Welcome
This is the first time i am creating a post so if i have done any grammatical mistake while writing down the post then i am sorry but other than that no body else has a right to scold me for any thing. I have been posting videos on youtube about our device but many people find it very difficult to understand what is being don in the video so i decided write down a post on one of the most popular community.
Problems reported after flashing the stock rom (MM).
1. Volte gone
2. Second sim not working (baseband error).
Solution
1.To solve the volte problem you have to be on stock rom and stock recovery so if you don't know how to flash stock rom then go and check out my video tutorial on youtube
Link ->>https://www.youtube.com/watch?v=z7r-iQv1OA4&t
Once you have done that then you need to type this code in your phone dialler ####682# and select the country code.
for Example i will be selecting IN
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Then the phone will reboot after updating the patch and you will be able to use Volte.
Solution to problem no 2.
For this solution you have to install latest QPST tool.
Once installed go into this folder
-->C:\Program Files (x86)\Qualcomm\QPST\bin
and then open the software named as Download.
Then click the restore tab .
At this point switch off the phone and the click and hold the volume + and power button together .
Once a menu appears in blue screen asking to boot in several modes just leave it there and connect it to the computer.
The connected port should appear in the port section.
This means the device is connected in diagnostic mode
Now select the qcn file and click start.
Problem solved
Receiving error message
Every time I try to restore my QCN files using QFIs it says Invalid commnad received from phone ... What is the real problem and when I try to restore via QPST it just says checking phone connection (repeats) and failed to restore QCN... What to do
try it only on stock mm rom
it doesn't work on nougat
K6
Maybe I am using wrong file... Link me original Stock ROM... Will try on that
How to enable diagnostic mode
After flashing qcn via qpst my serial number is changed how can i fix it
Plz help
subhadeep99 said:
After flashing qcn via qpst my serial number is changed how can i fix it
Plz help
Click to expand...
Click to collapse
Your imei too have changed, that you can fix using hex editor and converting your imei to hex and replace in existing qcn file using any hex editor, and flashing qcn again with proper imei, you can change the serial no in same qcn file but its not a big issue it will not create any problem,
---------- Post added at 06:48 PM ---------- Previous post was at 06:46 PM ----------
[email protected] said:
How to enable diagnostic mode
Click to expand...
Click to collapse
By powerin up your phone with pressing vol. Up की and power key, the blue screen emerges is diag mode
But after flash qcn file using qpst download my serial no is not changed it was same as previous only imei changed?
subhadeep99 said:
But after flash qcn file using qpst download my serial no is not changed it was same as previous only imei changed?
Click to expand...
Click to collapse
Open any hex editor and place the qcn with with you have converted your imei In it and search the existing serial number in it and replace it with your device serial no and save it as you have done with your imei and flash that qcn again using qpst tool
But serial number is not a hex code so how can I find it in my qcn file
subhadeep99 said:
But serial number is not a hex code so how can I find it in my qcn file
Click to expand...
Click to collapse
Brother first of all flash the qcn which you have downloaded and note down the serial no which came with that qcn, then open hex editor and search the serial no you have noted which was in qcn, now replace it with your device serial no. Which you can found it on various imei checker website,
Now after editing serial no reflash it using qpst tool,
Serial no. Is not written in hex form it will be numeric form you can easily search it in hex editor app and replace it and save it to reflash
QNC file of K6 note
arajanrai said:
Welcome
This is the first time i am creating a post so if i have done any grammatical mistake while writing down the post then i am sorry but other than that no body else has a right to scold me for any thing. I have been posting videos on youtube about our device but many people find it very difficult to understand what is being don in the video so i decided write down a post on one of the most popular community.
Problems reported after flashing the stock rom (MM).
1. Volte gone
2. Second sim not working (baseband error).
Solution
1.To solve the volte problem you have to be on stock rom and stock recovery so if you don't know how to flash stock rom then go and check out my video tutorial on youtube
Link ->>https://www.youtube.com/watch?v=z7r-iQv1OA4&t
Once you have done that then you need to type this code in your phone dialler ####682# and select the country code.
for Example i will be selecting IN
Then the phone will reboot after updating the patch and you will be able to use Volte.
Solution to problem no 2.
For this solution you have to install latest QPST tool.
Once installed go into this folder
-->C:\Program Files (x86)\Qualcomm\QPST\bin
and then open the software named as Download.
Then click the restore tab .
At this point switch off the phone and the click and hold the volume + and power button together .
Once a menu appears in blue screen asking to boot in several modes just leave it there and connect it to the computer.
The connected port should appear in the port section.
This means the device is connected in diagnostic mode
Now select the qcn file and click start.
Problem solved
Click to expand...
Click to collapse
Do you have link of QNC file of K6 note k53a48, i have same problem with K6 note, please help me. tks you
after flashign qcn using qpst...both sims are not wrking...any solution?????
Link to qcn file
That's my first post on Lenovo k6 forum so a newbie question
The last update for our phone was k33_s231_171114_ROW i have only found a single link that provide qcn file for this version and most importantly mentions the 2gb variant k33a48
can any experienced user confirm that the link and method here are 'ok' that'll be great help
Link to flash file
link to method
Please use Google translate like i did.
Another thing if someone can guide me following the method above will also change my serial number and iemi right? If yes then what can i do to prevent it
Last thing my region is PAK which i think doesn't matter as it can be changed after fresh qfil flash.
If these questions gets answered this post can also work as the update to op.
Related
Hi everyone .
Today I get the w10 for phone TP update but sadly I saw that my phone has no signal !
now I remember that IMEI lost problem may cause this no signal issue .
I checked *#06# code and it returns me error !
I checked settings -> about too and there where no registered IMEI !
Is there any registry tweek or anyway to recover my L920 IMEI ? please :crying:
very strange ! I received WP 10 TP -> Os version : 10051.12534
but seems others get 10.01.12534 !
and also their settings like this :
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
but mine is still like wp8.1 !!!!!!!
sorry I can't take screenshot ! Screen Shot doesn't work on my build !!
sorry Seems I create this topic in wrong forum .
So sorry
hello? imei saved on dpp. It is removed with jtag or riff box. instruc. : http://4pda.ru/forum/index.php?showtopic=411852&view=findpost&p=27906734
original files:
reksden said:
hello? imei saved on dpp. It is removed with jtag or riff box. instruc. : http://4pda.ru/forum/index.php?showtopic=411852&view=findpost&p=27906734
original files:
Click to expand...
Click to collapse
I didn't use box on my phone but i have unlocked mtp on my phone . so I have to copy these files on dpp ?
ngame said:
Hi everyone .
Today I get the w10 for phone TP update but sadly I saw that my phone has no signal !
now I remember that IMEI lost problem may cause this no signal issue .
I checked *#06# code and it returns me error !
I checked settings -> about too and there where no registered IMEI !
Is there any registry tweek or anyway to recover my L920 IMEI ? please :crying:
very strange ! I received WP 10 TP -> Os version : 10051.12534
but seems others get 10.01.12534 !
and also their settings like this :
but mine is still like wp8.1 !!!!!!!
sorry I can't take screenshot ! Screen Shot doesn't work on my build !!
Click to expand...
Click to collapse
Factory settings or hard reset solution
I got the same problem.
now fix the problem (Factory settings or hard reset solution) :good:
pdaimatejam said:
Factory settings or hard reset solution
I got the same problem.
now fix the problem (Factory settings or hard reset solution) :good:
Click to expand...
Click to collapse
so damn this build
I will lost mtp hack :|
ngame said:
so damn this build
I will lost mtp hack :|
Click to expand...
Click to collapse
Lumia Software Recovery Tool. Run connect USB
Os version: 10051.12534 Update
reksden said:
hello? imei saved on dpp. It is removed with jtag or riff box. instruc. : http://4pda.ru/forum/index.php?showtopic=411852&view=findpost&p=27906734
original files:
Click to expand...
Click to collapse
In case of Ativ S IMEI is on one of MODEM_FS partitions. And not on DPP. It should be bug in reading IMEI, but IMEI itself should be ok.
-W_O_L_F- said:
In case of Ativ S IMEI is on one of MODEM_FS partitions. And not on DPP. It should be bug in reading IMEI, but IMEI itself should be ok.
Click to expand...
Click to collapse
Yup , Hard reset where solve the problem .
It seems only a read IMEI Bug and only wants to let me lost my MTP hack
feherneoh said:
For me, Win10 says "Not for resale", mobile data and airplane mode switches cannot be switched on, but mobile data is active all the time....
Previous build was better. First time I installed new build, I did not get some apps, like Spartan, I had both WP8.1 and Win10 settings....
AND Recovery Tool bricks the phone, when trying to downgrade (flashing error after 100%, I could reflash the phone from commandline using thor2)
Lumia 520
Click to expand...
Click to collapse
not for resale means many things !
in your device means you are using a pre-release version of OS that's not recommended for Retail phone .
for more info open up Non-Production Errors.txt on your pc or with a simple text editor on your phone .
you will see detailed reasons of why you see this Note !
feherneoh said:
For me, Win10 says "Not for resale", mobile data and airplane mode switches cannot be switched on, but mobile data is active all the time....
Previous build was better. First time I installed new build, I did not get some apps, like Spartan, I had both WP8.1 and Win10 settings....
AND Recovery Tool bricks the phone, when trying to downgrade (flashing error after 100%, I could reflash the phone from commandline using thor2)
Lumia 520
Click to expand...
Click to collapse
on mine L520...my mobile data and flight can enable and disable...im do hard reset 3 times...on start up i choose language english united state and next step is usual but skip on sign in outlook...
Sent from my C9660 using XDA Free mobile app
---------- Post added at 12:59 AM ---------- Previous post was at 12:50 AM ----------
ngame said:
not for resale means many things !
in your device means you are using a pre-release version of OS that's not recommended for Retail phone .
for more info open up Non-Production Errors.txt on your pc or with a simple text editor on your phone .
you will see detailed reasons of why you see this Note !
Click to expand...
Click to collapse
yes it is,here it is
Production Self Test Log
// This log file describes test failures from the Production Self Test.
// If you see this log file, it means that this device is not ready to ship
// because some of the production self tests are failing. If this is a pre-production
// device, this is an expected result and this file can be ignored (or deleted). If this
// is supposed to be a production ready device, check the log below to identify tests that
// are failing, and see the Windows Phone documentation for information on how to fix the
// issues identified by these tests.
TEST FAIL: SBCP Policy Publisher mismatch
TEST FAIL: PRERELEASE: Pre-Release software - Not approved for release
Sent from my C9660 using XDA Free mobile app
Hello guys.
I am really tired of looking for a fix for my problem. I am asking for help rarely and today is that day that I need your fast help with fixing my phone.
So...
I wanted to create a backup of 2 partitions - modemst1 and modemst2.
I have used the command "reboot nvbackup" - phone restarted, but no files created in backup and restarted already without IMEI code, and then I realized that phone is not recognizing SIM card.
First thing I have thought of - okay, lets reflash this thing. That's what I did, never with a success. I have tried flashing the original Samsung software into my phone, no help.
Tried to enter to service mode to fix it - nope - just blank window with rows, probably because SIM is not recognized.
Full wipe? Didn't help. Busybox and GSII_Repair neither.
Then by browsing root stuff I found out that I am missing 2 files:
- /dev/block/mmcblk0p10
- /dev/block/mmcblk0p11
I think that might be a problem which needs to be fixed. (I have tried to backup those two files, with no success, and as it seems, I have probably deleted the accidentally)
I was thinking if someone can back those blocks up and send the images to me so I can somehow recover those two files (Lollipop)
I have no backup of EFS folder.
I have tried to flash the modem.bin from stock firmware, no luck, no fix.
So I am looking for help from you guys, you are my last hope to get that thing fixed.
Problems to fix:
No SIM detected
No GSM signal
Unknown Modem version
Null IMEI
Missing files in /dev/block folder
EDIT: I promise that I will create a guide if I will fix it. But I need to fix it by tomorrow.
It will be nice if somebody can make an image of working EFS partition of his/her Note 3 and send it to me. After that I will check out if it works.
Almost 100 views, and still no answer? Is it that bad?
You need download file PIT and flash fw
JustCinek1 said:
Hello guys.
I am really tired of looking for a fix for my problem. I am asking for help rarely and today is that day that I need your fast help with fixing my phone.
So...
I wanted to create a backup of 2 partitions - modemst1 and modemst2.
I have used the command "reboot nvbackup" - phone restarted, but no files created in backup and restarted already without IMEI code, and then I realized that phone is not recognizing SIM card.
First thing I have thought of - okay, lets reflash this thing. That's what I did, never with a success. I have tried flashing the original Samsung software into my phone, no help.
Tried to enter to service mode to fix it - nope - just blank window with rows, probably because SIM is not recognized.
Full wipe? Didn't help. Busybox and GSII_Repair neither.
Then by browsing root stuff I found out that I am missing 2 files:
- /dev/block/mmcblk0p10
- /dev/block/mmcblk0p11
I think that might be a problem which needs to be fixed. (I have tried to backup those two files, with no success, and as it seems, I have probably deleted the accidentally)
I was thinking if someone can back those blocks up and send the images to me so I can somehow recover those two files (Lollipop)
I have no backup of EFS folder.
I have tried to flash the modem.bin from stock firmware, no luck, no fix.
So I am looking for help from you guys, you are my last hope to get that thing fixed.
Problems to fix:
No SIM detected
No GSM signal
Unknown Modem version
Null IMEI
Missing files in /dev/block folder
EDIT: I promise that I will create a guide if I will fix it. But I need to fix it by tomorrow.
Click to expand...
Click to collapse
one more solution.
You need download firmware have 5 files. inside have file .pit and flash it using Odin. Step-by-step flash it. this is wrong/error partition EFS. or you need download file .pit for your device exp: .pit N9005 using only for N9005, you choose PIT location on odin. Remember you need tick to Re-Patition.
Good Luck!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Your stuff didn't help me at all, sorry. It was the same after these things which You told me. But I have fixed it and you can mark this thread as solved. I am currently writing a guide what to do to fix that stuff.
Required tools:
1. Sp Flash tool mod edit - link removed
2. Drivers mod edit - link removed
3. Firmwares: K50a40mod edit - link removed
Other Varients:mod edit - link removed
4. Windows pc
5. Lenovo K3 Note(ofcorse )
Before doing this, Take Nvram(imei) backup:mod edit - link removed
Download all required files, then unzip.
install drivers, if device not showingin spflash tool(put your pc advanced startup with driver signature enforcement then install drivers)
Stock rom Installation process:
1.Open sp Flash tool.
goto options(located on top left corner)
then select download, in DA DL ALL checksum options tick on both>> USB checksum and Storage checksum(close this window)
2. select scatter-Loading-File from firmware folder.
3. select Download only. (if u select format all+download your imei numbers will be gone)
4. Then click on download button.
5. switch off your mobile, then remove battery and re insert it, then connect
Big right mark will appear after success.
Follow all instructions carefully,
Don't blame me if anything went wrong.
plz download drivers from given link.
use latest spFlashTool.
Press Thanks if my process work.
Thumbs up.:good:
Hi man,
at first I want to thank you, this helped me to unbrick my phone, but ofcourse I did deleted my IMEI, SN and so on.
I know there are few ways how to change it, but none seems to work for me so far. I have the right drivers (v 1.1.13), but not any program is able to connect to my phone except to SP flash tool.
So my question is. Is there any way how to root this version of andriod?
I have already tried Kingroot, RomasteruSU, framaroot and not even MTK Engineering mode was not able to help me change IMEI.
Thanks in advance
M
enterthename said:
Hi man,
at first I want to thank you, this helped me to unbrick my phone, but ofcourse I did deleted my IMEI, SN and so on.
I know there are few ways how to change it, but none seems to work for me so far. I have the right drivers (v 1.1.13), but not any program is able to connect to my phone except to SP flash tool.
So my question is. Is there any way how to root this version of andriod?
I have already tried Kingroot, RomasteruSU, framaroot and not even MTK Engineering mode was not able to help me change IMEI.
Thanks in advance
M
Click to expand...
Click to collapse
https://forum.xda-developers.com/k3-note/help/null-invalid-imei-permanent-fix-100-t3472491
follow this tutorial..
panuganties said:
https://forum.xda-developers.com/k3-note/help/null-invalid-imei-permanent-fix-100-t3472491
follow this tutorial..
Click to expand...
Click to collapse
Hi,
tried to do exactly what is there, but still no luck. I had only APDB before, so I hoped to be successfull this time with MD1_DB.
But what happened. I already had drives and SN writer (2.1504), but downloaded older version (1.1728) anyway. Got into point where phone was connected and in meta mode. The newer version of SN Writer gave me error message pretty fast and calceled meta mode. See SN writers error message img. below.
I have also tried older version, it took bit more time, then it asked me to fill my IMEI for a second time, but ended up with error message again after that. The only thing different was that phone stayed in meta mode. Put second print screen error as well.
Any suggestions?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
enterthename said:
Hi,
tried to do exactly what is there, but still no luck. I had only APDB before, so I hoped to be successfull this time with MD1_DB.
But what happened. I already had drives and SN writer (2.1504), but downloaded older version (1.1728) anyway. Got into point where phone was connected and in meta mode. The newer version of SN Writer gave me error message pretty fast and calceled meta mode. See SN writers error message img. below.
I have also tried older version, it took bit more time, then it asked me to fill my IMEI for a second time, but ended up with error message again after that. The only thing different was that phone stayed in meta mode. Put second print screen error as well.
Any suggestions?
Click to expand...
Click to collapse
press and hold volume- and insert usb cable..
thread closed until the download links will be available
my Sharp Aquos M1 (FS8001) is not opening as some handy travel software is install , i want to root and change its firmware ...
need help.
can anyone provide me stock firmware, rom
even i cannot on usb debugging
pls help
Do you know the IMEI/barcode number of the phone? It's normally 10 digits beginning with a 3. I can use it to find the firmware for you.
superscooby said:
Do you know the IMEI/barcode number of the phone? It's normally 10 digits beginning with a 3. I can use it to find the firmware for you.
Click to expand...
Click to collapse
imei 3561120715589457
s/n - MS1GLMA720701854
the phone is a sharp m1 fs8001
i have the same problem... any one can help me find a stock room ? thanks .
hello
i found this site :
http://guideroot.net/sharp-m1-download-the-firmware-android-8-0-o/#lollipop
i downloaded all firmware from this site, but i get error when writing each of them.
maybe others will be more lucky !
same problem handy travel software handy locked ?
Sharp fs8001
My Sharp Aquos M1 (FS8001) is not opening as some handy travel software is installed
need help.
Please I need your help
How many of these phones do you have?
The company has collapsed and there are lots of these phones out there now.
I have the ROM + flashing tool used by the Handy company to flash back to Android.
Proof:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Not sure if I should upload the ROM for free.
HandyPhone said:
How many of these phones do you have?
The company has collapsed and there are lots of these phones out there now.
I have the ROM + flashing tool used by the Handy company to flash back to Android.
Proof:
Not sure if I should upload the ROM for free.
Click to expand...
Click to collapse
I have one, could you please help me?
SOLVED.
Here's the ROM and flashing tool I used: mega.nz/#F!bWBnhYQb!BjHVHTxJRYwYMCB8id7M7w
This is the instructions I followed: androidmtk.com/flash-stock-rom-using-smart-phone-flash-tool
I got android up and running fine, however the IMEI's are missing when and it does not connect to network when I put in a sim.
At the bottom of the previous guide it says there is another guide to load the IMEI's on. Here's the link to that guide: androidmtk.com/use-sn-write-tool
I got stuck on Step 9 as I don't have the AP and MD files. I tried a bunch of files I could find through Google but nothing gave me the pass.
So I found an alternative way to get the IMEI by extracting the MD file from this guide: Youtube.com/watch?v=N6i7Zln1rCE and then loading it through Maui META (this guide forum.hovatek.com/thread-12328.html
Now the IMEI is there and I have signal but mobile data does not work.
I hope this helps you. Please let me know if it works for you or if you found any other way to get it working completely. I need some help getting the mobile data working myself so any tips would be greatly appreciated.
Actually the problem was my simcard wasn't detecting the network properly so I just had to manually input the APN.
Here is the file I used with Maui META (with this guide forum.hovatek.com/thread-12328.html) to load the IMEIs onto the phone: mega.nz/#!eGwiiCQB!ZqHYbc8Y11R6HVa87Wr1k-dOeYk2I10U9MDIzGRchF0
still having a nvram warning: err = 0x10 error on the wifi but seems to work fine!
Enjoy
HandyPhone said:
SOLVED.
Here's the ROM and flashing tool I used: mega.nz/#F!bWBnhYQb!BjHVHTxJRYwYMCB8id7M7w
This is the instructions I followed: androidmtk.com/flash-stock-rom-using-smart-phone-flash-tool
I got android up and running fine, however the IMEI's are missing when and it does not connect to network when I put in a sim.
At the bottom of the previous guide it says there is another guide to load the IMEI's on. Here's the link to that guide: androidmtk.com/use-sn-write-tool
I got stuck on Step 9 as I don't have the AP and MD files. I tried a bunch of files I could find through Google but nothing gave me the pass.
So I found an alternative way to get the IMEI by extracting the MD file from this guide: Youtube.com/watch?v=N6i7Zln1rCE and then loading it through Maui META (this guide forum.hovatek.com/thread-12328.html
Now the IMEI is there and I have signal but mobile data does not work.
I hope this helps you. Please let me know if it works for you or if you found any other way to get it working completely. I need some help getting the mobile data working myself so any tips would be greatly appreciated.
Click to expand...
Click to collapse
Oh, previous I encountered a problem of "PMT changed for the ROM, it must be downloaded". But it is easily to fix, just click the "Format" tab, and format it, the problem will be fixed.
And the problem of invalid IMEI, after I put new SIM card into the phone, the problem will be fixed. Thank you very much for you help!
how much does it cost for 1 phone? [email protected]
Gimana cara pasang twrp di sharp m1, mohon pencerahannya master
HEY GUYS
we know that after 11/9/2018 we can not do patch cert because the new security
this way can restore original imei in addition to restore the second imei too
now let us start the steps
first flash recovery twrp
enter the phone to recovery
then choose MOUNT
and make mount efs
go back
then chose ADVANCED
File Manager
chose EFS folder
on the bottom right of the screen mark
chose delete
then back and enter to download mode directly
and flash U3 combination file download from here
now format it from recovery
then reboot to system
we notice message tell us there is error in efs folder and reboot press reboot
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
the phone will restart and the orginal imei has restored
now root the phone by kingo root (Temporary root) this root is gone when reboot system
after root open z3x tool (you can use cracked z3x 29.5) and make backup cert (read cert )
and we edit the cert that we backed up it tow
to know how to edit the cert go to this
open cert file with notepad++
you see like this :
;Z3X Samsung CERT file
;Please do not edit this file
[cert]
Model=SM-G930F
SerNo=R5xxxxxxxx
IMEI=355xxxxxxxxxxxx
ImeiSign=xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
PubKey=xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
PubKeySign=xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Click to expand...
Click to collapse
copy lines from imei to pubkeysign and add after imei number 2 and after imeisign number 2 and PubKey ,PubKeySign to look like this
;Z3X Samsung CERT file
;Please do not edit this file
[cert]
Model=SM-G930F
SerNo=R5xxxxxxxx
IMEI=355xxxxxxxxxxxx
ImeiSign=xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
PubKey=xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
PubKeySign=xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
IMEI2=355xxxxxxxxxxxx
ImeiSign2=xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
PubKey2=xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
PubKeySign2=xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Click to expand...
Click to collapse
HERE VIDEO HOW TO EDIT CERT DOWNLOAD HERE
after that re write the cert that edited by z3x tool (write cert)
now flash the phone official rom
to repair wrong SN (Serial Number):
Open Root Explorer and grant access to superuser
Change mount R\W in root
Open folder root\efs\FactoryApp and find the "serial_no" file
Open in text editor and change the value with your correct serial number, you can look at behind
Save the file and make sure the serial_no permission 0644 rw-r--r--.
Reboot your phone
and enjoy you get s7 g930F DS WITH LAST SECURITY PATCH
If you like my work then please buy me coffee
https://www.paypal.me/FANIONDZ
can i get ur number mon frère
mrnot said:
can i get ur number mon frère
Click to expand...
Click to collapse
in private message
Absolutely brilliant!!
The only part where I got a bit lost was, installing Kingo on theFactory Image. That can be done by downloading the Kingo for PC version, and rooting the phone over USB.
Be aware that the Kingo software installs a bunch of other crap on your PC that you should uninstall later.
can we convert on custom rom or just only in stock rom?
krook1 said:
Absolutely brilliant!!
The only part where I got a bit lost was, installing Kingo on theFactory Image. That can be done by downloading the Kingo for PC version, and rooting the phone over USB.
Be aware that the Kingo software installs a bunch of other crap on your PC that you should uninstall later.
Click to expand...
Click to collapse
Can you tell if it works with custom roms too ?
I might root my phone and lose on samsung pay just for this
I wish to convert my single sim s7edge to a dual sim variant.
What exactly do I need ?
thanks bro done on G930L custom rom Batmanrom
but my mobile sim tray not supported dual sim
Hi Guys, sorry if this is not 100% the correct thread, but you seem to be able to answer my question:
Can I easily copy the IMEIs from one S7 (SM-G930FD dual sim from china) to another S7 (SM-G930F) and vice versa? Do I need to follow all the steps or is there a easier solution, maybe just backup one phone and restore it to the other?
Any help is appreciated!
Nickkal said:
can we convert on custom rom or just only in stock rom?
Click to expand...
Click to collapse
Yes You can convert custom or stock rom
max414 said:
Can you tell if it works with custom roms too ?
I might root my phone and lose on samsung pay just for this
I wish to convert my single sim s7edge to a dual sim variant.
What exactly do I need ?
Click to expand...
Click to collapse
Yes it's work with custom rom too
Just make all steps
Proper z3x link that is working?
Nickkal said:
Proper z3x link that is working?
Click to expand...
Click to collapse
Use this link here
And use this password for this file
Technical Computer Sloutions
Pass....technical.....not working
sorry
it is working
.......Solutions
thnks
Sent from my SM-G965F using Tapatalk
working like a treat! Many thanks mate! I just modified my single SIM tray using a razor blade to make room for the second SIM.
I use the rom from team exykings my phone can't be unlocked and added new sim, anyone help please?
Can i try ?
My modle is sm-g930s
Offical oreo update ...
Can i try ur way ?
Plz help..
dhoom-2 said:
My modle is sm-g930s
Offical oreo update ...
Can i try ur way ?
Plz help..
Click to expand...
Click to collapse
Your phone is powered by the Exynos 8890*
And yes you can convert
Check your security bit
wow thanks
fanion said:
Your phone is powered by the Exynos 8890*
And yes you can convert
Check your security bit
Click to expand...
Click to collapse
im gonna try it now ,
cant wait... :silly:
i have 2 questions ...
is ur combination file(in the link) work with my modle ?
and i hv no gsm box,so i have to use z3x without box crck.. is it ok?
oh , i hv download the U3 combination file file ...
but its not showing in odin ... and its not opening ...
why is that ? what should i do ?
can any one give me U3 combination file plzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzz