FYI as how I saved the phone.
Problem: Phone came up only as a Qualcomm HS-USB QDLoader 9008 on COM7.
I downloaded the PD1 debrick image posted in the hardbrick thread as I was on the PD1 bootloader.
Created boot SD card. Installed and powered up phone to download mode.
Flashed JKruses PB1 image via Odin.
Rerooted accroding to JKruse root method for 5.0 using multiple bat files.
Phones back alive running PHX11 ROM with root and Xposed.
Thanks XDA!!!
Related
The help, please! Constantly continued bootloop
There is an insertion, the programmed equipment for FlashTool or Odin
Huawei G7_L01?
I can not come in Fastboot
download ur offcial rom and put in dload folder on ur sdcard. power off ur device and hold power + vol up + vol down and wait until the instalation finish and supposedly it will restored back ur bootloader
Ascend G7-L01 doesn't boot
Hi,
I have the same problem after upgrading my G7-L01 by putting dload in SDcard.
The MUI update started and finished 100% but the phone become bricked!
It is detected as "RELINK HS-USB QDLoader 9008 (Port16)".
I think that I must flash now with SP Flash Tool or other tool! But I didn't find a ROM for that (with scatter).
Thanks for help!
hosnix said:
Hi,
I have the same problem after upgrading my G7-L01 by putting dload in SDcard.
The MUI update started and finished 100% but the phone become bricked!
It is detected as "RELINK HS-USB QDLoader 9008 (Port16)".
I think that I must flash now with SP Flash Tool or other tool! But I didn't find a ROM for that (with scatter).
Thanks for help!
Click to expand...
Click to collapse
i have the same scenario. my phone still bricked. did find any solution to make it boot again ?
After installing CM13 (coming from 20H stock 4.4.2 firmware) I somehow ended up in the hard-brick Qualcomm HS-USB QDLoader 9008 mode.
I fixed this using these steps: http://forum.xda-developers.com/showthread.php?t=2582142 writing that old 2.6.3.2 TWRP and other .bin files extracted from the .kdz
Phone boots OK into CM13 now, but when I try to get into recovery (either using Power+Vol Down or through Advanced Reboot in CM) I get the error:
Secure booting error
Error: Boot Certification Verify!
Click to expand...
Click to collapse
Does anyone know how I can fix this, and flash TWRP? Tried TWRP Manager, Flashify etc, but they all give a flashing error. All fixes for this which I have found online seem to be for people who are running a stock ROM.
(I know going into download mode and returning to stock again etc will sort this, but surely that's not necessary?)
Hi. I rooted phone then i realised i can t update, so i unrooted with an unroot app from google app store. Phone got rebooted and is showing the cyanogen logo since then, so it is bricked.
I can acces fastboot, recoverymode and download mode.
I tried the unbrick guide, tried to flash zui rom via qfil. Problem is i get this error:
Download Fail:Switch To EDL FailSystem.Exception: FireHose Fail
at QC.SwDownloadDLL.SwDownload.SwitchToEDL()
at QFIL.Tech.DownloadTech.SwitchToEDL()
Finish Download
The ports qfil is showing:
shenqui hs-usb diagnostic(com26)
shenqui hs-usb nmea(com27)
shenqui testmode interface(com28)
NO QUSB QDLOADER 9008 Is SHOWING
NONE of them it s working. Is giving me the same error.
i NEED HELP
Excuse me ? Could you please tell me how did you solved this problem ?
Hi there!!!
My OP5 is full dead!!! Black screen, no charging, no buttons !!!
That why ive tried change rom, flashed via twrp installed!!!
I think the good thing is PC can recognize because device in the Qualcomm HS-USB Qdloader 9008 /EDL mode.
I have tried unbrick it, using this tools
QFIL
Q phone download tool
eMMC DL TOOL
Xiaomi Mi Flas Tool
But....................I NEED A STOCK ROM MUST HAVE
“rawprogram0.XML”, “patch0.XML”, “prog_emmc_firehose_8974.mbn” and “MPRG8974.mbn” flashers . ETC, ETC
BECAUSE
OnePlus5OXYGEN_23_OTA_009_all_1707032123_c10521d0fb8b46c0. ZIP
is missing that kind of files.
DOES SOMEBODY CAN TELL ME WHERE CAN I GET THIS KIND OF ROM FOR OP5!!!????
HELP HELP
Get it from the official site
Hello Guys, I have LG G2 F320S (Korean Variant) and a few days ago it was stuck in fastboot mode while i was trying to upgrade to Lollipop firmware using LG Flash Tool 2014. And Fastboot commands were working fine but the problem was that some of the partitions had become write-protected so I was unable to erase or reflash those partitions. So, I short circuit the capacitor and I successfully entered Qualcomm 9006 mode with a number of partitions. I used SRKtool to restore partitions (I have this experience in the past so it was easy for me) but here I noticed 1 or 2 partitions were not restored (write-protected) but phone restarted to download mode. When I tried to flash stock firmware then it always stuck in the middle or something and later once again I was stuck in fastmode mode where I started.
I don't know how partitions became write-protected?
Once again I disassembled the cellphone and short-circuit the capacitor to enter Qualcomm 9006 mode and this time, I wanted to remove write-protection from these partitions so I opened "Diskpart" in "cmd" selected LG G2 and performed clean command and format it. Diskpart removed all the partitions gave me a 32GB single partition like a USB Flash. :laugh:
I thought may be after shorting the capacitor, I will get back partitions but this time I got QDLoader 9008 mode. Now whenever I connect phone to PC with or without battery then it is detected in Qualcomm QDloader 9008 mode.
I tried Boarddiag v3.99c but unfortunately this tool doesn't extract .kdz file of my LG G2 F320S korean variant. I tried to extract .tot file of LG G2 D802 (intl variant) and it completed successfully, so the problem is in .kdz file of my cellphone(probably not supported by this tool).
I can extract this .kdz using LGFirmware extract tool but unfortunately it doesn't create "partition.txt" file which is required in boarddiag to flash partitions. I used partition.txt file of LG G2 D802 but it gives error : No DLoad mode when trying to reflash programmer".
Any help would be appreciated.
#StayHomeStaySafe
Boarddiag full and working version helped
I have tried a lot of times to flash the partitions using boarddiag but it failed. It was the problem of the software because almost all versions had missing files. At last, I have found a working version of boarddiag which detects my phone and I am able to flash boot partitions to it. Although all 3 tests completed successfully (AP, EMMC, SDRAM) but still I am stucked, even after flashing all the boot images, I am still stuck in QDLoader 9008 mode and whenever I connect it to PC (with or without battery), it is detected in QDLoader 9008 mode.
Here is the link to the full working version of Boarddiag 3.99 for LG G2:
https://mega.nz/#!SwY2BQ6L!kPZ6s24hdaVj1x5grboFlAksHSwmItblXIcJCCSaeaw
(mega is blocked in many countries so you may have to use proxy/vpn to open this link)
Here is the result of all 3 tests. Please tell me whats the problem. SDRAM result is FAIL but why so?
https://ibb.co/6ntQwsv
Now I am able to enter "Download Mode" but unable to flash stock or any other firmware. I tried flashing with 2 softwares:
1. LG UP-G2-G3....This software gives error at 6% (at LAF read) as shown in picture below :
https://ibb.co/zXpDcjt
2. LG Flash tool 2014.... This software gives error at 4% by saying "Unable to Establish Connection" though connection is fine because phone is detected in Device Manager and in Download Mode "It shows signs that communication is successful but it wont flash.
salmanzafar said:
Now I am able to enter "Download Mode" but unable to flash stock or any other firmware. I tried flashing with 2 softwares:
1. LG UP-G2-G3....This software gives error at 6% (at LAF read) as shown in picture below :
https://ibb.co/zXpDcjt
2. LG Flash tool 2014.... This software gives error at 4% by saying "Unable to Establish Connection" though connection is fine because phone is detected in Device Manager and in Download Mode "It shows signs that communication is successful but it wont flash.
Click to expand...
Click to collapse
Did you try the TOT flash method already? It worked best for me, when I restored my phone from scratch 2 days ago.
rootarded said:
Did you try the TOT flash method already? It worked best for me, when I restored my phone from scratch 2 days ago.
Click to expand...
Click to collapse
Dear I have tried two methods. I tried LGUP and LG Flash Tools 2014. But both fails. Unfortunately, no TOT file is available for my LG G2 because its Korean variant (F320S) and it has only .kdz firmwares available.
QDLoader 9008 mode
Now, my phone is not entering download mode. It is displayed as QDLoader 9008 mode when connected to PC. Check the screenshot here : https://ibb.co/yk3VSbS
I have the working version of boarddiag but sometimes it passes all 3 tests and sometimes fails EMMC test ad sometimes SDRAM test is not completed successfully.