hi all, please help me my note 3 sm n900 stuck at note 3 logo, only download mode works, recovery mode not working. when i try to flash stock rom via odin its showing following log
leaves cs..
odin v.3 engine
file analysis
setup connection
initializing....
the its taking ages not going further:crying:
please help
it went into this state automatically i have not done anything, suddenly it was powered off then this problem occurred, btw its charging & showing battery % as well....
What are you flashing ??
JJEgan said:
What are you flashing ??
Click to expand...
Click to collapse
i was flashing nothing suddenly my fone get switched off then i tried to switched on so its not booting, odin is recognizing fone but fail to flash anything its giving error in the end something like " (pass 0/ failed 1)
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1101)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
Try different USB cables and USB ports.
nickomy said:
<ID:0/003> Initialzation..
Click to expand...
Click to collapse
Alots reason if stuck like this and some solution is weird but works
Wrong firmware, download the right one.
Not pull out battery and reinsert before flash with odin(better takeout sim and SD card, yeah this weird)
Cable problem
PC port problem(changing to others port)
Using wrong version, odin(better using latest)
Odin problem/bug in PC(because old version alots problem, solution is to close odin and open again then flash ROM
Another way, just flash TWRP, backup important file using TWRP then flash custom ROM
Try it & Goodluck.
audit13 said:
Try different USB cables and USB ports.
Click to expand...
Click to collapse
Tried with different usb cables & different usb ports but still no luck, read somewhere on xda that. The problem is with your device's hard drive which you may define as system storage . This is a very common issue with Samsung devices . Don't worry it's easy to fix . If you have warranty then go to Service center and if you don't have warranty then go to a service professional and ask him to replace your device's hard drive which contains ram and emcc in a single chip. If you face no base band issue then simply flash efs via odin that will resolve the imei issue
download menu status is
ODIN MODE
Product Name : SM-N900
Current Binary: Samsung Official
System Status: Official
Reactivation Lock (KK): OFF
Secure Download : Enabled
KNOX WARRENTY VOID : 1
RP SWREV : A4
Odin readings are
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N900XXUEBOC4_N900ODDEBOB2_N900DDUEBOB1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
Does a com port get assigned to the phone in Odin?
audit13 said:
Does a com port get assigned to the phone in Odin?
Click to expand...
Click to collapse
some times yes some times no, then I'd to take out the battery n reinsert to recognize by odin. Kies is not recognizing at all. Thanks for your prompt replies really appreciate it:fingers-crossed:
It's definitely a problem if the phone losses USB connectivity.
It's possible the usb port on the phone is defective?
audit13 said:
It's definitely a problem if the phone losses USB connectivity.
It's possible the usb port on the phone is defective?
Click to expand...
Click to collapse
but its charging both from wall socket n laptop as well
There are 4 wires in a usb cable: 2 for data, 2 for power.
It's possible for a phone to charge and not transfer data.
audit13 said:
There are 4 wires in a usb cable: 2 for data, 2 for power.
It's possible for a phone to charge and not transfer data.
Click to expand...
Click to collapse
Ok i'll recheck n confirm, btw alot of thanks for youe help:fingers-crossed::good:
how much is the possibility that my fone hard drive got corrupted as its not going into recovery. I'm in doubt bcz my fone had required factory reset for no reason about once in a month
Your phone does not have a hard drive .
But its possible that the memory has a corrupt section .
But your symptoms are more likely an app causing the problem .
Thanks to all for their help, problem solved as it was connectivity issue i have tried on another pc it worked like a charm. Cheers to all
Related
iam useing odin and i have all the files downloaded and when i hit start it says
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SPH-D700-DI18-8Gb-REL.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
and it wont load pass that will someone plz help me
Tyler145 said:
iam useing odin and i have all the files downloaded and when i hit start it says
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SPH-D700-DI18-8Gb-REL.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
and it wont load pass that will someone plz help me
Click to expand...
Click to collapse
Are you sure your phone is in download mode? (press one and power..)
and dont you need usb debugging on for odin?
Power off your phone, disconnect the cable from both ends, close Odin, boot back into Download Mode, reopen Odin, connect the cable, try again.
Please post questions in Q&A. This is not the Q&A section.
soryy for posting here and yes it in download mode and i have did that already i unplug it alot and plug it back in
Use a non-stock USB cable.
iam useing a blackberry cord
Tyler145 said:
soryy for posting here and yes it in download mode and i have did that already i unplug it alot and plug it back in
Click to expand...
Click to collapse
Redownload odin and usb drivers and tar file....are u sure its in the PDA section?
i redownload everything 3 times and yes it i have it in the pda i done this b4 and it worked fine for me but idk whats wrong i been trying for hours
Tyler145 said:
i redownload everything 3 times and yes it i have it in the pda i done this b4 and it worked fine for me but idk whats wrong i been trying for hours
Click to expand...
Click to collapse
Use these:
Odin/PIT
EC05 TAR
Switch to a different USB port, and if that doesn't work, a different PC.
Have you tried restarting your Computer/ changing USB ports (use the back ones if it's a desktop).
i have those downloaded and i have change everyport and i dont have a diff pc only 1
Tyler145 said:
i have those downloaded and i have change everyport and i dont have a diff pc only 1
Click to expand...
Click to collapse
Got any friends?
i tryed on a friend pc and it did not work idk whats wrong should i just call sprint to get a new cell ?
Tyler145 said:
i tryed on a friend pc and it did not work idk whats wrong should i just call sprint to get a new cell ?
Click to expand...
Click to collapse
No. Try a different USB cable, different from the one you're using (don't care what it is). Try Heimdall. Remove the battery from the phone and leave it that way for two hours, then come back and try again. Switch up the order you're connecting between device and PC. Make sure the TAR is in the right place.
ok thanks i will post back in 2 hours i will unplug the batt for a while
Also try to reboot the pc afther installing odin and see if that works
Sent from my SPH-D700 using XDA Premium App
And if all else still fails, try running Odin with the battery removed from the phone...
Pull Battery from Phone,
Connect USB Cable to Phone,
Start Odin,
Boot Phone into Download Mode by holding 1 and Power (with battery still removed),
Flash .tar file.
I normally don't have issues when using Odin, but the few times I have had Odin fail on me (in multiple attempts consecutively), I have then been successful by pulling the battery out and flashing again.
What version of Odin are you using? I have been using 1.6 which has always seemed to work. Here is a good place with lots of Odin advice and files:
http://forum.xda-developers.com/showthread.php?t=773032
My S4 GT-i9500 went out of battery last night and now it wont boot. I'm on PA 4.4 beta 1.
Although I can enter download mode only when my phone is connected to the PC but odin is not recognizing it.
Also if I disconnect it from the computer, my phone goes blank again.
Please help!!
Guys any possible solution to revive this phone or should I head towards the service center???
u_kansal said:
Guys any possible solution to revive this phone or should I head towards the service center???
Click to expand...
Click to collapse
Try reinstalling samsung drivers or kies to get odin to recognize the phone,
if Odin works again then you can try and flash stock firmware for your device
possible fix is to disable personalized message
I had same problem since KitKat 4.4.2 ( FNB8).
I think I fixed it by disabling personalized message on lock screen
1. go to Setting/LockScreen/Lock screen widget
2. disable personalized message by selecting clock
It doesn't sound like a software problem.
My guess is either your battery (is the battery swollen?) or a hardware problem.
Stefan0vic said:
Try reinstalling samsung drivers or kies to get odin to recognize the phone,
if Odin works again then you can try and flash stock firmware for your device
Click to expand...
Click to collapse
I reinstalled kies but odin is still not recognizing.
u_kansal said:
I reinstalled kies but odin is still not recognizing.
Click to expand...
Click to collapse
Why do you assume it's a software problem? If your battery ran out and now you can't boot, then the chances that it's a software problem is something like 0,1%.
Your battery is probably damaged, try a new battery.
Lennyz1988 said:
Why do you assume it's a software problem? If your battery ran out and now you can't boot, then the chances that it's a software problem is something like 0,1%.
Your battery is probably damaged, try a new battery.
Click to expand...
Click to collapse
Well I tried a different battery,but still I can't pass the "Samsung Galaxy S4 GT-i9500" screen. It blinks once, stays for about 5-7 seconds and then the phone shuts off.
I also can't access the recovery.
Can someone send me the correct PIT files for GT-i9500 or the link plzzz now.
I managed to connect it with odin I believe my phone is soft bricked. So flashing stock firmware, but getting an error, no PIT partition found.
Guys I'm getting this error in odin
Plz help
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9500XXUFNC1_I9500ODDFNC1_I9500DDUFNA4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Hy Guys! so recently i have bought a galaxy s4 and i think it is the i9505 model becouse under the battery it is nothing written...
So i have seen that the phone dosen't get a lot of signal and i have seen that the KERNEL was modified, also when i boot up my phone in the left corner it says written with red : KERNEL IS NOT SEANDROID ENFARCING" and with yellow "SET WARANTY BIT : KERNEL", also in the "DOWNLOAD MODE" ABOVE THE NORMAL WRITING IT SAYS GRAYED OUT : WRITE PROTECTION : ENABLED" AND "eMMC BRUST MODE ENABLED" so i tried downloading the stock firmwere from sammobile.com for it and in odin it always give me a big fail when i try to write the stock firmwere, all the settings are setted to default i have not changed anything ! .
So this is the log :
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUFNB8_I9505COAFNB1_I9505XXUFNB8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sbl1.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
and after it on the left corner of the screen of my S4 it writes with RED :
"START [224, 1440]"
'SECURE CHECK FAIL : sbl1"
please help me i dont know that much
Why do you only think its an i9505? Isnt that something you should confirm before buying?
The model number is in the about phone section
Why have you flashed a rom when you arent sure what model you have?
Is kies installed?
What firmware was the phone originally on?
DSA said:
Why do you only think its an i9505? Isnt that something you should confirm before buying?
The model number is in the about phone section
Why have you flashed a rom when you arent sure what model you have?
Is kies installed?
What firmware was the phone originally on?
Click to expand...
Click to collapse
Thx for replay! so my phone when i bought it was on the 4.4.2 Kit Kat and that is the firmwere that i wanted to flash to it, i am saying that I am not shure what model is becouse in the model section it was writen i9505 but I was not 100% shure....
when ODIN gived me the error that i showed you the phone could not boot up any more, only the LED blinked permanently with blue so i have flashed with succes using ODIN the CWM and using CWM i have sucessfuly instaled Cyanogenmod now, but i wanted on the original stock Samsung firmwere .
I have tried reflashing now but no succes
P.S :
I dont think that the phone was on the original 4.4.2 by samsung becouse it had a wierd bootlogo. and in the rom i could delete stock apps
AND YES i have KIES instelled
In the download mode you can find your model number. So make sure you have an i9505 before you flash.
Almost all Odin errors can be resolved by the following:
- Different usb port
- Different cable
- Reinstall drivers
- Make sure Kies is not running in the background.
This ^
thx
Lennyz1988 said:
In the download mode you can find your model number. So make sure you have an i9505 before you flash.
Almost all Odin errors can be resolved by the following:
- Different usb port
- Different cable
- Reinstall drivers
- Make sure Kies is not running in the background.
Click to expand...
Click to collapse
Hey ! I have tried reinstalling the drivers, changhing the cable and the usb port also i tried another PC but it still dosen't work
Have you disabled kies in your task manager
DSA said:
Have you disabled kies in your task manager
Click to expand...
Click to collapse
YES I have ! I dunno what to do )
festy22 said:
YES I have ! I dunno what to do )
Click to expand...
Click to collapse
Mate ,
Use this app to find out what you have....
https://play.google.com/store/apps/details?id=org.vndnguyen.phoneinfo&hl=en
works great.
Hi,
My wife's phone SM-G935F started to bootloop after a normal update. It goes to the loading screen (IMG 1) and just stays there. The only thing I can do from there is VolDown+Power to reset or Voldown+Home+Power to Recovery mode.
Can't access factory reset mode, and the only other thing i've been able for it to show is the light-blue screen with the "!" simbol and "Try using Smart Switch Recovery..." which didn't work.
IMG1= https://s11.postimg.org/w6vna4mwz/20161029_180455.jpg
I Don't exacly know the region of the phone, but i think it is the Trinidad and Tobago one (International unlocked bought from B&H).
Anyone knows how to know region from a cell you can't boot?
Also don't know if OEM was active or not, but i think this is the problem. If i can't boot the cell, hoy to disable OEM prot?
When I try to ODIN it shows this:
http://postimg.org/image/4yyt2sd1b/
And then it FAILS
I don't know what more to do.
My odin active options are:
Auto Reboot
F. Reset Time
And the phome screen goes from this:
http://postimg.org/image/qwqoiu2nz/
To displaying this
http://smg.photobucket.com/user/brava/media/20150902_012011_zpsjm9lr9np.jpg.html
Just instead of RECOVERY, it says BOOT.
I successfully updated the bootload so the "!" simbol and "Try using Smart Switch Recovery..." screen isn't showing anymore, but the bootloop is still going. Cant update the AP, CP not CSC.
Anyone has any idea what can i do?
This phone was running Marshmelow, never had been rooted and never used custom roms in it. It was only 3 months old. Think of the children
Thanks
smart switch will work if you download the drivers to your computer. this step is necessary to allow smart switch to see your phone.
then use smart switch, click on more, emergency recovery, then device initialization.
followinstructions, it should take about 5 minutes to recover your phone, if you have input the correct information.
Cosmic Blue said:
smart switch will work if you download the drivers to your computer. this step is necessary to allow smart switch to see your phone.
then use smart switch, click on more, emergency recovery, then device initialization.
followinstructions, it should take about 5 minutes to recover your phone, if you have input the correct information.
Click to expand...
Click to collapse
Does the phone needs to be in download mode? or in the loading screen is ok?
Only 3 options I have are:
Boot screen (galaxy screen)
Powered Off
Download mode.
I can't reach any other screens.
Thanks!
Sedado77 said:
Does the phone needs to be in download mode? or in the loading screen is ok?
Only 3 options I have are:
Boot screen (galaxy screen)
Powered Off
Download mode.
I can't reach any other screens.
Thanks!
Click to expand...
Click to collapse
Loading screen is fine as long as smart switch can see your phone, the procedure should work.
I was in the same position once.
what have u chosed in odin? this look like bootloader is broken
Cosmic Blue said:
Loading screen is fine as long as smart switch can see your phone, the procedure should work.
I was in the same position once.
Click to expand...
Click to collapse
Smart Swich is working as ****. it doesn't load the recovery screen even if the phone is not connected
Any idea how to make it work=?
Windows 7 x64 here.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1101)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> param.bin
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Here is my ODIN log when I try to BT/AD my phone.
Sedado77 said:
Here is my ODIN log when I try to BT/AD my phone.
Click to expand...
Click to collapse
This is the case when i try to AD everytime. I'm quite sure my problem is the region of the firmware, but i can't know WHICH firmware to download. I called the US store where i bought it and they told me it was from Vietnam.
Got the Vietnam Stock Firmware (XXV) and it still is "Blocked by FRP Lock" when it tryies to do the recovery.img file...
Anyone knows how to get the region of the phone from the serial/imei or any other meens whith a soft bricked phone?
I tried SmartSwitch but it had the same problem. I think it used the region from the BL/CSC i flashed to it instead of the original one...
Also, the radio from the Vietnam version didn't match my phone...
Any ideas?
I can't take it to the manufacturer, i bought it online from H&M in the US and I live in South America.
HELP!!!:crying::crying:
load Odin 3.1.2.3
load Samsung_G935x_QC_Rooted_BOOT.TAR
Power off Phone ( hold Power + Vol down) ..... hold Power+Home+Vol down to enter Download mode....
connect S7 Edge to Computer ( DL Mode)
open Odin as an Administrator (!!) - right click on Odin-
put "Samsung_G935x_QC_Rooted_BOOT.TAR" in Odin
Flash
if it won`t work... try a samsung kernel... without root
I have same problem as OP help ? I had 7.0 update but it only made my phone restart, now i flashed official with odin and now stuck in bootloop... can only seem to access download mode, smart switch if i try connect says my phone is not supported.. what the hell to do now ???
So, my Galaxy J5 Prime G570F switched off suddenly while I was using it. Since then, it only loads to Download Mode (Vol - + Power + Home) and shows Downloading, do not turn off target. I downloaded the stock rom files from xda and tried various versions of Odin with no success. Each time, Odin gets stuck on Initialization and my phone screen just shows the same Downloading. I noticed FRP and Secure Download are enabled. I have tried different USB ports and am using the original USB cable that came with it.
I even tried the old Odin 1.86 and here's the log from that:-
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_G570FXXU1CRH9_CL14263629_QB19595919_REV00_user_low_ship.tar.md5 is valid.
<OSM> AP_G570FXXU1CRH9_CL14263629_QB19595919_REV00_user_low_ship_meta.tar.md5 is valid.
<OSM> CP_G570FXXU1CRH8_CL909798_QB10643368_SIGNED.tar.md5 is valid.
<OSM> CSC_OJV_G570FOJV1CRH9_CL14263629_QB19595919_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
Please help.
vistatech9895927087 said:
<ID:0/003> Can't open the serial(COM) port.
Click to expand...
Click to collapse
Odin is is failing to recognize the usb port/device. Is the COM box blue?
You could try to install the samsung drivers at
https://developer.samsung.com/galaxy/others/android-usb-driver-for-windows
I had the same issue and the drivers solved it.
Sent from my SM-J530G using XDA Labs
scroll-lock said:
Odin is is failing to recognize the usb port/device. Is the COM box blue?
You could try to install the samsung drivers at
https://developer.samsung.com/galaxy/others/android-usb-driver-for-windows
I had the same issue and the drivers solved it.
Click to expand...
Click to collapse
Yes, the COM box is turning blue and I tried installing different drivers with no luck.
vistatech9895927087 said:
Yes, the COM box is turning blue and I tried installing different drivers with no luck.
Click to expand...
Click to collapse
hmm, is it possible to exit download mode and enter in the stock recovery?
Its weird because you did not flashed anything to brick it, maybe something got corrupt and a factory reset could help.
Sent from my SM-J530G using XDA Labs
scroll-lock said:
hmm, is it possible to exit download mode and enter in the stock recovery?
Its weird because you did not flashed anything to brick it, maybe something got corrupt and a factory reset could help.
Click to expand...
Click to collapse
I tried getting into the recovery (vol + + home + power) but it just won't boot. The only combination that works is vol - + home + power and it loads into download mode. I have been trying to fix this for some time now.
Please help someone!
same problem any body knows the solution
vistatech9895927087 said:
Please help someone!
Click to expand...
Click to collapse
1234devil said:
same problem any body knows the solution
Click to expand...
Click to collapse
How are things??
Ummm what Android os version was you on when you device suddenly shut down its self... just try latest oreo from other countries or trying to flash a combination firmware ... or else use other tool like octopus or Samsung zx box to flash your firmware
---------- Post added at 07:47 PM ---------- Previous post was at 07:41 PM ----------
1234devil said:
same problem any body knows the solution
Click to expand...
Click to collapse
Ummm what Android os version was you on when you device suddenly shut down its self... just try latest oreo from other countries or trying to flash a combination firmware ... or else use other tool like octopus or Samsung zx box to flash your firmware