Related
I need a little bit of help.
I've just started having a very annoying problem with my HD2. I does not shut down.
Each time I try to shut it down it just restarts.
If I have the battery taken out and I put it back in, the phone turns on automatically.
I tried various ROMs, reinstalled the HSPL, used Task29 various times and the problem it's still there.
And the most annoying is that when the battery reached the critical status (low %), the phones just enters a continuous loop of restarts until the battery is completely dry. Because I cannot turn it off the only solution is to take the battery out until I have the opportunity to charge the device
I don't know if it is a software or hardware problem. I think it should be software but still I do not have any clue on it.
Did anybody had this problem up to now? Any help would be more than welcome.
interesting problem. Most times if a problem persists across hard resets/ rom flashes with task 29, etc, then it is usually a hardware problem.
Have you tried calling your carrier or htc for tech support, maybe a new phone?
Solution?
Hi,
I also had this same problem. I solved it, strangely, by plugging the phone in to charge then unpugging and reseting. Hope this works for you too!
Scott
Unfortunately I cannot benefit from the warranty service or free replacement.
The repair costs would not be an issue. The only thing that bothers me is that I don't know if is a hardware or software related.
If I consider the symptoms it should be soft related. But if I consider the thing that nothing of the above mentioned worked, then I have to tag it as hardware issue.
The only thing that could trigger such a behaviour is the fact that this weekend I had it in some high temperature environment ... trying to hold the phone which was charging, in a car without AC, outside temperature 37 Celsius in the shadow, I almost burned my hand ... so maybe some strange protection was triggered.
Another strange behaviour it had, is that i could not charge it on various trials. With the charger connected, in car or at home, it would not charge and the signal led which on normal charge is amber, in these cases was blinking between amber and green.
if the phone gets too hot, it won't charge. That is a safety feature.
Make sure you check your battery contacts as well, where the battery sits in the phone. If the middle one is bent so it doesn't make contact with the phone, it can give you the flashing led.
I thought I read on here that the hd2's were warrantied by htc for 2 years, based off serial number. Wouldn't hurt to call and see.
But it sounds like something fried in the heat.
Thanks for the feedback. I'll try to see if I can have a service check on it.
danielterci said:
I need a little bit of help.
I've just started having a very annoying problem with my HD2. I does not shut down.
Each time I try to shut it down it just restarts.
If I have the battery taken out and I put it back in, the phone turns on automatically.
I tried various ROMs, reinstalled the HSPL, used Task29 various times and the problem it's still there.
And the most annoying is that when the battery reached the critical status (low %), the phones just enters a continuous loop of restarts until the battery is completely dry. Because I cannot turn it off the only solution is to take the battery out until I have the opportunity to charge the device
I don't know if it is a software or hardware problem. I think it should be software but still I do not have any clue on it.
Did anybody had this problem up to now? Any help would be more than welcome.
Click to expand...
Click to collapse
This issue has been discussed many times. A lot of people (including myself) has this problem. Try to put it into standby mode and after half a second, the screen comes back again. I have searched the forum many times, seems that no one has come up with a complete solution. Looks like it is not a hardware issue as most people found that if you connect it with your PC in activesync mode, it will resume normal.
My experience :
1. The problem just come up all of a sudden. Haven't install any software or apply any tweaks a couple of days before it happened.
2. Try to look into the active service via memmaid, nothing special.
3. Restore from previous backups when the machine hasn't got any problem. Didn't help.
4. Soft reset a couple of times. No use.
5. Hard reset finally. Problem still there.
6. Start to doubt that it is a hardware problem.
7. Use the plugin method. Normally after activesync, it resumes normal.
8. Also try to plugin micro USB without real connection. It sometimes works.
(I started to think that it might not be a hardware problem. It is obvious that when plugging in, something "stops".)
9. However, either way, it will happen again all of a sudden.
10. Start to take a few irrational moves : install BSB tweaks (haven't install since it sometimes crashes with Cookie's home). Switch to power saving mode with BSB.
11. Stop windows live autosync.
12. Install XDA shutdown. Whenever connected to PC via activesync, will manually put HD2 to sleep mode using XDA shutdown. Then unplug.
It has been four days now, everything resumes normal. The problem just gone all of a sudden. I really don't know what is the reason behind and which steps being taken is a solution. Anyway, that's my experience. Will update again for any changes again.
Ahkau said:
This issue has been discussed many times. A lot of people (including myself) has this problem. Try to put it into standby mode and after half a second, the screen comes back again. I have searched the forum many times, seems that no one has come up with a complete solution. Looks like it is not a hardware issue as most people found that if you connect it with your PC in activesync mode, it will resume normal.
My experience :
1. The problem just come up all of a sudden. Haven't install any software or apply any tweaks a couple of days before it happened.
2. Try to look into the active service via memmaid, nothing special.
3. Restore from previous backups when the machine hasn't got any problem. Didn't help.
4. Soft reset a couple of times. No use.
5. Hard reset finally. Problem still there.
6. Start to doubt that it is a hardware problem.
7. Use the plugin method. Normally after activesync, it resumes normal.
8. Also try to plugin micro USB without real connection. It sometimes works.
(I started to think that it might not be a hardware problem. It is obvious that when plugging in, something "stops".)
9. However, either way, it will happen again all of a sudden.
10. Start to take a few irrational moves : install BSB tweaks (haven't install since it sometimes crashes with Cookie's home). Switch to power saving mode with BSB.
11. Stop windows live autosync.
12. Install XDA shutdown. Whenever connected to PC via activesync, will manually put HD2 to sleep mode using XDA shutdown. Then unplug.
It has been four days now, everything resumes normal. The problem just gone all of a sudden. I really don't know what is the reason behind and which steps being taken is a solution. Anyway, that's my experience. Will update again for any changes again.
Click to expand...
Click to collapse
but if the problem persists across several roms and radios, how can it be software related? The fact that plugging it into the computer or charger sometimes fixes it, leads me to believe that it is the female usb connector that is the problem.
nrfitchett4 said:
but if the problem persists across several roms and radios, how can it be software related? The fact that plugging it into the computer or charger sometimes fixes it, leads me to believe that it is the female usb connector that is the problem.
Click to expand...
Click to collapse
You might be right. I really dun know if it is a hardware or software problem. But, it's kind of interesting that after u plugin it will work for quite some times. And, it will come back after the next soft reset.
OMG!! ... this means that I've just got the HD2 Ebola disease. )
Now being serious, after flashing 3 ROMs, hundred of soft resets, battery in out ... and one long night ...I just give up.
I will just try not to have the phone discharged. I hope there will be a solution sometimes soon.
Possible solution
I had the same problem.
I removed the cover, cleaned the two contacts on the back of the cover and for some unknown reason it returned to normal (although I was holding a pencil in a threatening manner to the red reset button).
What are these nodules for? I think more to do with reception, but it worked perfectly.
Hi everyone, I'm new to this forum (first post), I've owned my Continuum for a few months now happily with no problems. I actually love the phone! But recently I ran into a pretty big problem...
Let me give you a little background on my phone first, I have used SuperOneClick on it, to grant super user permissions, I've used the program to grant me access to the phone tethering apps that are out (currently using Open Garden), and the AdFree app in the market. I havn't used anything else in regards to 'hacking' my phone so I'm a bit confused as to why I'm getting trouble.
Anyways here's my problem, lol! Well the other day I turned off my phone and tried turning it back on and I would get a grey battery with the spinning disk, and it wouldn't turn on :\! I tried holding all the buttons, for over 10 seconds, no avail. It still turned on to the battery and nothing. I tried taking the battery out for a whiiiile and nothing. Eventually I plugged in my phone to the wall and it magically worked. Actually that's the only way I've been able to get my phone to turn on lately. It works fine once it's on but every time I turn it off the same thing happens .
So that's truly why I'm here... Is my phone 'bricked', or are these some symptoms of being 'bricked'? Are there any fixxes I can go about taking to you know...fix the problem ?
Any help would be Greatly appreciated,
Thanks everyone,
-Matt
Oops, I forgot to mention that my phone has been acting strange sometimes in the sense that I plug it into the wall and the 'Mass Storage/ Media player' option comes up, even though it's not plugged into the computer, just into the wall.
Pretty strange huh?
Anyways thanks again everyone who helps!!!
Can you try taking out the battery, then putting it back in...
Then hold down the volume down key as you power it back on?
I would try un-rooting and doing a factory reset... that should eliminate software issues... If you're still having issues then take it to VZW and let them give you a new one.
This is not "bricking"... If a phone is "bricked", it does nothing, absolutely nothing, and the only way to make it useful is to use it to build something.
Sure, right now it says "Downloading... Do not turn off Target!!!".
Thanks for letting me know it's not bricked, that's a little reassuring .
After a while I just took out the battery and stuck it back in and attempted to turn on the phone the usual way, and it turned on just fine. I'm guessing it's fixed and hopefully it won't do that again.
Hello all, I'm curious to hear your thoughts and advice.
My nook is completely unresponsive. It is not stuck at rooted forever.
In fact this has nothing with a root attempt/reset/restore/power on.
I had done a a fresh reset/root with touchnooter about four months ago and was happily and smoothly reading for about two months. I then got busy and put the nook down, did not touch or use for about another two months. I tried to use it about a week ago but found that it had run out of battery in sleep after the two months of disuse (not surprising). I put it on charge overnight and everything booted right and functioned well once it turned on, except that the battery indicator in the statusbar showed a "?" and the battery info in system info showed 100% "unknown". After alot of fruitless research I put it down with the intention of reset/restore/root when I had the time.
I just picked it up this morning and was faced with the expected "Press then button below to wake up your NOOK" screen. But when I pressed the "n" button nothing happened. Obviously holding the "n" did nothing as well.
I tried to power it off and on- nothing
holding power for 20- nothing
power for 30- nothing
8 failed boots- nothing
left right- nothing
left right power-nothing
random pushing and holding of power- nothing
all these with mem card in and out- nothing
all these plugged usb- nothing
all these pugged ac- nothing
I let it charge some more- nothing
None of the buttons do anything, the screen stays inevitably at the " press the n button to wake" screen. no activity whatsoever except that when It is plugged in, the green light shows. NO ORANGE LIGHT... it is fully charged by both usb and ac.
It is not detected at all by windows anywhere.
In Linux- lsusb, bklid, and df -h yield nothing. My nook might as well be the invisible stupid ereader.
I did not drop it, sumbmerge it, perform magic around it... It has been sitting on a shelf doing nothing.
To repeat, the only thing my nook does is light up green when plugged.
It is unchangeably stuck on poe's face...
If this isn't true brick, I don't know what is.
I'm exhausted. Any ideas? I appreciate the help.
Best,
Thomas
i don't know. i just know my dog ate mine and i'm now in the market for a new screen, so if you don't get it working sell me the unit and get some money for yourself to purchase a new one =D
or you could google the disassembly instructions and try unplugging the battery, not very hard to do. could be of .. some help perhaps?
I would definitely take you up on your offer, but i'm still under warranty.
However, I would still like to have my original, and figure out what is going on and why it happened.
Ideas?
Thank you.
similar problem were solved
Hi! I might have read about similar problem solved on USB host mode here http://forum.xda-developers.com/showpost.php?p=23475998&postcount=131
That's it, thanks so much.
if it help
if it helps let them know in the tread that you had same problem. they are wondering whether it is due to host mode
[N2E]: After automatic update to 1.1, Nook Touch Screen absolutely DEAD--Nothing Work
THIS WAS A POST FROM ANOTHER SITE AS TO MY PROBLEM:
I was reading on my N2E last night. I put it down for about 30 minutes and when I came back it was displaying the default "Authors" screensaver (I had switched to the Nature photos) and asking to slide to unlock. I thought, "Oh, the new software update must have downloaded and installed. I'll check it out." To my shock, the touch screen was completely unresponsive--no amount of swiping would unlock from the screen saver. I let it set for a while longer thinking perhaps the softare update was not yet finished. No such luck.
As a result of the new update, my NOOK is now completly DEAD! I tried powering off, but couldn't do that because you are asked to confirm power off on the touchscreen, which no longer works. So, I looked online and tried the soft reset/reboot by holding down the "Home" or "n" button and then pressing the power button for several seconds. Great--it started rebooting...and came right back to the "authors" screen saver and asking to swipe to unlock. I tried this rebooting process several times, always with the same result: back to screeensaver mode with completely unresponsive touchscreen.
So, looked at the online technical troubleshooting discussion and helps and decided to try a downloaded manual install of the software update. Plugged my NOOK into my computer and it recognized it. So, I downloaded the manualo software update and dragged and dropped it onto the NOOK as directed and sure enough, it started to reboot itself. I thought, "whew, maybe this will fix it". NOPE--came right back to the locked screensaver, with no mention of attempting to update software, and the touchscreen is still dead. (By the way, all of this was done initially with the NOOK showing about 94% charged, so it was not a battery issue.)
Reconnected the NOOK to my computer and the software update file was gone from its home directory, which implies it did something with it. So, I tried repeatedly to install the software update manually, always with the same result: NOOK comes back to locked default "authors" screensaver wtih a dead touchscreen.
Looked online for B&N technical support again saw that others had this problem (though only found a couple references). Found the instructions to do a factory reset and reluctantly tried that, desparate to make my NOOK work again, but frustrated that if it did I would have to rebuild everyting on it and download my 400+ B&N book library all over again. But, guess what, factory reset just comes up to the "Welcome to your all-new NOOK" screen (sounds like progress), BUT the touchscreen is STILL dead, so I can't hit the "Next" button onscreen to proceed with setting up my factory-reset NOOK. Tried rebooting again (as this seems to be the only solution offered in the online tech support) and now it just keeps coming back to the "Welcome to your all-new NOOK" screen with a dead touchscreen keeping me from doing anything.
So, now I am taking it back to my local B&N store in hopes they will exchange it for a new NOOK.
I really want to see a feature to disable automatic updates in the future. I specifically didn't download and manually install when the update came out, figuring I'd wait for the automatic download to give time to B&N to work out the bugs and perhaps issue a patch (as they have done in the past for the N1E). Instead I get no warning about the automatic download (happens while I am reading and set the NOOK aside for 30 minutes), and then the update KILLS my NOOK.
I am not a satisfied NOOK customer at this point.
MY POST: (from the that site)
Not Sure how to do this post or whatever, but I was happy until the update and everything that happened to you is the same with me. This is the first post that describes what happened to me. I'm out of warranty and refuse (and can't) to buy another one of these. If their updates can do this, I'm not sure I want to sink another $100 into the shareholders pockets. I'd really like to know if anyone knows what may be wrong with it.
In addition to what was already mentioned, I took the battery out several times(which seems intimidating but very easy but voids the warranty) and took it completely apart cleaning the screen very well with water and another time a glass cleaner. I tried rooting also. Not sure of what to do now. It seems software related due to working fine until the update. Still at the "Welcome to your all-new NOOK" screen with unresponsive screen. I wasn't sure if the last sentence from B&N was a personal message to me welcoming me to the "new" state of the my nook.
Thanks for any help from anyone.
Thanks.
Identical problem.... and no fix..
It is a shame you got no solution for this. and the worst, you are not the only one... it happened exactly the same with my Nook ST....
Hopeless...
Machiavelli_The_Man said:
THIS WAS A POST FROM ANOTHER SITE AS TO MY PROBLEM:
I was reading on my N2E last night. I put it down for about 30 minutes and when I came back it was displaying the default "Authors" screensaver (I had switched to the Nature photos) and asking to slide to unlock. I thought, "Oh, the new software update must have downloaded and installed. I'll check it out." To my shock, the touch screen was completely unresponsive--no amount of swiping would unlock from the screen saver. I let it set for a while longer thinking perhaps the softare update was not yet finished. No such luck.
As a result of the new update, my NOOK is now completly DEAD! I tried powering off, but couldn't do that because you are asked to confirm power off on the touchscreen, which no longer works. So, I looked online and tried the soft reset/reboot by holding down the "Home" or "n" button and then pressing the power button for several seconds. Great--it started rebooting...and came right back to the "authors" screen saver and asking to swipe to unlock. I tried this rebooting process several times, always with the same result: back to screeensaver mode with completely unresponsive touchscreen.
So, looked at the online technical troubleshooting discussion and helps and decided to try a downloaded manual install of the software update. Plugged my NOOK into my computer and it recognized it. So, I downloaded the manualo software update and dragged and dropped it onto the NOOK as directed and sure enough, it started to reboot itself. I thought, "whew, maybe this will fix it". NOPE--came right back to the locked screensaver, with no mention of attempting to update software, and the touchscreen is still dead. (By the way, all of this was done initially with the NOOK showing about 94% charged, so it was not a battery issue.)
Reconnected the NOOK to my computer and the software update file was gone from its home directory, which implies it did something with it. So, I tried repeatedly to install the software update manually, always with the same result: NOOK comes back to locked default "authors" screensaver wtih a dead touchscreen.
Looked online for B&N technical support again saw that others had this problem (though only found a couple references). Found the instructions to do a factory reset and reluctantly tried that, desparate to make my NOOK work again, but frustrated that if it did I would have to rebuild everyting on it and download my 400+ B&N book library all over again. But, guess what, factory reset just comes up to the "Welcome to your all-new NOOK" screen (sounds like progress), BUT the touchscreen is STILL dead, so I can't hit the "Next" button onscreen to proceed with setting up my factory-reset NOOK. Tried rebooting again (as this seems to be the only solution offered in the online tech support) and now it just keeps coming back to the "Welcome to your all-new NOOK" screen with a dead touchscreen keeping me from doing anything.
So, now I am taking it back to my local B&N store in hopes they will exchange it for a new NOOK.
I really want to see a feature to disable automatic updates in the future. I specifically didn't download and manually install when the update came out, figuring I'd wait for the automatic download to give time to B&N to work out the bugs and perhaps issue a patch (as they have done in the past for the N1E). Instead I get no warning about the automatic download (happens while I am reading and set the NOOK aside for 30 minutes), and then the update KILLS my NOOK.
I am not a satisfied NOOK customer at this point.
MY POST: (from the that site)
Not Sure how to do this post or whatever, but I was happy until the update and everything that happened to you is the same with me. This is the first post that describes what happened to me. I'm out of warranty and refuse (and can't) to buy another one of these. If their updates can do this, I'm not sure I want to sink another $100 into the shareholders pockets. I'd really like to know if anyone knows what may be wrong with it.
In addition to what was already mentioned, I took the battery out several times(which seems intimidating but very easy but voids the warranty) and took it completely apart cleaning the screen very well with water and another time a glass cleaner. I tried rooting also. Not sure of what to do now. It seems software related due to working fine until the update. Still at the "Welcome to your all-new NOOK" screen with unresponsive screen. I wasn't sure if the last sentence from B&N was a personal message to me welcoming me to the "new" state of the my nook.
Thanks for any help from anyone.
Thanks.
Click to expand...
Click to collapse
The factory restore does not actually fix every possible problem with your Nook.
If your Nook responds at all, try to boot it up on an SD card like ClockworkMod or noogie.
At least that way you can see what is happening.
The partitioning might have become corrupted which the "factory restore" does not touch.
If no response with anything, try disconnecting the battery.
You might also try booting over USB using the techniques in rooting the new white glow.
Hello I was wondering if I'm just screwed I bought 2 nook simple touch, one for me and one for a present to my mother for her birthday on march 16. I bought them at best buy for $40 a piece on January 30. I used mine and was perfect but when I tried to set up my mom it wouldn't load the license agreement, always got stuck or reboot or something, so I loaded cwm on an sd card just to play around, tested on my nook and was fine, then put it on my moms nook booted once then I didn't press anything and turn it off then I load the image but when I tried to boot again it got stuck on the load screen and wont do anything, no reset sequence will work with the sd card on or off the other nook boots with this sd card. at the end I exchanged with my mom she is happy with her nook an I have a useless unit do you think they will exchange it I didn't rooted it or did anything to it but has the n cwm splash on screen forever. I'm in Costa Rica right now and wont return home until May do you think I'll might be able to exchange it or should I just try to repair it.
I'm glad that your mother got the working one!
You say that that one will boot on your CWM SD card, but yours won't?
It may be hard to get your unit exchanged with a conspicuous screen on it, even if it's not your fault.
When you plug it into your desktop is there any indication of a new USB device found?
If it's charged and no amount of the power button gets a reaction, I'd open it up.
any news???
Hi endor43, same problem here, have been able to find any solution?
endor43 said:
Hello all, I'm curious to hear your thoughts and advice.
My nook is completely unresponsive. It is not stuck at rooted forever.
In fact this has nothing with a root attempt/reset/restore/power on.
I had done a a fresh reset/root with touchnooter about four months ago and was happily and smoothly reading for about two months. I then got busy and put the nook down, did not touch or use for about another two months. I tried to use it about a week ago but found that it had run out of battery in sleep after the two months of disuse (not surprising). I put it on charge overnight and everything booted right and functioned well once it turned on, except that the battery indicator in the statusbar showed a "?" and the battery info in system info showed 100% "unknown". After alot of fruitless research I put it down with the intention of reset/restore/root when I had the time.
I just picked it up this morning and was faced with the expected "Press then button below to wake up your NOOK" screen. But when I pressed the "n" button nothing happened. Obviously holding the "n" did nothing as well.
I tried to power it off and on- nothing
holding power for 20- nothing
power for 30- nothing
8 failed boots- nothing
left right- nothing
left right power-nothing
random pushing and holding of power- nothing
all these with mem card in and out- nothing
all these plugged usb- nothing
all these pugged ac- nothing
I let it charge some more- nothing
None of the buttons do anything, the screen stays inevitably at the " press the n button to wake" screen. no activity whatsoever except that when It is plugged in, the green light shows. NO ORANGE LIGHT... it is fully charged by both usb and ac.
It is not detected at all by windows anywhere.
In Linux- lsusb, bklid, and df -h yield nothing. My nook might as well be the invisible stupid ereader.
I did not drop it, sumbmerge it, perform magic around it... It has been sitting on a shelf doing nothing.
To repeat, the only thing my nook does is light up green when plugged.
It is unchangeably stuck on poe's face...
If this isn't true brick, I don't know what is.
I'm exhausted. Any ideas? I appreciate the help.
Best,
Thomas
Click to expand...
Click to collapse
There are times when a Nook gets in a mode where it won't accept a charge.
Opening it up and disconnecting the battery for a minute might fix this.
endor43 said:
That's it, thanks so much.
Click to expand...
Click to collapse
When this worked for you did the light turn orange right when you plugged the battery back in? I just took the battery out, plugged the nook into a charger, and with it plugged in plugged the battery back in and the light stays green the whole time yet I'm not able to use the nook at all.
My nook second generation is not responding to my touch I tried everything to get it to work and I eventually got it to completely power of what if it does not work when I turn it on what should I do
It could be power/battery problems.
Check to see if it makes itself known when the USB is plugged in.
If it reacts at all, that's an indication of life.
I was listening to an audiobook when my phone suddenly died. It would not start back up, so I removed the battery. When I replaced the battery, the samsung logo would pop up but after about a second it would go black again. It will not start again until I remove/replace the battery, at which point it does the one second shutdown again.
At one point I got the phone to boot (no idea what I did differently) and I noticed that it got very hot around the camera area before going black again. A second time I was able to get into recovery, where I did a factory reset. Booted back up and it seemed to be okay, but then heated up very quickly and shut down.
Now, even if the phone is totally cool, I cant get past that 1 second of samsung logo. I'm really at a loss here, and totally screwed without my phone because I am traveling non-stop for the next 2 weeks. Does anyone know how I might try to troubleshoot this? Thanks
Possibly flash a new ROM and start over. That's what I would do
This EXACT situation happened to me yesterday! I was streaming from Google music, it was on the charger and things were fine. A call came in and the phone started vibrating like crazy and wouldn't stop. The screen went black and it kept vibrating. Finally it went off. On boot it will get to my lock screen and then crash after about 30 seconds. If I take the battery out and try again it lasts another few seconds after boot. If I leave it for a LONG time with the battery out and restart it I can get like 2 mins on the next boot without it crashing. The top part by the camera is getting hot on my phone as well. Recovery mode and download mode start fine and the phone doesn't crash. I have some data on the internal that I want to save so I tried to use Odin to flash the most recent build L720VPUFNG2 as that would just install the OS and not touch the data. On the next reboot things seemed to be working fine and I got maybe 5 mins out of the phone before it crashed again. I still don't have enough time to get the data off so I think I'm just going to say screw it and wipe it completely. You guys know of a way I can backup this app data using Odin or recovery mode? My phone is currently unrooted. I'm new to all this tinkering stuff. Phone is out of warranty now anyway.
Threw on a custom recovery, backed up all my data, did a full wipe, now I am good as new.
It worked for awhile but now it is back to rebooting itself. Any idea what could be the issue? I'm assuming at this point it is hardware related. Why can recovery and download mode run consistently without crashing but when an os is fired up it has issues? If it was a hardware issue shouldn't it not work across the board?
So I had Sprint replace my phone on the 8th. I have been using my same batteries (1 stock 1 Anker) and chargers (some stock some not) without issue the past 5 days. I rooted and installed xposed and some modules (original broken phone was never rooted and was completely stock). Things were going great until tonight when it started reboot looping exactly like the old phone. I switched battery and same proble. After I took the battery out and left it out awhile it fired back up but I'm afraid the problem will return. Is it possible that the battery or charger randomly are causing damage to the phone? I only have 14 day warranty on this replacement and need to figure this out.
I have no idea maybe try just using your stock battery for a couple days. See how that goes then use your other battery for a couple days and see what happens.
i7vSa7vi7y said:
I have no idea maybe try just using your stock battery for a couple days. See how that goes then use your other battery for a couple days and see what happens.
Click to expand...
Click to collapse
I think it was one of the xposed modules causing the issue. I realized the rebooting seemed to happen whenever I pressed the power button. I had installed a power menu module so perhaps it was the cause. I restored from a nandroid and uninstalled that module and things seem to be working now. Hopefully that was the cause and this thing won't start acting up again after the return period.
killerz298 said:
I think it was one of the xposed modules causing the issue. I realized the rebooting seemed to happen whenever I pressed the power button. I had installed a power menu module so perhaps it was the cause. I restored from a nandroid and uninstalled that module and things seem to be working now. Hopefully that was the cause and this thing won't start acting up again after the return period.
Click to expand...
Click to collapse
That makes a lot of sense. Have to be careful with those Xposed modules. Don't get too carried away installing so many at one time and playing with them and then rebooting. You'll have a hard time figuring out which one is causing it. I'm pretty sure you found your problem.
i7vSa7vi7y said:
That makes a lot of sense. Have to be careful with those Xposed modules. Don't get too carried away installing so many at one time and playing with them and then rebooting. You'll have a hard time figuring out which one is causing it. I'm pretty sure you found your problem.
Click to expand...
Click to collapse
That is exactly what I did I installed like 6 at once and things were working well for a few hours then disaster stuck. I think I won't play with this phone anymore as I am upgrading anyway and want to sell it in working order.
So things were going well for awhile and then the reboot loops started up again. I did some digging and read that apparently Samsung phones are notorious for sticking power buttons and the symptoms were exactly what I was experiencing. I watched some videos online how to open the phone and clean out the power button but it didn't make a difference. I then read that squeezing the connector for the power button with a pair of pliers sometimes does the trick. Not for me. So finally since I'm not under warranty, have no insurance, and the phone wasn't working anyway, I just ripped the white plastic part of the power button right off. Well, that seemed to do the trick. Phone immediately fired back up without issue and has been going strong. I glued a small thin piece of plastic where the old one used to be and I am back in action. If my little plastic piece solution eventually fails or breaks off I will consider soldering on a new button but so far so good.
If you have tried everything else, and are looking for last resort, try cleaning the power button with some alcohol, and if that fails, rip off that power button! Here is the video that gave me the idea: https://www.youtube.com/watch?v=3Glllc7bEJs and here are some other power button videos: https://www.youtube.com/results?search_query=s4%20power%20button&search_type=&aq=f&oq=
Hi everybody,
What Happened:
My phone has suddenly become totally unresponsive. I have been using it most of the day, it was sitting at around 70% the time that it happened, but it is now a totally black screen. I had just taken it out of my pocket and it was suddenly like this.
The only idea I could come up with as to why this happened is that I charged it off of a JBL Charge 2 last night. I'm not sure if that may have messed with the battery, but I do find it odd that it's totally unresponsive while plugged in.
I was running android 7.1.1 DP2, with the ElementalX kernel 4.0 I believe. I was also rooted with SuperSU. What's really odd is that I hadn't done anything new recently besides install uTorrent and VLC media player. Otherwise, my routine has not changed one bit. Up to when the phone actually died, I hadn't even used either of these new apps the entire day.
What I've Tried:
I have tried plugging it in via AC, via USB, I've tried booting into recovery or fastboot, but there is zero response from the phone. No indicators on the screen, no LED blinks, no vibrations, nothing.
What I'll Try:
If anyone has any experience with this happening, I could use some advice. Otherwise I'm just going to wait it out, consider an RMA I guess. However, my device did have the bootloader unlocked and was rooted, so.... I hope it comes back by itself.
My advice is to keep it plugged in, or see if there is a response on the computer perhaps on fastboot, upon using the bootloader keys. I haven't had this, just a few suggestions. Good luck!
PS: A RMA will probably be needed, there are much more experienced people around here. Sure you may get replies later.
Good luck?problem all nexus 6p!!! Lg responds repay helps, hawuei what to do? problem arises with nogaut not be our fault, how to fix this? My phone now in service but to be fair this? warranty and having to wait ..