Database Users

[REPAIRED!]LG G2 F320K deep&hard brick! REPAIRED now.

10/10 13:19 updated:
REPAIRED!I got my phone repaired...HERE is the method http://forum.xda-developers.com/showthread.php?t=2477595
Last night I began to try REPAIRING , but it still can not work...
Firstly Pardon me for my poor English...
The reason it stucked is that when i tried to get it back to stock firmware,the software(LG FLASH tool) warmed me with some unknown errors at the time it almostly finished... and after it restarted, it stucked in the starting LG screen...
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Unable to enter download mode,instead,it entered fastboot mode
In fastboot mode,I successfully flashed boot.img, and recovery.img(CWM or TWRP) successfully flashed but could not start,and when I tried flashing system.img it failed
If I boot it directly with USB pluged, the computer will detect the port the same as which appears when you use kdz flashing.. But this port can not use for flashing kdz with LG Support tool, whether it is in diag mode or cs_emergency mode.
What's more,.tot file could not be flashed in by LG Flash Tool,too..
Sometimes,after some special action,it would appear a "qhsusb_bulk" unknown hardware on my computer , and then my computer tells me to format a bunch of "local driver"s
Current ideas:
1 Try to enter recovery from fastboot mode
(2) flash my phone whitout enter download mode
8/10 10:00 update ideas
a. extracted from the official kdz or tot, img could be flashed in in fastboot mode
b. Could You please send me some original DUMPed imgs in LG F320K? (Using Nandroid backup in CWM or TWRP)
Very thankful for your kindness！
10/10 00:30 updated
New discoveries！ boot with holding the volume + and power key for five seconds, it would enter the official Recovery (rescue mode) But if CWM or TWRP flashed it couldn't start..
Hold all the three keys to boot it would enter an unknown New World (look at the picture). . .
But now I have no idea of these two modes...I urgently need F320K dumped partition image! ! Please help me,my friend..Thx very much
Photos was taken with the OLD but faithful, never bricked, NEVER broke after fell down-my Nokia C6, but the quality of images is not good. . .
If this time I can repair it back form brick successfully,I will write down my operation in detail to help the guys who have the same problem as mine..
Very grateful for your help--even just a reply or subscribe!:good:

Have you tried removing the MicroUSB-cable while pressing PWR + Volume down?
That did the trick for me, and I'm pretty much in the same boat.
Remove USB-Cable -> Hold pwr + volume down -> restart -> hold pwr + volume down again when the LG-logo pops up.
Then -> LG Mobile Support Tool and recover from the menu there.
Takes FOREVER to download the software, but still. It works.
My issue now is that I only have 10GB left on my G2. Seems like it thinks its a 16GB instead of a 32GB. Wich annoys the booger out of me.
---------- Post added at 10:16 PM ---------- Previous post was at 10:11 PM ----------
1) Turn off the phone completely (or be superfast with the buttons)
2) Hold volume +
3) Connect the phone to the PC (MicroUSB)
4) Enjoy download-mode.
I'm pretty much in the same boat, and thats what I did to get mine working again.
Used downloadmode to reflash the original FW from the LG Mobile Support Tool.
My issue now is that I only have 10GB left on my G2. Seems like it thinks its a 16GB instead of a 32GB. Wich annoys the booger out of me.

dmbardal said:
Have you tried removing the MicroUSB-cable while pressing PWR + Volume down?
That did the trick for me, and I'm pretty much in the same boat.
Remove USB-Cable -> Hold pwr + volume down -> restart -> hold pwr + volume down again when the LG-logo pops up.
Then -> LG Mobile Support Tool and recover from the menu there.
Takes FOREVER to download the software, but still. It works.
My issue now is that I only have 10GB left on my G2. Seems like it thinks its a 16GB instead of a 32GB. Wich annoys the booger out of me.
---------- Post added at 10:16 PM ---------- Previous post was at 10:11 PM ----------
1) Turn off the phone completely (or be superfast with the buttons)
2) Hold volume +
3) Connect the phone to the PC (MicroUSB)
4) Enjoy download-mode.
I'm pretty much in the same boat, and thats what I did to get mine working again.
Used downloadmode to reflash the original FW from the LG Mobile Support Tool.
My issue now is that I only have 10GB left on my G2. Seems like it thinks its a 16GB instead of a 32GB. Wich annoys the booger out of me.
Click to expand...
Click to collapse
But now the problem, the tool can't detect what my phone is...It knows there's a LG phone but it can't get my phone's version...View attachment 2313927

press the menu on the top there.
The one to the left.
Then you choose "Recovery" or whatnot.
Then you can enter your IMEI-number to identify it.

---------- Post added at 10:16 PM ---------- Previous post was at 10:11 PM ----------
[/COLOR]1) Turn off the phone completely (or be superfast with the buttons)
2) Hold volume +
3) Connect the phone to the PC (MicroUSB)
4) Enjoy download-mode.
I'm pretty much in the same boat, and thats what I did to get mine working again.
Used downloadmode to reflash the original FW from the LG Mobile Support Tool.
My issue now is that I only have 10GB left on my G2. Seems like it thinks its a 16GB instead of a 32GB. Wich annoys the booger out of me.
Click to expand...
Click to collapse
Thx for your new method,BUT I CAN'T get into DOWNLOAD MODE,instead,It brings me into FASTBOOT MODE....
What's More,
I HATE THESE WORDS:
"To prevent spam to the forums, new users must wait five minutes between posts. All new user accounts will be verified by moderators before this restriction is removed."
What can I do to remove this restriction?
dmbardal said:
press the menu on the top there.
The one to the left.
Then you choose "Recovery" or whatnot.
Then you can enter your IMEI-number to identify it.
Click to expand...
Click to collapse
Because my phone isn‘t in download mode,this occurs every time....View attachment 2313955

Since you flashed recovery in fastboot, cant you just do "fastboot restart recovery" to get into it?

You get into fastbootmode when you have your phone off, then you hold the volume + and connect the phone to the computer aswell? :s

wargreymon89 said:
Since you flashed recovery in fastboot, cant you just do "fastboot restart recovery" to get into it?
Click to expand...
Click to collapse
er,no.it seems it doesn't have this command....View attachment 2313987
dmbardal said:
You get into fastbootmode when you have your phone off, then you hold the volume + and connect the phone to the computer aswell? :s
Click to expand...
Click to collapse
It seems that my DOWNLOAD MODE have been lost...What ever I do to my phone,this mode does not appear....

AND sometimes this happens when I try to fix my phone by LG Support Tool,,View attachment 2314009
But I'm really sure my battery is full 100%!! Strange things....

HI I have the same problem!! But My phone entering fastboot everytimes. No recovery, no download mode.

yarik88 said:
HI I have the same problem!! But My phone entering fastboot everytimes. No recovery, no download mode.
Click to expand...
Click to collapse
What's your phone's version? F320L/S/K or D802?

cms88168 said:
What's your phone's version? F320L/S/K or D802?
Click to expand...
Click to collapse
I have a F320K version korea. (((

same problem ... i have D802
only download mode and fastboot working
dont know what to do man ... this sux

I have a VS980. What part of TWRP b/u u need?
Sent from my VS980 4G using Tapatalk 4

yarik88 said:
I have a F320K version korea. (((
Click to expand...
Click to collapse
j_h3000 said:
same problem ... i have D802
only download mode and fastboot working
dont know what to do man ... this sux
Click to expand...
Click to collapse
trxrider31 said:
I have a VS980. What part of TWRP b/u u need?
Sent from my VS980 4G using Tapatalk 4
Click to expand...
Click to collapse
Goooooood NEWS Guys,I got my Brick repaired!!!!
I'll post my method later...because the ****ing 5 minute restriction...
Or you can go http://bbs.gfan.com/android-6735246-1-1.html,I posted there..(in Chinese)...

hey @ all
does this work with D80210A?

49% stucked
if you stucked like i was for 5 days, you can try this
http://forum.xda-developers.com/showpost.php?p=48266517&postcount=1046

cms88168 said:
Goooooood NEWS Guys,I got my Brick repaired!!!!
I'll post my method later...because the ****ing 5 minute restriction...
Or you can go http://bbs.gfan.com/android-6735246-1-1.html,I posted there..(in Chinese)...
Click to expand...
Click to collapse
Hey can you post your method in English? I have the exact same problem with my phone right now. Missing IMEI, phone restarts every 20 seconds, and I've tried reverting back to stock but now CWM is gone, as well as everything in the internal memory. Can you please share in your wisdom how to fix??
Thanks in advance.

My G2 can not go into download mode and recover mode, and my computer can not recognise it so I can not put anything into it.
when I hold Volume up and plug usb cable, its screen has a green robot with red exclamation! and I can go into recovery mode.
How can I do to wake up my phone?

I Bricked My LG G2 VS980 and have no idea what to do
So a couple days ago, I rooted my phone, and everything worked perfectly. Today I tried to install cyanogenmod 11 onto my LG G2 VS980 with Kitkat 4.2.2. I wiped everything on my phone except for the Internal sd card, and installed it. However, when I rebooted my phone, cyanogenmod didn't boot, and my phone is unable to get past the LG logo. It is in a bootloop, and keeps powering on and off unless I turn it off with the power button.
Any help would be greatly appreciated! Thanks!

Axon 7 bricked and I'm in a very tight situation. Any quick solution?

To sum it up quickly, I put my Axon 7 up for sale on ebay. 5 day listing. It currently has ~24 hours left on it and plenty of bidders. ZTE Gladly offered a replacement but it would take 10 or more days. I had previously rooted the phone, and wanted to send it as though it came from the factory. I went into fastboot, did 'fastboot oem lock' over the fastboot shell, and it said successful. The device "rebooted" into a black screen. The device now appears to be bricked. It will show a ZTE logo for about a second when I hold the power button and then no more. I cannot seem to get it respond to a charge, go into fastboot, recovery, or anything else except what I described. It sounds hopeless to me, but maybe someone here is a miracle worker. Thank you very much.

for starters which model to you have?

You were completely stock, not rooted before locking?

lafester said:
You were completely stock, not rooted before locking?
Click to expand...
Click to collapse
I had flashed CM to it previously but when I did a relock I had reflashed stock MiFavor found here on XDA.
Edit: TWRP official a2017u was on the device, and I may have flashed supersu as well during the stock reflash. It was almost a week ago, I can't remember.
DrakenFX said:
for starters which model to you have?
Click to expand...
Click to collapse
A2017U

erer1243 said:
I had flashed CM to it previously but when I did a relock I had reflashed stock MiFavor found here on XDA.
A2017U
Click to expand...
Click to collapse
If you can boot to recovery you can try using ZTE B20 file, look here https://www.zteusa.com/axon-7#support under SOFTWARE UPDATES
* Move that file to your SDCard ,
* Boot to your recovery and flash that file.

DrakenFX said:
If you can boot to recovery you can try using ZTE B20 file, look here https://www.zteusa.com/axon-7#support under SOFTWARE UPDATES
* Move that file to your SDCard ,
* Boot to your recovery and flash that file.
Click to expand...
Click to collapse
I cannot boot into recovery. I cannot do anything except what I described, the quick ZTE logo, and then nothing. The computer does recognize that there is a device plugged in though, but ADB and fastboot will not see it.

erer1243 said:
I cannot boot into recovery. I cannot do anything except what I described, the quick ZTE logo, and then nothing. The computer does recognize that there is a device plugged in though, but ADB and fastboot will not see it.
Click to expand...
Click to collapse
not even Manual boot to recovery?
Press & Hold Volume Up + Power till menu kicks in.
you other option booting to EDL and use @tennear or tenfar tool to flash TWRP ONLY and flash that file or my B29.MergeBootstack and StockSystem files

DrakenFX said:
not even Manual boot to recovery?
Press & Hold Volume Up + Power till menu kicks in.
you other option booting to EDL and use @tennear or tenfar tool to flash TWRP ONLY and flash that file or my B29.MergeBootstack and StockSystem files
Click to expand...
Click to collapse
Nothing happens. It will not go into fastboot or recovery, no matter what I hold, for how long, anything. I believe it is either trying to display the "Your device cannot be trusted" screen and fails or is trying to do some other thing during pre-boot and is stuck in a loop. I don't know what EDL is but I'd be willing to tear this phone a new asshole if I can fix it within 24 hours. Happy to try anything, it seems like it can't get any worse than this.

erer1243 said:
I believe it is either trying to display the "Your device cannot be trusted"
Click to expand...
Click to collapse
this means, you still UNLOCK, when you are there and i mean when that message shows up, press any of the volume key and will give you a menu, from there you can boot to recovery - fastboot - bootloader.
if you see that menu, BOOT to BOOTLOADER and tell me the status.

DrakenFX said:
this means, you still UNLOCK, when you are there and i mean when that message shows up, press any of the volume key and will give you a menu, from there you can boot to recovery - fastboot - bootloader.
if you see that menu, BOOT to BOOTLOADER and tell me the status.
Click to expand...
Click to collapse
Well I just successfully locked it before making the thread... So it is not unlocked any longer. That was just speculation. I have no menus, holding down volume buttons and power does not do anything, I cannot get into fastboot, recovery, etc at all.

erer1243 said:
Well I just successfully locked it before making the thread... So it is not unlocked any longer. That was just speculation. I have no menus, holding down volume buttons and power does not do anything, I cannot get into fastboot, recovery, etc at all.
Click to expand...
Click to collapse
you know how to manually boot to EDL? so you can use any of the tool to flash TWRP.
manually booting to EDL and to make sure is in EDL mode CONNECT your device to your PC/Laptop and open DEVICE MANAGER now just Hold & Press Vol. Up and Down and make sure you are pressing both , if you are using case take the phone out of the case so you can really do it. Once you are pressing and holding both volume keys, press Power and check Device Manager for Qualcomm Port your device is using.
after that just proceed with the rest.

Just to make it a little clearer, to go to EDL mode. Phone must be off when you connect to PC, you hold both volume up/down and then touch power. It will still remain off BUT should now be recognized by the PC's device Manager.

I was in the same situation before. Using tenfar's tool to flash tenfar's TWRP (not official TWRP) the phone will boot TWRP with a locked bootloader. Then, go https://www.zteusa.com/axon-7 there and click the Support tab, then the Software Updates subsection. Download that, it could take a while though.
Once that's done, open the update.zip in something like 7-Zip and navigate to META-INF\com\google\android and extract the file updater-script. Open it with Notepad++ (not Notepad) or, if you're not on Windows, the text editor of your choice.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
On line 2, which is highlighted, delete that line. If you don't do this, it won't flash in TWRP. Don't worry though, it won't mess anything up. After saving, drag the extracted updater-script back into the zip file and confirm that you want to replace it.
Then, once your phone is in TWRP, copy the update.zip to your phone and flash it. For me, it took about 7 or 8 minutes to flash.
This part is the most important, absolutely do not skip this:
Before you reboot go back to the main TWRP menu and open the Mount menu. Uncheck system and then reboot. This is because TWRP installs a survival script in /system if it can, because otherwise TWRP will be changed to stock recovery. In this case though, it's what we want. This way OTA updates will successfully install. Stock recovery checks for any changes to /system and refuses to work if it sees any change at all, like the one TWRP makes unless you unmount system before you reboot.
After rebooting, you should update your phone from B20 to B27 and then from B27 to B29 to be up to date.
Also, this will re-lock your bootloader!
If you have any questions please ask, hopefully that helped you and maybe others too

RainofOranges said:
I was in the same situation before. Using tenfar's tool to flash tenfar's TWRP (not official TWRP) the phone will boot TWRP with a locked bootloader.
Click to expand...
Click to collapse
Maybe I just haven't looked hard enough... but I can't find any working instructions on how to flash/boot to a recovery. When I go by his instructions, nothing seems to work. I have, in the same folder as axon7root.exe, a recovery.img that is tenfar's twrp release. I have installed the driver he linked. I run axon7root -p 4 -r (yes, my phone is connected to the COM4 port) and the program just prints his little copyright splash screen and nothing happens. I have left it for ~half an hour, so it's obviously not just taking it's time. When I unplug the phone, it tells me my horse is dead (lmao someone get on translation) so it obviously knows the phone is there, but it just cannot do anything. Also, I cancelled the ebay listing a few minutes before seeing your post, disappointingly. Hopefully I can revive my horse and relist it.

erer1243 said:
Maybe I just haven't looked hard enough....
Click to expand...
Click to collapse
Are you sure your phone is in EDL mode? Did you try running it through a command promp as Administrator?

RainofOranges said:
Are you sure your phone is in EDL mode? Did you try running it through a command promp as Administrator?
Click to expand...
Click to collapse
I will try running it as admin. I am unsure how to tell if my phone is in EDL mode. I have reason to believe that it is stuck in a silent boot loop and maybe I can't get it into EDL/any other mode but I am just speculating there. I think that because 1, it won't respond to a charge and 2, I have to hold down the power button much longer than usual to make the ZTE logo pop up; It's as though I had to force shut down the phone and then boot it again in the 1 press.

erer1243 said:
Maybe I just haven't looked hard enough... but I can't find any working instructions on how to flash/boot to a recovery. When I go by his instructions, nothing seems to work. I have, in the same folder as axon7root.exe, a recovery.img that is tenfar's twrp release. I have installed the driver he linked. I run axon7root -p 4 -r (yes, my phone is connected to the COM4 port) and the program just prints his little copyright splash screen and nothing happens. I have left it for ~half an hour, so it's obviously not just taking it's time. When I unplug the phone, it tells me my horse is dead (lmao someone get on translation) so it obviously knows the phone is there, but it just cannot do anything. Also, I cancelled the ebay listing a few minutes before seeing your post, disappointingly. Hopefully I can revive my horse and relist it.
Click to expand...
Click to collapse
Mine did that - unplug phone, restart computer, hold both volume buttons and plug phone back in.

erer1243 said:
I will try running it as admin. I am unsure how to tell if my phone is in EDL mode. I have reason to believe that it is stuck in a silent boot loop and maybe I can't get it into EDL/any other mode but I am just speculating there. I think that because 1, it won't respond to a charge and 2, I have to hold down the power button much longer than usual to make the ZTE logo pop up; It's as though I had to force shut down the phone and then boot it again in the 1 press.
Click to expand...
Click to collapse
You can't tell that the phone is in EDL mode on the phone itself. You can only tell by trying the tool. If I remember right the button combination to get into EDL mode is both volume buttons held down and the power button also held down for 2 seconds or so at the same time.

tabletalker7 said:
Mine did that - unplug phone, restart computer, hold both volume buttons and plug phone back in.
Click to expand...
Click to collapse
No dice. As admin, computer restarted, I tried holding both volume buttons while plugging in.

update from my last post: I got tenfar's tool to upload his TWRP to the phone (sent it to the horse o.o) but it still will not boot anywhere. The phone has not changed at all.

checking informations issue

Hello,
I have an issue with my Huawei p9 lite. I updated it to nougat but I hadn't bt, gps and other functions. So I went back to marshmallow downloading the official version on the site Huawei but my problem is : when I configure my phone, it come always back to the wifi+ screen (cancel or activate). The next screen is "checking informations" but this screen stay only 1 seconds and then it go back to the screen "wifi+".
Is someone able to help me plz ?

zanksa said:
Hello,
I have an issue with my Huawei p9 lite. I updated it to nougat but I hadn't bt, gps and other functions. So I went back to marshmallow downloading the official version on the site Huawei but my problem is : when I configure my phone, it come always back to the wifi+ screen (cancel or activate). The next screen is "checking informations" but this screen stay only 1 seconds and then it go back to the screen "wifi+".
Is someone able to help me plz ?
Click to expand...
Click to collapse
Man, you mess up your phone...
Once you are on Nougat you can not flash inferior firmware without preparation...
First need to flash Oeminfo... Without that your phone is not recognized ok by the firmware...

gtdaniel said:
Man, you mess up your phone...
Once you are on Nougat you can not flash inferior firmware without preparation...
First need to flash Oeminfo... Without that your phone is not recognized ok by the firmware...
Click to expand...
Click to collapse
There is nothing to do ?

zanksa said:
There is nothing to do ?
Click to expand...
Click to collapse
there is, just search for "ultimate guide to nougat", it has all info you need.
basically you flash oeminfo and then the stock rom

mjz2cool said:
there is, just search for "ultimate guide to nougat", it has all info you need.
basically you flash oeminfo and then the stock rom
Click to expand...
Click to collapse
Ok thanks a lot. I thought that it was over
I will try this !

mjz2cool said:
there is, just search for "ultimate guide to nougat", it has all info you need.
basically you flash oeminfo and then the stock rom
Click to expand...
Click to collapse
I don't understand it. It says I must install TWRP but I haven't access to my phone because I'm blocked in the configuration and so I can't unlock the bootloader too.
Can someone make me an easy tutorial to follow ? I'm a novice in this field :/

zanksa said:
I don't understand it. It says I must install TWRP but I haven't access to my phone because I'm blocked in the configuration and so I can't unlock the bootloader too.
Can someone make me an easy tutorial to follow ? I'm a novice in this field :/
Click to expand...
Click to collapse
you should be able to unlock the bootloader with fastboot oem unlock (code)

I failed with a file. I flashed a rollback package of nougat to marshmallow instead of the stock rom. And now my Huawei stay blocked on the logo when I turn it on . Any idea of what I can do ? I have the guarantee of my p9 lite too. Maybe should I send it to the repair service ?

zanksa said:
I failed with a file. I flashed a rollback package of nougat to marshmallow in place of the stock rom. And now my Huawei stay blocked on the logo when I turn it on . Any idea of what I can do ? I have the guarantee of my p9 lite too. Maybe should I send it to the repair service ?
Click to expand...
Click to collapse
Man , forget about configuration...
You have to start from scratch...
Power off your phone and try followings:
- power on with <vol–> + <power> and check if start in fastboot mode
- power on with <vol+> + <power> and check if start in recovery mode (twrp or recovery emui)
- power on with <vol–> + <vol+> + <power> and check if start in dload mode
- after that start with USB connection to PC with <vol–> + <power> and see if appear as serial number at fastboot command: devices.
If all works you can start your phone resurrection...

gtdaniel said:
Man , forget about configuration...
You have to start from scratch...
Power off your phone and try followings:
- power on with <vol–> + <power> and check if start in fastboot mode
- power on with <vol+> + <power> and check if start in recovery mode (twrp or recovery emui)
- power on with <vol–> + <vol+> + <power> and check if start in dload mode
- after that start with USB connection to PC with <vol–> + <power> and see if appear as serial number at fastboot command: devices.
If all works you can start your phone resurrection...
Click to expand...
Click to collapse
I can't enter any mode. My phone is alwakys restarting and blocked on the Huawei logo. I can't turn it off

gtdaniel said:
Man , forget about configuration...
You have to start from scratch...
Power off your phone and try followings:
- power on with <vol–> + <power> and check if start in fastboot mode
- power on with <vol+> + <power> and check if start in recovery mode (twrp or recovery emui)
- power on with <vol–> + <vol+> + <power> and check if start in dload mode
- after that start with USB connection to PC with <vol–> + <power> and see if appear as serial number at fastboot command: devices.
If all works you can start your phone resurrection...
Click to expand...
Click to collapse
I have the same situation. No options with button combinations work. I see only such a screen. forum.xda-developers.com/attachment.php?attachmentid=4086705&d=1490344535
Loading is not possible. When I discharged the phone completely and decided to turn on the fast-boot mode, I booted into the android system. Rebooted and again saw the same screen.

Long press more than 10 second on Power not restarting the phone?

gtdaniel said:
Long press more than 10 second on Power not restarting the phone?
Click to expand...
Click to collapse
Yes, it reboots. Double vibrates and again the same screen

loginroman said:
Yes, it reboots. Double vibrates and again the same screen
Click to expand...
Click to collapse
so fast? between (before/after) double vibrate and logo can not make key combination (Vol- + Power)?

I think that I just will not have time between the vibrations. I once booted into the system, somehow miraculously, and tried to work through the ABD, sending a signal to reboot into the fastboot mode, but this is the same result.

gtdaniel said:
so fast? between (before/after) double vibrate and logo can not make key combination (Vol- + Power)?
Click to expand...
Click to collapse
Same for me. Double vibrate and blocked on the Huawei logo. The combinaisons don't work. It was working before I flashed the nougat to marshmallow package but not anymore

At the moment, I booted into android, but I'm just afraid to restart the phone.
---------- Post added at 01:08 PM ---------- Previous post was at 01:06 PM ----------
No no ... I do not see the logo, only that's it forum.xda-developers.com/attachment.php?attachmentid=4086705&d=1490344535
My opinion: the whole section of recovery and fastboot disappeared somewhere. Or they do not work correctly

loginroman said:
At the moment, I booted into android, but I'm just afraid to restart the phone.
---------- Post added at 01:08 PM ---------- Previous post was at 01:06 PM ----------
No no ... I do not see the logo, only that's it ..
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Click to expand...
Click to collapse
Once you are in android, activate developer settings, check Oem unlock and check USB debugging and make authorization of USB debugging!

gtdaniel said:
Once you are in android, activate developer settings, check Oem unlock and check USB debugging and make authorization of USB debugging!
Click to expand...
Click to collapse
I have already done all this. But how to fix this situation. I have HUAWEI Multi-Tool. It reboots into fastboot mode..to unlock the bootloader. And I see this screen again.

Nokia 6 stuck in boot loop

My Nokia 6 (TA-1021) got stuck in boot loop.
Every time i power on the device it gets to the screen that says "Powered by android" and keeps rebooting.
It also shows "shutdown device" on top. How can i get into recovery mode ??
i tried using power + volume up key but it keeps entering the boot loop..
i even tried using adb but as the device is not starting it shows "error: no devices/emulators found".
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

https://forum.xda-developers.com/nokia-6/development/nokia-6-official-firmware-mena-region-t3664441
---------- Post added at 10:08 PM ---------- Previous post was at 10:07 PM ----------
walkn911 said:
My Nokia 6 (TA-1021) got stuck in boot loop.
Every time i power on the device it gets to the screen that says "Powered by android" and keeps rebooting.
It also shows "shutdown device" on top. How can i get into recovery mode ??
i tried using power + volume up key but it keeps entering the boot loop..
i even tried using adb but as the device is not starting it shows "error: no devices/emulators found".
Click to expand...
Click to collapse
https://forum.xda-developers.com/nokia-6/development/nokia-6-official-firmware-mena-region-t3664441

Mine is also so, if you managed to solve please help.
Mine is also so, if you managed to solve please help.

igorbm2010 said:
Mine is also so, if you managed to solve please help.
Click to expand...
Click to collapse
If you know how to flash MENA FIRMWARE then when your pc ask you to connect your device to OST LA tool then plug it, next time when your device will reboot then it will directly go to download mode and hence u could be able to flash your device

sltushar said:
If you know how to flash MENA FIRMWARE then when your pc ask you to connect your device to OST LA tool then plug it, next time when your device will reboot then it will directly go to download mode and hence u could be able to flash your device
Click to expand...
Click to collapse
My phone is also stuck in boot loop and i tried flashing using OST LA but it always shows error.Error detaıls:-
Error code : 0xc6da
Error : Download fails,
Error = SE_ERR_ADB_CMD_GET_FAIL_RESULT (0xC6DA)

Can you enter recovery? What's the recovery version? Have you tried to upgrade to Oreo when bootloop happened?

qwertysmerty said:
Can you enter recovery? What's the recovery version? Have you tried to upgrade to Oreo when bootloop happened?
Click to expand...
Click to collapse
no can't enter into recovery. The phone is already updated to Oreo. And now when i tried to install stock version its stuck in boot loop and shows these error messages when i tried to flash using OST LA.

That's sad since you already have oreo sbl/aboot and cannot enter recovery to downgrade it. I think you have 2 options - either go to service center, or open up your phone to short test point and enter edl mode, but you will lose warranty if you have one.

qwertysmerty said:
That's sad since you already have oreo sbl/aboot and cannot enter recovery to downgrade it. I think you have 2 options - either go to service center, or open up your phone to short test point and enter edl mode, but you will lose warranty if you have one.
Click to expand...
Click to collapse
How to open to short test point and enter edl mode? Thanks in advance.

barun777 said:
no can't enter into recovery. The phone is already updated to Oreo. And now when i tried to install stock version its stuck in boot loop and shows these error messages when i tried to flash using OST LA.
Click to expand...
Click to collapse
Apparently the process to access Recovery Mode changed from Oreo beta to Oreo stable, at least for the TA-1025:
Phone model: Nokia 6 TA-1025
Android version: 8.0.0 (Oreo, stable)
Android security patch level: February 1, 2018
Build number: 00WW_5_22A
Power off your phone.
Connect your phone to a charger.
"POWERED BY android" logo will appear, followed by the battery charging screen.​
[*]Hold VOLUME UP + POWER BUTTON for 10 seconds, release.​
During the 10 seconds, your phone will power cycle, followed by the "POWERED BY android" logo, followed by an image of Bugdroid (Android robot) with the text "no command".​
If you see the the NOKIA logo instead of Bugdroid, you released VOLUME UP + POWER BUTTON too early or too late. Start over.​
From the "no command" screen, hold POWER BUTTON, tap VOLUME UP, release POWER BUTTON. This should take you into Recovery Mode.
Credit to CJShawnz

I faced same problem.i was lucky as i could change it guving 30$ to store to change it.

MisterNeato said:
Apparently the process to access Recovery Mode changed from Oreo beta to Oreo stable, at least for the TA-1025:
Phone model: Nokia 6 TA-1025
Android version: 8.0.0 (Oreo, stable)
Android security patch level: February 1, 2018
Build number: 00WW_5_22A
Power off your phone.
Connect your phone to a charger.
"POWERED BY android" logo will appear, followed by the battery charging screen.​
[*]Hold VOLUME UP + POWER BUTTON for 10 seconds, release.​
During the 10 seconds, your phone will power cycle, followed by the "POWERED BY android" logo, followed by an image of Bugdroid (Android robot) with the text "no command".​
If you see the the NOKIA logo instead of Bugdroid, you released VOLUME UP + POWER BUTTON too early or too late. Start over.​
From the "no command" screen, hold POWER BUTTON, tap VOLUME UP, release POWER BUTTON. This should take you into Recovery Mode.
Credit to CJShawnz
Click to expand...
Click to collapse
Its not working. phone is not gong into the ''no command''. Its stuck in boot-loop.

barun777 said:
Its not working. phone is not gong into the ''no command''. Its stuck in boot-loop.
Click to expand...
Click to collapse
Just put it somewhere and let the bettery be low and then let it properly shutdown
Then put it to charge
Then try to enter to recovery mode
Remember you will have one chance only
Don't power on your device, just follow the steps to enter to the recovery menu, because power on will put u again to boot loop.

sltushar said:
Just put it somewhere and let the bettery be low and then let it properly shutdown
Then put it to charge
Then try to enter to recovery mode
Remember you will have one chance only
Don't power on your device, just follow the steps to enter to the recovery menu, because power on will put u again to boot loop.
Click to expand...
Click to collapse
I have already tried this method. Its not working. Actually I can power off the phone by pressing vol + and vol - buttons together. Boot-loop stops and the phone shutdowns but the navigation LEDs remains in the ON state.

barun777 said:
How to open to short test point and enter edl mode? Thanks in advance.
Click to expand...
Click to collapse
Are you sure you want to do this? You can break your phone. It might be easier to send it to the nearest Nokia service center.
You can find a video on youtube about how to tear down Nokia 6 (JerryRigEverything channel). You need to remove screen and battery plate. Then connect back battery and screen cables. Power up your phone and short test point while phone boots. It should enter EDL mode so you can use whatever flasher. Personally I would just flash sbl/aboot/recovery partitions with images from Nougat using emmcdl. Something like this:
emmcdl -p COM3 -f prog_emmc_firehose_8937_lite.mbn -b recovery recovery.img
where COM3 is the assigned port name. Programmator prog_emmc_firehose_8937_lite.mbn you can take from any Nougat OTA zip, as well as recovery, appsboot, and sbl images.

Did you ever get this sorted? Mine is doing same, OST won't recognise it, keeps saying process failed error = SE_ERR_SUT_PHONE_KEY_ACCESS_FAIL (0xC60E)

Same problem my phone but i go store return my phone he says no solution i am very sad please help us plssss

Axon 7 stuck at boot screen, cannot shutdown and restart.

Hi. Previously I flashed latest TWRP on my B03 Oreo in attempt to root my device but seems like TWRP not mount the internal memory. So I found this thread https://forum.xda-developers.com/android/general/how-to-fix-unable-to-mount-data-t3830897 and followed it but then I stucked at "Your device software can't be checked for corruption. Please lock the bootloader." screen.
I also cannot force shutdown the phone, pressing multiple combinations of power button and volume buttons also doesn't effect the phone at all. Now, i am waiting for the phone's battery to drain until zero. Maybe anyone can help me? If I can boot into EDL, I can reflash back the firmware of my phone and maybe that will solve the problem.

abdinsyakirin said:
Hi. Previously I flashed latest TWRP on my B03 Oreo in attempt to root my device but seems like TWRP not mount the internal memory. So I found this thread https://forum.xda-developers.com/android/general/how-to-fix-unable-to-mount-data-t3830897 and followed it but then I stucked at "Your device software can't be checked for corruption. Please lock the bootloader." screen.
I also cannot force shutdown the phone, pressing multiple combinations of power button and volume buttons also doesn't effect the phone at all. Now, i am waiting for the phone's battery to drain until zero. Maybe anyone can help me? If I can boot into EDL, I can reflash back the firmware of my phone and maybe that will solve the problem.
Click to expand...
Click to collapse
why did you followed that thread?and why use stock twrp.
and when you are the screen that says "Your device software can't be checked for corruption. Please lock the bootloader." just press volume down and select recovery...

Predatorhaze said:
why did you followed that thread?and why use stock twrp.
and when you are the screen that says "Your device software can't be checked for corruption. Please lock the bootloader." just press volume down and select recovery...
Click to expand...
Click to collapse
I follow that thread because my TWRP do not mount the internal sd card in the recovery mode.
I actually used Nfound version of TWRP but it never boot to recovery mode at all.
I cannot press anything at the screen right now. The screen seems to stuck. Is there anything I can do via wire to pc other than adb since adb cannot detect that screen as either edl or fastboot or adb mode.

abdinsyakirin said:
I follow that thread because my TWRP do not mount the internal sd card in the recovery mode.
I actually used Nfound version of TWRP but it never boot to recovery mode at all.
I cannot press anything at the screen right now. The screen seems to stuck. Is there anything I can do via wire to pc other than adb since adb cannot detect that screen as either edl or fastboot or adb mode.
Click to expand...
Click to collapse
you dont have to press the screen.Press volume button and then select recovery with power button

Predatorhaze said:
you dont have to press the screen.Press volume button and then select recovery with power button
Click to expand...
Click to collapse
of course bro, of course. i know that. the buttons won't work that is why i cannot get into any mode. i am stuck at that screen. now it seems like i fixed the problem by draining the battery and then it booted up normally. the problem now is that i will get into the bootloader unlocked screen even i do not press the power button when try charging the phone after its battery completely zero.

Stuck in EDL mode
abdinsyakirin said:
of course bro, of course. i know that. the buttons won't work that is why i cannot get into any mode. i am stuck at that screen. now it seems like i fixed the problem by draining the battery and then it booted up normally. the problem now is that i will get into the bootloader unlocked screen even i do not press the power button when try charging the phone after its battery completely zero.
Click to expand...
Click to collapse
I have a similar problem. My Axon 7 stuck in EDL mode, but no software can connect via USB. No button works, screen is of, no LED. Only sign of life is the 9008 com device in device manager, when I connect it with USB.
I've put it into the freezer right now, to wait until the battery drains. But I think it will take a while, because it was nearly full and the screen is off and not much energy is used for EDL mode.
Any other ideas guys?

mathop said:
I have a similar problem. My Axon 7 stuck in EDL mode, but no software can connect via USB. No button works, screen is of, no LED. Only sign of life is the 9008 com device in device manager, when I connect it with USB.
I've put it into the freezer right now, to wait until the battery drains. But I think it will take a while, because it was nearly full and the screen is off and not much energy is used for EDL mode.
Any other ideas guys?
Click to expand...
Click to collapse
Solution: Got it back to life by draining the battery in the freezer.

I am in the same position, but with no OS and now cannot get to TWRP. Toolkit and MiFlash do not see the device.
Heading for the freezer.

lsulliva said:
I am in the same position, but with no OS and now cannot get to TWRP. Toolkit and MiFlash do not see the device.
Heading for the freezer.
Click to expand...
Click to collapse
if they don't see the device, then you are not stuck in EDL...?
How do you see the phone in the device manager? Or do you see it at all?
Otherwise you're putting it in the freezer for pretty much nothing, as it'll still not be recognized after you charge it again. you might damage the battery (reduce its capacity).

Choose an username... said:
if they don't see the device, then you are not stuck in EDL...?
How do you see the phone in the device manager? Or do you see it at all?
Otherwise you're putting it in the freezer for pretty much nothing, as it'll still not be recognized after you charge it again. you might damage the battery (reduce its capacity).
Click to expand...
Click to collapse
Thanks C a u.
Sometimes it would show up and also as a device in windows! Please see attached image.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I had been flashing bootstackers and matching roms to no avail. Error 08 on TWRP twrp-3.2.3-0-ailsa_ii .
Now, after letting it just sit for a day (?battery discharged), it won't boot into even the warning screen and definitely no recovery.
Disconnected from the PC, Power button gives a brief red led flash. Power held gives a 3 sec red led. Power + Vol + and - in various combos , just the 3 sec led.
Attaching to the PC gives this white screen, which goes off after a couple of seconds. Power button brings it back on, and it stays on, until I disconnect from the PC. Holding power for 15 secs while connected turns the screen off, and pushing power again turns it back on, or sometimes it comes back spontaneously with a few lines across the screen.
Power & Vol +/- combos just bring back the white screen with a few more lines...
It does not show up in device manager, but momentarily is seen by Axon toolkit as an ADB!
Thanks for any guidance you can give.
---------- Post added at 01:59 PM ---------- Previous post was at 01:53 PM ----------
lsulliva said:
Thanks C a u.
Sometimes it would show up and also as a device in windows! Please see attached image.
I had been flashing bootstackers and matching roms to no avail. Error 08 on TWRP twrp-3.2.3-0-ailsa_ii .
Now, after letting it just sit for a day (?battery discharged), it won't boot into even the warning screen and definitely no recovery.
Disconnected from the PC, Power button gives a brief red led flash. Power held gives a 3 sec red led. Power + Vol + and - in various combos , just the 3 sec led.
Attaching to the PC gives this white screen, which goes off after a couple of seconds. Power button brings it back on, and it stays on, until I disconnect from the PC. Holding power for 15 secs while connected turns the screen off, and pushing power again turns it back on, or sometimes it comes back spontaneously with a few lines across the screen.
Power & Vol +/- combos just bring back the white screen with a few more lines...
It does not show up in device manager, but momentarily is seen by Axon toolkit as an ADB!
Thanks for any guidance you can give.
Click to expand...
Click to collapse
Oops, I am just registering for Imgur now. Sorry.

lsulliva said:
Thanks C a u.
Sometimes it would show up and also as a device in windows! Please see attached image.
I had been flashing bootstackers and matching roms to no avail. Error 08 on TWRP twrp-3.2.3-0-ailsa_ii .
Now, after letting it just sit for a day (?battery discharged), it won't boot into even the warning screen and definitely no recovery.
Disconnected from the PC, Power button gives a brief red led flash. Power held gives a 3 sec red led. Power + Vol + and - in various combos , just the 3 sec led.
Attaching to the PC gives this white screen, which goes off after a couple of seconds. Power button brings it back on, and it stays on, until I disconnect from the PC. Holding power for 15 secs while connected turns the screen off, and pushing power again turns it back on, or sometimes it comes back spontaneously with a few lines across the screen.
Power & Vol +/- combos just bring back the white screen with a few more lines...
It does not show up in device manager, but momentarily is seen by Axon toolkit as an ADB!
Thanks for any guidance you can give.
---------- Post added at 01:59 PM ---------- Previous post was at 01:53 PM ----------
Oops, I am just registering for Imgur now. Sorry.
Click to expand...
Click to collapse
You can just attach screenshots to xda, i can see them that way too.
I really want to see this white screen, that sounds very weird. If you can get it to be recognized as Qualcomm HS-USB QDLoader 9008 then you're going to be able to flash whatever from EDL Tool.
So this means you CAN enter TWRP? If you are in TWRP then your phone is just saved, because you just need to know what to flash...

Choose an username... said:
You can just attach screenshots to xda, i can see them that way too.
I really want to see this white screen, that sounds very weird. If you can get it to be recognized as Qualcomm HS-USB QDLoader 9008 then you're going to be able to flash whatever from EDL Tool.
So this means you CAN enter TWRP? If you are in TWRP then your phone is just saved, because you just need to know what to flash...
Click to expand...
Click to collapse
Thanks again
Here are the pics

lsulliva said:
Thanks again
Here are the pics
Click to expand...
Click to collapse
Cannot currently get to twrp.

I am trying to use this tool
to flash an edl ROM. Any suggestions which i should use?
https://forum.xda-developers.com/showpost.php?p=77926571&postcount=35

I just managed to flash A2017G_B10_FULL_EDL, but I had to hold vol+ and - throughout the process! I used Axon 7 toolkit and Miflash 2016.08.30.0. Just going to reboot and factory reset now. Thx for your help C a U.

lsulliva said:
I just managed to flash A2017G_B10_FULL_EDL, but I had to hold vol+ and - throughout the process! I used Axon 7 toolkit and Miflash 2016.08.30.0. Just going to reboot and factory reset now. Thx for your help C a U.
Click to expand...
Click to collapse
Now that I checked my response wasn't even sent lol. Good that you could fix it on your own. Just a heads up, you should use EDL Tool (or standalone MiFlash) instead of axon7toolkit, axon7toolkit is outdated and finicky already.