After I root my device (redmi 4 prime), my phone don't connect to pc.
only connect in charging mode & I can't to access in MTP mod ...
mehdi1986 said:
After I root my device (redmi 4 prime), my phone don't connect to pc.
only connect in charging mode & I can't to access in MTP mod ...
Click to expand...
Click to collapse
Did you try to just reboot the device while having USB debbuging on? This works fine for me in such cases
Sent from my P11 using Tapatalk
Yes, i try it but doesn't work ?
mehdi1986 said:
Yes, i try it but doesn't work ?
Click to expand...
Click to collapse
Yo Buddy I was using MIUI 8.1.2.0? As far as I can remember I had the same issue I was only able to access MTP only via TWRP, but after I flashed LOS(Now I am using Mokke) I was albe to access MTP normally. So your best bet is to flash another ROM
Just add these 2 lines to your build.prop file and MTP will work again:
persist.service.adb.enable=1
persist.sys.usb.config=mtp,adb
Make sure you have USB Debugging enabled.
mehdi1986 said:
After I root my device (redmi 4 prime), my phone don't connect to pc.
only connect in charging mode & I can't to access in MTP mod ...
Click to expand...
Click to collapse
Follow this Thread
SAFI_AFRIDI said:
Follow this Thread
Click to expand...
Click to collapse
Thanks, it's work ...
or use Magisk for rooting, it works for me
Hello everyone,
I know this subject is discussed quite often all over the forum, but there is a small difference between the described cases an mine.
The problem is, my redmi 4 prime won't connect to my pc for mtp. Only charging is available. It doesn't offer me to choose between the other options. So far, so known.
Now comes the big BUT:
My phone isn't rooted. Only the bootloader is unlocked but the problem occurred before the bootloader was unlocked.
Since my phone isn't rooted, the common solutions like changing the superuser app or editing the build.prop file won't work.
I noticed, that my phone connects if I turn it off, plug it in and boot it up. So if the phone is connected while the phone restarts it's working. When disconnected again and reconnect afterwards, still only charging is possible.
If this thread is placed in the wrong forum, I apologize.
I'm thankful about every answer.
Happy new year
EdgarKater
Try changing the usb cable or use different usb port of the pc. For me, sometimes mtp doesn't work for a bad usb connection.
kibria.mgk said:
Try changing the usb cable or use different usb port of the pc. For me, sometimes mtp doesn't work for a bad usb connection.
Click to expand...
Click to collapse
Thx but I've already tried this and it won't work.
Related
Hey guys,
I currently recently installed a custom ROM from this website and for some reason now when I plug in my USB into my PC it comes up not being detected so when I put my phone as hard drive so I want to transfer music, it doesn't detect it. Can anybody help me if this is ROM problem or just my USB?
Hey,
Okay I disabled USB debugging didn't know it was on, still doesn't work says windows cannot find USB device not reconginzed when I connect the USB. For the Reinstalling usb driver I do not know how to this ~?
i have the same problem.. turn "fast boot" off and restart the phone.. this always works for me.. hope this helps
Hey, I turned fastboot off. Doesn't work. I ordered new usb cable.. hopefully this works and it was just a fault with the cable!
Sent from my Desire HD using XDA App
Usually this is a problem with the cable. Simple, cheap to fix. Keep your old cable around for charging though (nice to have a spare)
Is this problem with the USB still active?
If so try a different PC just in order to eliminate WinOS issues.
If not close.
Hi,
I have the same problem at some months ago. I tried the cable and pfone on another PC, and it works fine. So, I recommend to try it on another PC and reinstall your Windows.
brgs,
Herold
Had the same propblem! Turns out it was the usb cable, it charged fine with the cable but data transfer didnt work.
i also had the same problem since last week and still cant resolve till now...i try all the option that u gave(change cable/pc,turn off fastboot)....i even sent my phone to shop and they still cant detect.they said maybe the usb port is damage or some software that may block my usb port?is it true? anyone can help?????
necrs said:
i also had the same problem since last week and still cant resolve till now...i try all the option that u gave(change cable/pc,turn off fastboot)....i even sent my phone to shop and they still cant detect.they said maybe the usb port is damage or some software that may block my usb port?is it true? anyone can help?????
Click to expand...
Click to collapse
What happened last week? Is that when you got the phone? Or installed a different rom? etc.
Grant Barker said:
What happened last week? Is that when you got the phone? Or installed a different rom? etc.
Click to expand...
Click to collapse
before this is ok.just last week i remember that i pull the usb cable from the phone quite hard.but i don think that the usb too sensitive that will break by that.still can charging... but not detected in pc
I had similar problem and it was hardware, I sent it back to Vodafone and they sent me a replacement!
I am running CM7 now its awesome.
Andy
USB BRICK in my INSPIRE 4G ( DESIRE HD)
Hi, all
I got a new inspire 4g last week.( equivalent to desire hd ). It was working fine. But now it does not detect the USB connection. It only charges when I connect to pc. No other issues. I have also noticed that during fast boot mode also pc does not recognize the phone as device. I have tried all the suggestion on xda but no luck.
As fastboot is also not detected by PC I could not format mtd0 and reconfigure it.
Can anybody have any other idea? If I change the main board how much cost will incur ??
Thanks all.
Grant Barker said:
What happened last week? Is that when you got the phone? Or installed a different rom? etc.
Click to expand...
Click to collapse
musarraf172 said:
Hi, all
I got a new inspire 4g last week.( equivalent to desire hd ). It was working fine. But now it does not detect the USB connection. It only charges when I connect to pc. No other issues. I have also noticed that during fast boot mode also pc does not recognize the phone as device. I have tried all the suggestion on xda but no luck.
As fastboot is also not detected by PC I could not format mtd0 and reconfigure it.
Can anybody have any other idea? If I change the main board how much cost will incur ??
Thanks all.
Click to expand...
Click to collapse
First of all.. you have HTC Sync installed right?
Happened to me initially as well.. although for me changing the cable and/or changing the USB port on the PC solved the issue. Have you tried these?
Also sometimes killing all apps on the device before connecting helped.
You can try accessing your device through ADB to see if its being detected.
And I really dont think you'll need to change the main board..
USB brick on my Inspire 4G
Thanks for your reply. When I go the phone ADB and Fastboot were working
well. There was no driver issue. Now even PC also does not detect the phone or any new hardware when I connect it to pc. I had working fastboot on both win7 and Linux (ubuntu) pc. Now in both OS the phone is not detectable. Windows device manager does not see any new hardware when I connect my inspire . dmesg also does not show my hardware when I connect my inspire to linux pc.
Please help or suggest me to investigate further. I know how to install and work with adb and fastboot as well as Clockwork recovery ( also ext recovery). Some people suggested to flash a new radio. I can flash the new radio via sdcard. But how safe is it ? My phone is S-off and made unbranded. Will flashing a new radio make my phone locked AT&T again? ????
Thanks a lot
if4ct0r said:
First of all.. you have HTC Sync installed right?
Happened to me initially as well.. although for me changing the cable and/or changing the USB port on the PC solved the issue. Have you tried these?
Also sometimes killing all apps on the device before connecting helped.
You can try accessing your device through ADB to see if its being detected.
And I really dont think you'll need to change the main board..
Click to expand...
Click to collapse
As far as I know.. USB problem has no relation whatsoever to Radio. Radio is only concerned with the signal stuff. Flashing it isn't that risky if you follow the instructions... There's a thread in the development section about Radio's which explains it pretty nicely.
As for the USB problem, are you using a Custom ROM? Some ROMs like LeeDroid have USB detection problem which can be solved simply by flashing a different kernel like LordMod's.
What I meant by "Accessing through ADB" was if commands like "adb remount" or any adb command as such are working when your phone is connected to the PC? Or is it showing "error: device not found"?
recently my pc stopped recognizing my moto x pure, when ever i plugged it in.
image of message when trying to connect it to pc. https://gyazo.com/46462150a83c04bbda51efb98904dd68
i have the drivers installed already and i retried to uninstall and reinstall the drivers.
i tried many usb cables and ports. still not working. it charges the phone but will not do anything els.
Don´t use an usb hub connect it directly to the usb port.
cpagallardo said:
Don´t use an usb hub connect it directly to the usb port.
Click to expand...
Click to collapse
I'm trying connect it to the back of pc USB ports, no luck sometimes it won't even show up anything.
Sent from my XT1575 using Tapatalk
StreetkillnHD said:
I'm trying connect it to the back of pc USB ports, no luck sometimes it won't even show up anything.
Sent from my XT1575 using Tapatalk
Click to expand...
Click to collapse
does it sound when you connect it?
What OS are u using?
have u install ADB Drivers?
did your pc/laptop recognize flashdrivers?
cpagallardo said:
does it sound when you connect it?
What OS are u using?
have u install ADB Drivers?
did your pc/laptop recognize flashdrivers?
Click to expand...
Click to collapse
The only thing it does when inplug it in is charges..
I recently flashed back to stock mm I was running trupure it was fine then it would connect and recognized by PC.
I have installed and installed adb driver many times.
My PC does recognize my other phone LG g3.
Sent from my XT1575 using Tapatalk
StreetkillnHD said:
The only thing it does when inplug it in is charges..
I recently flashed back to stock mm I was running trupure it was fine then it would connect and recognized by PC.
I have installed and installed adb driver many times.
My PC does recognize my other phone LG g3.
Sent from my XT1575 using Tapatalk
Click to expand...
Click to collapse
Reinstall ubs host driver (Not the cellphone one)
Use another cable.
Put your Phone in MTP mode in the options above when asking just charge or transfer pictures MTP or Mass Storage.
cpagallardo said:
Reinstall ubs host driver (Not the cellphone one)
Use another cable.
Put your Phone in MTP mode in the options above when asking just charge or transfer pictures MTP or Mass Storage.
Click to expand...
Click to collapse
how do a reinstall usb host driver,
i also tried 5 different usb cables before no difference..
it never asks anything when i plug my phone in, nothing pops up in the notification like it should.
StreetkillnHD said:
how do a reinstall usb host driver,
i also tried 5 different usb cables before no difference..
it never asks anything when i plug my phone in, nothing pops up in the notification like it should.
Click to expand...
Click to collapse
Tap on the "Charging mode" notification when your USB is connected and you'll get a pop-up that let's you select MTP mode.
Alternatively you can go to Device Manager and look for any error icons (think they're yellow triangles - been a while since I used a PC). Right click and uninstall all the offending ones, the disconnect and reconnect your device via USB.
Sent from my XT1575 using Tapatalk
rickbosch said:
Tap on the "Charging mode" notification when your USB is connected and you'll get a pop-up that let's you select MTP mode.
Sent from my XT1575 using Tapatalk
Click to expand...
Click to collapse
Nothing shows up about that notification. No notification at all.
still havent fixed this issue..
Pull down menus / enable mtp
lafester said:
Pull down menus / enable mtp
Click to expand...
Click to collapse
like i been saying theres nothing in the pull down, no notification about my phone being pluged in just just the battery icon charging in status bar
Did you do a full wipe?
StreetkillnHD said:
like i been saying theres nothing in the pull down, no notification about my phone being pluged in just just the battery icon charging in status bar
Click to expand...
Click to collapse
In a lot of MM roms, you have to go in to developer options and select MTP under 'MTP configuration' in there. Even if it's selected already, tap it again and it should pop up asking what to do when device is connected on the pc. $5 says that does the trick. Easy but surprisingly tough one. One other problem I'm running into lately with the new windows 10 is that it has driver signing enabled by default and often rejects the driver you install or just doesn't use it even if it's installed. So if the driver is the problem (or more accurately windows 10 is refusing to acknowledge the installed driver), you might need to disable driver signing enforcement. Here's a link how to do that: http://www.howtogeek.com/167723/how...8.1-so-that-you-can-install-unsigned-drivers/
benjmiester said:
In a lot of MM roms, you have to go in to developer options and select MTP under 'MTP configuration' in there. Even if it's selected already, tap it again and it should pop up asking what to do when device is connected on the pc. $5 says that does the trick. Easy but surprisingly tough one. One other problem I'm running into lately with the new windows 10 is that it has driver signing enabled by default and often rejects the driver you install or just doesn't use it even if it's installed. So if the driver is the problem (or more accurately windows 10 is refusing to acknowledge the installed driver), you might need to disable driver signing enforcement. Here's a link how to do that: http://www.howtogeek.com/167723/how...8.1-so-that-you-can-install-unsigned-drivers/
Click to expand...
Click to collapse
Okay yes i tried the mtp in dev options , didnt work at all still not recognized, ill try the other thing u said.
StreetkillnHD said:
Okay yes i tried the mtp in dev options , didnt work at all still not recognized, ill try the other thing u said.
Click to expand...
Click to collapse
Weren't you having quick charge problems too? Is it possible your phone's USB port has a hardware problem?
jason2678 said:
Weren't you having quick charge problems too? Is it possible your phone's USB port has a hardware problem?
Click to expand...
Click to collapse
Maybe yes
but i hope not, but it seems that way
Did you ever flash the stock factory images?
Guess you can't if the comp doesn't recognize
lafester said:
Did you ever flash the stock factory images?
Guess you can't if the comp doesn't recognize
Click to expand...
Click to collapse
I did flash stock mm and that's when this started happening, I flashed stock mm because I was having issues with turbo charge on a ROM I was using. But flashing back to stock mm didn't help and now I can't even connect my phone to my PC..
Hi, I tried to search in Help Forum about my issue, but did not get a thread on the same.
hence starting a new topic, please help me.
My phone doesn't get recognized on PC or Laptop via usb. So I need to root it via app or any method used with Phone.
If there is any, let me know.
I tried KingRoot and Root Zenfone app, didnt worked.
AFAIK, you can't do that. You need to use computer to root it. Is your usb port damaged? Try clean it up first. Or sometimes it could be just Windows driver issue.
kopter36 said:
AFAIK, you can't do that. You need to use computer to root it. Is your usb port damaged? Try clean it up first. Or sometimes it could be just Windows driver issue.
Click to expand...
Click to collapse
Thank you for your reply, USB port of my device is fine; i can see charging is happening. I tried several ports of Lappy, it says USB not recognized.
sandy7874 said:
Thank you for your reply, USB port of my device is fine; i can see charging is happening. I tried several ports of Lappy, it says USB not recognized.
Click to expand...
Click to collapse
Try to reinstall drivers, or you can install Asus PCLink (that automatically installs Intel USB drivers).
sandy7874 said:
Thank you for your reply, USB port of my device is fine; i can see charging is happening. I tried several ports of Lappy, it says USB not recognized.
Click to expand...
Click to collapse
Did you tried plugging in to another computer to see if it works? Try using different cable that certified for data transfer. Make sure you check "mtp" as your preferred connection method. If computer still says "USB device not recognized", probably your phone usb port might have broken solder connection.
kopter36 said:
Did you tried plugging in to another computer to see if it works? Try using different cable that certified for data transfer. Make sure you check "mtp" as your preferred connection method. If computer still says "USB device not recognized", probably your phone usb port might have broken solder connection.
Click to expand...
Click to collapse
I tried Asus PC link, and it didn't recognized my Device. Seems there is a problem.
sandy7874 said:
I tried Asus PC link, and it didn't recognized my Device. Seems there is a problem.
Click to expand...
Click to collapse
I guess that might be hardware issue as you already installed Asus PCLink on your computer. Did you already tried fastboot mode? Try going into droidboot menu and plug your phone. If it shows up in device manager, then you are all good.
However if it does not work, and if you have a good eyes and basic soldering skill, you might want to disassemble your phone and inspect the USB port solder connections. You might have to replace the bottom board too if you accidentally fried any caps on it.
You can't root your zen5 without pc......
There are 2 methods
sandy7874 said:
Hi, I tried to search in Help Forum about my issue, but did not get a thread on the same.
hence starting a new topic, please help me.
My phone doesn't get recognized on PC or Laptop via usb. So I need to root it via app or any method used with Phone.
If there is any, let me know.
I tried KingRoot and Root Zenfone app, didnt worked.
Click to expand...
Click to collapse
Hey sandy, first check your Android Version. If it is 4.3 or lower then you can root without pc. But if you have an android version higher than that then you will need a pc.
To root without pc:
You can do a simple search on youtube as I already upgraded my Android Version
To root with pc:
Use a reliable tutorial I myself used on youtube:
As I am a new member i cannot give the link but the name of the youtuber is Silicon Rodent
Best of luck:good:
Hi,
since one of the latest Oxygen OS updates, my OnePlus 5 is not able to connect to any PC anymore as long as USB-Debugging is enabled. It's not showing up in Device-Manager nor lsusb on multiple PCs, I've tried rebooting multiple times, safe mode, clearing settings data, but nothing seems to have changed it's behavior - when turning on USB Debugging, all USB connections seem to get lost, including data and charging. A curious thing I noticed is that the Android-System notification that lets you switch USB modes sticks around when unplugging in this state, even after disabling debugging again, until the phone is restarted.
Is this a common issue? I haven't been able to find anything about it on XDA or on their official product forums which seem to be pretty dead, but it's a pretty big problem for me since I need this phone for app development.
Thanks!
armibu said:
Hi,
since one of the latest Oxygen OS updates, my OnePlus 5 is not able to connect to any PC anymore as long as USB-Debugging is enabled. It's not showing up in Device-Manager nor lsusb on multiple PCs, I've tried rebooting multiple times, safe mode, clearing settings data, but nothing seems to have changed it's behavior - when turning on USB Debugging, all USB connections seem to get lost, including data and charging. A curious thing I noticed is that the Android-System notification that lets you switch USB modes sticks around when unplugging in this state, even after disabling debugging again, until the phone is restarted.
Is this a common issue? I haven't been able to find anything about it on XDA or on their official product forums which seem to be pretty dead, but it's a pretty big problem for me since I need this phone for app development.
Thanks!
Click to expand...
Click to collapse
Open beta or stable? Which version exactly?
strongst said:
Open beta or stable? Which version exactly?
Click to expand...
Click to collapse
I'm running the current stable Oxygen OS 5.1.5(ONEPLUS A500_23_180808), unrooted. I'll try installing the new beta, since fastboot mode still gets recognized by PCs.
Ok, so beta 19 didn't change anything about it - still the same issue and behavior when unplugging. Not sure what else to do other than trying to wipe it, which would be pretty annoying
I have the same problem and I can not solve it neither with usb debuginc or mtp and I see that Oneplus is not bothering att all about this problem. I need to transfer some data from my computer to my phone and I am stucked. I am thinking sending to warranty or sell it! I was a big fun but now........
lhoria46 said:
I have the same problem and I can not solve it neither with usb debuginc or mtp and I see that Oneplus is not bothering att all about this problem. I need to transfer some data from my computer to my phone and I am stucked. I am thinking sending to warranty or sell it! I was a big fun but now........
Click to expand...
Click to collapse
You have not the same problem... Op wants to transfer data while usb debugging is on. But it works only when usb debugging is off.
Yes I have. O tried all the combination but it is just not working, with debugging on or off. I should aopreciate litle help.
Thank you
lhoria46 said:
Yes I have. O tried all the combination but it is just not working, with debugging on or off. I should aopreciate litle help.
Thank you
Click to expand...
Click to collapse
The op can transfer files with USB debugging disabled. You can not. So you have another issue please read OP again
Thanks smart guy but can I solve this problem? Even op want to transfer data from pc to the phone and reverse with usb debugg off I can not. It is written usb not recognize.
Thank you in advance.
armibu said:
Ok, so beta 19 didn't change anything about it - still the same issue and behavior when unplugging. Not sure what else to do other than trying to wipe it, which would be pretty annoying
Click to expand...
Click to collapse
lhoria46 said:
Thanks smart guy but can I solve this problem? Even op want to transfer data from pc to the phone and reverse with usb debugg off I can not. It is written usb not recognize.
Thank you in advance.
Click to expand...
Click to collapse
I'm on OB19, rooted with magisk 17.2 and with USB debugging enabled or disabled im getting file transfer working on 2 win10 pc's.
The pop-up is immediately present after plugging into USB port(original cable or other USB cable).
Msybe: Toggling file transfer to charging and back can help you?
strongst said:
I'm on OB19, rooted with magisk 17.2 and with USB debugging enabled or disabled im getting file transfer working on 2 win10 pc's.
The pop-up is immediately present after plugging into USB port(original cable or other USB cable).
Msybe: Toggling file transfer to charging and back can help you?
Click to expand...
Click to collapse
I've tried this a few times, the options in that pop-up don't have any effect whatsoever after enabling USB debugging and unplugging/plugging the phone back in. Also tried changing the default setting, which doesn't seem to have any effect either though.
Same for me. No effect att all. I don't lnpw what to do. I have a lot of files in storage and I can not root my phone and try another Rom.
Help!!!
I have done all the possibel combinations.
armibu said:
I've tried this a few times, the options in that pop-up don't have any effect whatsoever after enabling USB debugging and unplugging/plugging the phone back in. Also tried changing the default setting, which doesn't seem to have any effect either though.
Click to expand...
Click to collapse
lhoria46 said:
Same for me. No effect att all. I don't lnpw what to do. I have a lot of files in storage and I can not root my phone and try another Rom.
Help!!!
I have done all the possibel combinations.
Click to expand...
Click to collapse
Have you tried another PC, checked your driver, firewall etc?
Common issue across all devices
Just a suggestion.
Yes I did it on two Pc and with two diffrent cables. One day it worked 3 minutes and the problem suddenly came back without takig off the cabel from Pc.
lhoria46 said:
Yes I did it on two Pc and with two diffrent cables. One day it worked 3 minutes and the problem suddenly came back without takig off the cabel from Pc.
Click to expand...
Click to collapse
And you have which oxygenOS version?
The latest update OEM 8.1.0 version OPC O2 19 BETA but the problems begun before loadin this uodate. The reason I put this one was exact that I wasn't able to do nothing.
lhoria46 said:
The latest update OEM 8.1.0 version OPC O2 19 BETA but the problems begun before loadin this uodate. The reason I put this one was exact that I wasn't able to do nothing.
Click to expand...
Click to collapse
Really strange... OOS 5.1.5 and OB19 and before.
Never had any issues and also others not report such issues
Hi guys,
Im having a hard time. Hope u guys can help me.
I wanted to start from scratch so i wiped everything, inclusive internal storage within twrp .
So far no problem, but when i tried to connect my OP5 to PC my PC doesnt recognize it. I guess its something with my pc.
Why doesnt my pc recognize my OP5? I cannot do anything right now.
In device manager i cannot find my op5.
Praying for help
Langenl said:
Hi guys,
Im having a hard time. Hope u guys can help me.
I wanted to start from scratch so i wiped everything, inclusive internal storage within twrp .
So far no problem, but when i tried to connect my OP5 to PC my PC doesnt recognize it. I guess its something with my pc.
Why doesnt my pc recognize my OP5? I cannot do anything right now.
In device manager i cannot find my op5.
Praying for help
Click to expand...
Click to collapse
Have a look at here https://forum.xda-developers.com/oneplus-5/help/fastboot-wont-recognize-device-t3866942
strongst said:
Have a look at here https://forum.xda-developers.com/oneplus-5/help/fastboot-wont-recognize-device-t3866942
Click to expand...
Click to collapse
The drivers are installed. When i plug my OP5 in the PC i dont hear or see anything.
The problem is i cannot go into the OS because i have no OS to change USB debugging mode.
Also tried different usb type c cable's
adb doesnt recognize
fastboot doesnt recognize
pc doesnt recognize
Langenl said:
The drivers are installed. When i plug my OP5 in the PC i dont hear or see anything.
The problem is i cannot go into the OS because i have no OS to change USB debugging mode.
Also tried different usb type c cable's
Click to expand...
Click to collapse
You should try to go to fastboot and connect it since it loads low level drivers. Have you read the linked post and tried the steps?
strongst said:
You should try to go to fastboot and connect it since it loads low level drivers. Have you read the linked post and tried the steps?
Click to expand...
Click to collapse
I've editted my response. fastboot and adb doesnt recognize aswell.
Langenl said:
I've editted my response. fastboot and adb doesnt recognize aswell.
Click to expand...
Click to collapse
Is it possible that my connector is broken? Phone is charging though….
I'm really desperate atm ;(
Langenl said:
Is it possible that my connector is broken? Phone is charging though….
I'm really desperate atm ;(
Click to expand...
Click to collapse
Sure, that's possible, you can try to mount an usb otg stick or similar otg within twrp.
strongst said:
Sure, that's possible, you can try to mount an usb otg stick or similar otg within twrp.
Click to expand...
Click to collapse
Really hope thats not the case.
I simply cant check OTG within Twrp->mount when connected to pc. Aint got another OTG device. I hope there is some other way i can fix my problem because i dont want to spend money on repairing my connector. Thanks for your effort!
Langenl said:
Really hope thats not the case.
I simply cant check OTG within Twrp->mount when connected to pc. Aint got another OTG device. I hope there is some other way i can fix my problem because i dont want to spend money on repairing my connector. Thanks for your effort!
Click to expand...
Click to collapse
OTG won't work if connected to a PC, only storage and controller devices, no clients. you need a USB stick or similar, please do some research about usb OTG if it's not clear
strongst said:
OTG won't work if connected to a PC, only storage and controller devices, no clients. you need a USB stick or similar, please do some research about usb OTG if it's not clear
Click to expand...
Click to collapse
Sorry misunderstanding. Anyways...i just borrowed a USB stick wich support otg but still the same problem. cant select otg.
Langenl said:
Sorry misunderstanding. Anyways...i just borrowed a USB stick wich support otg but still the same problem. cant select otg.
Click to expand...
Click to collapse
If you have a chance to simply try it on another PC, do it. Otherwise Firewall, drivers etc should be your next focus.
Langenl said:
Sorry misunderstanding. Anyways...i just borrowed a USB stick wich support otg but still the same problem. cant select otg.
Click to expand...
Click to collapse
Pushed the USB stick a litthe further and it works. My connector isnt the best anymore but im glad it works. Massive thank you!
Langenl said:
Pushed the USB stick a litthe further and it works. My connector isnt the best anymore but im glad it works. Massive thank you!
Click to expand...
Click to collapse
Glad you got it working now! Maybe you can edit the tread title and add [SOLVED] at the beginning to help others solve their issues
I am having the same problem: no mtp, no adb, no fastboot, no otg
The phone charges with dash without any problems. I already tried 3 different computers (win 10 and Linux mint). Cant think of anything else than a Hardware issue of my USB Port.
My biggest problem is not getting adb, so i can't install twrp at the moment.
Are there any recommendations for me?
derschnelle said:
I am having the same problem: no mtp, no adb, no fastboot, no otg
The phone charges with dash without any problems. I already tried 3 different computers (win 10 and Linux mint). Cant think of anything else than a Hardware issue of my USB Port.
My biggest problem is not getting adb, so i can't install twrp at the moment.
Are there any recommendations for me?
Click to expand...
Click to collapse
I hope you read the thread already?
strongst said:
I hope you read the thread already?
Click to expand...
Click to collapse
Yes I did and the difference between OP and me is the non functional OTG.
I just thought you guys might have another ace up your sleeves.
derschnelle said:
Yes I did and the difference between OP and me is the non functional OTG.
I just thought you guys might have another ace up your sleeves.
Click to expand...
Click to collapse
You need a working USB port,if that won't be fixed, nothing can be done...
strongst said:
You need a working USB port,if that won't be fixed, nothing can be done...
Click to expand...
Click to collapse
I'm not really sure, whether my port is broken or not. Shortly after I posted here, I found out, that I missed the Standard USB-Protocol-Setting in developer options (it was checked as charge). So I changed it and voila, USB worked!
But then I tried to install twrp (which was successful at first, but seems to be overwritten again by stock recovery) and now I can't get my device to connect again. I tried to disconnect, connect with other PCs, change the usb-debugging and standard usb-protocoll, connect in fastboot-mode, nothing works.
derschnelle said:
I'm not really sure, whether my port is broken or not. Shortly after I posted here, I found out, that I missed the Standard USB-Protocol-Setting in developer options (it was checked as charge). So I changed it and voila, USB worked!
But then I tried to install twrp (which was successful at first, but seems to be overwritten again by stock recovery) and now I can't get my device to connect again. I tried to disconnect, connect with other PCs, change the usb-debugging and standard usb-protocoll, connect in fastboot-mode, nothing works.
Click to expand...
Click to collapse
It's me again, I solved my problem!
When I tried to connect yesterday I noticed that my phone always charged and then immediately stopped charging again. It was charged to ~80% and didn't go any further. So I thought maybe the battery calibration is faulty, which can happen when you never fully charge. So I emptied the battery, charged it while phone off and tadaaa everything works.
It seems my phone interrupted the usb connection because it tried to charge my phone over 80% and the controller stopped it.
derschnelle said:
It's me again, I solved my problem!
When I tried to connect yesterday I noticed that my phone always charged and then immediately stopped charging again. It was charged to ~80% and didn't go any further. So I thought maybe the battery calibration is faulty, which can happen when you never fully charge. So I emptied the battery, charged it while phone off and tadaaa everything works.
It seems my phone interrupted the usb connection because it tried to charge my phone over 80% and the controller stopped it.
Click to expand...
Click to collapse
Very interesting but it might be possible. Thanks for posting the solution