Bricked Jiayu s3, help please - JiaYu S3 Questions & Answers

Hello, I tried an upgrade to android 7.1 but my device is bricked now. It is in a loop and only the Jiayu logo shows up and it shuts off again. Not possible to get it into the (Chinese) recovery mode. It is possible to get it in the fastboot mode though, but when i connect the device to my laptop and run "adb devices" in windows command screen the phone is not found. So i tried to install the right drivers, but without succes. I don not know what to do anymore.
Can anybody help me?
Thanks

don't panic. I am sure you will be NOT the first one that can brick our phone. Let's take it step by step. First of all check with version of S3 you got, and if you installed the correct rom version. Then download (again) the correct one.
You don't have to enter Chinese Recovery. When you power on the phone hold the volume + until after the short vibration and check if you enter the TWRP Recovery. Then report here or install the rom again.
sent from my JiaYu S3 through TapaTalk

gorillaz_gr said:
don't panic. I am sure you will be NOT the first one that can brick our phone. Let's take it step by step. First of all check with version of S3 you got, and if you installed the correct rom version. Then download (again) the correct one.
You don't have to enter Chinese Recovery. When you power on the phone hold the volume + until after the short vibration and check if you enter the TWRP Recovery. Then report here or install the rom again.
sent from my JiaYu S3 through TapaTalk
Click to expand...
Click to collapse
It's a S3 advanced with mt6752, i used the right rom, but i f..ked it up. Sorry.
Press power + volume up gives fastboot mode. That's the only thing that stille opens in the phone.
No recovery, nothing happens. Not starting up, in a loop. Battery is almost empty and won't charge anymore.
So, in my opinion my only chance is fix it with fastboot mode, but my pc cannot find the device.
So, i think that's because of the drivers, but i installed them.
So, i know i can open up the pc for usb connection with windows command, but i don't know the command.
Step by step > which step to do now?
Thanks

Device not found
I don't understand. I installed the drivers and put my laptop in test mode. Still device not found in fastboot. There's nothing i can do anymore. When i can connect the s3 with laptop in fastboot then i can fix this i think. But i am stuck. Any advise?

why don't you use SP Flash Tools to install an older rom? perhaps Rc4? check it out on needrom.
sent from my JiaYu S3 through TapaTalk

Can i flash a rom in this situation? I mean, the phone doesn't do anything, will it be flashed then?
I tried before, but i cannot found scatter file. Where can i find this? I can try flashtool.
On the other hand, why does fastboot not work? Do you understand that?

For flashing I always used this tutorial, it's German but it should be understandable with Google translator: http://mastazone.de/jiayu-flash-anleitung/
Could you exactly tell us what you have done. For example which file did you try to install...
If you have any questions regarding the German site ask me (German native here)
Gesendet von meinem S3 mit Tapatalk

supermar10 said:
For flashing I always used this tutorial, it's German but it should be understandable with Google translator: http://mastazone.de/jiayu-flash-anleitung/
Could you exactly tell us what you have done. For example which file did you try to install...
If you have any questions regarding the German site ask me (German native here)
Gesendet von meinem S3 mit Tapatalk
Click to expand...
Click to collapse
Hello, I tried to put the 7.1 on the s3 but i did it the wrong way obviously. Now the s3 is bricked.
I want to flash, but i need to find an scatter.txt file and it's just not there.
Also my pc cannot find the s3 in fastboot mode.
I hope (and think) there's still a solution, but i am a layman and not that technical. I flashed and fastboot before, but now i cannot succeed somehow.
Can you help me step by step?
I went to the German site and downloaded the SP Flash Tool and the ROM.
Now what to do?

try Google and search for a mtp mega drive pack to install again in your pc...
sent from my JiaYu S3 through TapaTalk

1. Download the file Jiayu RC5
2. Download the MTK VCOM USB[16KB]
3. Download the SP Flashtool V5.1548.00.0000
Extract all files. All downloads from the site linked above
4. Shut down your phone(battery out)
5. Open device manager
6. Connect it by USB to your computer
7. Right mouse click on the entry Mt65xx Preloader
8. Click on update driver
9. Click on search on the computer for drivers(or a similar text)
10. Navigate to the folder you extracted the Mtk vcom USB to
11. Check the box also search sub folders
12. Wait until its finished
13. Open the flashtools software as admin(right mouseclick open as administrator)
14. Click on download(next to Format and Readback)
15. Click on scatterloading file. It is in the folder where you extracted the rc5 file
16. In the drop down box click firmware upgrade
17. First click the green download button and then connect your device. The lower bar should be red at first. It is ready when the green hick shows up
Questions left?
Gesendet von meinem S3 mit Tapatalk
---------- Post added at 11:53 AM ---------- Previous post was at 11:47 AM ----------
This is how the flash tool should look before hitting the download button:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Gesendet von meinem S3 mit Tapatalk

Hallo Mario, yes I have this screen (finally), but it says "PMT changed for the ROM, it must be downloaded" The line was red and 100%, but there it stuck.

Cannot find MT67xx preloader in Device Manager.

Is there any juice left in your battery? Is it still showing the green logo?
Is it charging? If not try removing the battery for a few seconds put it back in and then hook it up to a charger
If the mt65xx does not show up, flashtools won't work.
What operating system do you have? Are the drivers installed correct?
Did the flash tool showed some reaction she plugged the phone in? Like a box with chip info as title? If so the drivers seem to be installed correct.
Are you sure you selected firmware upgrade?
Gesendet von meinem S3 mit Tapatalk

Mario!
The flashing went well, yes! Empty battery, but it worked. I forgot to choose upgrade, thanks my friend.
So, now the s3 is on 5.1
What I want to do is:
Install TWRP on the s3 and then install 7.1
Can I flash TWRP the same way as the firmware?

Glad it worked
TWRP should have been installed automatically at least for me it was. So try to boot to twrp
Gesendet von meinem S3 mit Tapatalk

Yes, you're right. Boot to twrp (2.8.7.0)
Can i install the android 7.1 rom with this twrp or
should i install twrp 3.02 first for installing the upgrade to 7.1?
Can i put twrp 3.0.2 on the phone with fastboot?
Or just copy the software to the internal storage and install with twrp?
Or with flash tool again?
I used to install twrp with fastboot.
Almost there...

I would recommend updating twrp first. Just boot into twrp and flash it
Gesendet von meinem S3 mit Tapatalk

How exactly? Just put the twrp 3.0.2 in the phone (internal storage) and open the phone in twrp recovery and then choose twrp 3.0.2 and install it?

Yeah
At least I did so. I think you could do it with fastboot but I'm not sure
Gesendet von meinem S3 mit Tapatalk

supermar10 said:
Yeah
At least I did so. I think you could do it with fastboot but I'm not sure
Gesendet von meinem S3 mit Tapatalk
Click to expand...
Click to collapse
PC doesn't recognize S3 anymore. Very strange, it did before. So now i cannot drag twrp (new version) to internal storage.
Any suggestions?

Related

[CLOSED]Yoga Tab 2 - what the bri(**ck) is going on?

@MikeChannon removed OP. please close
what? lol
Hey thanks for this explanation! I have a question: Ist it possible to flash a BIOS through dnx? Because i have a different device Intel z3575 SoC, with AMI BIOS and working dnx mode but no booting. I just get bootloops after the manufacturers Logo also I noticed that in BIOS Menu I can't choose any devices to Boot from. Booting into EFI shell or bootable USB stick doesnt work either.. I accidentally flashed a dual Boot BIOS for win/Android to an Android only device. Maybe the partition table is wrecked. I need to find a way to flash the original BIOS, which I have, back on to the device with dnx and mft tool. Any suggestions?
Gesendet von meinem SM-G920F mit Tapatalk
mirco446 said:
Hey thanks for this explanation! I have a question: Ist it possible to flash a BIOS through dnx? Because i have a different device Intel z3575 SoC, with AMI BIOS and working dnx mode but no booting. I just get bootloops after the manufacturers Logo also I noticed that in BIOS Menu I can't choose any devices to Boot from. Booting into EFI shell or bootable USB stick doesnt work either.. I accidentally flashed a dual Boot BIOS for win/Android to an Android only device. Maybe the partition table is wrecked. I need to find a way to flash the original BIOS, which I have, back on to the device with dnx and mft tool. Any suggestions?
Gesendet von meinem SM-G920F mit Tapatalk
Click to expand...
Click to collapse
you need to give more details... what is your tab model? also give me a link to a (known by you) stock rom for your device
First of all thanks for the quick answer.
The Device is Teclast X98 Air iii (3) 32 GB wifi rev. M5C5 I accidentally flashed the BIOS for the x98 air 3g (c5j6) because in tecknights tutorial it was unclear that it was not supported by my device.
The link to the ROMs :
http://forum.xda-developers.com/x98-air/development/mirek190romv5-0-android-lollipop-t3206772
The Rom itself worked at first when I only flashed the Rom and not the BIOS. Then I tried to flash the dual Boot BIOS from Here:
http://forum.xda-developers.com/showpost.php?p=62823494&postcount=3
Because it said compatible with virtually all air devices. I know at least 5 other people who now have the same problem with broken bios and bootloops.
I have the original BIOS file from Teclast site but I cant find the link right now.
If you need the original file I would upload it and provide it but I'm not at my desktop ATM.
Gesendet von meinem SM-G920F mit Tapatalk
mirco446 said:
The Device is Teclast X98 Air iii (3) 32 GB wifi rev. M5C5 I accidentally flashed the BIOS for the x98 air 3g (c5j6) because in tecknights tutorial it was unclear that it was not supported by my device.
Click to expand...
Click to collapse
downlad and extract the attached zip
place your tab in DnX mode (Fastboot Starting...) and input:
fastboot flash osloader efilinux.efi
fastboot boot droidboot.img
tell me if it boots to the droidboot menu
It does Boot to droidboot
Gesendet von meinem SM-G920F mit Tapatalk
mirco446 said:
It does Boot to droidboot
Gesendet von meinem SM-G920F mit Tapatalk
Click to expand...
Click to collapse
have you used the zip file i provided?
there is no zip file attached :/
mirco446 said:
there is no zip file attached :/
Click to expand...
Click to collapse
fixed
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
thats what it boots to. Before it Booted it said couldn't find device handle but it was too fast for me to take a pic
Gesendet von meinem SM-G920F mit Tapatalk
---------- Post added at 01:54 PM ---------- Previous post was at 01:46 PM ----------
You think it would be possible to flash a recovery image that supports adb? Because I have a flashing routine that can flash bios through adb but i dont have adb in this recovery
mirco446 said:
thats what it boots to. Before it Booted it said couldn't find device handle but it was too fast for me to take a pic
Gesendet von meinem SM-G920F mit Tapatalk
---------- Post added at 01:54 PM ---------- Previous post was at 01:46 PM ----------
You think it would be possible to flash a recovery image that supports adb? Because I have a flashing routine that can flash bios through adb but i dont have adb in this recovery
Click to expand...
Click to collapse
i am making now a bios flashing tool from the droidboot image (that is why i needed confirmation that it boots to the droidboot menu)
i will send in in a few minutes a test one (will not change anything, it will just run and reboot at the end, will be used only for testing and after you send me the bios file i will include it and make the final version)
My friend! You got a Donation Account? Would donate you some beer!
Theres the link for the original firmware:
https://drive.google.com/file/d/0B-DELdERnCp-TGp3dDJSeVpUVzA/view?usp=sharing
mirco446 said:
My friend! You got a Donation Account? Would donate you some beer!
Theres the link for the original firmware:
https://drive.google.com/file/d/0B-DELdERnCp-TGp3dDJSeVpUVzA/view?usp=sharing
Click to expand...
Click to collapse
download, extract and input (tab in DnX mode):
fastboot flash osloader efilinux.efi
fastboot boot testboot.img
if ok it will say so on your tab and reboot after the counter
will not change nothing, just test
Okay so it did this again and then after a few seconds it rebooted. Did not See a counter ( was i supposed to?)
Gesendet von meinem SM-G920F mit Tapatalk
Okay, for the readers, ionioni is the man! He managed to create a flashable .img that we can use to restore the original BIOS on m5c5 (and probably other devices) through fastboot/dnx!
I will set up a thread at X98 Air Forums with the details!
Guy doesn't even want me to buy him a beer! Oh and by the way, he did this without having any knowledge about the device at hand true master.
-solved

[GUIDE][TOOL] Reboot to EDL mode from FASTBOOT! No More "Test Point Method"! [kenzo]

[GUIDE][TOOL] Reboot to EDL mode from FASTBOOT! No More "Test Point Method"! [kenzo]
Reboot to EDL mode from FASTBOOT!
No more Test Point Method needed ​
Technical Details:
Redmi Note 3 support rebooting to EDL in Android Bootloader aboot module (the "reboot-edl" command) but fastboot utility doesn't recognize "reboot-edl" in the command line and refuses to sent the command to the device. Since FastBoot command protocol is simple and text-based, it is enough to send a packet containing "reboot-edl" text over USB. The simplest way to do that is to patch Windows fastboot.exe file, replacing "reboot-bootloader" text with "reboot-edl". As "reboot-bootloader" string is found in the command line, fastboot.exe sends the same constant string to the device. So if "reboot-bootloader" is replaced with "reboot-edl", you can specify "reboot-edl" in the command line and the same text will be sent to the device.
New Update: Fastboot updated to latest version.
Tutorial:
1. Download the Fastboot_edl-v2.zip from Here.
2. Extract the zip in your desktop
3. Open the folder and double Click on Reboot.bat
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
4. Reboot your device to Fastboot Mode by pressing
Vol Down + Power button and connect your device with PC and Press Enter.
5. Your Device will be rebooted to EDL!
6. Now flash your Fastboot Rom with Mi Flash Tool to Unbrick your Mi Note 3. ​
Proof:
Thanks to @emuzychenko for the Idea!
This is AWESOME!! Just tested and worked amazingly.
Thank you!
Edit: the included command prompt didn't work for me though, launched standard and traversed to this folder
It would've been better if the source of this guide is also mentioned, just my thoughts
Sent from my Redmi Note 3 using XDA-Developers mobile app
Harish_Kumar said:
It would've been better if the source of this guide is also mentioned
Click to expand...
Click to collapse
Especially since most of text had been copied "as is".
Please add this to op
=> https://youtu.be/-6uErg52nKs
kaushal64 said:
Please add this to op
=> https://youtu.be/-6uErg52nKs
Click to expand...
Click to collapse
I have updated the fastboot.exe and the method also. Update your video with this and I will add it to OP.
I had replaced link for modified fastboot file please add it to op.
Harish_Kumar said:
It would've been better if the source of this guide is also mentioned, just my thoughts
Click to expand...
Click to collapse
emuzychenko said:
Especially since most of text had been copied "as is".
Click to expand...
Click to collapse
Thumbs up!
This is great
My problem solved
Many thanks
not working for me...redmi note 3 pro sd, rom 7.2.7.0.0. it says something like "your phone enter edl mode successfully", but it simply restarts and enter Android OS...
Zarko007 said:
not working for me...redmi note 3 pro sd, rom 7.2.7.0.0. it says something like "your phone enter edl mode successfully", but it simply restarts and enter Android OS...
Click to expand...
Click to collapse
Send me your current emmc_appsboot.mbn and I will check what is happening wrong there.
BRoy_98 said:
Send me your current emmc_appsboot.mbn and I will check what is happening wrong there.
Click to expand...
Click to collapse
Where to find it?
Zarko007 said:
Where to find it?
Click to expand...
Click to collapse
You can find it in the fastboot rom. Or if you have recovery rom, then go to the firmware-update folder in the zip there you will find it.
BRoy_98 said:
You can find it in the fastboot rom. Or if you have recovery rom, then go to the firmware-update folder in the zip there you will find it.
Click to expand...
Click to collapse
Maybe stupid question, but wouldn't phone go to edl mode (with red led flashing) before flashing rom and what then mbn file has to do? According to your manual it is the last step?
thanks
Zarko007 said:
not working for me...redmi note 3 pro sd, rom 7.2.7.0.0. it says something like "your phone enter edl mode successfully", but it simply restarts and enter Android OS...
Click to expand...
Click to collapse
Is your device bricked or you want to flash an official miui rom? Since your rom looks like a distributor rom not an official rom.
Sent from my kenzo using Tapatalk
sator02 said:
Is your device bricked or you want to flash an official miui rom? Since your rom looks like a distributor rom not an official rom.
Sent from my kenzo using Tapatalk
Click to expand...
Click to collapse
No, my device is not bricked, it has locked bootloader. I received code from xiaomi to unlocked bootloader but it constantly stops at 50%, and I found out that it can't be unlocked without china dev rom, but no rom can be installed with locked bootloader I only want to flash an official miui rom to be able to receive updates...Xiaomi really made this too complicated....
Zarko007 said:
No, my device is not bricked, it has locked bootloader. I received code from xiaomi to unlocked bootloader but it constantly stops at 50%, and I found out that it can't be unlocked without china dev rom, but no rom can be installed with locked bootloader I only want to flash an official miui rom to be able to receive updates...Xiaomi really made this too complicated....
Click to expand...
Click to collapse
Don't use this tool if your device is not bricked, your rom is a distributor rom that's why you cannot unlock your device, you have to flash miui rom prior to unlocking, you can do it thru edl mode using adb, search on miui forums and you'll find it.
Edit: check this out: http://en.miui.com/thread-235865-1-1.html
Sent from my kenzo using Tapatalk
Zarko007 said:
No, my device is not bricked, it has locked bootloader. I received code from xiaomi to unlocked bootloader but it constantly stops at 50%, and I found out that it can't be unlocked without china dev rom, but no rom can be installed with locked bootloader I only want to flash an official miui rom to be able to receive updates...Xiaomi really made this too complicated....
Click to expand...
Click to collapse
If your device is not bricked, then you can reboot to EDL mode from adb. Do this to reboot to edl from adb:
1. Connect your device to PC.
2. Open adb and type: adb devices and press enter to see your device if it is connected properly.
3. When you can see your device ID, type: adb reboot edl and press enter. It will reboot your device to EDL mode.
4. Now flash your rom with Mi Flash.
BRoy_98 said:
If your device is not bricked, then you can reboot to EDL mode from adb. Do this to reboot to edl from adb:
1. Connect your device to PC.
2. Open adb and type: adb devices and press enter to see your device if it is connected properly.
3. When you can see your device ID, type: adb reboot edl and press enter. It will reboot your device to EDL mode.
4. Now flash your rom with Mi Flash.
Click to expand...
Click to collapse
I have tried it already many Times but no success...
Zarko007 said:
I have tried it already many Times but no success...
Click to expand...
Click to collapse
This must be driver problem. Install MI PC suite and it will install all necessary drivers. Then try it again.

Convert Chinese Mate 8 to EU variant - noob tutorial

NOOB tutorial - How to convert Chinese Mate 8 to EU variant
I had a rough time to convert my Mate 8, so i am writing this tutorial ( description of the steps i took to be more precise) to help others.
I used couple tutorials on this forum to achive this, so all thanks goes to:
somboons – SRK tool and [GUIDE] How to switch to use stock firmware from other models
duraaraa - Howto: Load International Mate 8 Software on Chinese Mate 8.
Snoop05 - [TOOL] [WINDOWS] ADB, Fastboot and Drivers - 15 seconds ADB Installer v1.4.3
First the tools you will need:
1. 15 seconds ADB Installer v1.4.3
http://forum.xda-developers.com/showthread.php?t=2588979
2. Tool Huawei Bootloader/ROOT/Recovery/Backup/Utility
http://forum.xda-developers.com/mate-8/development/tool-srk-tool-huawei-t3369797
3. EU Rom from duraaraa (download rom only)
http://forum.xda-developers.com/mate-8/general/howto-load-international-mate-8-t3293619
4. stock firmware C432 B152 from somboons link (download rom only)
http://forum.xda-developers.com/mate-8/general/guide-how-to-switch-to-stock-firmware-t3374259
Before next step you need a bootloader key. There are 2 ways, one costs 4 usd, other free. Search the forum how to obtain the key.
Now, what I did:
PART I.
1. Install ADB drivers on PC
2. Install SRK tool
3. Unlock bootloader
4. (I installed twrp and rooted the phone, but I think this is not needed at this point)
Extract rar file that you downloaded with EU rom from duraaraa in directory
C:\1 (or any other name, but keep it short for simplicity)
5. Boot the phone into fastboot mode, using ADB or holding power+volume down.
6. Run the following fastboot commands:
fastboot flash cache c:\1\cache.img
fastboot flash cust c:\1\cust.img
fastboot flash system c:\1\system.img
fastboot flash userdata c:\1\userdata.img
Now, I got EU rom on my Mate 8, BUT, my phone didn’t get wireless reception and showed only 3,8 GB of main storage.
PART II.
Followed the guide from somboons.
1. Install TWRP using SRK tool.
2. Root the phone using SRK tool.
3. Using SRK tool go to “7. Utility” than “9. Changing oeminfo and custom.bin” – choose “2 Mate 8” and then option “2. EU (c432)”
4. unzip update.zip copy update.app from C432 B152 rom to “phone/sdcard/dload/update.app”
5. Install root explorer, edit build.prop in SYSTEM folder of your phone and change line “ro.build.display.id=Deleted” to “ro.build.display.id=NextL00C432B011”
6. Using SRK tool install stock recovery.
7. Now the tutorial says “after boot to system again , press *#*#2846579*#* > 4> 1 (mate 8 , it will be reboot and process install starting..)” but it didn’t work for me.
I switched the phone off, then pressed both volume up and down keys and power.
The phone updated and tadaaaa.. . I was on Stock EU rom, no root, bootloader locked.
Storage encrypted on next boot.
Also i did factory reset and wipe chase from stock recovery, but i do not remember after what was that. i think after step 6. - probably it is not needed.
After this you should have working stock rom.
All that is left is to istall OTA update from phone menu 2 or 3 versions in succession..
If you do not understand something try reading original tutorials from duraaraa and somboons
THE END
Noobs will stop troubling us
sure, IF they actually read this thread ^^ maybe best to stick it into your signature for future reference
Sent from my Huawei Mate 8 NXT-AL10
jbmc83 said:
sure, IF they actually read this thread ^^ maybe best to stick it into your signature for future reference
Click to expand...
Click to collapse
ROFL :laugh:
Hello dears,
First of all, thanks for the clear instruction.
I followed your instruction but I'm stuck at Part 1 - step 6 (fastboot flash cust c:\1\cust.img).
This said FAILED (see below screenshot from ADB)
http://imgur.com/a/6nX4u
And my phone is now not working as normal. Phone getting eRecovery but not working. Please help me!
What do I do now?
Phone model is Huawei Mate 8 NXT-TL00
uugankhuu said:
What do I do now?
Click to expand...
Click to collapse
Unlock the bootloader...
Agadoo said:
Unlock the bootloader...
Click to expand...
Click to collapse
I already unlock my bootloader.
http://imgur.com/a/7oeZc
---------- Post added at 09:08 AM ---------- Previous post was at 09:03 AM ----------
When I install recovery 6.0 (3rd step on SRK tool) it telling me everything is OK
http://imgur.com/a/g1Tof
But when device rebooted it is never going to TWRP. It going to Huawei eRecovery.
uugankhuu said:
I already unlock my bootloader.
Click to expand...
Click to collapse
In fastboot mode you see this?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Agadoo said:
In fastboot mode you see this?
Click to expand...
Click to collapse
Yes, but without text "FRP locked".
is it posible to do it even on latest AL10-nougat update?
BTW guide not working for me.... after i flash all the files in fastboot mode phone reboots and im staring at black screen
Where am i wrong?
One simple doubt: what are the advantages of having the EU variant? I got the chinese mate 8, but I selected my language and I can use it perfectly. Also, as far as I know, chinese firmware gets earlier updates. So, I'm confused.
uugankhuu said:
Hello dears,
First of all, thanks for the clear instruction.
I followed your instruction but I'm stuck at Part 1 - step 6 (fastboot flash cust c:\1\cust.img).
This said FAILED (see below screenshot from ADB)
http://imgur.com/a/6nX4u
And my phone is now not working as normal. Phone getting eRecovery but not working. Please help me!
What do I do now?
Phone model is Huawei Mate 8 NXT-TL00
Click to expand...
Click to collapse
I also get a FAIL on this, and the 3rd one. I'm updated to Nug. on AL-10
faregran said:
One simple doubt: what are the advantages of having the EU variant? I got the chinese mate 8, but I selected my language and I can use it perfectly. Also, as far as I know, chinese firmware gets earlier updates. So, I'm confused.
Click to expand...
Click to collapse
First, Chinese model can't change home launcher. E.g. Google launcher.
Second, in Chinese model didn't installed Google apps and features, even languages. You can't add more languages because it restricted.
Third, device shows lot of necessary Chinese apps and features. E.g. yellow page etc.
and many other.
I bought my phone from Guangzhou, and want install EU version. But still couldn't change Chinese version.

Root Redmi Note 3 Pro! [Install Twrp and Root]

Hi guys today I will tell you that How you can install Twrp Recovery and root your Redmi Note 3 Snapdragon Version.
This method of installing Twrp Recovery also work on any Xiaomi Device. By Any Device i mean the Newer Xiaomi device that comes with a locked bootloader. You just have to replace the Twrp Recovery Image file with your device Recovery image file But i am using my Redmi Note 3 in this video to show you guys the tutorial.
And as I said locked bootloader that means that you have to first unlock your device bootloader to install Twrp on your device.
You can check you my video on it:-
http://goo.gl/gZWfvA
So Now after you have unlocked your phone bootloader let me tell you that how you can install the Twrp Recovery and root your Xiaomi device.
Steps:-
So first Download The 2 files Adb.zip and then extract it and Twrp Recovery for your device.
Then move the Recovery file to the adb folder and make sure that you have installed the adb drivers for your Android phone.
If you don't know how to install it You can check out my video:-
http://goo.gl/a6QgtH
Then download the supersu.zip and the lazyflasher.zip on your micro SD card And Then connect your device to PC via USB cable.
Then open the adb folder And Press and hold the shift button and right click together.
Then click on the CMD option to open CMD And then type The following commands
First type "adb devices" and enter to check that your device is detected.
Then type "adb reboot bootloader" to reboot your phone in fastboot mode.
You can also boot your phone manually in fastboot mode by powering off the device and press and hold the volume down and power button at the same time.
Then type "Fastboot flash recovery" and the name of the Twrp image.
Just type the first 2-3 words of your Twrp image file and press the tab button then it will automatically paste the name of the image file and then press enter to start flashing.
Now you have flashed the Twrp Recovery.
Then you can disconnect your phone and to go in the recovery Just press and hold the volume up and power button together to boot into recovery.
Then you will get this kind of a screen just cancel
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
And if you get this kind of a screen then just "Swipe to Allow Modifications"
And when you go to your internal storage it will not show you your device storage because the device is encrypted.
So to fix this you have to go to wipe and format the data of your device. This will erase everything on your phone not your micro SD card.
So backup everything first
And most of you get this error if you're running miui 8 marshmallow on your phone.
Now you can see your internal storage but now you have to flash the super su zip and the lazy flasher zip That you have placed on your micro SD card earlier.
So go to install and select the storage in which the files are saved and then install both of them.
First install the supersu.zip and then the lazyflasher.zip and Then wipe cache and reboot.
It will take some time at first boot.
Now the super su app will be installed on my phone.
Let's check with the root checker.
So that's how you can root your Redmi Note 3 Very easily and also other Xiaomi devices.
So hope you like it.
Check out my video about this topic:-
https://goo.gl/VQ8gfA
Twrp Image for RN3- https://goo.gl/VKElqg
Lazy Flasher- https://goo.gl/AzC3JD
Super su- https://goo.gl/t23Zok
Adb zip- https://goo.gl/5GSNgj
Why you ppl mess up things ! It's ok for beginners but try to explain all kind of twrp we have for our device and fastboot format user data command properly
Sent from my Redmi Note 3 using Tapatalk
Deleted.
This is good but there's a lot easier method. Just search Redmi note 3 root marshmallow on YouTube. I got the link from another awesome XDA member. Super easy
Sent from my Redmi Note 3 using Tapatalk
bchiu said:
This is good but there's a lot easier method. Just search Redmi note 3 root marshmallow on YouTube. I got the link from another awesome XDA member. Super easy
Click to expand...
Click to collapse
I have also given the link for my YouTube video
No no.. I mean there's this YouTube tutorials I just used yesterday and it took me only 5 mins tops to root my Redmi note 3 pro. Cuz they have a flash.bat file with all the necessary file in one zip file. Put your phone to fastboot and run the flash.bat and it's done. So no need to manually type all those adb commands.
Sent from my Redmi Note 3 using Tapatalk
bchiu said:
No no.. I mean there's this YouTube tutorials I just used yesterday and it took me only 5 mins tops to root my Redmi note 3 pro. Cuz they have a flash.bat file with all the necessary file in one zip file. Put your phone to fastboot and run the flash.bat and it's done. So no need to manually type all those adb commands.
Click to expand...
Click to collapse
Oh!
But don't get me wrong I do appreciate you did this post. I would have follow this guide if I didn't already rooted the easier way.
Sent from my Redmi Note 3 using Tapatalk
bchiu said:
But don't get me wrong I do appreciate you did this post. I would have follow this guide if I didn't already rooted the easier way.
Click to expand...
Click to collapse
Thanks bro?
my phone doesn't boot
Hi, I've followed this guide just to install the twrp so I din't flash the other packages. TWRP was installed succesfully but the system doesn't boot anymore. It keeps locked on the "mi mi.com" screen (without "android" on the bottom). What can I do now?
mammolos said:
Hi, I've followed this guide just to install the twrp so I din't flash the other packages. TWRP was installed succesfully but the system doesn't boot anymore. It keeps locked on the "mi mi.com" screen (without "android" on the bottom). What can I do now?
Click to expand...
Click to collapse
You have to flash the lazy flasher zip from Twrp recovery. I have given the link in the post and then I will boot.
And be patient it take me around real 15 mins to boot. Please always read the full guide
kd8879 said:
Oh!
Click to expand...
Click to collapse
I followed this but the internal storage get encrypted again and again when i go to recovery.
any solution.
also I want to know the TWRP password used to encrypt the backup
X_killer said:
I followed this but the internal storage get encrypted again and again when i go to recovery.
any solution.
also I want to know the TWRP password used to encrypt the backup
Click to expand...
Click to collapse
It actually don't have any password but u just have to wipe the data. Then the problem will be solve. Just go to wipe/format data/and then type yes & wipe
Hey, is this method is applicable for redmi note 3? Android version 5.1.1 miui 8

Too Confusing Problem in ZUK Z1

my zuk z1 is already have Unlocked boot loader and Installed custom TWRP recovery. then i change my rom from ZukUI to dotOS. then i planned to update my recovery... then i download latest build of twrp and i tried to install through twrp old version.. i flashed the .img too/then i restart the mobile into Recovery. its only run the bootloader... i cant open that in a RECOVER MODE. and if i need to install that again , i need root my mobile. but my mobile device model, its said, Unknon... what can i do.. help me guys
Praveenvee said:
my zuk z1 is already have Unlocked boot loader and Installed custom TWRP recovery. then i change my rom from ZukUI to dotOS. then i planned to update my recovery... then i download latest build of twrp and i tried to install through twrp old version.. i flashed the .img too/then i restart the mobile into Recovery. its only run the bootloader... i cant open that in a RECOVER MODE. and if i need to install that again , i need root my mobile. but my mobile device model, its said, Unknon... what can i do.. help me guys
Click to expand...
Click to collapse
It doesn't make sense if you open another post on following problems. Please provide more information which recovery you have and which one(link) you want to flash.
Have you been able to flash twrp he new recovery through fastboot like the first time?
strongst said:
It doesn't make sense if you open another post on following problems. Please provide more information which recovery you have and which one(link) you want to flash.
Have you been able to flash twrp he new recovery through fastboot like the first time?
Click to expand...
Click to collapse
i flashed twrp and installed dotos..then i would like to update my recovery. then i flashed twrp 3.2.1 , after installed in my recovery partition, i choose reboot to recovery. while it booting into recovery, it shows fastboot mode only.
its says,
"Fastboot mode
Status : Unlocked"
"https://dl.twrp.me/kenzo/twrp-3.2.1-0-kenzo.img.html" from here i downloaded
Praveenvee said:
i flashed twrp and installed dotos..then i would like to update my recovery. then i flashed twrp 3.2.1 , after installed in my recovery partition, i choose reboot to recovery. while it booting into recovery, it shows fastboot mode only.
its says,
"Fastboot mode
Status : Unlocked"
"https://dl.twrp.me/kenzo/twrp-3.2.1-0-kenzo.img.html" from here i downloaded
Click to expand...
Click to collapse
You flashed the twrp for Redmi note 3 which codename is "Kenzo".
The zuk z1 has codename "ham".
Please watch the right recovery before you download and flash
strongst said:
You flashed the twrp for Redmi note 3 which codename is "Kenzo".
The zuk z1 has codename "ham".
Please watch the right recovery before you download and flash
Click to expand...
Click to collapse
m yah..i found my device name as "Ham" but i done the flash unfortunately, now what can i do to recover again..? i need help and i cant root my device also.. because " Device Model : Unknown " in my "about phone option in settings.
and when am connected to device with pc, it shows device name as " MTP device ". in this situation i cant configure my adb for install twrp again,meanwhile i tried to root via KingRoot , its also shows "Unknown device" and cant root now..Try again what can i do now..? help me please:crying:
Praveenvee said:
m yah..i found my device name as "Ham" but i done the flash unfortunately, now what can i do to recover again..? i need help and i cant root my device also.. because " Device Model : Unknown " in my "about phone option in settings.
and when am connected to device with pc, it shows device name as " MTP device ". in this situation i cant configure my adb for install twrp again,meanwhile i tried to root via KingRoot , its also shows "Unknown device" and cant root now..Try again what can i do now..? help me please:crying:
Click to expand...
Click to collapse
You bricked your device by flashing a wrong firmware and twrp....
Let's have a look at here, especially the qpst method in the video https://forum.xda-developers.com/zuk-z1/help/zui-rom-qpst-qfil-fastboot-issue-t3632025
strongst said:
You bricked your device by flashing a wrong firmware and twrp....
Let's have a look at here, especially the qpst method in the video https://forum.xda-developers.com/zuk-z1/help/zui-rom-qpst-qfil-fastboot-issue-t3632025
Click to expand...
Click to collapse
but i changed my os from CyanogenMod 12.1 to DotOS Naugat 7.1.2
is it work with that..?
the main problem is my device Model says Unknown.. How i configure that with my phone
Praveenvee said:
but i changed my os from CyanogenMod 12.1 to DotOS Naugat 7.1.2
is it work with that..?
the main problem is my device Model says Unknown.. How i configure that with my phone
Click to expand...
Click to collapse
Have you used actual drivers for zuk z1? You'll find them in the root guide for example.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
strongst said:
Have you used actual drivers for zuk z1? You'll find them in the root guide for example.
Click to expand...
Click to collapse
i'll try with my laptop... i'll post a reply whether its works or not..!
and dont angry with me, I've a double,
is adb or something will recognize my device while its showing "device model as Unknown"
https://drive.google.com/open?id=1rzdG702z0AmOQGq4z6GFTKTfCWi4ZM-E
https://drive.google.com/open?id=1p5BTzBQhFNrFzRnl_xpAA7gm4_fmNq9l
thank you so much my senior
i've try that. and it was work for me..
now am using RR 7.1.2 Nougat..
but it sucks battery of my device.
strongst said:
Have you used actual drivers for zuk z1? You'll find them in the root guide for example.
Click to expand...
Click to collapse
I've problem on using Camera Fv-5 ..and Enabling camera 2 api..ot doesn't Workss

Categories

Resources