Related
Hi to all who have dust between the touch screen digitizer and LCD.
I send my device 3 times to the authorised HTC service center because of this problem, they cleaned it (not perfectly) and the dust was back again after few days of use. This was really ennoying for me...
After several disassemblies, cleaning, research where dust comes in, then assembles I found the flaw.
The dust doesn’t come in via sealing foam between the touch screen digitizer and LCD.
There is a bump defect of phone housing around the volume keys. Inside of the plastic housing is a metal frame, where the touch screen digitizer is stacked on - that frame is a little bended and the touch screen doesn’t stick properly on it (around the volume keys only). When you look close on the phone you can see also a little wider gap between the touch screen top glass and silver plastic housing edge. (See picture)
WARNING
The following directions WILL VOID
your warranty - you are performing
this repair at your own risk.
So, now, what you have to do:
For those, who have already dust in, just simply disassembly your device (if you are brave enough, have all tools and precise hands - maybe some experience ) and remove PROPERLY all dirt with brush, compressed air and antistatic cloth, then assemble it back or send the device to the service center to clean it (wont void the warranty). Before sealing your TD2 (keep it in plastic bag away from dust) prepare a sharp wooden toothpick, neutral transparent or black silicone (you can purchase it from any building material shop) and cotton cloth.
Now you have to clean the gap between whole plastic silver housing frame and touch screen top glass with soft brush. Then use sharp wooden toothpick to impress the silicone into the gap (all gaps you can see, just in case) (silicone does not damage phone housing and TSCR surface and it’s easy to clean), then just gently and properly wipe off all the rest of silicone from phone surface. (be careful not to get silicone to the keys or phone receiver slot)
Leave the phone for several hours to get silicone dry.
Then you can use your TD2 in dusty environment and your display stays absolutely clean and dusty free. (TESTED on mine, for me perfect phone now and I am very happy with it...)
For those who have a little dust in and want to stop come more in and those who are planning to buy TD2 (dont wanna play the lottery faulty or not ), do the same procedure (silicone impress only) after unwrapping your device from plastic package.
GOOD LUCK!!! ENJOY YOUR ABSOLUTELY DUSTY FREE DEVICE!!!
Sorry for my English
I don't know about you guys, but I'm not crazy enough to void the warranty of my phone because of a minor thing like that. When mine gets dirty, I send it back and that's it.
If it gets dirty again, I send it back again...
But, it's a good tutorial for the "brave ones" anyway Thanks for sharing your experience with us.
HastaSSSS
I sent mine back over a week ago due to this dust problem (in fact I delivered it in person to HTC repair center in Milton Keynes) hoping for a quick turnaround.
I'm still waiting for it to come back and missing it terribly. I'm back to using my old Nokia E71 which is a great phone but I like my new one and want it back so I may go down the route of the OP just so I don't have to repeat the return each time I get a dust issue.....
http://forum.xda-developers.com/showthread.php?t=519463
i dont want to hijack this thread. if i am then i am sorry
but hopefully you can input your expertise into this thread or help form an opinion for a new thread
I just got a topaz and want to keep dust from getting in but I'm confused about the sillicon. Could you describe more clearly what it is and maybe post a picture so I have some idea what it should look like.
from the picture, for the second gap, apply the protective foil that comes with the phone. Should solve a bit the problem. Ber in mind that after apply, the touchscreen will not have the same sensitivity. You'll have to tap a little bit harder ...
i think you meant screen protector no?
anyway thx for the info,
if anyone knows how to disassemble this device pls help
yes, screen protector. Better not use the screwdriver ... remember warranty ...
I thought these dust under the screen issues had been fixed long ago, but now it seems the problem that affected my old c600 has come back to ruin my topaz after just 1 week.
Not impressed.
georgeono said:
from the picture, for the second gap, apply the protective foil that comes with the phone. Should solve a bit the problem. Ber in mind that after apply, the touchscreen will not have the same sensitivity. You'll have to tap a little bit harder ...
Click to expand...
Click to collapse
I already use a screen protector. I'm more concerned about the first gap. I really don't want dust to happen since I bought my phone second hand and it doesn't have a warrenty.
you can always use a can of pressurized air to get the dust out. (same you use with PCs)
Wouldn't you need two holes that are connected if your blowing air into the device? One for the air to go in and one for the dust to go out? I don't have any dust under my screen currently and would like it to remain that way. The silicon method doesn't seem to difficult or dangerous which is why I'm interested in what silicon to use.
from what I understood (from the pictures in the 1st post), it's not actually a hole, but a free space = gap.
I opened the D2 (only the two upper screws - for lifting the inner part a bit) and did have a look for "gaps" somewhere around the volume controls - i did not really see a gap
But for getting out the dust: dont blow air into the D2 but get the air out - i actually used a vacuum-cleaner. If you remove the two screws it is possible to lift the LCD below the volume sliders *A LITTLE BIT* (=about 0,5 mm only!!!!!) with a small screw driver to create a gap. It worked quite well. (be aware of high air flow and possible static electricity)
But i really would like to know, where exactly to apply some supplementary sealing to get rid of the dust-problem. Any detailed pic would be appreciated.
axantas said:
But i really would like to know, where exactly to apply some supplementary sealing to get rid of the dust-problem. Any detailed pic would be appreciated.
Click to expand...
Click to collapse
Yeah Me too!
OK, people, just put some neutral silicone between (in the gap) silver plastic frame and touch screen (there is just 0,2 -0,5 mm gap, almost invisible) and you wont get any dust under the touch screen. This is the best solution, you could do it from inside, but its much more complicated...
pedroo said:
OK, people, just put some neutral silicone between (in the gap) silver plastic frame and touch screen (there is just 0,2 -0,5 mm gap, almost invisible) and you wont get any dust under the touch screen. This is the best solution, you could do it from inside, but its much more complicated...
Click to expand...
Click to collapse
What exactly is neutral silicone? Do you have a picture of it so I know what to buy?
I'm about to buy the TD2,
is it so big problem this dust under the screen?
Does it happen often?
luca T said:
I'm about to buy the TD2,
is it so big problem this dust under the screen?
Does it happen often?
Click to expand...
Click to collapse
I've had it for about a week and the user I bought it from had it supposedly for about 3 weeks and so far no dust. I'm still terrified its going to happen though.
pedroo said:
OK, people, just put some neutral silicone between (in the gap) silver plastic frame and touch screen (there is just 0,2 -0,5 mm gap, almost invisible) and you wont get any dust under the touch screen. This is the best solution, you could do it from inside, but its much more complicated...
Click to expand...
Click to collapse
Thanks for the pic, pedroo - so they simply should have glued the digitizer surface a bit more careful to the housing...
...thinking a bit about applying the radical solution - not sure yet
EDIT
"meyourchum" has provded a link to get offical disassembly instruction with lot more information.
Check it for yourself
Hello folks,
I had a chance to work on my friends arc who bought a Rogers version and dropped it. He had it totally mess on the case and needed the full housing replacement.
I hope that doesn't happen to anyone. I didn't take any photos but I am trying to explain everything as it was to help anyone with this.
General Note:
- Anywhere you got stuck, watch some X10 Disassembly video
- Be very gentle to your phone in this process
- Besides all the screws the rest of the phone is put together with glue(Sticky Back) and snap(plastic for main board)
- Using this information on your own risk as I don't take any responsibility if anything happens to your phone.
Instruction
1) Remove the back battery cover. Thats the easiest part
2) Need star shaped screw driver[Trox](I bought the set for $5) there are 4 screws like that and two which opens with phillips screwdriver(tiny) This is what I bought
All the above we all have seen them
3) After removing the 6 screws remove the front fascia of the phone with a guitar picks, something skinny but sturdy*
* I recommend not using anything other than rubber or plastic in the whole process.
4) Main board is snapped in with plastic to the body which easily can be opened.
5) Little board on the bottom is glued(sticky back @ top) which you can remove with pulling little hard but make sure you don't break it.
6) Majority of the wire you see connected to mainboard can be discounted (snap in wires)
7) Removing the screen: from outside of the phone (like you are looking directly to screen like you normally do) you need to put something under neat and raise up the screen. This part has glue as well and its hard to lift but I did it and it should be possible.
8) if you are doing a full housing replacement, then there are stuff here and there that you need to remove and re-use it on the new housing(Like 3.5 mm jack, HDMI lid, etc.)
Good Luck and let me know if you have any questions.
1st time... ehm.. taking the Arc apart, that is!
Helluw there
Just read your post, and thought I wanted to share with you, that I might be opening one of these slick little things. My friend broke his display, and the ISP is talking about some 'off the scale' repair prizes.
...So, he asked me to do the job
Told him I didn't have any experience on the disassembling of this phonetype, but he trusts me it seems
I might return with some questions in case of problems, is that OK with you Nimche?
Greetingz
Hope u have the courage to make a video next time
Sent from my Arc using XDA premium App
xelion said:
Helluw there
Just read your post, and thought I wanted to share with you, that I might be opening one of these slick little things. My friend broke his display, and the ISP is talking about some 'off the scale' repair prizes.
...So, he asked me to do the job
Told him I didn't have any experience on the disassembling of this phonetype, but he trusts me it seems
I might return with some questions in case of problems, is that OK with you Nimche?
Greetingz
Click to expand...
Click to collapse
Sure, no problem. I would be more than happy to answer. Lets see just some general stuff...
Note: anywhere you got stuck, watch some X10 Disassembly video
Note: be very gentle to your phone in this process
- you remove the back battery cover. Thats the easiest part
- you need that star shaped screw driver(I bought the set for $5) there are 4 screws like that and two which opens with phillips screwdriver(tiny)
All the above we all have seen them
after removing the 6 screws
note: besides all the screws the rest of the phone is put together with glue and snap(plastic for main board)
- remove the front fascia of the phone with a guitar picks, something skinny but sturdy*
* I recommend not using anything other than rubber or plastic in the whole process.
- main board is snapped in with plastic to the body which easily can be opened. I change full housing and not sure if you have to remove the hard key button from the bottom end of the phone too or not but that little board on the bottom is glue which you can remove with pulling little hard but make sure you don't break it.
- All the wire you see connected to mainboard can be discounted (snap in wires)
- There is a big one which goes to the screen you have to dis-attach that before removing the screen
- Removing the screen: from outside of the phone (like you are looking directly to screen like you normally do) you need to put something under neat and raise up the screen. This part has glue as well and its hard to lift but I did it and it should be possible.
Good Luck and let me know if you have any questions.
Can you answer this??? It get's hot here (and also in the same spot on the front.. so what's inside at this point??
CPU is right behind the second cover. I wish I could take some photos.
Nimche said:
CPU is right behind the second cover. I wish I could take some photos.
Click to expand...
Click to collapse
Thanks for the clarification. I was also suspecting since this area gets damn hot when playing games and even at charging (sometimes).
So seems like they move the CPU from behind the battery in X10 to near to the camera in Arc .
Can I change only the front faceplate around the screen without removing the mainboard? How easy would that be? I want to change mine to Misty Silver as Rogers only carry the Midnight Blue.
Also, for glued parts, do I have to glue them back on the new housing?
hellocng said:
Can I change only the front faceplate around the screen without removing the mainboard? How easy would that be? I want to change mine to Misty Silver as Rogers only carry the Midnight Blue.
Also, for glued parts, do I have to glue them back on the new housing?
Click to expand...
Click to collapse
Glue part, they are more sticky than glued. You just simply stick it back where it was.
Where is the silver face you found?
This is retarded from them...
Digitizer and screen(one part) are sticked to the front face. In order to for your to change the faceplate only(front) you may have to go through the whole process because the wires from digitizer are going through a big hole to the main board. You don't want to mess around with $700 or $800.
Inside, everything is small. really small. I thought I totally screwed up the whole thing. Technology has gone forward alot since I was a kid putting radio together.
Good Luck
prathaban said:
Thanks for the clarification. I was also suspecting since this area gets damn hot when playing games and even at charging (sometimes).
So seems like they move the CPU from behind the battery in X10 to near to the camera in Arc .
Click to expand...
Click to collapse
Yes, there are two board one above battery and one below batter @ bottom of the phone
On top is the main board
on bottom is the board for hard keys.
Nicely put together but they could have done a better job there....
Are there three parts to the housing? I assume there is the front plate, middle housing with the chrome, and the battery cover. The mainboard should be in the middle with the chrome. So I can't just detach the screen front the front plate? What is holding the three pieces of housing together? The six screws?
There are silver housings on eBay from time to time. Though, blue is a lot more common.
Three pieces. Back battery cover which is nothing.
Then there are two main pieces.
Chrome which is more like a holder of the fascia.
If I remember correctly, the front Fascia is the one holding all the board on it including that metal look piece(aluminum probably)
I will take photos and upload here...
Uploaded photos to the first post...
Hey, I'm looking to replace the chrome piece which has a few nasty chips in it, after removing the second back cover, how easy is it to take off that chrome piece?
Great post
How can I replace digitizer? I dropped my phone and the glass cracked
anyone know where i can get the tiny screw driver? I cant seem to find the correct one. they are either too small or too big.
how easy is it to replace the front cover, ive cracked the top of it and chipped a bit out the side (surrounding the screen) i presume it'd be simple enough. And does anyone know where i can get a good quality/genuine front cover replacement?
soldiers33 said:
anyone know where i can get the tiny screw driver? I cant seem to find the correct one. they are either too small or too big.
Click to expand...
Click to collapse
Sorry, you could have sent a private message.
I bought the screw driver here at local tool shop. Home Depot sells them.
Its called Trox Screw Driver and I bought exactly this one http://www.homedepot.com/webapp/wcs/stores/servlet/ProductDisplay?storeId=10051&productId=100087664&langId=-1&catalogId=10053&ci_sku=100087664&ci_kw={keyword}&cm_mmc=shopping-_-googleads-_-pla-_-100087664&ci_gpa=pla&locStoreNum=618
I don't have the packaging but they should be standard.
Good Luck
mps83 said:
how easy is it to replace the front cover, ive cracked the top of it and chipped a bit out the side (surrounding the screen) i presume it'd be simple enough. And does anyone know where i can get a good quality/genuine front cover replacement?
Click to expand...
Click to collapse
You can find the whole housing between $30 to $40 but the front cover is that actual main piece that holds all the internal components + the screen.
If the crack doesn't bug you much, I would not do it since you have to replace the sticker behind you battery as well, which is not easy to peel off + you have to take the screen off the old front fascia which is glued and kind of hard to take off.
Downside of the whole thing for me was the sticker. I have to find an alternative for this problem.
Hi All
Picked up a Nexus 4 a few days ago and only just noticed (as result of a call) that the proximity sensor is reporting that its "blocked" at all times, so the phone things its against my head. I can workaround this by using the "Power button to hang Up" option but at present cannot access any in call features.
When I look under good light the sensor, there are 2 areas so not sure which is the sensor, I can see what looks like a bubble under both. if you imagine what an air pocket looks like under a screen protector thats what it looks like but its behind the glass, perfectly centred. I guess its possible that something has broken here as a result of the drop, the top left corner was the point of impact, does that seem likely?
I got the phone cheap as it had a broke screen so have a new one coming. Its the full screen, glass and digitizer. Does anyone know of the sensor is part of the screen or does it sit behind and then I could be really screwed!
Ta
bert682 said:
Hi All
Picked up a Nexus 4 a few days ago and only just noticed (as result of a call) that the proximity sensor is reporting that its "blocked" at all times, so the phone things its against my head. I can workaround this by using the "Power button to hang Up" option but at present cannot access any in call features.
When I look under good light the sensor, there are 2 areas so not sure which is the sensor, I can see what looks like a bubble under both. if you imagine what an air pocket looks like under a screen protector thats what it looks like but its behind the glass, perfectly centred. I guess its possible that something has broken here as a result of the drop, the top left corner was the point of impact, does that seem likely?
I got the phone cheap as it had a broke screen so have a new one coming. Its the full screen, glass and digitizer. Does anyone know of the sensor is part of the screen or does it sit behind and then I could be really screwed!
Ta
Click to expand...
Click to collapse
Ok so I did a little more reading and it seems that a gorilla has changed the screen on this phone in the past and he / she has used compound to stick the screen down and some of it has gone around the sensor and the resulting press down on the screen has created a few air pockets.
Looking less forward to changing the screen now as no doubt with my luck the "technician" will have used some crazy heat resistant glue!
Also....missing the speaker grille....funny how you only notice things after you have bought them!
Search for proximity sensor fix after screen replacement here on xda. I've found out that if you switch sides of the little rubber /plastic cover that covers the proximity sensor, your problem will be solved. And the light sensor will work with no problems as well.
Sent from my Nexus 4 using Tapatalk
Sp_Ark said:
Search for proximity sensor fix after screen replacement here on xda. I've found out that if you switch sides of the little rubber /plastic cover that covers the proximity sensor, your problem will be solved. And the light sensor will work with no problems as well.
Sent from my Nexus 4 using Tapatalk
Click to expand...
Click to collapse
Really?
From reading the thing to do is either make the height of the bushing a little larger, height wise. Or, to increase the diameter of the holes.
I like your fix the best though....no messing about, just rotate.
Will give it a go, thanks!
It will work for sure, I posted this fix on a YouTube screen replacement guide of octopus glues I think and its confirmed to work from a lot of people. Then if you use a custom rom go to brightness settings while having auto brightness enabled and try changing light sources from dark to very bright places to see the instant lux values you get. If you are not satisfied with the result try custom auto brightness values.
Sent from my Nexus 4 using Tapatalk
bert682 said:
Really?
From reading the thing to do is either make the height of the bushing a little larger, height wise. Or, to increase the diameter of the holes.
I like your fix the best though....no messing about, just rotate.
Will give it a go, thanks!
Click to expand...
Click to collapse
Yep, I discovered this "fix" in a random youtube comment (was that you @Sp_Ark?) just a few days ago, and it worked for me. Then I found a thread here that confirmed that this could be a solution (which could have saved me a week of frustration).
If there's actually something on the proximity sensor, then you might be screwed. Well, not really, or $10 from China. The module is a snap-in piece with connector ribbon that also has the headphone jack. The prox sensor is the smaller one on the right side (when looking at the screen).
Disassembly of the Nexus 4 is pretty simple compared to many other smartphones. You'll need a T5 TORX wrench/bit for the screws at the bottom, and a very small Phillips driver for all the screws in the inside. You'll also need a tool to split the 2 halves apart (your screen replacement might have come with tools). You can find a couple videos on youtube, as well as a detailed teardown (pics) at ifixit.com. If you have a hairdryer (or an actual heat gun) you can make the process easier by softening the glue with heat, but it's not absolutely necessary. Just go slowly and be careful when prying the halves apart so you don't flex it too much and break the glass back.
Which screen assembly did you get? You can get it where it's just the LCD and the digitizer, and you can also get it that has the bezel and speaker with it. When I replaced the screen on my N4, I got the whole deal with the bezel and speaker, since it meant less work and fewer things to screw up.
Planterz said:
Yep, I discovered this "fix" in a random youtube comment (was that you @Sp_Ark?) just a few days ago, and it worked for me. Then I found a thread here that confirmed that this could be a solution (which could have saved me a week of frustration).
If there's actually something on the proximity sensor, then you might be screwed. Well, not really, or $10 from China. The module is a snap-in piece with connector ribbon that also has the headphone jack. The prox sensor is the smaller one on the right side (when looking at the screen).
Disassembly of the Nexus 4 is pretty simple compared to many other smartphones. You'll need a T5 TORX wrench/bit for the screws at the bottom, and a very small Phillips driver for all the screws in the inside. You'll also need a tool to split the 2 halves apart (your screen replacement might have come with tools). You can find a couple videos on youtube, as well as a detailed teardown (pics) at ifixit.com. If you have a hairdryer (or an actual heat gun) you can make the process easier by softening the glue with heat, but it's not absolutely necessary. Just go slowly and be careful when prying the halves apart so you don't flex it too much and break the glass back.
Which screen assembly did you get? You can get it where it's just the LCD and the digitizer, and you can also get it that has the bezel and speaker with it. When I replaced the screen on my N4, I got the whole deal with the bezel and speaker, since it meant less work and fewer things to screw up.
Click to expand...
Click to collapse
I got a "kit" off eBay, [URL="http://www.ebay.co.uk/itm/181144377215?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT"]http://www.ebay.co.uk/itm/181144377215?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT so it appears to be the complete screen. Ive watched a few videos but from the pictures it looks like the screen comes with the metal backing so I suspect I dont need to remove the old screen from the casing, thoughts?
Im expecting this to be the screen, bezel, and metal backing so I need to do is connect in my motherboard and all the other components.
Am I off in thinking this?
That's the full part. The one you've posted is the type I usually go for, they're good quality so far.
bert682 said:
I got a "kit" off eBay, http://www.ebay.co.uk/itm/181144377215?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT so it appears to be the complete screen. Ive watched a few videos but from the pictures it looks like the screen comes with the metal backing so I suspect I dont need to remove the old screen from the casing, thoughts?
Im expecting this to be the screen, bezel, and metal backing so I need to do is connect in my motherboard and all the other components.
Am I off in thinking this?
Click to expand...
Click to collapse
You made a wise choice, young padawan.
Yeah, that looks to be the entire front assembly, including the screen+digitizer, already installed in the bezel. Also includes the earpiece plus the speaker grill that you're missing. You'll have to swap over the guts, and that's about it. It's easiest to swap the power and volume rocker buttons first since it's a bit harder to get them where they go if you've got the logic board in the way. Just remember that the contact points need to make a ^ rather than a v when you're assembling it with the screen facing down. Tweezers are good to have, especially if they're very long and even better if they're curved. I also recommend doing this over a clean towel to avoid scratching the screen (there'll probably be a film over it too), and the fluffier the towel the better, to catch the tiny screws from flying and disappearing.
Honestly, getting the 2 halves apart is probably the hardest part. They make specialized tools for this, and often the sellers will include them, but it doesn't look like your purchase includes them (mine didn't either). Something plastic is the best choice, since you're less likely to cause cosmetic damage to the plastic (especially the bezel) if you slip (and you will slip). As I said before, GO SLOWLY. Work it apart a little bit at a time, alternate side to side, starting from the bottom. Eventually you'll be able to pull the 2 halves apart.
The battery will be stuck in pretty good and will need to be pried out. If I were you (and a week or so ago, I was you), I'd pop a new battery in while you're at it. At this point in the phone's life, it's probably had at least a few hundred cycles on the battery and has lost 10-20% of its original capacity. The other components shouldn't be nearly as hard to get out. Just pry in various points until the piece pops out. Do not force anything. Just work it out slowly. After you pop off the piece that covers the USB port, there's the board that has the port, and that can be slightly tricky to get out. Best way I found is to slip something small and flat (screwdriver?) into the port and push up and out, and the board should come out easily.
Thankfully, there's only 3 different screws used, and they're all easily differentiated from each other. There's the 2 T5 TORX that hold the halves together, the 2 very short screws with wide heads that hold the battery in place, and the rest that hold everything else are all identical to each other.
It looks like on your assembly, it comes with its own adhesives. Everywhere there's a blue film, pull it off and there'll be adhesive underneath. I'd recommend leaving the film on over the part where the sensor/headphone jack module goes until you're sure you can stick it in place with the proximity sensor not acting wonky. Download an app (I used Phone Tester) that can read the prox sensor. FYI, as long as everything is in place, and you've attached the battery, you can boot the phone without replacing the back cover, and test the sensor (just depress the center bit of the power button board). You don't need to screw everything in, but you should at least screw and tighten down the few that surround the sensor area. Once you've got it reading properly (best of luck), it's time to put all back together.
You should familiarize yourself with the teardown/reassembly guides out there. Go to ifixit.com and have everything ready to look at. This is the video that I used to guide me, and I watched it through a few times before I attempted it myself. You should be just fine with your phone after familiarizing yourself, but if you have any specific problems or questions, feel free to ask, and I'm all too happy to help.
Planterz said:
You made a wise choice, young padawan.
Yeah, that looks to be the entire front assembly, including the screen+digitizer, already installed in the bezel. Also includes the earpiece plus the speaker grill that you're missing. You'll have to swap over the guts, and that's about it. It's easiest to swap the power and volume rocker buttons first since it's a bit harder to get them where they go if you've got the logic board in the way. Just remember that the contact points need to make a ^ rather than a v when you're assembling it with the screen facing down. Tweezers are good to have, especially if they're very long and even better if they're curved. I also recommend doing this over a clean towel to avoid scratching the screen (there'll probably be a film over it too), and the fluffier the towel the better, to catch the tiny screws from flying and disappearing.
Honestly, getting the 2 halves apart is probably the hardest part. They make specialized tools for this, and often the sellers will include them, but it doesn't look like your purchase includes them (mine didn't either). Something plastic is the best choice, since you're less likely to cause cosmetic damage to the plastic (especially the bezel) if you slip (and you will slip). As I said before, GO SLOWLY. Work it apart a little bit at a time, alternate side to side, starting from the bottom. Eventually you'll be able to pull the 2 halves apart.
The battery will be stuck in pretty good and will need to be pried out. If I were you (and a week or so ago, I was you, I'd pop a new battery in while you're at it. At this point in the phone's life, it's probably had at least a few hundred cycles on the battery and has lost 10-20% of its original capacity. The other comments shouldn't be nearly as hard to get out. Just pry in various points until the piece pops out. Do not force anything. Just work it out slowly. After you pop off the piece that covers the USB port, there's the board that has the port, and that can be slightly tricky to get out. Best way I found is to slip something small and flat (screwdriver?) into the port and push up and out, and the board should come out easily.
Thankfully, there's only 3 different screws used, and they're all easily differentiated from each other. There's the 2 T5 TORX that hold the halves together, the 2 very short screws with wide heads that hold the battery in place, and the rest that hold everything else are all identical to each other.
It looks like on your assembly, it comes with its own adhesives. Everywhere there's a blue film, pull it off and there'll be adhesive underneath. I'd recommend leaving the film on over the part where the sensor/headphone jack module goes until you're sure you can stick it in place with the proximity sensor not acting wonky. Download an app (I used Phone Tester) that can read the prox sensor. FYI, as long as everything is in place, and you've attached the battery, you can boot the phone without replacing the back cover, and test the sensor (just depress the center bit of the power button board). You don't need to screw everything in, but you should at least screw and tighten down the few that surround the sensor area. Once you've got it reading properly (best of luck), it's time to put all back together.
You should familiarize yourself with the teardown/reassembly guides out there. Go to ifixit.com and have everything ready to look at. This is the video[/i] that I used to guide me, and I watched it through a few times before I attempted it myself. You should be just fine with your phone after familiarizing yourself, but if you have any specific problems or questions, feel free to ask, and I'm all too happy to help.
Click to expand...
Click to collapse
Awesome, I saw some cheaper screens but that one notes that its LG compliant etc. I bought a set of tools separately so will have all the stuff needed. Didnt think about the battery, will order one as it does make sense!
Thanks for the info, will update as I go.
If you want to have a working battery like it used to be before removing it, you have to be very patient and extra careful while trying to remove it. Use some heat for the glue and try with something very thin like a nylon guitar pick. In anyway don't bent the battery and don't start from top. It will be easier to first remove the mother board. Iv already destroyed 4 5 batteries while trying to remove them. Sorry for my English, I hope you understand.
Sent from my Nexus 4 using Tapatalk
Sp_Ark said:
If you want to have a working battery like it used to be before removing it, you have to be very patient and extra careful while trying to remove it. Use some heat for the glue and try with something very thin like a nylon guitar pick. In anyway don't bent the battery and don't start from top. It will be easier to first remove the mother board. Iv already destroyed 4 5 batteries while trying to remove them. Sorry for my English, I hope you understand.
Sent from my Nexus 4 using Tapatalk
Click to expand...
Click to collapse
Yea was extra careful, used a little heat. Someone has definately replaced the screen on the phone before but seems to have been careful enough as no screws missing etc, except the lost the little speaker grille
New screen in and working well. The proximity sensor seems to be working but it reports all or nothing rather than varied. Is this correct?
bert682 said:
Yea was extra careful, used a little heat. Someone has definately replaced the screen on the phone before but seems to have been careful enough as no screws missing etc, except the lost the little speaker grille
New screen in and working well. The proximity sensor seems to be working but it reports all or nothing rather than varied. Is this correct?
Click to expand...
Click to collapse
Yeah this is normal.
Sent from my Nexus 4 using Tapatalk
bert682 said:
New screen in and working well.
Click to expand...
Click to collapse
Awesome! See, it wasn't too bad, was it? Ifixit gives the N4 a 7/10 for repairability, and that's pretty high for them. After replacing my N4 screen, friend/coworker asked if I could do the same for his HTC One M7 with a completely shattered, yet functional digitizer. I said "HEEEEEEEEEEELL NO!"
Planterz said:
Awesome! See, it wasn't too bad, was it? Ifixit gives the N4 a 7/10 for repairability, and that's pretty high for them. After replacing my N4 screen, friend/coworker asked if I could do the same for his HTC One M7 with a completely shattered, yet functional digitizer. I said "HEEEEEEEEEEELL NO!"
Click to expand...
Click to collapse
No, not with the correct tools. I will admit had I not bought the plastic tools, tweezers etc I may have struggled.
The battery was my main concern, its really stuck down, even though this had been replaced before and likely a less tacky glue used it was still tough. Had to use some heat to soften it and the "battery cover" has seen better days. Next thing to replace is that, just for piece of mind.
All in all, pretty nice experience, the phone seems more modular that other phones I have taken apart which is nice.
The pictures are quite big. Resize the browser window width to shrink the pictures to a more manageable size.
Disclaimer: Perform the following repairs at your own risk. This thread is for educational purposes only. You will void your warranty if you proceed. But that's implied, right?
Disassembly
Many of you will already know how troublesome sending a phone back to the manufacturer for repairs is. This is especially the case for OnePlus, whose after-sales support isn't exceptional, and compared to the price of the OPO itself, their repair costs are by no means affordable ($201 and an unknown amount of days). I've read that a number of forum members have repaired their screens themselves using parts from the internet, but it wasn't all that well documented. So as a mobile phone repairer by profession, I thought it would help a lot of people with broken screens for me to write up a detailed walkthrough/tutorial teaching them how to fix it themselves. Let's get to it!
New: a video! (credits to @stephenlotus)
Note that this guide can be used to replace any modular component; the StyleSwap cover, camera, charging port, you name it - just disassemble your phone until you reach your desired step, replace the faulty/damaged part, then re-assemble it!
Actually obtaining the replacement part? Well, that's another story
Equipment/Materials:
Precision screwdriver set (cross-head/Phillip's head, flat-head)
Sharp craft knife/Stanley knife
Plastic pry tools
Fine-tipped tweezers
Stainless steel pry tools
Thin, rigid cards/guitar picks
Hairdryer/industrial hot air gun (recommended)
Air blower (use this to clean the cameras and lenses before closing it up (not your breath))
A full screen assembly (not just the see-through glass digitizer)*
A roll (or a couple of different widths) of double-sided 3M repair tape or pre-cut 3M tape (see second post)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
*The screen can be bought from various sellers on the internet starting from about $80 for the more repair-friendly version, depending on postage and stuff. Given the exclusive nature of the OnePlus One, any seller that sells a "Genuine/Original/OEM" screen assembly is 95% guaranteed to be an original screen. It isn't profitable for third party manufacturers to produce aftermarket replacements or re-manufacture working LCDs with broken glass (glass broken but LCD still works, remove broken glass and re-laminate a new one onto it). The market is small, because most people would still prefer to RMA their phones.
Also note that this guide assumes you will be re-using the old frame/chassis. If you plan to replace it too, then you will need to remove the earpiece grille (if the new screen doesn't have it) from the old screen, and it's best to move the foam lining from the old frame to the new frame too.
I don't think I'm allowed to disclose sites that sell "original" OnePlus accessories/parts, so get Googling!
Actually, I can now. Mwahahahahaha!
You can buy the screen assembly from sites like eBay and AliExpress. I recommend getting the fully assembled screen, complete with capacitive key backlights:
www.aliexpress.com/item/for-Oneplus...zer-assembly-by-free-shipping/2022582516.html
The one without the button backlights is cheaper, but you'll have to take it from your old screen:
www.aliexpress.com/item/Free-Shippi...mbly-For-Oneplus-One-1-A0001/32245677673.html
Do not get the glass/digitizer only, unless you're up to the challenge, your LCD still works and you want the great savings:
http://www.aliexpress.com/item/Orig...or-OnePlus-One-Free-shipping/32243992827.html
Note: there's absolutely nothing wrong with my OnePlus One (well, except for very mild touchscreen issues). If I were to wait until I actually break it (which is never in a million years), I'd never get around to writing this tutorial. Your experience may vary, depending on severity of damage.
Step 1: Eject the SIM tray.
Step 2: Remove the StyleSwap cover. Using a plastic pry tool, start by lightly wedging it underneath the SIM slot (do not pry), and run it across the gap to release the clips. This ensures minimal/no damage to the battery and/or scratches to the StyleSwap cover, unlike using OnePlus' "Press and Peel" method. Never forget.
Step 3: Using a knife with a sharp tip, remove the rubber screw caps covering the three screws in the middle of the camera lens cover.
Step 4: Unscrew all the screws, and put them in a safe place where you won't lose them.
Step 5: Using a plastic pry tool, pry off the camera cover from the corner near the power button or volume button. Caution! The battery flex may be stuck to the cover, so don't lift it up all the way. Detach it from the cover before fully removing it.
Step 6: Using the aforementioned method, do the same for the speaker assembly. Remove the rubber screw caps, unscrew all the screws and store in a safe place. Note how the screws covered with the caps are smaller.
Step 7: Pry off the speaker assembly, starting from the USB port.
Step 8: Use a plastic pry tool to detach the battery flex connector if it hasn't detached yet, then carefully wedge a stainless steel pry tool underneath the battery, starting at the bottom left corner. This side has less adhesive, so it's easier to start on this side. DO NOT PUSH DOWN INTO THE CHASSIS. Delicate flex cables reside here. Keep all pushing of the pry tool as horizontal as possible.
Step 9: Once the left side of the battery has lifted enough, change directions of the pry tool. Use the left side of the chassis as a leverage point, and lift the battery out of the battery well. Be careful not to puncture or deform the battery. You can use a pry tool to cut the adhesive on the right side off the battery.
Step 10: Unplug all the flex cable connectors off the logic board. There are 4 along the bottom edge and 1 to the left of the camera. DO NOT USE THE LOGIC BOARD AS A LEVERAGE POINT. There are delicate surface mount components on the logic board that can easily be damaged accidentally and are nearly impossible to replace. Hold down the logic board, and pull the flex connector up and away from the board.
Alternatively, if you want to cut to the chase and just replace the screen without removing all that other stuff, you can, by only disconnecting the LCD and digitizer flex (rightmost flex along the bottom and the wide flex in the top left corner respectively) and skipping to Step 19. Just remember to remove the plastic block in Step 16 and also be careful not to overheat the earpiece area.
Step 11: Unscrew the screw holding down the logic board. It is located next to the power button. Do not lose it for mix it up with the other screws. It is different in every dimension.
Step 12: Using a sharp knife, peel the button flexes off the chassis, making sure the bottom edge comes off first and be careful not to cut the flex.
Step 13: Push the digitizer flex away from the logic board so it doesn't get caught, and lift the logic board up from the chassis in an arc motion, starting from the top left corner. Rotate it clockwise while doing so.
Step 14: There is still one connector still connected to the logic board on the underside, and that's the cellular antenna connector. Pull the antenna slightly out of its groove.
Step 15: Detach the antenna connector from the logic board using a plastic pry tool. You can use the logic board as the leverage point here, but make sure there aren't any delicate components nearby.
Step 16: Using a pair of fine-tipped tweezers, remove the plastic block that sits next to the digitizer flex connector.
iFixit's teardown does not cover this. If you don't remove it, the flex connector will be caught and will not come out.
Step 17: Carefully, using a flat-head screwdriver, remove the earpiece. This prevents the diaphragm from being damaged later on, when the hot air gun is used.
CAUTION: the earpiece's diaphragm and voice coil has the tendency to fall apart and separate itself from the rest of the earpiece. Be careful.
Step 18 (optional if doing a screen replacement, just don't damage them in the process): Peel the speaker/antenna/vibrate motor flex and USB port flex from the chassis, and remove them.
Step 19: Evenly heat the bezels of the screen using a hairdryer on high heat setting or a hot air gun on a med-high heat setting (~300 °C/~600 °F) on low airflow setting. This softens the adhesive holding the screen in place, making removal easier. Caution! The chassis can become very hot, as it is metal. Do not heat one area for a prolonged period of time, as it can permanently deform the plastic bezel surrounding the screen (or damage the LCD/digitizer, if it's a working one you intend to reuse).
This step I do not have exact instructions for, because my screen isn't broken. I had to be careful not to break it, as it was my only screen. You can use a knife to pry off broken pieces of glass.
WARNING: If you are removing a working intact display and intend to keep it that way, do NOT separate any of the LCD layers from the glass. As it is laminated, separating it will result in permanent damage to the display assembly.
I don't know what this copper does. It doesn't seem significant. New screen assemblies don't seem to have it. Also note that the screen is removed as a single piece assembly.
Step 20: Scrape off the copper bits and the old adhesive from the chassis using a tool of your choice, making sure to not damage anything else.
Step 21: Clean up your work area to prepare for re-assembly! Be careful of broken glass bits.
Obligatory exploded view pic:
Re-assembly
Now might be a good time to fix your grounding issues! If your touch issues arose from the increase of the device's temperature, you may have to cover the whole metallic back of the LCD with tape too.
Note: if the screen still has issues even when isolated as below, then the screen itself may be faulty.
To re-assemble it, it pretty much is just going through the steps in reverse order. When the phone is fully disassembled and nothing is adhered into place, now's the time to test your replacement screen assembly. You can do so by fitting the screen into the frame without using any adhesive, connect it to the logic board along with the battery and turn it on, or if you're lazy like me, just connect it up like this:
It is not recommended to keep the phone powered on for any longer than a few minutes like this, because the logic board effectively has no heatsink.
Step 1: As mentioned before, the old glue can no longer be reused, so we'll have to apply some adhesive tape, cut by hand. If this were a mainstream phone, it'd be pretty easy to get machine-cut 3M tape that fits the bezel perfectly, to ensure an optimal fit.
Sadly, this isn't the case, so we'll have to resort to rolls of that tape of various widths. You can buy these from eBay by searching "3M double sided repair tape".
Update: pre-cut tape is now an option! You can get it on AliExpress .
I personally used 1 mm for the side bezels and 3 mm for the top and bottom, but experiment to obtain maximum coverage. Make sure you don't cover any sensor holes. Usually, this tape in roll form isn't adequately thick, so double up and use two layers.
IMPORTANT: Check that there aren't remnants of broken glass on the bezel when you install the screen or tape. They can cause the screen to easily break.
Also check that you've moved the earpiece grille and capacitive key backlight pads (if the new screen doesn't have them) over from the old screen to the new one. And if you really want to, move the foam ring surrounding the front camera hole in the glass to. It prevents light from the LCD's backlight from leaking into view.
Step 2: Thread the flexes through their respective holes, and fit the screen into the chassis. Lightly heat the bezels (not too much; you don't want to damage the new LCD) to soften the adhesive, and place the screen face down on a clean, flat surface. Push down on the chassis with moderate force.
Step 3: Replace the rubber plastic block that sits in the digitizer flex slot.
Step 4: Make sure the proximity sensor, light sensor and front camera holes are clean and aren't covered by tape.
Step 5: If they were removed during the disassembly, replace the speaker/antenna/vibrate motor flex, then the USB port flex. Watch out for that weird bit that sticks out on the left ide of the speaker flex. Don't forget to reconnect the cellular antenna down the bottom.
Step 6: Put the earpiece back into the chassis. It should be oriented such that the two contact points are next to the digitizer flex.
Step 7: Reconnect the cellular antenna at the logic board. Do not push hardly unless you're absolutely sure it's aligned correctly.
Step 8: Tuck the antenna back into its groove.
Step 9: When reseating the logic board, ensure that the flex connectors stay clear from it. You don't want to have them end up underneath the logic board. Check that the board is flush with the screw holes.
Step 10: Make sure the front camera is also sitting flush. If it isn't, the camera cover may not fit, and the front camera will not be centered.
Step 11: Reconnect all the flex cables, and replace the logic board screw.
Step 12: Stick the button flexes back down onto the chassis.
Step 13: Straighten all the flex cables by lifting them up and stretching them towards the logic board, the stick them back down.
Step 14: Put the battery back in, then reconnect the flex.
Step 15: Replace the camera cover and screw it back into place.
Step 15b: Replace the tamper seal/water damage indicator (you won't get warranty either way, but might as well)
Step 16: Put the speaker assembly back in, and screw it into place.
Step 17: Replace all the rubber screw caps.
Step 18: Replace the StyleSwap cover, and put the SIM tray (with card) back in. Although the tray fits either way (like in Sony's Xperia Z series phones), the side with the gold contacts should face up when the phone faces down. Inserting it upside down will result in the phone not reading the SIM card, and risk damage to the internal SIM reader. LG, HTC and Apple's phones' SIM trays are designed to only fit one-way.
Step 19: Turn the phone on, and enjoy the results of your efforts!
Added to OnePlus One index thread:
[INDEX] OnePlus One Resources Compilation Roll-Up
Transmitted via Bacon
How difficult is this repair for someone who has no experience repairing phones?
I broke my screen 2 days ago and I'm wondering if it's worth trying to repair it, this guide seems pretty solid but some steps look like you might easily break the phone entirely.
naithantu said:
How difficult is this repair for someone who has no experience repairing phones?
I broke my screen 2 days ago and I'm wondering if it's worth trying to repair it, this guide seems pretty solid but some steps look like you might easily break the phone entirely.
Click to expand...
Click to collapse
If you have no experience it'll probably be pretty difficult for you, unless you have a good technical/mechanical mind.
timmaaa said:
If you have no experience it'll probably be pretty difficult for you, unless you have a good technical/mechanical mind.
Click to expand...
Click to collapse
I guess it should be possible to do it myself then, or at least give it a try
I'll probably order a new screen tomorrow, will post here in a month or so when the screen arrived
Query
Excellent guide and I have all the bits removed from the old frame.
I thought I would be an easier route to use a brand new frame, instead of trying to heat the old LCD off.
I have tested everything on the bench and it powers up and we have touch screen
But I have now stopped the reassembly to check the following out. The new frame although having the required sticky parts does not have the black parts, which I assume is insulation.
Do I need this? what can I replace it with, is insulation tape ok although slightly thicker or maybe thin scotch magic tape? The guide mentions a good time to fix the touch screen issues, in the 4 days I had it prior to the drop, I don't think I had an issues, but does this need to be done, and am I right in reading that's also just cover the metal of the screen with insulation tape or scotch magic tape again?
I have attached an image of the black tape I refer to on the frame
Thanks,
Stephen.
CyberActive said:
Query
Excellent guide and I have all the bits removed from the old frame.
I thought I would be an easier route to use a brand new frame, instead of trying to heat the old LCD off.
I have tested everything on the bench and it powers up and we have touch screen
But I have now stopped the reassembly to check the following out. The new frame although having the required sticky parts does not have the black parts, which I assume is insulation.
Do I need this? what can I replace it with, is insulation tape ok although slightly thicker or maybe thin scotch magic tape? The guide mentions a good time to fix the touch screen issues, in the 4 days I had it prior to the drop, I don't think I had an issues, but does this need to be done, and am I right in reading that's also just cover the metal of the screen with insulation tape or scotch magic tape again?
I have attached an image of the black tape I refer to on the frame
Thanks,
Stephen.
Click to expand...
Click to collapse
If it was originally in the phone, it's always a good idea to replace it, or use a substitute in place of it. I don't know how it'll affect the phone's functionality if it isn't replaced, because I've never tried it. It's best to play it safe and tape up those corresponding areas with electrical tape. Scotch tape may be too thin.
Dang, 4 days??
Also, does your replacement screen have the earpiece grille pre-installed? When I disassembled mine, the earpiece was not part of the frame, but stuck to the screen.
vantt1 said:
If it was originally in the phone, it's always a good idea to replace it, or use a substitute in place of it. I don't know how it'll affect the phone's functionality if it isn't replaced, because I've never tried it. It's best to play it safe and tape up those corresponding areas with electrical tape. Scotch tape may be too thin.
Dang, 4 days??
Also, does your replacement screen have the earpiece grille pre-installed? When I disassembled mine, the earpiece was not part of the frame, but stuck to the screen.
Click to expand...
Click to collapse
Ok making some progress
Turns out the black that's under the flat connectors is there on the replacement frame, just a different colour.
I am starting to think that the black that's under the main board could be some sort of heat sink tape? I am referring the black that's actually stuck to the logic board on the top and also on the frame below the logic board and linked to the rear facing camera.
I have tried to remove the old screen with a hair dryer but have failed miserably. So I can not see for myself what the black under the screen was like can you remember if it was like what I believe to be heat sink tape or was it just adhesive or insulation?
Thanks for the heads up about the speaker grill, that is attached to the old screen, I managed to break that out as that's where the screen was smashed.
I have also noticed there is some conductive tape that bridges the frame and back of the screen together, that's not on the replacement parts.
There is also an adhesive o ring stuck to the glass in the front facing camera slot that's not on there replacement part.
Hopefully will get it rebuilt soon
Thanks Stephen
CyberActive said:
Ok making some progress
Turns out the black that's under the flat connectors is there on the replacement frame, just a different colour.
I am starting to think that the black that's under the main board could be some sort of heat sink tape? I am referring the black that's actually stuck to the logic board on the top and also on the frame below the logic board and linked to the rear facing camera.
I have tried to remove the old screen with a hair dryer but have failed miserably. So I can not see for myself what the black under the screen was like can you remember if it was like what I believe to be heat sink tape or was it just adhesive or insulation?
Thanks for the heads up about the speaker grill, that is attached to the old screen, I managed to break that out as that's where the screen was smashed.
I have also noticed there is some conductive tape that bridges the frame and back of the screen together, that's not on the replacement parts.
There is also an adhesive o ring stuck to the glass in the front facing camera slot that's not on there replacement part.
Hopefully will get it rebuilt soon
Thanks Stephen
Click to expand...
Click to collapse
Yeah, that tape is very similar to the type that's found on the inside of the iPhone 5's midframe. Apparently it's a "heat dissipation shield" film. You can probably buy it on eBay then trim it to the same shape as the original.
I don't know what that copper stuff that bridges the LCD to the frame is. I scraped off the bridging bits, and nothing seems off on my end.
Replace that O ring if you can. If you use the front camera, the backlight from the LCD might leak into view. I know it does on the Nexus 5.
Great stuff, slowly getting there, I will get that orderderd and cut to size, these are what I am looking at:
http://www.ebay.co.uk/itm/iPhone-4-...K_Replacement_Parts_Tools&hash=item418dc2333a
and / or
http://www.ebay.co.uk/itm/1x-iPhone...nk-dissipation-adhesive-sticker-/171636569146
Was it this same stuff that was on the frame surface behind the LCD? or was that just insulation?
Also you mentioned the touch screen fix, what is involved in that?
Thanks Stephen.
CyberActive said:
Great stuff, slowly getting there, I will get that orderderd and cut to size, these are what I am looking at:
http://www.ebay.co.uk/itm/iPhone-4-...K_Replacement_Parts_Tools&hash=item418dc2333a
and / or
http://www.ebay.co.uk/itm/1x-iPhone...nk-dissipation-adhesive-sticker-/171636569146
Was it this same stuff that was on the frame surface behind the LCD? or was that just insulation?
Also you mentioned the touch screen fix, what is involved in that?
Thanks Stephen.
Click to expand...
Click to collapse
The stuff behind the LCD is more of a foam tape/film than a graphite tape. It feels similar to the one found behind the Nexus 5's LCD, but darker and smoother. And of course, the Nexus 5's isn't big enough.
The touchscreen fix involves putting tape on the chassis underneath the digitizer flex. If the issue was heat related, the metallic back of the LCD may need to be taped up too (apparently along the perimeter, creating a rectangle).
See above picture, circled in red: it looks like there's some heat dissipation tape underneath the LCD too.
Ah ok, any suggestions on what I could replace the stuff behind the LCD with then? I have searched for the nexus 5 stuff and I can no locate any of that either.
Thanks,
Stephen.
CyberActive said:
Ah ok, any suggestions on what I could replace the stuff behind the LCD with then? I have searched for the nexus 5 stuff and I can no locate any of that either.
Thanks,
Stephen.
Click to expand...
Click to collapse
At the moment the best way to obtain it would probably be to take it out of your old frame. It's really hard to find OnePlus One specific parts these days.
guess I will have to go buy a heat gun over the next few days as I tried using a hair dryer and was not able to get even a little bit of movement on lifting the lcd from the frame.
I will post back over the new few days how it goes. fingers crossed.
I followed this guide and it was perfect!
The only downside is that when heating the screen i've managed seperate the plastic bezel from the screen it's self which is now out of shape as well. I'm hoping if i just heat it back up a little I can reform it back.
Just waiting on delivery of some repair tape.
hi guys i just send my one to repair for over 150€ because i thought it could only be changed as a wholle.. screen functions online half of the screen touchscreen doesnt work becuase of a small crack on the side.....SO DO I NEED JUST A NEW TOUCH DIGITIZER??? is this also with the corning glass on top?? mits not right??
Finally got everything I needed to go ahead with the screen replacement. This teardown was extremely helpful. I did have one snag and I haven't tested yet. When removing the earpiece it disassembled into two pieces and unwound but I gingerly repositioned the copper thread and left the earpiece in during the heating and old screen removal.
The new screen is outstanding and completely changes the experience of using the One Plus One. I only wish they had done better quality control in the first place.
Thanks for this guide. I'm going to order a new screen/digitizer today. I guess in about a month I'll be attempting this. When I broke my OnePlus I ordered a new one that day, so I plan on selling the second one if this repair is successful. If it's not, then I guess I lose $70 and some time. Wish me luck!
This is interesting. If appears a new battery technology would be nice guide.
Dear xda,
while being on holiday in South-East Asia, I got into some pretty heavy rain and my OnePlus 2 obviously didn't like the rain - the display seems to be broken since. Unfortunately I tried switching the phone on shortly after the water contact (because I needed it for navigation) and the display worked just fine while the phone seemed to be stuck software-wise (although now from a retrospective point of view it could have been that already then the display was somehow having issues).
I did put it in dry, uncooked rice just a few hours after the water contact and kept it there for a few days, with the SIM-Tray ejected and the back cover taken off. Still, after a few days, I tried switching it on again and I could notice that is was booting up just fine (I could see the capacitative buttons lighting up and even got some notification sounds after it booted up), but the display remained black
Back home I removed not only the SIM-Tray and the back cover but also the "inside cover" as well as the battery (it then looked like THIS) and put the phone back into rice for another 2 days. After that I reassambled the phone and tried switching it on again - still the display wasn't working.
After disassembling the phone again and taking the battery out, I put the remaining parts of the phone into the oven at about 45°C = 113°F for about 2h. But that didn't help either.
Is there any advice as how to maybe get my display working again? Maybe some cable or connection inside the phone that I could inspect or disconnect and reconnect? The process of buying a display on eBay and replacing the display seems to be rather complicated (due to the fact that the display is glued to the frame as from what I could see on ifixit.com) and I don't want to damage more than I already did while maybe the repair attempt doesn't help at all.
Does anyone have any experience/insight regarding how much it would cost me to open a repair ticket with OnePlus and let them repair/replace my display unit?
Guess it would cost around 200USD since the display is one of the costliest components in the phone. Not sure if it's only the display issue though. The water might have done some serious damage to the board itself.
100$ easily
My replacement screen cost me 30$ including shipping to Sweden, bought on Aliexpress, top notch quality nothing to complain on quality wise .
Skickat från min ONE A2003 via Tapatalk
pitrus- said:
My replacement screen cost me 30$ including shipping to Sweden, bought on Aliexpress, top notch quality nothing to complain on quality wise .
Skickat från min ONE A2003 via Tapatalk
Click to expand...
Click to collapse
I too considered buying a replacement screen on ebay or aliexpress. But I don't think I feel confident enough to take the necessary steps to replace the screen, because you seem to have to "unglue" the old screen and glue the new screen back on the frame (Sources: https://www.ifixit.com/Guide/OnePlus+2+Screen+Replacement/51922#s115570 and https://youtu.be/Q1b5Ut5kTRM?t=4m).
Is it easier to do than I think? Did you face any issues while replacing it? Can you see or feel a difference with the new screen compared to the original one (i.e. does it perfectly fit into the frame without protruding)?
gnaggwatschn said:
I too considered buying a replacement screen on ebay or aliexpress. But I don't think I feel confident enough to take the necessary steps to replace the screen, because you seem to have to "unglue" the old screen and glue the new screen back on the frame (Sources: https://www.ifixit.com/Guide/OnePlus+2+Screen+Replacement/51922#s115570 and https://youtu.be/Q1b5Ut5kTRM?t=4m).
Is it easier to do than I think? Did you face any issues while replacing it? Can you see or feel a difference with the new screen compared to the original one (i.e. does it perfectly fit into the frame without protruding)?
Click to expand...
Click to collapse
It was pretty straight forward and simple. I just applied heat to screen using a hairdryer and the used the included suction cup to gently loosed the screen from the adhesive using a credit hard to pry away the glue and then removed the connections to the screen and the touch-buttons and home button from the backside and then removed the screen. Then I moved over the home button and touch buttons to the new screen, applied some 3M adhesive strips on the frame after removing the old adhesive, put the screen back in place and reconnected the collectors, pushed the screen in place in the frame and heated it a bit too make sure the adhesive sticks and then screwed everything back in there and put on the back case. Done and done!
Ok I think I am gonny try tro buy a screen on aliexpress and replace it myself. Do you think this one should do?
well maybe you guys can help me out here i did the steps to replace the fingerprint sensor but now my screen wont stay glued , i have not been able to find the glue for the screen anyone can help with that by any chance ?
jera27 said:
well maybe you guys can help me out here i did the steps to replace the fingerprint sensor but now my screen wont stay glued , i have not been able to find the glue for the screen anyone can help with that by any chance ?
Click to expand...
Click to collapse
I would also like to know which kind of "3M adhesive strips" pitrus- used to keep the screen glued.
gnaggwatschn said:
I would also like to know which kind of "3M adhesive strips" pitrus- used to keep the screen glued.
Click to expand...
Click to collapse
I bought this one linked down here
3M Sticker Tape Sticker 1MM Double Side Adhesive For Cellphone Touch Screen LCD
http://s.aliexpress.com/UBbquiQf
(from AliExpress Android)
i will try it thanks how did you apply it ? did you have to do any modifications ? is the phone screen similar to its original state ? did you remove the previous glue ? soo many questions i wish there was a video on how to apply it on the phone , as of now my bottom half of the phone screen is unglued
jera27 said:
i will try it thanks how did you apply it ? did you have to do any modifications ? is the phone screen similar to its original state ? did you remove the previous glue ? soo many questions i wish there was a video on how to apply it on the phone , as of now my bottom half of the phone screen is unglued
Click to expand...
Click to collapse
For me, the old adhesive came off with the old screen. But I did some cleaning with alcohol just to be sure.