Related
Hi, I just got an atrix two days ago and today tried flashing a ROM via CWM.
After following all of the original posts instructions correctly, the phone rebooted, and would not charge, or even boot into android D:
No red LED or error message, it would just sit at the booting screen.
Another strange thing, whenever I would plug the AC adapter into the phone, it would automatically boot, also mentioned by another person which flashed the ROM...
Post: http://forum.xda-developers.com/showpost.php?p=15697608&postcount=417
Rom: http://forum.xda-developers.com/showthread.php?t=1160649
I tried using RSDlite but it says the battery is too low to flash. Same issue with Fastboot.
What should I do? I can't charge the phone, and whenever I connect it to my computer I get a solid Green LED.
Please help me D:
I'll be available via XDA PM, skype (danstheman7 is my username) and e-mail at [email protected]
Thank you in advance
**sorry if this is in the totally wrong section, i'm freaking out a bit right now and posted here incorrectly. my apologies.
You could try and get a battery charger for your battery. Ebay or amazon.
Also if your battery is really low sometimes it won't power on just buy plugging it into the wall or computer untill it has more then 10% charge. So if you plug it in and get a green light let it set a while it may be charging. Few hours should do the trick.
I am impatient so I used an old usb cable, cut the end off that would normally attach to a device, and stripped the wires that were red and black. On the back of your battery there is a positive and negative sign just attach the red to positive and the black to negative. Using tape I taped them down so they wouldnt move, plugged it in, and waited for a while for the battery to charge. Monitor the temperature of the battery to make sure it don't get hot. If it does unplug it, disconnect and order a battery charger. Something isnt right.
Once charged for a while put the battery back into the phone which allowed me to flash fastboot and RSD. Now make sure you have a full battery before doing this again.
I am not responsible for damage you inflict on yourself or phone. This can be dangerous. Electric shock, fires, exploding battery, etc may occur. Please try at your own risk. But this is what I did, ive learned my lesson to never flash on a low battery. Always charge fully.
You could also put the battery back in the phone and not have to wait for the battery to charge. Although you risk destroying your phone. And not just your battery.
Sent from my MB860 using Tapatalk
Hi. Like you mentioned I had the same issue. I managed to fix it!
Go to this thread: http://forum.xda-developers.com/showthread.php?t=1163009
Download .zip for your carrier (Att or international) and then enter to CWM Recovery:
Plug your mobile to wall charger and hold volume down button. Then press volume down until you see android recovery - press up and it will lunch CWM recovery (I'm assuming You have got CWM installed for unlocked and you have unlocked BL). Then wipe your data and simply apply zip that you have downloaded. This Solved my problem.
I don't what caused the problem but What i did was:
1. I have Unlocked BL using pudidng for international.
2. Flashed via fastboot system.img for 2.3.4 OrangeFR
3. Applied fix for RAM
4. Installed CWM for Unlocked
5. Nand Backup
6. Applied cherry blur in CWM
7. Applied RAM fix for 4.5.91
Up to this point - no problems. I restored all apps via titanium. I went to sleep and when I woke up this morning my mobile was off and I couldn't switch it on.
I have connected to the charger and then the mobile went on immediately. After few sec went off again and then on. I thought the battery is dead untill I've read this thread.
Things I can do ONLY while my mobile is connected to charger:
1. Enter fastboot - but I'v got msg that battery is to low to flash...
2. Enter CWM Recovery
3. Once I'm in CWM I can unplug from Charger and connect to PC.
3. ADB sees my device
Click to expand...
Click to collapse
To me cherry ROM drained my battery from 50% to 0% over the night and somehow I wasn't able to charge my mobile and even switch it off with the battery inside. This is strange...
I have the same problem with cherry blur... everything is perfect but battery life is suckinng
Sent from my MB860 using XDA Premium App
Faced same issue - fixed
Hey there,
i faced the same issue couple of days back. My battey was completely drained. As soon as I connected my phone to ac charge, it would star and stuck at the Moto logo without charging the battery at all. I was able to rebot my phone to recovery, but none of the recovery zip worked for me. I was not able to use flashboot since always got the low battery warning.
Finally had to order the spare battery charger from Amazon and charge my battey to boot into flashboot and flash the HKTW image. Once i flashed to HKTW i was bale to apply the latest 4.5.91 zip using CWM. Hope this helps.
Thanks,
SK
Foka002 said:
Hi. Like you mentioned I had the same issue. I managed to fix it!
Go to this thread: http://forum.xda-developers.com/showthread.php?t=1163009
Download .zip for your carrier (Att or international) and then enter to CWM Recovery:
Plug your mobile to wall charger and hold volume down button. Then press volume down until you see android recovery - press up and it will lunch CWM recovery (I'm assuming You have got CWM installed for unlocked and you have unlocked BL). Then wipe your data and simply apply zip that you have downloaded. This Solved my problem.
I don't what caused the problem but What i did was:
To me cherry ROM drained my battery from 50% to 0% over the night and somehow I wasn't able to charge my mobile and even switch it off with the battery inside. This is strange...
Click to expand...
Click to collapse
This did the trick, thank you SO much
Go to local AT&T and ask to leave your battery in a display for a few hours and come back and pick it up.
Hello! I think i bricked my phone. (MB525). With the latest Quarx CM10 everything is fine, the phone charge, etc... But randomly the phone dont charge anymore with wall charger or usb.
Now, i cant boot, the phone dont charge. When i connect to pc i see white led. With battery and wall charger i can access to bootmenu, recovery. But if i disconnect from wall charger the phone shutdown immediatly. So i cant flash any sbf via rsd lite. I try to restore an older nandroid, but nothing changed.
What can i do? Please help.....
Brother just flash or phones sbf Frm rsd lite u will search tutorial here
Sent from my MB526 using xda premium
illumanati22 said:
Brother just flash or phones sbf Frm rsd lite u will search tutorial here
Sent from my MB526 using xda premium
Click to expand...
Click to collapse
I cant flash it. Bootmenu or recovery only work with power cord on the wall. If i disconnect and try to attach the phone to pc (to flash) its shut down
XianHuen said:
Hello! I think i bricked my phone. (MB525). With the latest Quarx CM10 everything is fine, the phone charge, etc... But randomly the phone dont charge anymore with wall charger or usb.
Now, i cant boot, the phone dont charge. When i connect to pc i see white led. With battery and wall charger i can access to bootmenu, recovery. But if i disconnect from wall charger the phone shutdown immediatly. So i cant flash any sbf via rsd lite. I try to restore an older nandroid, but nothing changed.
What can i do? Please help.....
Click to expand...
Click to collapse
Hi, there!
I'm not an expert, but maybe I can give you a direction as a starting point.
Either your battery is empty and only needs to be reloaded or it is to old, so you have to get a new one.
A third posibility is, that the battery is empty and had not always contact to get loaded, but that I can't say from here and it's up to you, to check over.
And also your cable and your plug could be damaged.
Your options:
1. Reload your battery (and test its health) in another device or an external loader. You could put it in another Defy of a friend. Or bring it to a service center for cell phones for reloading.
2. You could otherwise buy an new (loaded) battery. Service center again?
3. Finally you could try the following method with the risk of a final damage to your battery:
http://forum.xda-developers.com/showthread.php?t=892026
Tell us, how it has been going for you.
Good luck!
:fingers-crossed:
XianHuen said:
Hello! I think i bricked my phone. (MB525). With the latest Quarx CM10 everything is fine, the phone charge, etc... But randomly the phone dont charge anymore with wall charger or usb.
Now, i cant boot, the phone dont charge. When i connect to pc i see white led. With battery and wall charger i can access to bootmenu, recovery. But if i disconnect from wall charger the phone shutdown immediatly. So i cant flash any sbf via rsd lite. I try to restore an older nandroid, but nothing changed.
What can i do? Please help.....
Click to expand...
Click to collapse
As long as the white LED is there, you are fine. Just charge that thing for some hours.
If you have a nandroid backup you can restore that without the battery but with the wall charger connected.
Swift2603 said:
As long as the white LED is there, you are fine. Just charge that thing for some hours.
If you have a nandroid backup you can restore that without the battery but with the wall charger connected.
Click to expand...
Click to collapse
Thank you guys! I try to charge it via usb, but the phone always started automatically after 5 minutes
That happened to me while ago, I just plug my phone to the wall charger and left it for like two hours and the battery charged quite fine.
XianHuen said:
Hello! I think i bricked my phone. (MB525). With the latest Quarx CM10 everything is fine, the phone charge, etc... But randomly the phone dont charge anymore with wall charger or usb.
Click to expand...
Click to collapse
I don't have any advice really, but just wanted to note that I've experienced something similar. I'm on the Nov 2 CMX build from Quarx.
Every couple of days, my phone won't charge when connected to wall charger or USB, signal bars never change, wifi is dead, and clock is dead. My phone basically stops functioning altogether until I reboot. Rebooting always seems to fix it for me though.
If you need advice on which SBF to flash send me a PM or something. I had to flash an SBF for the first time a month or two ago, and finding the proper SBF was the most difficult part of it all.
Thanks for the help guys, i can flash the sbf, but now i get "code corrupt" and "battery low" errors. I can charge the phone via pc, but its restart in 5 minute. I keep charging it, but after 3 hour its still "low battery" message. With wall charger, the phone enter to bootlader and 1-2 minutes later the "battery low" error disappear but no charging led. After this the phone dont have enough battery life (i keep doing this charging method for 2 hours)
Charge your battery longer.
Check the MD5SUM of your SBF
This post has been beamed to this area by quantum teleportation.
Coodarah said:
Charge your battery longer.
Check the MD5SUM of your SBF
This post has been beamed to this area by quantum teleportation.
Click to expand...
Click to collapse
I tried everything. When usb-pc in, i see the white led. 5 minutes later the phone enter to bootloader mode. Low Battery, Cant program error messages flashing. After 2 minutes the phones say "OK" and RSD lite recognize the phone! BUT! I cant do the whole flashing process, because 3 minutes later the phone shut down. If i wait to charge more in the bootloader more, its still shut down in 3 minutes.
I try to shut down the device everytime if its enter to bootloader, to charge more, but after 8 hours doing this, its still "low battery".
XianHuen said:
I tried everything. When usb-pc in, i see the white led.
[...]
I try to shut down the device everytime if its enter to bootloader, to charge more, but after 8 hours doing this, its still "low battery".
Click to expand...
Click to collapse
I think, we are at a point at which we are running in circles, my friend.
You tried just everything to reanimate your phone.
You must check your battery in ANOTHER device or load it in ANOTHER external charger to be sure that it's okay. Not in your phone and not in your PC.
If the battery charges well, then your phone is either physically damaged or bricked.
(Service Center needed)
Otherwise, if it's (battery) just charging fine and your phone boots up, first flash stock SBF and then flash what you want to.
If the battery isn't charging in that OTHER charger, then you know, you have to buy a new one.
Another thought, not very likely, but maybe your phone is damaged by overclocking/heat and suffers due to this under those permanent blackouts?
Bottom line is: you need another Defy with another battery to find out for yourself to solve your problem.
Unfortunately there is no wizardry
Question:
Is it necessary to go to boot loader for charging?
(I'm not sure about that.)
As a try, just let the phone off connected to power for a couple of hours.
__________
This post has been beamed to this area by quantum teleportation.
Thank you!
I flashed 4.5.3-109-fixed.sbf and i GOT MOTOROLA BOOT LOGO! but always bootloop.
Now, if i flash DEFYPLUS_U3_4.5.1-134_DFP-231_GR_SIGN_UCADEFYEMARAB1B80AA004.0R_PDS03C_USAJRDNGIBRRTCEE_P022_A022_Service1FF.sbf.gz
its okay? And i get fully working rom? (i know its defy+ but with the fixed sbf its partially working)
Glad to read that. This is good news :highfive:
Nope, unfortunately you won't get it running with a Defy+ SBF without having trouble/more work on your side.
Better download a MB525 SBF playing the game save. But it's your very own decision.
First see here (Maybe you already know all this stuff):
http://forum.xda-developers.com/showthread.php?t=1216982
Then, after lots of reading, swearing and understanding read on here:
http://forum.xda-developers.com/showthread.php?t=966537
_________________________________
Okay, I would take one of the MB525 SBFs from the "Android 2.2.2 "Froyo" section (3.4.2... or 3.4.3...)
NOT any Chinese SBF = no go!
But watch out for your Bootloader version (BL5, BL6) and your type of camera (red or green lense).
After flashing your stock ROM/SBF and the initial rooting, I would first make a NANDROID backup (CWM Custom Recovery) to have a clean ground.
Then I would first flash the stable CM7.2.0 and also do a NANDROID backup (CWM Custom Recovery) to have a solid home base for playing around.
Finally I would flash the latest Nightly of CM10 02.11. + Update from 07.11. completed with gapps minimal or gapps signed from 2012.10.11 (Google apps Android 4.1.2)
Much work to do for you, but remember: Even the longest way starts with only one little first step.
:fingers-crossed:
Hello everyone, i need help. Yesterday i installed cyanogen 11 rom on my milestone, but when the phone boots, it said setup wizard stopped working and i couldnt do anything, after that i flashed my device with 2.3.4 version, from 2.3.6. At that time i didnt knew that that will brick my phone. So now it wont turn on...when i put it on the charger led next to charger/usb flashes, when i connect it to usb led stays on. I read a lot threads on the forum but no luck. I just need to enter to bootloader so that i can flash it again, i tryed it with camera vol down and power but now luck. Anyone knows another way?
Thanks in advance.
I fixed it by using battery bypass. I wont delete thread maybe will help someone.
nikolacirjakovic said:
I fixed it by using battery bypass. I wont delete thread maybe will help someone.
Click to expand...
Click to collapse
How to do a battery bypass on motorola milestone 2?
sssloba said:
How to do a battery bypass on motorola milestone 2?
Click to expand...
Click to collapse
look here and here
Tnx but this don't do the magic for me.. It's the same, only LED lights up and no reaction on button press..
I'll have to try something else.
sssloba said:
Tnx but this don't do the magic for me.. It's the same, only LED lights up and no reaction on button press..
I'll have to try something else.
Click to expand...
Click to collapse
Sorry, but it worked for me...did you fixed it some other way?
Nope, not yet.
I'll try this with another cable. Also, i find a tutorial how to make Motorola factory cable, and i will try that when i find the time.
I can't put links here now, but it's called "How to Make Motorola Factory Cable to Unbrick Your Android! " on Youtube, maybe it can help someone elese.
I'm not giving up. :fingers-crossed:
sssloba said:
Nope, not yet.
I'll try this with another cable. Also, i find a tutorial how to make Motorola factory cable, and i will try that when i find the time.
I can't put links here now, but it's called "How to Make Motorola Factory Cable to Unbrick Your Android! " on Youtube, maybe it can help someone elese.
I'm not giving up. :fingers-crossed:
Click to expand...
Click to collapse
I almost killed my M2 last week, all my fault. When battery is too low, cable bypass is not enough to turn on with vol down + camera. But there is another trick in RSD lite.
Put the bypass cable in the M2 battery & phone then connect bypass cable in a wall charger (computer usb port has not power enough). Now plug the data cable in the M2 usb then connect to PC USB port. Phone still appears to be dead if you try to power on (try it). Go to RSD lite 5.7 and click "Show device" until device properties shows something. Now ignore that your phone looks powered off and go ahead flashing with RSD.
After flashing you will need to do a factory reset as usual, turning on with X pressed until triangle appears. Note that in some M2 you go to wipe menu pressing @ one or more times in triangle screen, while on other M2 you press vol up + vol down to get wipe menu.
Mine was bricked for the same reason, flashed BL, 2.3.6, then because I could not wipe (didn´t know that there was two ways to get menu), I messed up the entire thing, flashing 2.3.4 - phone dead with side led on when connected. Battery does not charge in this state, so after discharged I recovered this way.
Progress
Ok, this helps a bit......I managed to flash my M2 but still no startup screen.
When I did what you wrote, RSD Lite v5.7 did show my device and it started flashing it, in some point the screen on my phone lights up and shows "FW update in progress.." . Everything finishes nice with no trouble...rebote and PASS...
But there is no Motorola icon shown, neither I can start in recovery mode, or bootloader mode or any other that i tried.
When I connect it to PC with data cable, it makes sound like the USB device is plugged in, and it also can be seen in RSD Lite as connected device but nothing on the M2 screen... Same thing happens when i press power button on the phone while it is connected with the data cable.
Any idea why?!
By the way, tnx for helping me this much! :good:
sssloba said:
Ok, this helps a bit......I managed to flash my M2 but still no startup screen.
When I did what you wrote, RSD Lite v5.7 did show my device and it started flashing it, in some point the screen on my phone lights up and shows "FW update in progress.." . Everything finishes nice with no trouble...rebote and PASS...
But there is no Motorola icon shown, neither I can start in recovery mode, or bootloader mode or any other that i tried.
When I connect it to PC with data cable, it makes sound like the USB device is plugged in, and it also can be seen in RSD Lite as connected device but nothing on the M2 screen... Same thing happens when i press power button on the phone while it is connected with the data cable.
Any idea why?!
By the way, tnx for helping me this much! :good:
Click to expand...
Click to collapse
Excuse me, what sbf version are you trying to flash? Do you know your current BL version?
Please note that some sbf requires bootloader upgrade to 70.13 first.
And there is not direct downgrade - i.e. once flashed GB, flashing froyo bricks M2. Actually even between GB versions, once installed a R01 GB sbf you can not flash any R00 GB sbf. Some downgrades only this way.
Also there is not BL downgrade.
lampwarez said:
Excuse me, what sbf version are you trying to flash? Do you know your current BL version?
Please note that some sbf requires bootloader upgrade to 70.13 first.
And there is not direct downgrade - i.e. once flashed GB, flashing froyo bricks M2. Actually even between GB versions, once installed a R01 GB sbf you can not flash any R00 GB sbf. Some downgrades only this way.
Also there is not BL downgrade.
Click to expand...
Click to collapse
I also think he's trying to downgrade. Perhaps he flashed Latin America ROM, and now he's trying to flash UK one. I don't know, but what he describes looks exactly what I experienced when I tried to flash Froyo over GB.
IMHO he should try to flash the latest ROM, that means Latin America 2.3.6 GB.
rabinhood said:
I also think he's trying to downgrade. Perhaps he flashed Latin America ROM, and now he's trying to flash UK one. I don't know, but what he describes looks exactly what I experienced when I tried to flash Froyo over GB.
IMHO he should try to flash the latest ROM, that means Latin America 2.3.6 GB.
Click to expand...
Click to collapse
Yes, that is exactly what happened.
After reading some more about this, I now understand what was my problem....
Playing with my M2 I installed some CM versions, 10, 10.2, 11... and finally when I wanted to go back to stock rom, I find newer version than mine was, and there is the first mistake. I installed it not knowing that I can't do a downgrade later.
Secound mistake was that i TRIED to go back to my old stock rom, and....black screen happend.:crying:
But thanks to your help I now know how to fix it. And i did! :victory: :highfive:
My BL is 70.13 , and when i checked my CG31 with "smgver" it show that it is v4.
I can't go back to my old rom, but now I can install costum or some BR/AR gb except for persona&vivo,which is 4 as Endless7 explaned in his text.
Now there is only one more problem... the battery cannot be charged. There is icon like it is being charged, and also it says charging 1% and always is 1%.
I have original battery and one that is not original...neither one of those two can't be charged.
sssloba said:
(...)
Now there is only one more problem... the battery cannot be charged. There is icon like it is being charged, and also it says charging 1% and always is 1%.
I have original battery and one that is not original...neither one of those two can't be charged.
Click to expand...
Click to collapse
When connected with a wall charger a discharged battery should jump to 20% in config, battery. If locked in 1%, probably there is a mess in the battery state variable.
If you are using a custom recovery, try to clear battery state on it and select the option to fix permissions.
Doing again the master clear/factory clear also may work, but needs to config all the phone again.
Another thing to consider, any short circuit or wrong wiring while doing the bypass cable may damage the charger (or battery, or phone), do you have a spare one to test?
lampwarez said:
When connected with a wall charger a discharged battery should jump to 20% in config, battery. If locked in 1%, probably there is a mess in the battery state variable.
If you are using a custom recovery, try to clear battery state on it and select the option to fix permissions.
Doing again the master clear/factory clear also may work, but needs to config all the phone again.
Another thing to consider, any short circuit or wrong wiring while doing the bypass cable may damage the charger (or battery, or phone), do you have a spare one to test?
Click to expand...
Click to collapse
I tried both of this things, and none of them worked. When powered on, without charger, on the battery icon stands [!]
and when it is connected with a wall charger, icon changes to little lightning ( standard charging icon) inside the empty battery, without movements (battery do not changes colors, red, yellow, green). On lock screen says: Charging 1%, and same on the battery settings (1%).
That was on costum rom.
And on the stock rom in the battery icon stands [?], and when I connect it to the wall charger it says (with original Motorola battery inside):
"Invalid battery
Your device battery is invalid and cannot be charged.
Replace the battery with an original Motrola battery."
I changed the cable, and the charger, but I do not have third battery...short circuit...maybe...maybe.
One interesting fact, the battery seems to be charging, although it says 1%.
The original battery was empty at the begining, she couldn't even start the phone, and now phone is working on that battery....strange. Should it be able to do that, if there was a short circuit?
As far as I know, flashing stock sbf overwrites most config files, also battery statistics. Maybe the easiest solution would be to buy a new replacement battery - at least here, in Poland they go for 7-8$ - quite cheap IMO.
I remember when I was using MS2 that once I had this question mark instead of battery status - it heppened when I drained battery to zero, phone was unable to boot to charging mode, so I booted from another battery, and with a wall charger plugged in, I replaced battery with empty one. Then question mark sign appeared when there was no battery, but I don't remember how I got rid of it. Maybe it disappeared after some time? I don't know. But for sure it disappeared.
sssloba said:
I tried both of this things, and none of them worked. When powered on, without charger, on the battery icon stands [!]
and when it is connected with a wall charger, icon changes to little lightning ( standard charging icon) inside the empty battery, without movements (battery do not changes colors, red, yellow, green). On lock screen says: Charging 1%, and same on the battery settings (1%).
That was on costum rom.
And on the stock rom in the battery icon stands [?], and when I connect it to the wall charger it says (with original Motorola battery inside):
"Invalid battery
Your device battery is invalid and cannot be charged.
Replace the battery with an original Motrola battery."
I changed the cable, and the charger, but I do not have third battery...short circuit...maybe...maybe.
One interesting fact, the battery seems to be charging, although it says 1%.
The original battery was empty at the begining, she couldn't even start the phone, and now phone is working on that battery....strange. Should it be able to do that, if there was a short circuit?
Click to expand...
Click to collapse
Battery sign with a "?" shows when battery is completely uncharged (and before the master clear in my case). Power off the phone, install the bypass cable (again) and put it in the wall charger with phone powered off. Wait 15 minutes charging before power on and wait more 15 minutes charging. Now remove the bypass cable and let battery charge as usual before powering on again.
I did all of that. I downloaded some battery widget, and it shows the battery state 100%. Same is when i go to Settings=About phone=Phone status, battery status is charged 100%. Now the only thing is that in the original battery status icon is still [?].
The important thing is that battery is 100% full and phone is not broken, it works! !
@rabinhood
I flashed costum and stock rom.
I have replacement battery, and same thing happens on it. Also I tried changing them while charging...nothing.
Maybe it will disappear by itself if I wait long enough. :laugh:
So, here's my situation, my phone suddenly turned off last night while installing a game, when i tried to power it up, it "blinking" on the boot logo, it keeps turned on and off, so i reckon its battery has run out, so i charge it, then it works, it can boot to system, after it shows around 80% i unplugged the charger but the phone then suddenly turned off and again, blinking on the boot logo.. so i charge it again just to see it boot to system and shows 80% battery.. i tried to charge it to 100%, but at 100%, the phone suddenly died, again..
at first i thought it might be a battery problem, or power circuit thingy, but here's the catch, it can hold for 30 mins + on bootloader mode..
can someone tell me what is wrong with my phone?
EDIT: flashed stock ROM and Recovery, still no use
EDIT2: Did the QPST as suggested as Rwepradeep, still blinking on lenovo logo
EDIT3: Solved! Battery was the actual problem
chlova said:
So, here's my situation, my phone suddenly turned off last night while installing a game, when i tried to power it up, it "blinking" on the boot logo, it keeps turned on and off, so i reckon its battery has run out, so i charge it, then it works, it can boot to system, after it shows around 80% i unplugged the charger but the phone then suddenly turned off and again, blinking on the boot logo.. so i charge it again just to see it boot to system and shows 80% battery.. i tried to charge it to 100%, but at 100%, the phone suddenly died, again..
at first i thought it might be a battery problem, or power circuit thingy, but here's the catch, it can hold for 30 mins + on bootloader mode..
can someone tell me what is wrong with my phone?
Click to expand...
Click to collapse
Flash Stock ROM or any Other ROM and report back
Rub My Donger :'v said:
Flash Stock ROM or any Other ROM and report back
Click to expand...
Click to collapse
downloading the stock ROM atm, will report once it's done
Rub My Donger :'v said:
Flash Stock ROM or any Other ROM and report back
Click to expand...
Click to collapse
flashed Stock ROM, still happening
chlova said:
flashed Stock ROM, still happening
Click to expand...
Click to collapse
in what way u are flashing the stock rom??
try flashing with QPST if u had pc..
then ur phone will start like a factory product..
if u have pc search in YouTube for qpst method..
that method can solve
Rwepradeep said:
in what way u are flashing the stock rom??
try flashing with QPST if u had pc..
then ur phone will start like a factory product..
if u have pc search in YouTube for qpst method..
that method can solve
Click to expand...
Click to collapse
okay so i did the qpst thing, it can hold on at download mode until it finished, then after that the phone reboots, and it happened again...
i don't get this phone, it works well on bootloader and download mode, but not so long at recovery.. not to mention i can't even boot into system (can't even past the boot logo lol)
Okay so, i took it to Lenovo Service Center, they told me something wrong with the battery, apparently it hold up on bootloader because the bootloader mode didn't took so much power, so even a broken battery should hold up a little.. Changed the battery, now it works well, thanks for all the help..
Hi, my Le pro 3 (x727) is stuck on the boot screen. It shows the leeco boot screen then vibrates twice and then shuts off and repeat the process. My phone was unrooted and completely stock. Is it bricked? should I try to unbrick using the methods on this forum?
sau41 said:
Hi, my Le pro 3 (x727) is stuck on the boot screen. It shows the leeco boot screen then vibrates twice and then shuts off and repeat the process. My phone was unrooted and completely stock. Is it bricked? should I try to unbrick using the methods on this forum?
Click to expand...
Click to collapse
Okay can you provide more info
You say that it has never been rooted and never on a custom rom?
How long did you have the phone?
Were you using the stock charger and cable?
If its just a Brick
You can follow my instructions to unbrick.
https://forum.xda-developers.com/le-pro3/how-to/unbrick-leeco-phones-leeco-variants-t3847220
Read several times and properly install the software and drivers on your PC,. ( I cannot stress enough that you read the instructions of the OP and the first post underneath) If your phone is bricked those instructions will repair it.
If its hardware
Unfortunately, your issue could be a bad battery. Which is no big deal they only cost $8
If you have always used stock, and the issue is hardware its probably just the battery alone and nothing worse.
If it is something worse, it could be the usb card which is $13, I doubt that you would have a more serious issue such as a fried motherboard.
Good Luck
Let me know how it goes, on the unbricking thread.
tsongming said:
Okay can you provide more info
You say that it has never been rooted and never on a custom rom?
How long did you have the phone?
Were you using the stock charger and cable?
Click to expand...
Click to collapse
I had the phone on release date which was november 2016 i think. Yeah, I have never tried to root or install a custom rom. I am using an anker powerline+ since the original cable didnt last long, still using the original charger. I have tried both the cable and the charger on a Nintendo Switch and it seem to work fine.
I am currently downloading the files from your guide, the big one is taking too long though. Do you have any other link for
le_zl1_qfil_ufs_fix.zip?
Other observation/s:
The phone warms up when left on charge, no notification light though.
The phone's battery life was degrading which I thought was natural. Last time I check through Accubattery was at 84%.
Before the phone died, I checked the time through my phone which was 1:30 am and is less than 25% battery, woke up at 4:30 am and its dead. Phone was unplugged during that span.
sau41 said:
I had the phone on release date which was november 2016 i think. Yeah, I have never tried to root or install a custom rom. I am using an anker powerline+ since the original cable didnt last long, still using the original charger. I have tried both the cable and the charger on a Nintendo Switch and it seem to work fine.
I am currently downloading the files from your guide, the big one is taking too long though. Do you have any other link for
le_zl1_qfil_ufs_fix.zip?
Other observation/s:
The phone warms up when left on charge, no notification light though.
The phone's battery life was degrading which I thought was natural. Last time I check through Accubattery was at 84%.
Before the phone died, I checked the time through my phone which was 1:30 am and is less than 25% battery, woke up at 4:30 am and its dead. Phone was unplugged during that span.
Click to expand...
Click to collapse
It sound like the battery stats were off. Try leaving it plugged in overnight and then use this Qfil
le_zl1_qfil_ufs_fix.
https://androidfilehost.com/?fid=818070582850488404
tsongming said:
It sound like the battery stats were off. Try leaving it plugged in overnight and then use this Qfil
le_zl1_qfil_ufs_fix.
https://androidfilehost.com/?fid=818070582850488404
Click to expand...
Click to collapse
Thanks, but i got it back alive just this morning without flashing . I left it on repair mode (vol + - power) for a whole day to drain the battery. Then once I plugged it to the charger, it was running normally again. Is there any way to reset the battery stats?
sau41 said:
Thanks, but i got it back alive just this morning without flashing . I left it on repair mode (vol + - power) for a whole day to drain the battery. Then once I plugged it to the charger, it was running normally again. Is there any way to reset the battery stats?
Click to expand...
Click to collapse
That's great news! So apparently you had built up static discharge. In the past you could resolve this issue by simply taking the battery out and reseating it.
To clear battery stats
Boot to recovery , open file manager, go to data/system the down at the bottom you wiil find the batterystats.bin delete it and then reboot to system.
I do this about twice a month.
Take care, I am glad you got it working.
Sent from my LEX727 using XDA Labs
tsongming said:
That's great news! So apparently you had built up static discharge. In the past you could resolve this issue by simply taking the battery out and reseating it.
To clear battery stats
Boot to recovery , open file manager, go to data/system the down at the bottom you wiil find the batterystats.bin delete it and then reboot to system.
I do this about twice a month.
Take care, I am glad you got it working.
Sent from my LEX727 using XDA Labs
Click to expand...
Click to collapse
Im pretty new to this, but on recovery I can only see update and recover(format). I suppose I need a tool or something. I already downloaded flash2 and qfil, are those the tools that i need?
sau41 said:
Im pretty new to this, but on recovery I can only see update and recover(format). I suppose I need a tool or something. I already downloaded flash2 and qfil, are those the tools that i need?
Click to expand...
Click to collapse
I thought your phone was working?
You don't need those files unless you have a brick. Go to the TWRP website for learning about the functions of TWRP
Double post, read below.
tsongming said:
I thought your phone was working?
You don't need those files unless you have a brick. Go to the TWRP website for learning about the functions of TWRP
Click to expand...
Click to collapse
Yup it's working, I just need to reset the battery stats. Anyways, thank you so much. I'll head to TWRP and do some reading.
tsongming said:
I thought your phone was working?
You don't need those files unless you have a brick. Go to the TWRP website for learning about the functions of TWRP
Click to expand...
Click to collapse
Hey, sorry to bug you again but my phone went back to bootloop. I tried draining the battery again but this time it didnt work. I went on and flash qfil and was successful at it. The problems is, right after flasing qfil, I rebooted the phone by long pressing the power button, but it just goes back to bootloop at the leeco logo. What could be wrong?
sau41 said:
Hey, sorry to bug you again but my phone went back to bootloop. I tried draining the battery again but this time it didnt work. I went on and flash qfil and was successful at it. The problems is, right after flasing qfil, I rebooted the phone by long pressing the power button, but it just goes back to bootloop at the leeco logo. What could be wrong?
Click to expand...
Click to collapse
I made a whole thread for these kinds difficult issues. Read the OP and my posts #2 and #3 on that thread.
https://forum.xda-developers.com/le-pro3/how-to/unbrick-leeco-phones-leeco-variants-t3847220
If all else fails, you can mail the phone to me to attempt doing it for you. Read the thread.