Database Users

Request : Debrick Image For Grand Prime G530h XXU

Hello There ,
My G530H XXU refuse to turn on ;no boot, no recovery mode and no download mode ! And it's recognized as "qualcomm hs-usb qdloader 9008" when plugged in.
So I guess that am dealing with a hard Bricked phone. Can anyone help me please creating a debrick image or does anyone have one for XXU model ?
Thanks

when you connect it to a computer on the signal odin you see on that?

Nothing, Odin don't detect it , it's hard bricked.
It's detected as "Qualcomm HS-USB QDloader 9008" in the device manager on my PC .
I need the debrick.img to try this solution https://forum.xda-developers.com/verizon-galaxy-note-3/general/howto-recover-hard-brick-t2834419

Could you fix it?? I have the same problem... hqloarder 9008

Fastboot rom, to unbrick my op5

Hi there!!!
My OP5 is full dead!!! Black screen, no charging, no buttons !!!
That why ive tried change rom, flashed via twrp installed!!!
I think the good thing is PC can recognize because device in the Qualcomm HS-USB Qdloader 9008 /EDL mode.
I have tried unbrick it, using this tools
QFIL
Q phone download tool
eMMC DL TOOL
Xiaomi Mi Flas Tool
But....................I NEED A STOCK ROM MUST HAVE
“rawprogram0.XML”, “patch0.XML”, “prog_emmc_firehose_8974.mbn” and “MPRG8974.mbn” flashers . ETC, ETC
BECAUSE
OnePlus5OXYGEN_23_OTA_009_all_1707032123_c10521d0fb8b46c0. ZIP
is missing that kind of files.
DOES SOMEBODY CAN TELL ME WHERE CAN I GET THIS KIND OF ROM FOR OP5!!!????
HELP HELP

Get it from the official site

AXON7 DFU brick

Hi all.
I´m still searching some way to solve my problem.
What´s happaned:
was on AEX OREO, make downgrade to SLIM stock 7.1 from raystef66 = all ok. But after a couple days made magisk upgrade to 17 via twrp and after that is "death"...when I try to start my phone I can see first ZTE logo, than 3x red led, that´s all, I think after flash stockrom I lost customrecovery......?.....t I can not start to TWRP, FASTBOOD...maybe EDL working but:
When I try combo+pwr I see DFU/com4 port. So I tried guidef from raystef66 with ZTE DFU_MultiDL_A2017X_Tool = apk see my phone but still in disconect mode(conect stat) but WIN see my phone as HS USB QDlouder 9008 com 8, now I run edl tool from djkuz.
Tool see my phone, name QUALCOM HS=USB QDlouader 9008 and I tried flash edl or recovery with error = from log:
Did not receive Sahara hello packet from device miflash says can not recivie hallo pocaked.
Any new idea how to fix...?
Thx!!
trying on WIN7 pro

kraljan66 said:
Hi all.
I´m still searching some way to solve my problem.
What´s happaned:
was on AEX OREO, make downgrade to SLIM stock 7.1 from raystef66 = all ok. But after a couple days made magisk upgrade to 17 via twrp and after that is "death"...when I try to start my phone I can see first ZTE logo, than 3x red led, that´s all, I think after flash stockrom I lost customrecovery......?.....t I can not start to TWRP, FASTBOOD...maybe EDL working but:
When I try combo+pwr I see DFU/com4 port. So I tried guidef from raystef66 with ZTE DFU_MultiDL_A2017X_Tool = apk see my phone but still in disconect mode(conect stat) but WIN see my phone as HS USB QDlouder 9008 com 8, now I run edl tool from djkuz.
Tool see my phone, name QUALCOM HS=USB QDlouader 9008 and I tried flash edl or recovery with error = from log:
Did not receive Sahara hello packet from device miflash says can not recivie hallo pocaked.
Any new idea how to fix...?
Thx!!
trying on WIN7 pro
Click to expand...
Click to collapse
First: did the DFU see a com port in the config?
You do have to select the com port manually.
Second: can you boot to FTM?
Third: try another Edl package, some Edl have to be installed as a backup restore not via a straight flashing.

thx for quick answer!
1 see pic pls, in DFU com4
2 no can not get to FTM
3 tried 3x another packages...see log/pic from ZTE EDL tool...

kraljan66 said:
thx for quick answer!
1 see pic pls, in DFU com4
2 no can not get to FTM
3 tried 3x another packages...see log/pic from ZTE EDL tool...
Click to expand...
Click to collapse
Use the latest MiFlash. I've been having trouble with EDL Tool lately. Maybe it'll work. z
I'm guessing the red LED turns off as soon as you connect MultiDL correctly?

Make sure Edl tool is in the root directory of you PC or laptop drive.
EG: C:\ or D:\ as per the instructions.
Make sure you run it as admin too.
If I remember correctly the full Edl package had to be placed into the appropriate folder as per instruction (via the tool) and on the post.

@Syberclone:
I have all as you write...in root, edl package is correct/about edl package edl tool says "success = tried 4different edl package for my phone"/
I´m convinced about a port problem, log from edl tool is:
15:47:25: INFO: User wants to talk to port '\\.\COM8'
ERROR
15:47:25: {ERROR: OpenPort:5198 Failed to open com port '\\.\COM8'
I´ll try another miflash but dont believe ...:-/

just used another PC with WIN7 and now.....CHEEEEERS!!!!!!
Thx to all!

LG G2 hard bricked, partition table lost and stuck in QDLoader 9008 mode

Hello Guys, I have LG G2 F320S (Korean Variant) and a few days ago it was stuck in fastboot mode while i was trying to upgrade to Lollipop firmware using LG Flash Tool 2014. And Fastboot commands were working fine but the problem was that some of the partitions had become write-protected so I was unable to erase or reflash those partitions. So, I short circuit the capacitor and I successfully entered Qualcomm 9006 mode with a number of partitions. I used SRKtool to restore partitions (I have this experience in the past so it was easy for me) but here I noticed 1 or 2 partitions were not restored (write-protected) but phone restarted to download mode. When I tried to flash stock firmware then it always stuck in the middle or something and later once again I was stuck in fastmode mode where I started.
I don't know how partitions became write-protected?
Once again I disassembled the cellphone and short-circuit the capacitor to enter Qualcomm 9006 mode and this time, I wanted to remove write-protection from these partitions so I opened "Diskpart" in "cmd" selected LG G2 and performed clean command and format it. Diskpart removed all the partitions gave me a 32GB single partition like a USB Flash. :laugh:
I thought may be after shorting the capacitor, I will get back partitions but this time I got QDLoader 9008 mode. Now whenever I connect phone to PC with or without battery then it is detected in Qualcomm QDloader 9008 mode.
I tried Boarddiag v3.99c but unfortunately this tool doesn't extract .kdz file of my LG G2 F320S korean variant. I tried to extract .tot file of LG G2 D802 (intl variant) and it completed successfully, so the problem is in .kdz file of my cellphone(probably not supported by this tool).
I can extract this .kdz using LGFirmware extract tool but unfortunately it doesn't create "partition.txt" file which is required in boarddiag to flash partitions. I used partition.txt file of LG G2 D802 but it gives error : No DLoad mode when trying to reflash programmer".
Any help would be appreciated.
#StayHomeStaySafe

Boarddiag full and working version helped
I have tried a lot of times to flash the partitions using boarddiag but it failed. It was the problem of the software because almost all versions had missing files. At last, I have found a working version of boarddiag which detects my phone and I am able to flash boot partitions to it. Although all 3 tests completed successfully (AP, EMMC, SDRAM) but still I am stucked, even after flashing all the boot images, I am still stuck in QDLoader 9008 mode and whenever I connect it to PC (with or without battery), it is detected in QDLoader 9008 mode.
Here is the link to the full working version of Boarddiag 3.99 for LG G2:
https://mega.nz/#!SwY2BQ6L!kPZ6s24hdaVj1x5grboFlAksHSwmItblXIcJCCSaeaw
(mega is blocked in many countries so you may have to use proxy/vpn to open this link)

Here is the result of all 3 tests. Please tell me whats the problem. SDRAM result is FAIL but why so?
https://ibb.co/6ntQwsv

Now I am able to enter "Download Mode" but unable to flash stock or any other firmware. I tried flashing with 2 softwares:
1. LG UP-G2-G3....This software gives error at 6% (at LAF read) as shown in picture below :
https://ibb.co/zXpDcjt
2. LG Flash tool 2014.... This software gives error at 4% by saying "Unable to Establish Connection" though connection is fine because phone is detected in Device Manager and in Download Mode "It shows signs that communication is successful but it wont flash.

salmanzafar said:
Now I am able to enter "Download Mode" but unable to flash stock or any other firmware. I tried flashing with 2 softwares:
1. LG UP-G2-G3....This software gives error at 6% (at LAF read) as shown in picture below :
https://ibb.co/zXpDcjt
2. LG Flash tool 2014.... This software gives error at 4% by saying "Unable to Establish Connection" though connection is fine because phone is detected in Device Manager and in Download Mode "It shows signs that communication is successful but it wont flash.
Click to expand...
Click to collapse
Did you try the TOT flash method already? It worked best for me, when I restored my phone from scratch 2 days ago.

rootarded said:
Did you try the TOT flash method already? It worked best for me, when I restored my phone from scratch 2 days ago.
Click to expand...
Click to collapse
Dear I have tried two methods. I tried LGUP and LG Flash Tools 2014. But both fails. Unfortunately, no TOT file is available for my LG G2 because its Korean variant (F320S) and it has only .kdz firmwares available.

QDLoader 9008 mode
Now, my phone is not entering download mode. It is displayed as QDLoader 9008 mode when connected to PC. Check the screenshot here : https://ibb.co/yk3VSbS
I have the working version of boarddiag but sometimes it passes all 3 tests and sometimes fails EMMC test ad sometimes SDRAM test is not completed successfully.

Bricked Sm-G530h :(((

Please help me.
The problem is that after flashing the rom via odin failed, my Samsung G530H was bricked and can't boot into any more modes like download mode and I tried entering EDL mode when it was banned. go to the computer in the QDloader 9008 port manager can anyone help me unbrick this device (((((