Related
Appologies for duplicating this post here and on the accessories forum but needed a quick answer!
Anyone technically minded who can answer this....
I am using a HTC Touch Pro mains charger for my X1 (as it has a longer cable) which charges the X1 fully.
I did notice the back of the X1 getting a little warm, so double checked the outputs on the original X1 charger and the TouchPro one.
X1 = 5v 700mA
TouchPro = 5v 1A
Is this likely to be a problem?
You should definately not mix power adapters like that. On the other hand they both use mini-USB plugs so if they follow the USB standard (Battery Charging Specification) you are okay. The spec allows for up to 1,8 A, but that does not mean the X1 can take it.
I would have rather bought an extension cable for the X1 charger. Then you are safe _if_ anything happens and you damage your X1. :|
If you need a longer cable, just plug in a standard USB extension cable It will work perfectly and you can extend to plenty of meters if you need to.
Regarding the use of the 1A charger, I don't think it will be that much of a problem, but I wouldn't count on it to cause no problems either. The battery getting warm is not that odd when charging, as batteries generally generate heat when they get charged. The fact that it gets warmer with the 1A, instead of the 0.7A charger, is just because you charge the battery quicker, which in turn causes more heat. You should keep it mind though that heat is a bad thing for LiIon batteries like the X1 uses. Having it being warm reduces lifetime quicker then when it's cool.
maedox said:
You should definately not mix power adapters like that. On the other hand they both use mini-USB plugs so if they follow the USB standard (Battery Charging Specification) you are okay. The spec allows for up to 1,8 A, but that does not mean the X1 can take it.
I would have rather bought an extension cable for the X1 charger. Then you are safe _if_ anything happens and you damage your X1. :|
Click to expand...
Click to collapse
Thanks for your help. I assumed - like you - that USB was USB in regards to power output. But I will take your advice and get an extension and stop using the old one.
Cheers
.
What I've seen on battery charging on mobile phones is that they have an internal intelligent charging system, at least the Siemens and Wavecom systems I've been using.
LiIon batteries are normally charged using constant voltage/constant current until a certain voltage level is reached, ~4.2V for 3.6V batteries. Then the charge current is reduced with a constant voltage until the charging current reaches zero. This implies that from a 5V charger there has to be some sort of internal charging system to make it work.
If you get a charger for USB it is the internal system that handles the current rate, not the charger. The specs on the charger shows the maximum current possible, not the charger's constant charge rate.
So if the phone's internal charging system thinks it's ok with 1A it will use it, but as mentioned earlier, it will produce more heat, but with a faster charging.
Though USB charging specs is limited to 1.8A, most charging circuits is possible to set to less current, with some part charging the battery, the rest powering the phone.
on8a said:
What I've seen on battery charging on mobile phones is that they have an internal intelligent charging system, at least the Siemens and Wavecom systems I've been using.
LiIon batteries are normally charged using constant voltage/constant current until a certain voltage level is reached, ~4.2V for 3.6V batteries. Then the charge current is reduced with a constant voltage until the charging current reaches zero. This implies that from a 5V charger there has to be some sort of internal charging system to make it work.
If you get a charger for USB it is the internal system that handles the current rate, not the charger. The specs on the charger shows the maximum current possible, not the charger's constant charge rate.
So if the phone's internal charging system thinks it's ok with 1A it will use it, but as mentioned earlier, it will produce more heat, but with a faster charging.
Though USB charging specs is limited to 1.8A, most charging circuits is possible to set to less current, with some part charging the battery, the rest powering the phone.
Click to expand...
Click to collapse
Thanks very much that's very informative.
I am wondering if the X1 has this internal intelligent charging system you mentioned. Would be useful to know.
Actually the mA ratings are what the charger can deliver. Not what they actually will deliver. A 700mA rated charger will supply up to 700mA if asked for by the device. This is a two way thing. The charger side will never provide more than it's maximum rating, it's a built in safety thing. The charged side should never ask for more than it can handle, providing that it is a well built piece of electronics. I trust the X1 to be well built on this. USB standards rate a maximum of 500mA for high power devices. The X1 does adapt and thus will charge slower.
Glad this is being discussed; as my X1 is a UK model, I don't have a US wall charger.
I found some on monoprice.com, see under the Power to USB section at the bottom:
http://www.monoprice.com/products/subdepartment.asp?c_id=103&cp_id=10311
They have 3 varieties:
High-Speed WALL Power to USB Female Converter (1000mah) - Black
High-Speed WALL Power to USB Female Converter (1000mah) - White
[**cant tell a discernable difference between those two, but one is larger...**]
WALL Power to USB Female CHARGER Converter - Black (500mah)
[**many people complaining about this not charging their devices; either it really does suck or they didnt get one with enough output**]
I WONT kill the phone picking up a 1000mah?
Anyone else in my situation needing a new US charger, this site has great prices on this stuff... these adapters are under 2 bucks, and USB cables are super-cheap too!
I recently bought new tab, it is getting charged normally when plugged in power socket. But when i plug it in laptop USB port or any PC port, it would not charge instead I can transfer data etc. I am using the original USB cable which came in box. Does any one has faced same issue?
Sent from my GT-P1000 using XDA App
charging
Samsung have engineered it so you have to even use their mains charger. Car chargers and wall chargers have to be Samsung tab brand. Not sure but there is talk of AVUSB charge cable being released. Pretty sure this has already been covered.
Turn off the screen and wifi and data network and it will charge very slowly over usb.
Sent from my SGH-T849 using XDA App
The fact of the matter is the tablet requires more/not the right amount of power that your USB port can deliver.
We always here all these theories about why.. but here is the simple and only reason why.
To keep the techinical stuff short and simple, Li-Poly and other batteries have a predetermined lifetime and one of the determining factors to how long they last is the rate of charge (charge rate) time and the exact amount of mHa capacity of the battery.
This is NOT a Samsung marketing scheme as it is exactly the same reason the iPad cannot be charged through USB.
I'll give you a quick example:
If you buy rechargable batteries, Ni-Mh that state they can be charged at 2500mHa (capacity/rate) and you charge them on a 15 minute charger that delivers the right amount of power (1.2 volts) and not the correct rate (lets say they are rated for 2500 and you use a charger thats rated for more) this causes the battery life to be deminished drasitcally.
If you charge the same 2500mha batteries with a lower rating charger, they will take a lot longer to charge completely since it is at a slow mHa, but also this slower charging will provide a longer battery life.
Therefore their charger (and this is the reason why you must use their charger or any charger with the same mHa rating) is made to provide the optimal amount of charge rate (mHa) giving you the best battery life vs charge time.
In conclusion the Tabs hardware will limit the rate of charge through USB in order to:
a) Not overload the power on your USB, given that all this varies according to each system configuration (although it should not! but reality is.. it does)
and
b) In order to not improperly charge your tab, reducing your battery life.
I know the technical parts are vaguely/poorly explained but I work with Li-Po and other types so this is the simplest way to explain all this without causing too much confusion.
Hope this made sense
Cheers
tj1984 said:
Samsung have engineered it so you have to even use their mains charger. Car chargers and wall chargers have to be Samsung tab brand. Not sure but there is talk of AVUSB charge cable being released. Pretty sure this has already been covered.
Click to expand...
Click to collapse
Not true.
Samsung is using standard chargers that are wired to identify themselves as high current chargers. A non Samsung charger / external battery will likely have the same wiring because this wiring is part of the usb-specification.
The Tab will even charge from your usb-port but only slowly and if you turn off the screen since usb-ports only have 500mA (the charger has 2A).
So all the Tab does is check for this high-power-wiring. If it detects it it shows you the charge-icon, if it doesn't it assumes a usb-connection to your computer and does not pretend to charge (even if it does).
Interesting! So then a generic car cig lighter accessory with a standard USB port on it should charge it as a high output conection, right?
I am able to charge my Tab using usb connection to my PC by turning the device off. Same with an Energizer XP8000 external battery. Leaving the device on will take a long time to charge or not at all if you are using it while charging.
Hi all,
Ok, so I finally managed to order a 16Gb Nexus 4 and hopefully it will be with me in 1 week or so.
And I was wondering one thing regarding the AC adapter: I believe (pls correct me if I am wrong) that the original AC adapter’s output voltage is DC 5V, 1.2A.
I will need an extra AC adapter to keep it at work and I was planning to use one of those:
- The Sony Xperia P AC adapter will output 5V, 1,5A
- The Samsung Galaxy S AC adapter will output 5V, 0,7A
It is clear that neither of those 2 chargers will match exactly the specifications of the original Nexus charger (same voltage, but different amperage).
So, here goes the questions:
1) Is there any problem if I use a charger that will output the same voltage but with different amperage?... if not, which one would you use and why?.
2) how the amperage affect to the charging process?.
Thanks all in advance
PS: sorry for terrible English
You can use any charger up to 2 amps.
Sent from my Nexus 4 using xda app-developers app
Evergreen74 said:
Hi all,
Ok, so I finally managed to order a 16Gb Nexus 4 and hopefully it will be with me in 1 week or so.
And I was wondering one thing regarding the AC adapter: I believe (pls correct me if I am wrong) that the original AC adapter’s output voltage is DC 5V, 1.2A.
I will need an extra AC adapter to keep it at work and I was planning to use one of those:
- The Sony Xperia P AC adapter will output 5V, 1,5A
- The Samsung Galaxy S AC adapter will output 5V, 0,7A
It is clear that neither of those 2 chargers will match exactly the specifications of the original Nexus charger (same voltage, but different amperage).
So, here goes the questions:
1) Is there any problem if I use a charger that will output the same voltage but with different amperage?... if not, which one would you use and why?.
2) how the amperage affect to the charging process?.
Thanks all in advance
PS: sorry for terrible English
Click to expand...
Click to collapse
You must use a 5V AC USB Adapter and better no LESS than 1A
for Fast Charge.
AC Adapter I Use:
iPad AC Adapter 5V 2.1A at Work
PlayBook AC Adapter 5V 1.8A at Home 1
Original Nexus 4 AC 5V 1.2A at Home 2.
Our Nexus 4 will Draw around 0.8A when Batt lever at 0% - 80%,
then around 0.5A at 80%-95%, Final State 95%-100% will draw 0.2A roughly.
When 100%, Nexus 4 will use the AC power & the Current "A" show on phone
will like 2mA (0.002A) when idling.
** 1A = 1000mA
As previous poster said, do not go under 1.2amp.
I run the OEM charger in my bed room, a USB charger to my computer, and a 2.1amp charger in the car.
Sfkn2 said:
As previous poster said, do not go under 1.2amp.
I run the OEM charger in my bed room, a USB charger to my computer, and a 2.1amp charger in the car.
Click to expand...
Click to collapse
Why do you say not to go under 1.2A? Charging from a laptop is at .5A. I've been using a 1A charger since day one. Haven't experienced any issues with it.
Charging at a lower amperage shouldn't hurt anything, just charge slower. All you have to do is make sure it's a 5V charger. Amperage shouldn't matter but a lower amp charger will charge slower. As for a higher amp charger, the phone will only draw the amount of power it needs to charge so using 2A charger won't hurt anything either.
Also 2mA is 0.002A not 0.02 A
wilsonlam97 said:
You can use any charger up to 2 amps.
Sent from my Nexus 4 using xda app-developers app
Click to expand...
Click to collapse
Since the charger doesn't actually regulate the charging itself (the phone does this) it doesn't matter how many amps it can supply, could be 100 amps, no worries. As long as it is 5V, the phone will draw as many amps as it needs.
Since the supplied charger is 1.2A rated, it's fair to assume that the phone will never actually try to draw any more than that, so there will be no benefit in going higher.
Going for a lower current charger will likely extend the charge time.
I use a 2.1 amp daily without any issues.
Sent from my Nexus 4 using Tapatalk 2
Wow guys!!... thanks all for your answers!!
So, if I understood correctly, the amperage will only affect to the charging time, meaning that by using the Xperia P AC adapter (1,5A) the battery will be charged faster that using the Galaxy S one (0,7A)... right?
Pls allow one last question: a few yeard ago, I think I read in some forums that a slower charging process could help to keep the batteries in the best conditions for a longer time... is this still true with modern batteries??
Again, THANKS all for your help!!
Evergreen74 said:
Wow guys!!... thanks all for your answers!!
So, if I understood correctly, the amperage will only affect to the charging time, meaning that by using the Xperia P AC adapter (1,5A) the battery will be charged faster that using the Galaxy S one (0,7A)... right?
Pls allow one last question: a few yeard ago, I think I read in some forums that a slower charging process could help to keep the batteries in the best conditions for a longer time... is this still true with modern batteries??
Again, THANKS all for your help!!
Click to expand...
Click to collapse
Yes, the .7A charger will take a little longer to charge you phone.
On the other answer, I think NO but I'm not as familiar with LiPo batteries. I would venture to say that .7A vs 1.2A (max the phone will draw but I think someone above mentioned it's even less than that when the battery is very low) is not going to make a bit of difference in your battery life.
One thing I do know about LiPo's is you do not trickle charge them. So while plugged in it will charge at the rates mentioned above until full and then it QUITS charging all together. Once the phone discharges the battery to a certain level, it will charge it back up again. Probably at 98-99%.
There may be one other thing to consider when selecting a third party charger. In the Nexus 7, the device looks for pins 2 & 3 (data) of the USB plug to be shorted in order for it to draw full current. If this pins are open (or have a load across them as is the case with iPhone/iPad chargers), the Nexus 7 will assume it is plugged into a computer and limit its draw to 500MA.
Not certain the Nexus 4 behaves the same way but would assume so.
setzer715 said:
Yes, the .7A charger will take a little longer to charge you phone.
On the other answer, I think NO but I'm not as familiar with LiPo batteries. I would venture to say that .7A vs 1.2A (max the phone will draw but I think someone above mentioned it's even less than that when the battery is very low) is not going to make a bit of difference in your battery life.
One thing I do know about LiPo's is you do not trickle charge them. So while plugged in it will charge at the rates mentioned above until full and then it QUITS charging all together. Once the phone discharges the battery to a certain level, it will charge it back up again. Probably at 98-99%.
Click to expand...
Click to collapse
setzer715, thanks for the answer... I think I will be using the Xperia P charger at work...
Thanks all for your help!!
I want to make this case clear. According to my Charging log,
Here is some key point.
Nexus 4 Max Draw Rate at Fast Charge Mode is around 800-900mA,
even you use a Charger that rated at 1A (iPhone Tofu), 1.2A (Original),
1.8A (Playbook), 2.1A (iPad).
Fast Charge Mode must be with Charging Cable with 2&3 pin Shorted,
or the charger itself have the 2&3 pin already shorted.
Therefore, 1A is a Sweet spot for getting Charger & Charging Time for
Li-Po/Li-Ion/Ni-MH Batt charging.
If you use under 1A Charger, eg 700mA or 500mA, it will take much longer
to charge the batt but no harm as well. Just too slow only.
The stock charger that came with my phone sucks, I use one from my epic 4g touch (gs2)and it charges much better
DEVICE: Nexus 4
KERNEL: Franco r95
ROM: PROJECT Extinct Life Event
jlear3 said:
The stock charger that came with my phone sucks,
Click to expand...
Click to collapse
Why you say so...? What's wrong with it...?
Talon88 said:
Why you say so...? What's wrong with it...?
Click to expand...
Click to collapse
Left a phone on a charger all night with a long (10ft) cable and it couldn't even charge the phone over night. I know a 10ft cable will slow things down but my gs2 plug has no problem charging my phone. Search around and you'll find a few fail stories about the stock LG charger.
Sent from my Nexus 4 using Tapatalk 2
So we just upgraded to Note 3 from our galaxy 3 (wife and I)...
I noticed the charger is a 2 amp charger compared to the SGS 3's 1 amp.
I started reading some threads here and found out the USB 3.0 cable will not charge the phone faster unless it's plugged into the computer.
Apparently the PCM also limits the phone to charging at 900ma. (not verified)
so I'm curious now.... at what amps does this phone charge? I'm trying to get a spare charger to keep in the car, and also trying to get a usb car charger if I can benefit from the 2.1 amp one instead of the 1 amp one that's in there now....
Can anyone tell me if I should get a 2.1amp charger or stick with 1 amp chargers as the spares if it'll still charge at 900ma?
I'm using USB 2.0 cables btw. (unless I can charge faster with the USB 3.0 when plugged to a car charger or the wall, which I apparently won't from my research here)
While I await for responses, I will plug the charger into my voltage/amp reader and we'll see how much power is being drawn, which might give an idea as to how many ma it's charging at.
For whoever that wants to know this information, these are my findings from my meter that is able to measure how much power is being drawn (kill a watt P3)
with the stock charger and USB 2.0 cable (3.0 made no difference) the phone will charge at 900ma with the screen on. If the phone is shut off, or screen is off, it goes to 1500ma. Very steady at those.
with the SGS3 charger that I had, it's a constant 900ma whether screen is on or off... (1.0 amp charger)
now I guess I will have to see if this is the case with any 2.1 amp charger, or if it's specific to samsung's charger with snapdragon's quick charge feature. I believe only certain chargers allow use of this.
I don't know, I'm getting 1800mA by using stock wall charger with USB3 cable and 450 with USB2 cable. I know GS3 would charge at faster rate when using original Samsung wall charger and cable, which had data lines shorted, not sure if it's the same with Note3.
I don't remember for sure, but I think charging rate from computer was pretty much the same 450mA regardless of USB3 or USB2 port or cable. I remember this because I was surprised they didn't take advantage of higher power ratings with USB3, but maybe it was just my particular setup. I used application that shows charging rate, so all is with phone on, but it makes perfect sense, about 2 hours from 0 to 100% charge, if you allow some extra time for trickle charge at the end, losses and usage.
pete4k said:
I don't know, I'm getting 1800mA by using stock wall charger with USB3 cable and 450 with USB2 cable. I know GS3 would charge at faster rate when using original Samsung wall charger and cable, which had data lines shorted, not sure if it's the same with Note3.
I don't remember for sure, but I think charging rate from computer was pretty much the same 450mA regardless of USB3 or USB2 port or cable. I remember this because I was surprised they didn't take advantage of higher power ratings with USB3, but maybe it was just my particular setup. I used application that shows charging rate, so all is with phone on, but it makes perfect sense, about 2 hours from 0 to 100% charge, if you allow some extra time for trickle charge at the end, losses and usage.
Click to expand...
Click to collapse
and how did you measure this 1800mA?
razorseal said:
and how did you measure this 1800mA?
program is called galaxy charging current, you can get it in the play store.
Click to expand...
Click to collapse
You can't compare that app to a meter that shows you the actual current being drawn
Sent from my SAMSUNG-SM-N900A using Tapatalk
why not? How do you think your meter is working? Phone has similar IC. How did you come up with your numbers first of all? I thought you plug Kill a watt into outlet and it shows what the charger is using at 110v and at about 10 watts(or is it 220-240v for your location), your unit maybe at the limit of accuracy, since the amperage would be somewhere around 100mA, where your device is designed more for larger power consumption like fridge or TV running 300-1000watts and few amps. Is your unit somehow capable of measuring what the charger is outputting and if so, how?
BTW you can't get more than 900mA from PC even over USB3, thats the max limit.
I checked again: galaxy S3 wall charger is giving me 600mA, Note3 charger with USB2 cable gives me 1200mA and Note 3 charger with USB3 cable pumps out 1800mA, computer USB gives 450mA regardless of computer port, but there is something wrong with the USB3 cable that I got, is not connecting properly and I have to wiggle it to connect so maybe bad cable is the reason I don't get higher charge rate from PC USB3.
Any one Disappointed with the charger they included with the Pure. The non removable cord just sucks and a poor choice in my opinion
I'm more disappointed at the size of the wall wart. They could have made more friendly to other power strip users.
razor237 said:
Any one Disappointed with the charger they included with the Pure. The non removable cord just sucks and a poor choice in my opinion
Click to expand...
Click to collapse
Pretty sure they did that so you couldn't just stick any usb charging cord in their...it'd most likely fry it.
The disappointing part is the my other cords not working with Android auto. Luckily I have a nexus 6, and the cord with its charger works.
Sent from my P01MA using Tapatalk
brholt6 said:
Pretty sure they did that so you couldn't just stick any usb charging cord in their...it'd most likely fry it.
Click to expand...
Click to collapse
I guess that could be a reason but highly doubt anything would be fried. Ive been using a nexus 6 turbo charger and before that i was using a note 4 charger to charge multiple android/apple devices without issue. This just limits what i can charge on a single charger now need a second lol
razor237 said:
I guess that could be a reason but highly doubt anything would be fried. Ive been using a nexus 6 turbo charger and before that i was using a note 4 charger to charge multiple android/apple devices without issue. This just limits what i can charge on a single charger now need a second lol
Click to expand...
Click to collapse
If you plugged in a charging cord that can't handle the increased power it sure could fry the cord. I feel ya though...it would be nice if it were a USB cord.
I'm glad it looks different.... My son knows NOT to plug his HTC M7 into this charger.
I can see if this was someones first Android, the lack of a micro-USB for data would be frustrating, but I have about 5 of these in my desk drawer and throughout my house and office, so it doesn't bother me.
Also having a fixed cord means you don't pulg some 'slow' cable in and not get any benefits. Out my 8-10 micro USB cables, only 2-3 get a decent charge speed.
tele_jas said:
I'm glad it looks different.... My son knows NOT to plug his HTC M7 into this charger.
I can see if this was someones first Android, the lack of a micro-USB for data would be frustrating, but I have about 5 of these in my desk drawer and throughout my house and office, so it doesn't bother me.
Click to expand...
Click to collapse
If a device that does not do Turbo Charging is connected, the charger should automatically adjust and charge it at regular speed. At least, that's what it is supposed to do. The Turbo Charger is supposed to be the single charger for all types.
Sent from my Nexus 10 using Tapatalk
Darnell_Chat_TN said:
If a device that does not do Turbo Charging is connected, the charger should automatically adjust and charge it at regular speed. At least, that's what it is supposed to do. The Turbo Charger is supposed to be the single charger for all types.
Sent from my Nexus 10 using Tapatalk
Click to expand...
Click to collapse
Good, because I know I'll find his phone on that charger some day
I still have my galaxy s6 nexus charger that is a fast charging and it seems to work fine with turbo charging
Sent from my LG-H345 using XDA Free mobile app
I think the reason they made the cable fixed is because a lot of cheaper usb cables use very thin wire gauges. Since this charger puts out a lot of current at varying voltages, it's very possible for a thin cable to overheat easier and catch on fire. And my guess is, they didn't want to take any chances
How do we determine if turbo charger is ongoing? I mean are there any indication? Coz when I plug in the TurboCharger that comes with it, sometimes TurboPower Connected shows at the bottom of the screen, sometimes not. Then when I check it on the Status, it says Charging over USB, not Charging over AC? Could be that my unit is defective? perhaps the charger? or the battery?
DrearierJester1 said:
How do we determine if turbo charger is ongoing? I mean are there any indication? Coz when I plug in the TurboCharger that comes with it, sometimes TurboPower Connected shows at the bottom of the screen, sometimes not. Then when I check it on the Status, it says Charging over USB, not Charging over AC? Could be that my unit is defective? perhaps the charger? or the battery?
Click to expand...
Click to collapse
I've got the same issue going on. My replacement from Amazon will be here Tuesday so I'll have time to mess with both and see if its the charger or what. Currently my turbocharging is hit or miss.
DrearierJester1 said:
How do we determine if turbo charger is ongoing? I mean are there any indication? Coz when I plug in the TurboCharger that comes with it, sometimes TurboPower Connected shows at the bottom of the screen, sometimes not. Then when I check it on the Status, it says Charging over USB, not Charging over AC? Could be that my unit is defective? perhaps the charger? or the battery?
Click to expand...
Click to collapse
I have this issue sometimes to. So if I need to know if im charging at turbo I use an app from the app store to see if states I'm turbo Charging or not. In the Charging screen it will say "normal or Turbo"
https://play.google.com/store/apps/details?id=com.gombosdev.ampere
DrearierJester1 said:
How do we determine if turbo charger is ongoing? I mean are there any indication? Coz when I plug in the TurboCharger that comes with it, sometimes TurboPower Connected shows at the bottom of the screen, sometimes not. Then when I check it on the Status, it says Charging over USB, not Charging over AC? Could be that my unit is defective? perhaps the charger? or the battery?
Click to expand...
Click to collapse
You can use a USB voltage/current indicator device to see it directly. I use one that displays voltage and current simultaneously, it cost about $10 on Amazon.
The Qualcomm QC 2.0 (which Motorola terms "TurboPower) spec is 5, 9, 12, and 20 volts, with up to 2 amps plus at each voltage. The QC 2.0 chargers I've tested including the Motorola charger included with the XT1575, range up to 9V and about 2+ A at 9V, with the higher voltage/amperage when battery is discharged to a lower SoC.. Haven't seen 12V or 20V, I think those only come into play when battery is discharged to nearly zero SoC.
Agree the reason the included charger has cable attached may be to ensure adequate wire gage. Too-thin wire will increase voltage drop across cable thus lengthening charge time in higher power modes. But the design here uses higher voltage to keep current down around the same 2A max current of USB 2.0 chargers, so cable heat will not be a problem with any old USB cable.
I will attest to the benefit of QC 2.0. I thought it was a useless gimmick until I started using it. It does effectively compensate for mediocre battery capacity.
My "Turbo Charging" icon displays properly, but doesn't charge very quickly if connected to a cheap extension cord.
Plugged into the wall, the charging Stull doesn't impress me that much
Sent from my XT1575 using Tapatalk
DrearierJester1 said:
How do we determine if turbo charger is ongoing? I mean are there any indication? Coz when I plug in the TurboCharger that comes with it, sometimes TurboPower Connected shows at the bottom of the screen, sometimes not. Then when I check it on the Status, it says Charging over USB, not Charging over AC? Could be that my unit is defective? perhaps the charger? or the battery?
Click to expand...
Click to collapse
It's defective. Call moto they will replace it for free. Just have to send copy of purchase receipt. Had the same issue.
The charge rate depends on how discharged the battery is when connected to charge.
More discharged (lower SoC, State of Charge) will drive a higher charge rate.
As to the difference between this Motorola TurboPower (aka Qualcomm Quick Charge 2.0), vs. other phones:
I've measured up to 1.4 amps at 5V nominal on other phones, that is about 9 watts charging power. That is max charge rate, with a very discharged battery. As the battery charges up closer to fully charged, the charge rate (power) is reduced. Total charging time from fully discharged to fully charged would be about 4-5 hours, give or take, for a typical cellphone battery.
For comparison, the QC 2.0 measurements I made with the MXPE: Up to 2.2 amps at 9V nominal with a phone battery discharged to about 40-50%. That works out to about 20 watts charging power. As with other Li-Ion battery charging systems, this also declines as the battery approaches fully charged. Total time to charge, from fully discharged to fully charged will be about 2-3 hours, give or take.
So the marketing claims about QC 2.0 are about right: A 75% improvement over conventional charging systems.
The biggest gains come when charging batteries discharged to lower SoC. If you are comparing charge rate/time of batteries discharged to only, say, 70-80%, you will not see as much of a difference with QC 2.0.
I'm not a QC 2.0 marketing shill, mind you. I pretty much ignored it, before buying the phone. But for this phone, QC 2.0 actually does a good job to compensate for the mediocre battery. I can run the battery down to 40-50%, put it on QC 2.0 charger in my car for my 30 minute commute, and it is charged to around 80+% when I arrive at my destination. There are a lot of QC 2.0 certified aftermarket chargers out there too, Qualcomm did a lot of work on the front end as part of bringing it to market. (Just make sure any AC charger is UL listed or equivalent, if you care about safety.
Caveats on cables: The cable does make a difference at higher charge rates. Thinner gage wire will impose a greater voltage drop at higher current, this will reduce power and thus increase charge time.
Typical USB cables are AWG 26-28. You can buy 20, 22, and 24 AWG USB cables. Some cables advertise heavier (22-24) gage wire for the power leads with standard (26-28) gage wire for the data leads. The aftermarket QC 2.0 AC chargers I bought listed their included cables as 20 gage.
Get the heavier gage if you want full QC 2.0 charging.
soufdallas said:
I still have my galaxy s6 nexus charger that is a fast charging and it seems to work fine with turbo charging
Sent from my LG-H345 using XDA Free mobile app
Click to expand...
Click to collapse
Just to check did you use S6 original charger ? And does it charge same with the turbo power charger provided by moto?
Sent from my Moto X Pure (2015) via Tapatalk