adhesive here: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=180643624141
This is the seller in case the sale ends and the link breaks: http://myworld.ebay.com/chinaphoneaccessories/?_trksid=p4340.l2559
I found a replacement digitizer from tmart dot com for $55, free shipping. Just search Aria on their site, you'll find it. Sorry, I can't seem to post links yet.
What was peculiar, was that it has only the HTC logo in the center, and no ATT logo. Looks nice and clean. They included plastic separator tools and torx drivers, though nothing in this phone uses torx. The site is a little shady, and while their headquartered in Hong Kong, it shipped from Brooklyn NY about 5 days after purchase, priority mail. The swap wasn't bad, but my only complaint is that the lights from the softkeys seem to shine up onto the screen, but you get used to it. It's probably because I didn't transfer the stickers over on the bottom of the digitizer.
Thanks for the directions ... I just replaced my digitizer. I had 2 major problems: 1) my power button doesn't work any longer (I'm going to take it apart and try to put it back together and see if that fixes it), and 2) you HAVE to use BLACK sticky stuff to seat the bottom of the digitizer - I used the clear stuff that came with the digitizer, and now I have tons of light bleeding into the LCD from the button backlights. I'm not sure what to do about the bleed ... I guess I'll have to tear it down again and put black stuff in ... damn.
That's the deal with that excess backlighting! I thought it was just a matter of the screen being misaligned. Terrible that I have to replace that black foam, it got shredded while I was dismantling the thing to replace the digitizer.
eortizr said:
dude,, this is a PITA,, I did,, was about 1hour, the hardest part,, is to not put the fingers on the LCD and cleaning the new screen..... dust particles everywhere... and at the end still got one...
Click to expand...
Click to collapse
its always suggested to work in a dust-free space but we all know that's virtually impossible.
I had a bit of fun with dust & fingerprints when replacing my LCD after getting my Aria, After a time or two of taking apart and being unsuccessful, I left it as is with one visible flake.
If you take a hot shower the steam in the air sticks to dust particles leaving no dust
Sent from my Liberty using XDA App
aria
use electrical tape to cover up the lighting that comes through the digitizer
use 3m double sided tape to hold digitizer to lcd
use rubber gloves to change screen to not get finger prints on it
dust906 said:
use electrical tape to cover up the lighting that comes through the digitizer
use 3m double sided tape to hold digitizer to lcd
use rubber gloves to change screen to not get finger prints on it
Click to expand...
Click to collapse
*Just to make sure I'm putting the electrical tape on correctly*
put the double sided tape on and then put the electrical tap (sticky side facing up) on top of the ds tape then apply the screen to the lcd
Thanks for the explanation dreamflux.. This, along with some youtube videos helped me out to change the digitizer, but patience is THE key...
Brought my phone with me to Cedar Point the other day. Survived the entire day....until I stopped at the bars on the way home. Got out of the car, forgetting I had my phone on my lap---shattered right by the track pad.
Just got my digitizer today for $22 on ebay (not bad) After 2 hours and a migraine later, everything came out great.
The only 2 things wrong now are the light from the softkeys bleeding onto the screen and out the sides (I'm just going to shut those lights off), and the trackpad sits a little lower than the screen now. Either I didn't align it right, or the glue isn't holding well. It's weird, if you press on the glass anound the trackpad, it wakes the phone (cm7 trackpad wake).
I only plan on using the phone for a few more months, so I'm happy with the results.
Uhhggg, did the replacement on my son's Aria. It wasn't so bad, but now the LCD screen doesn't light.
I get the vibration when you first hit the power button. Is this correct? I'm not too familiar with the phone.
Rececked the connector for the LCD and it seems to be snapped in.
brivette007 said:
Brought my phone with me to Cedar Point the other day. Survived the entire day....until I stopped at the bars on the way home. Got out of the car, forgetting I had my phone on my lap---shattered right by the track pad.
Just got my digitizer today for $22 on ebay (not bad) After 2 hours and a migraine later, everything came out great.
The only 2 things wrong now are the light from the softkeys bleeding onto the screen and out the sides (I'm just going to shut those lights off), and the trackpad sits a little lower than the screen now. Either I didn't align it right, or the glue isn't holding well. It's weird, if you press on the glass anound the trackpad, it wakes the phone (cm7 trackpad wake).
I only plan on using the phone for a few more months, so I'm happy with the results.
Click to expand...
Click to collapse
did you have any problems with the digitizer responsivenes or something like that? I'm need one and curious about the quality of the cheap digitizers in ebay.
so I replaced my friends screen and now the phone turns on, has sound, vibrates, but just doesnt turn the screen on... the light sensor works and all, and if I call it, it rings and everything, just the screen won't turn on it stays black... I've checked the 2 ribbons and everything is fine, anyone have a suggestion..??
jdmsohc22 said:
so I replaced my friends screen and now the phone turns on, has sound, vibrates, but just doesnt turn the screen on... the light sensor works and all, and if I call it, it rings and everything, just the screen won't turn on it stays black... I've checked the 2 ribbons and everything is fine, anyone have a suggestion..??
Click to expand...
Click to collapse
so what I meant was the digitizer turns on, but it is just a dark lit screen, no visual anything going on.. If i call it from another phone it will ring, but when i swipe right to left to answer and press around where the answer button is it doesn't respond either, just rings and rings... anyways just wanted to elaborate a little more..
---------- Post added at 02:28 AM ---------- Previous post was at 02:08 AM ----------
msailer said:
Uhhggg, did the replacement on my son's Aria. It wasn't so bad, but now the LCD screen doesn't light.
I get the vibration when you first hit the power button. Is this correct? I'm not too familiar with the phone.
Rececked the connector for the LCD and it seems to be snapped in.
Click to expand...
Click to collapse
same thing is happening with me as well..
^^^^ Soooooo.....I got the same thing on my wife phone, the BLACK SCREEN. I did my homework and read and watched videos on how to replace the digitizer. I was in a steamy room with all my tools from work with pre-cut electrical and .005" double sticky tape. im a mechanical assembler. I did everything to the tee and was very carefull. i think i got a bunk one from china. I bought mine for $19 from china. It had at&t logo and everything. you get what you pay for? So I've got to pay now $50 for a replacement phone through ins. Not bad because before i made the claim i thought the replacement was $150. Anyways just a heads up. Now i got a phone of spare parts Whats cool is that i get to root her phone all over again. So if anyone here has had the black screen. let me know what happened next with your situation. Did you fix it? replaced it with another one? thanks
This is my first post here and though i read similar posts on this subject i would
like to read your opinions on this one.
I accidentally dropped some water on my touch hd and my display got damaged.The phone worked fine and so did the digitizer but the problem was that the backlight of the display was dead.At some point the backlight turned on but when i tried to input the unlock code it turned off right away (did this several times).I knew that i should replace the lcd (and the digitizer just in case).
I bought the lcd and the digitizer seperately and i managed to assemble the phone back using the service manual.Since then when i turn the phone on I hear the starting sound,i get the vibration then after a while the screen with no backlight again displays the "tap here to configure your phone" screen (after the hard reset),when i tap i get no response.
I checked the connections many times and i also used a second digitizer with no success.
Is there a possibility flashing a new ROM will solve the problem?
If so is there a way of flashing a ROM when the phone's screen is not usable?
Waiting for your precious opinions/suggestions/knowledge
Thanks in advance.
Hello,
Flashing the ROM won't solve an obviously hardware problem.
If you changed the LCD and still have no backlight, then either you bought a defective screen, or the problem is elsewhere, maybe on the main electronic board... Which would be bad news.
BTW, I wanted to change the digitizer in the apst years, but its not provided with the glue, so I had to buy a whole assembled screen + digitizer.
How did you manage to glue the digitizer on the screen ?
I aligned the screen with the digitizer and then i used small pieces of a special thin and trasparent tape to hold it in place.The tape holds the screen tight and it is barely visible, it also has the advantage that you can seperate the lcd and digitizer anytime you want with ease (though you have to be very delicate when applying it to get a good result)
I asked for a replacement of the defective lcd and i hope i will get a new one.
Hello, I change the screen to my Z and I have this problem.
I noticed the screen flicker when you touch or press the edges of the screen / phone. It's like if you increase the intensity of light.
The display properly reacts to the pressure of the fingers, sliding screen keyboard ...
What can happen? The screen? I open it?
The 2 Connectors of the screen with the board?
Thanks
are you using auto light? if yes try to disable it
I'm guessing it's an issue with the connections. Are you using too much pressure on the screen? I've never seen that happen on mine.
PazzoPazzini said:
are you using auto light? if yes try to disable it
Click to expand...
Click to collapse
Nooo
shadowx360 said:
I'm guessing it's an issue with the connections. Are you using too much pressure on the screen? I've never seen that happen on mine.
Click to expand...
Click to collapse
I think this is, I will dismantle it and see what happens.
Repair fail !!
Well I'm back to open the Z and I've broken the screen.
I get those lines and a black spot. 25 euros lost.
I hope it's only the screen and the digitizer.
this happened to me now i cant get anything but the lowest brightness
if you have the same as me its not the screen i think its the cable but i cant find a cheap replacement to test it plus i am thinking of going to the droid 4 if/when it gets its gsm update
Did you manage to fix the problem with your Desire Z screen, I had exactly the same problem after replacing the LCD. I took it apart and put it back together again & again but couldn't find what was causing it.
I think when you take the screen out the first time, you remove that clear glue stuff, and probably make it slightly loose. So what I did was take some of them sticky labels for printing. With a scalpel cut some very thin strips (about 2mm in width and almost the full length of each side), folded them into an L shape and stuck them aroud the 3 edges of the LCD, before sinking it into the housing and the problem is fixed.
Just in case I've not explained that very well, here is a really bad diagram.
...John...
http://forum.xda-developers.com/showpost.php?p=28506002&postcount=7
Repared
Merci all
Hi guys,
I just disassembled my HD2 to replace my broken digitizer and touchscreen.
But now i'm stuck with a problem.
What shall I use to glue both items together again?
And the keyboard makes some issues.
I tried to place both parts over eachother to see if they fit but I can't press the keys after it.
Seems like they are stuck.
That's why I didn't want to use superglue because after assembling it I wouldn't be able to change anything.
Maybe pictures tell more than words.
http://www.youtube.com/watch?v=t8Q7mXdcJ54&feature=player_embedded
hope that helps you
thanks wasn't the information I was looking for but nevermind
I assembled the device now .. but the next problem occured ..
the hd2 is loading without problems (led shows it) but when I try to power it on it's completely dead. nothing happends
with my old touchscreen it was at least possible to power it on.
my question is:
could the new soldered touchscreen + digitizer be broken? or did I break something during disassembly and assembly?
To be honest I didn't see any mistakes I made.
It's not my first time repairing stuff like that because I used to repair notebooks as a hobby.
Still i'm unsure what the heck is going on with my phone atm.
did you check if the flex cable from display is in the port, there is an white stripe that shows how far it must in the port. Did the phone vibrate when you pressed power button?
I checked the cables and found nothing suspicious.
and the phone didnt even vibrate after trying to power it on.
I'm trying to get a new hardkey board (i hope you know what I mean).
Had problems with the keys being stuck and maybe I killed that one by trying to assemble it.
if the phone doesn't recognize me pushing the power on key it's no wonder it won't do anything.
hope this will fix the problem
12dollar said:
I checked the cables and found nothing suspicious.
and the phone didnt even vibrate after trying to power it on.
I'm trying to get a new hardkey board (i hope you know what I mean).
Had problems with the keys being stuck and maybe I killed that one by trying to assemble it.
if the phone doesn't recognize me pushing the power on key it's no wonder it won't do anything.
hope this will fix the problem
Click to expand...
Click to collapse
Most likely something is wrong with your Power button, but you should turn it on with 2nd method:
- pull out battery;
- insert usb cable(connected to PC)/charger in your usb port;
- insert battery.
This way it should turn on whatever OS you have installed on.
If your OS is Android through MAGLDR, connecting it through usb should turn it on by default, unless your battery is not dead!
Check it out!
bib*oops said:
Most likely something is wrong with your Power button, but you should turn it on with 2nd method:
- pull out battery;
- insert usb cable(connected to PC)/charger in your usb port;
- insert battery.
This way it should turn on whatever OS you have installed on.
If your OS is Android through MAGLDR, connecting it through usb should turn it on by default, unless your battery is not dead!
Check it out!
Click to expand...
Click to collapse
I just did as you said and yeah the phone came to life.
so there is definately a dead power button (probably the board is broken)
12dollar said:
I just did as you said and yeah the phone came to life.
so there is definately a dead power button (probably the board is broken)
Click to expand...
Click to collapse
Glad to hear that!
Definitely you should replace your keypad flex!
Did you fix the problem with the hardware keys
Hi,
I have very similar problem.
I changed the touch screen on my HD2 and after reassembling I cannot get the hardware keys clicked.
I ordered a brand new key board and brand new plastic buttons. I received them but situation is the same.
If somebody can explain is there any trick during adjusting the plastic buttons to the clickable "small dots" on the board - please help me.
Best Regards
maznevh said:
Hi,
I have very similar problem.
I changed the touch screen on my HD2 and after reassembling I cannot get the hardware keys clicked.
I ordered a brand new key board and brand new plastic buttons. I received them but situation is the same.
If somebody can explain is there any trick during adjusting the plastic buttons to the clickable "small dots" on the board - please help me.
Best Regards
Click to expand...
Click to collapse
Normally this is always down to glass digitizer not being aligned correctly when stuck to LCD.
0.05mm can make all the difference here.
You need review current digitizer position & pre test assembly to centre chassis without tape for a test run on button function.
Also check button board position is exact & located correctly in the pin holes at each end of the board.
original board quality is normally far better than most of the very cheap eBay pattern parts but one or two sellers offer a decent board around $4.50
Also clean all old tape from back of LCD & centre chassis plate so parts fit flush & once all checked new tape can be added, I also use small spots of up40 adhesive sealant near corners & near middle edges for final build up as holds far better than even the best tapes & gives an original strength & long lasting flush look to final job plus us easily removed with razor blade if repair ever needed again.
Super glue is a BIG no no NO.
Hard to get hardware buttons clickable
Mister B said:
Normally this is always down to glass digitizer not being aligned correctly when stuck to LCD.
0.05mm can make all the difference here.
You need review current digitizer position & pre test assembly to centre chassis without tape for a test run on button function.
Also check button board position is exact & located correctly in the pin holes at each end of the board.
original board quality is normally far better than most of the very cheap eBay pattern parts but one or two sellers offer a decent board around $4.50
Also clean all old tape from back of LCD & centre chassis plate so parts fit flush & once all checked new tape can be added, I also use small spots of up40 adhesive sealant near corners & near middle edges for final build up as holds far better than even the best tapes & gives an original strength & long lasting flush look to final job plus us easily removed with razor blade if repair ever needed again.
Super glue is a BIG no no NO.
Click to expand...
Click to collapse
It is not the case in my case , because I ordered full set (digitizer + display) and they arrived factory assembled.
But you are definitely right - 0.05 mm make the difference. I think the problem comes from the fact that the board with buttons cannot be firmly fixed to the 2 small juts on the chassis. You know the plug of the buttons board is on the tail like extension. Probably when I try to cover the buttons board with the LCD+digitizer - the frame of the LCD slightly pushes the buttons board and the juts on the plastic buttons cannot be fixed exactly on the top of the actual buttons on the board. Anyway we are speaking about precise fixing something around 0.05 mm over something else, which is exactly same size... and in the same time you have to fix this without any visibility.
I will continue trying. If you can give me any other ideas - I will appreciate this.
Thanks
maznevh said:
It is not the case in my case , because I ordered full set (digitizer + display) and they arrived factory assembled.
But you are definitely right - 0.05 mm make the difference. I think the problem comes from the fact that the board with buttons cannot be firmly fixed to the 2 small juts on the chassis. You know the plug of the buttons board is on the tail like extension. Probably when I try to cover the buttons board with the LCD+digitizer - the frame of the LCD slightly pushes the buttons board and the juts on the plastic buttons cannot be fixed exactly on the top of the actual buttons on the board. Anyway we are speaking about precise fixing something around 0.05 mm over something else, which is exactly same size... and in the same time you have to fix this without any visibility.
I will continue trying. If you can give me any other ideas - I will appreciate this.
Thanks
Click to expand...
Click to collapse
Do not rule out the LCD/Digitizer assembly as the china combos are prone to not the best accuracy of assembly as sounds like maybe LCD is mounted just a fraction too low on the digitizer perhaps.
Button board should be fixed via 3M style tape & most replacement boards come with tape ready for fitting.
worth making effort with button board to centre chassis to mount securely then mounting lcd to chassis without tape for a trial assembly & try and check for possible issues such as bent chassis or old tape not removed sufficiently or new assembly alignment not the best.
I would also recommend using original plastic button strip as the copy ones are not always good & have had experience with them before.
My HTC HD2 with kitkat os falling from my hand and after that the screen shows nothing, my phone is alive and everything works like ringing vibrate alarm even touch screen and touch vibrate, but i see nothing and the display is dark.
whats my problem? can i fix it?
thanks for reply me
any body ????
muhama said:
My HTC HD2 with kitkat os falling from my hand and after that the screen shows nothing, my phone is alive and everything works like ringing vibrate alarm even touch screen and touch vibrate, but i see nothing and the display is dark.
whats my problem? can i fix it?
thanks for reply me
Click to expand...
Click to collapse
any body ????
probably need new screen assembly!
needs opening to check lcd connector to mainboard & if all connections good then new screen should be tried.
LCD & digitizer pre built assembly is only about $30 these days for decent ones but indeed not easy fit with some experience or good read up on procedure & good care when doing it.
Mister B said:
probably need new screen assembly!
needs opening to check lcd connector to mainboard & if all connections good then new screen should be tried.
LCD & digitizer pre built assembly is only about $30 these days for decent ones but indeed not easy fit with some experience or good read up on procedure & good care when doing it.
Click to expand...
Click to collapse
Thanks for reply me:good:
How can i open my phone? And where is connector located?
Do you have a link to view that?
Have a read of this thread for start
http://forum.xda-developers.com/showthread.php?t=1566179
Plenty more if do a search
Basically be very very careful, use plastic pry tool ONLY to remove back, start at top. 2 clips about 7mm in from top edges then once released work down right side, DO NOT stick any tools in near the volume key, if doing it right the back comes of very easy (2 pry tools are better as can keep one in top sstopping it clipping back in)
Once back off handle with care, rough handling breaks th spring contacts for antenna etc.
LCD from mainboad can be disconnected from mainboard without fully removing flex & is absolute best way do it.
I did write few posts on it so will try dig them up & link you.
If buy lcd/gigi assemble also buy a button board ribbon as they like only $3USD, with spare button ribbon you can easily plug new lcd/digi in & plug new button board ribbon into mainboard & hold a battery on it to do a test befoe sticking things together.
Also you likely damage ribbon if not careful so spare likely get used on rebuild.
Parts link is in HD2 Wiki
http://forum.xda-developers.com/wiki/HTC_HD2#Fixes.2C_Hints_.26_Tips