I connected my kw88 and updated the clock computer. The update went smoothly, but the clock was turned off and did not turn on again. I pulled out the battery connection but it did not open on the yine. I press the opening key at the time but it does not react to the guest.
Related
Hi everyone,
There is something strange going with my X1 (WiMo 6.1). While i have my phone connected to my pc for a sync the phone switches off after 30/40 seconds when i do not touch the screen...
This behavour is new and i don't know to get it back to the before state that is during a sync or being connected to the pc the phone does not switch off...
Is there a setting to change this?
Does it go off completely?
does it vibrate and shows Xperia Logo @ SE logo when turning it on again?
if not, then it might be only standby mode, where the mobile is still functional but turns off the LCD for power saving, a small press of the power button will turn it on again.
anaadoul said:
Does it go off completely?
does it vibrate and shows Xperia Logo @ SE logo when turning it on again?
if not, then it might be only standby mode, where the mobile is still functional but turns off the LCD for power saving, a small press of the power button will turn it on again.
Click to expand...
Click to collapse
It does not reset, but just powers down. Goes off. It looses the active sync connection and when you switch it back on it has to regain the active sync connection. Wich is wvery annoiing because you have to keep tickling the X1 to stay alive when you want copy some data to the device...
Any idea how to change that behavour??
was it like this the first moment you tried to sync it? or it started behaving like this? if it wasn't, then it might be a software you installed.
if you can try to hard reset (make sure you backup your mobile) then try to sync.
i think there is some conflict between active sync and another software.
boomdijk said:
Hi everyone,
There is something strange going with my X1 (WiMo 6.1). While i have my phone connected to my pc for a sync the phone switches off after 30/40 seconds when i do not touch the screen...
This behavour is new and i don't know to get it back to the before state that is during a sync or being connected to the pc the phone does not switch off...
Is there a setting to change this?
Click to expand...
Click to collapse
Is this 30/40 seconds timeout your normal timeout for going standby?
If so, maybe the setting in "Settings - System - Power" to not charge the X1 when connected to a PC is active.
Hello,
I had the same problems, wheter using active sync or usb, and even more.
No usb connection, the display did not dimm - it went directly to standby - cutting all the connections (wifi etc). I did not find out, but I think it was some programm I intalled, after a hard reset and only installing what I think what I really need, no problems anymore.
---
cu
Robert
Anyone else having this issue...
When plugging my phone in to the laptop no matter what mode I have the USB setting set to (PC Mode, Windows Media Sync, USB Mass Storage, or Charge Only) my touch screen becomes extremely buggy. The scrolling is very rough (if I can get it to scroll at all because it decides to select something instead), selects items that I'm not even close to touching, just doesn't respond to touch briefly, or locks up briefly.
It's instant too. As soon as I unplug the phone from the USB connection the responsiveness is back to normal, only needs a very light touch, and no jitters and locking. When I have the phone plugged into just a regular home or car outlet everything is fine as well using the same usb cable.
I get this in Windows XP, Vista, 7, Debian, and Ubuntu.
Edit: btw, I did the latest updates on the phone as well
Found over on the Motorola DroidX support forums an issue with the smart profile.
Turning off the smart profile helped a lot. I turned off the smart profile and powered off the phone. Disconnected the usb cable and powered the phone back up. Waited for the phone to completely load and tested the responsiveness and worked great. Plugged in the USB and seemed pretty good but with a slight hit on the sensitivity of the touch and needed a slightly more pressure. Went back into the settings and turned off the double tap to silence the phone (both smart sensor settings now off) and the phones responsiveness is now 100% back to normal in Charge only mode which was the worse mode to be in before.
PC Mode was about the best mode to be in before with the motorola MFC drivers installed but still took a hit on responsiveness. Seems like the Smart Sensor settings on my phone do not like USB. Hopefully that is fixed in 2.2.
Next question, now with all this fiddling around, every time I plug and unplug my phone even in charge only mode the verizonwireless media manager web page comes up on my laptop. Now that's annoying.
Found it. It was the MotoConnect software that was installed along with the drivers. Drivers are still installed but uninstalled the MotoConnect and the verizonswireless media manager page no longer pops up when connecting my phone.
jason2459 said:
Found over on the Motorola DroidX support forums an issue with the smart profile.
Turning off the smart profile helped a lot. I turned off the smart profile and powered off the phone. Disconnected the usb cable and powered the phone back up. Waited for the phone to completely load and tested the responsiveness and worked great. Plugged in the USB and seemed pretty good but with a slight hit on the sensitivity of the touch and needed a slightly more pressure. Went back into the settings and turned off the double tap to silence the phone (both smart sensor settings now off) and the phones responsiveness is now 100% back to normal in Charge only mode which was the worse mode to be in before.
PC Mode was about the best mode to be in before with the motorola MFC drivers installed but still took a hit on responsiveness. Seems like the Smart Sensor settings on my phone do not like USB. Hopefully that is fixed in 2.2.
Next question, now with all this fiddling around, every time I plug and unplug my phone even in charge only mode the verizonwireless media manager web page comes up on my laptop. Now that's annoying.
Click to expand...
Click to collapse
jason2459 said:
Found it. It was the MotoConnect software that was installed along with the drivers. Drivers are still installed but uninstalled the MotoConnect and the verizonswireless media manager page no longer pops up when connecting my phone.
Click to expand...
Click to collapse
The MotoConnect software puts a small system tray icon on as well. Right click that and you can turn off the VZW page if you want. Of course, un-installing MotoConnect completely works as well
Hello guys,
I got the Teclast x80hs (Windows only version) and I'm very happy with it.
Since one week, the tablet doesn't charge when turned on. Windows doesn't recognize the pluged in cable. No sound, no changing icon. When I turn it off, it charges but doesnt show a charging battery.
I tried:
- changing cable (longer, shorter)
- changing charger (power bay, div. adaptors, direct to my mbpr)
- reset windwos (I cant fully reset it, because i can only reset windows with plugged in charger..)
- resintall drivers (I deleted all battery drivers in device manager)
- reboot several times
Does anyone have a solution for this?
Teclast support doesn't answer my email.
Thank you!
Marco
Hello! I am running cyanogenmod and Timur Rom on 2012 N7. I have tasker to detect power on and power off but here's my trouble..
The N7 will only detect power when the display is on!?!?!?!
If the display is turned off or times out or is locked and I give it power, the display doesnt turn back on automatically. I turn it on manually with the lock button on the side and the battery shows no charge coming through.
With the display still on, i unplug and plug the power back in and it works fine!
I tested it on the PC. PC detects the N7 fine and sees the HDD. Even with the display off, the PC will detect the N7 and I can explore folders but the N7 still receives no power until I manually turn the screen on and unplug and plug the charger back in!
This is preventing me from doing the car dash install because I cannot depend on the N7 to turn on display automatically because it does not detect power with screen off. Only with screen on!
I have went through all settings a million times, tried every 101 troubleshooting step, and I cannot figure it out.
Please, please, please help me figure this out. It's driving me crazy! :cyclops:
I there, I got the Finow x5 plus last week and today the smart watch is suddenly stopped and will not turn on. Pushing on the buttons gives no response. Just charged it on the pc and put it on and for a moment there was the clock screen but then it turned Black and looks dead. Connecting on USB with pc gives no action. No charging or screen that pops up. Does someone has an idea how to restart the watch.
Take the back off and disconnect the battery for about 30 seconds. Then attach the cable again and try to turn it on.
I guess you already made sure that you have charged the watch?
Sent from my HTC 2PS6200 using Tapatalk