Related
Hi,
I've been using my xda for about a month now and have noticed it hard to keep the screen clean, it seems to be very greasy etc... Has anyone invested in a screen protector for this problem or is it not really worth it?
Also cause i have only had mine a month with limited use, has anyone who has owed this phone longer noticed it gets scratched from the pen etc after longer periods of time...?
I know not important questions but just something i've been wondering none the less. Thanks
Got a brando one
I wanted to ditch the case (as it's pants) so I got a brando screen protector. It was a real faff to fit and I still haven't got it a) square or b) without loads of [email protected] under it, but it does its job, it seems to be sensitive enough and I (probably) am too ham-fisted to judge how difficult it is to fit the thing.
Hope that helps.
I've been told the Martin Whatsisname Screen Protectors are really good.
I'm thinking about getting one of these.
Do they leave any marks when you peel them off afterwards? From the glue and stuff?
Hi Tom
They don't use any glue, so you can just peel them off with no problem.
They cling to the screen like clingfilm.
nothing else than brando! have used it on all of my previous devices .. just no comparison to the cheap ones on ebay ...
I would say screen protector is a must for me...I'm too lazy to pull out the stylus every time....a screen protector will allow me to tap with my fingers, nails.....or even a pen....in fact, I put a protector on almost every mobile phones, my previous PPC....
Fair enough, but at £8.50+ its a rip off!!! for a bit of plastic that cost 0.05p to make, they're laughing all the way to the bank....
Supply & Demand
Maybe. It's a quality product and it's still a lot cheaper than a new screen...
You pays yer money.
Maybe but im just not convinced, how can you decribe a bit of platic as a "quality product"? I have heard they are extreemly hard to fit properly without getting finger prints on them etc and you get air bubbles and it is really annoying if you even leave a few specs of dust underneath it...?
No one round the office here seems to bother with them. I dont expect with any device for the screen to remain untouched forever, i think it just comes down to normal wear and tear, as with everything. Just my views anyway, need to hear more about these things before i had over best part of £10.
I have seen a Martin Fields one and someone on here said they were good. Is it easy to notice its there if you have one installed?
I have bought some via ebay from screenprotector24 at £1.99 for 6 plus P&P. There was also a buy 2 get 1 free offer on too. I have never been a fan of screen protectors but I agree that with the Mini-S it is verging on essential.
I am more than happy with the quality of the ones I received.
Hope that helps someone.
Regards,
White.
I've been looking for some on ebay, what did you type in to search and find those? can you link me?
Hi,
Sorry, I'm at work and barred from ebay. www.screenprotector24.de may well work if I recall correctly.
Regards,
White
Brando screen protectors
Just because something's made of plastic doesn't mean it isn't quality. After all look at Pamela Anderson! (Sorry).
The Brando one I got is doing its job. Before I had the screen protector dirt would pile up and I'd be cleaning it 3 or 4 times a day. Now I don't have to. I was worried the screen would get damaged. I don't have to worry what I use on the screen or shoving it in my pocket.
Yes, you can tell it's on if you look. It looks like you've left the manufacturers sheet on but without a tab to remove it if it catches the light. Straight on, you'd be hard pressed to know it's there - honest.
I haven't seen the cheapo ones myself, I went on recomendations on forums from people who had more experience.
Also, Brando service is outstanding in my experience.
Right ok, i am thinking of getting one just for peace of mind. All i can find is Martin Philips ones on UK sites... Where can i find a decent priced Brando one on a UK site for a 02 xdx mini s? Can someone name a shop or link me etc?
Thanks
Go straight to the source!
I bought mine direct from the Brando site in Hong Kong... http://shop.brando.com.hk/screenprotector.php. It arrived within 6 days
I had the antireflective one on my old XDA2, but these ultra glossy ones are MUCH better. It was a fiddle to fit, but I honestly can't that it's there other than by looking for the edge. I've tried this a few times and I find the following procedure works well.
First off, you need to find as dust free an environment as possible. Choose a room that doesn't have any carpet, or fabric in it if you can(cushions curtains etc). Boil a kettle, and make the room a bit steamy. When the steam clears, it should take some of the dust with it.
The trick to avoiding dust is to be prepared. Get a good lint free cloth (lens microfibre cloth worked well for me) and a blower brush - small rubber bulb with a nozzle. Also keep some masking tape ready. Finally you will need a bright light - ideally a spot light, or if you've got low fluorescent lights under over your kitchen work tops, they are ideal. Wear latex gloves if you have any (you can usually get packs of 20 from poundland)
Stick some masking tape to the your worksurface, folding it back on itself, so that the sticky side is facing up. Use several strips so that you have an area two or three times the size of your screen.
Spend a few minutes polishing with the lint free cloth, and then set the phone down, face up, well illuminated (from above) and switched off!. Blow off all the remaining dust with the blower - make sure that no dust is stuck (might require more polishing) at this stage you have two hands free - in a minute you won't! Dont worry if some dust starts to settle back on the screen at this stage - it will be loose, and you can blow it off in a minute.
Next step - take the screen protector, and peel off the backing two thirds of the way. Keep the 'sticky' side face down so dust doesn't settle on it. It's helpful if you can crease the backing slightly as it's quite springy and tends to get in the way a bit. Be careful not to touch the exposed side though. If you're right handed you'll want the screen protector in your right hand at this moment.
The next bit, you might need to repeat a few times until you get it right...
Blow the last bits of dust off the screen (do NOT use your mouth - you will spit all over the screen). Line up the most exposed end of the protector - its a very precise fit, the edges will touch both sides, and the end should be lined up exactly with the end of the screen. If you push the protector under the plastic above the screen it will be short at the other end. You might need to lift and reposition a few times to get this right. Once you have placed the exposed end, put a finger on top and check the alignment. Now check for any dust. You might be able to blow one or two bits off, but if there is more than that, you need to lift off the protector, press it down onto the upturned tape to get rid of any dust, blow the dust of the screen and try again. The dust sticks to the tape MUCH better than the screen, and will not leave any residue on the Brando protector, so you can do this quite a few times if necessary.
The important thing here is not to panic. You will get dust, and will need to go round the loop a few times, but as you'll be prepared, there will be no problem. Once the protector is lined up, the screen is (temporarily) dust free and there are no bubbles (phew!) carefully remove the last of the backing film and holding the edges very lightly between your fingers (gloves help here) lay the last bit removing any bubbles. Once down, it is hard to get the protector off without damaging the edge so only do the last bit once you're sure there is no dust/bubbles.
Remove the front sheet and polish. With any luck, you should hardly be able to tell that the screen protector is there!
Thanks for those really comprehensive instructions! I'm going to order one from the Brando site today and will pick up the blower and lint-free cloth etc from Jessops (camera shop) this weekend.
Martin Fields overlay plus Question
Nice one on such detailed instructions!
I order a Martin Fields over lay plus today, they seem to have good reviews everywhere i have looked. They are slightly adhesive though, but as this is a "gentle silicon based glue" (so i hear) i think that means it will be fine on the screen.
Has anyone had experience on using these and what the screen is like after you remove them, any residue etc left afterwards? How long will it last roughly?
Thanks for any help guys!
I haven't tried this, but you could probably save yourself the cost of a blower brush by using a bike pump or better still an airbed footpump (you can use that one handed).
tom99, if you get a Martin Fields protector (or any other sort that uses adhesive) I'm not sure that its safe to use masking tape to clean it. The Brando ones stick to the screen electostatically, so its safe to clean them with tape (the instructions that come with it recommend scotch tape). If the instructions you get with your Martin Fields protector don't mention cleaning with tape, then I would miss out that step. Can you add a comment to this thread when you get it (or anyone else that has used a MF protector)? It might help others decide which protector to go for.
Can someone please tell me how to apply the screen protector that comes with the phone as it's just a large piece of clear plastic with no instructions how to physically attach it to the display!
It has a peel away backing which is much thinner than the protector.
I struggled to find how this attached when I got mine and have since put hair and smudges on the sticky backing. Can't wait for the new ones to come online mid May.
It's a sticker that you stick on the screen. How hard is this?!
Just put it on. Work cleanly though, be prepared and do it right the first time.
Bend the corner of the big part slightly and the two parts seperate
The part that goes onto the backing bit is what goes on screen
start from the top and smooth it down
As mentioned, work in a clean/dust free environment!
I've done it many times but even this time round, I got fluff inside - just one spec thinking as it was brand new out of the box, it wouldnt have anything on the screen and so I wouldnt need to clean it !
In removing the protector to clean it out... I ruined it
Got my new Brando one the other day which feels a bit more stronger and durable but still clear so I'll be putting that on later tonight
And now I have a air can with me too so if I get anything in the way, I can blow it out rather than trying to scrape it out
I've now put on the screen protector that came with the phone, but it feels a little thin and flimsy.
I'd like to know people's opinion of other aftermarket brands of protector for this phone as I'd like to get something a bit better quality.
Same thoughts here too
I ordered a pair from HTC direct but I think looking at them now that I have them, they are the same as the originals so I will probably not bother using them
I also have the Brando version now - Not opened yet but I will open and apply it to my phone tomorrow evening - just need a dust-free environment to test it
Apparently, Brando boast they have the best protectors so lets see
It does feel a lot stronger than the original
akash_84 said:
Same thoughts here too
I ordered a pair from HTC direct but I think looking at them now that I have them, they are the same as the originals so I will probably not bother using them
I also have the Brando version now - Not opened yet but I will open and apply it to my phone tomorrow evening - just need a dust-free environment to test it
Apparently, Brando boast they have the best protectors so lets see
It does feel a lot stronger than the original
Click to expand...
Click to collapse
Did you try this new Brando screen protector, and if so, is it any good?
Also, has anyone else had any experience of after-market screen protectors for this phone?
OK I applied mine today - sorry for the delay but I was just waiting for a time I could be patient !
I ordered it from HTCDirect as they are the only ones that had in stock
Recieved it promptly the next day so Kudos to them on that...also the guy I kept in touch with over email (Carlos if I remember correctly) was great and prompt in my queries.
My main query was - does it have the SAME fitment as the original bundled one.
As you know, the bundled one covers the entire screen including the slider for zoom and camera
The answer was Yes, it was exactly the same fitment.
So when I opened the pack, I was a bit annoyed as it was clearly NOT the same fitment! It's close however, but the top of the camera where on the HTC is all the way round with a small hole for the camera, the Brando one is in a U shape leaving the top bit of the camera open.
OK onto application
Just like all Brando protectors, it is protected by two covers on either end with clear instructions - pull one side BEFORE application and the other AFTER application
Once the dust was off the screen and the original protector...
I did just this - and after several attempts of lining it up - and I note, it is very EXACT in lining up. Slightly out and you will have more black on one side from the screen than the other.
Peeled it off, applied it and smoothed it out - the latter bit was hardly needed as the bubbles just vanished which was great.
At this state, the protector looked smoked a little and not as clear as the original one.
Once I was happy, I peeled the top part - noticed one bubble near the end where the label to peel was, smoothed it out and the protector was as clear as the original one.
First impressions:
It does feel MUCH more durable
It has a very slight and I mean SLIGHT smoked affect in that it is not 100% transparent as the original one but this shows how good it is potentially in strength.
Usage is fine, I can glide over it with my finger and stylus without any issues. The original was a finger print magnet but this seems to not stain with it which is great.
Now the downside....
I think HTCDirect sent me a slightly duff one. It has clearly got markings on the top (once the top layer was off) which look like impact marks.
It is very tiny - almost like what happens to a screen without a protector after 12months
I'm not too fussed but feel a bit cheated. Its no use removing it now as I would have no protector on it during the replacement stages - not to metion I would have to pay to ship back etc.
For now, I am ok with it but if it bugs me, I will throw it away and put the original one on (I ordered 2 extras from Clove who as usual, got it to me instantly, good communications and speed in delivery).
The clove one has no marks at all so thats an option.
Hope this answers some of your questions but to summarise your question
Is it stronger?
Yes it is
Is it worth it?
If you can get one mark free - yes it is
Benefits?
It's re-usable, stronger, washable, and I notice it does not let as much light reflect of it - something I had huge problems with in the sunlight with the original one where I could not see the screen - I am not exaggerating!
Downsides?
Where I got mine from, it has marks on it - something that might just force me to remove it and go back to the original one
Also the camera does not go in a O shape but rather a U shape
OK during the submit button, I realsed the marks and the U shape was bugging me too much
I knew it was a matter of time that gap in the U would get clogged up with dust that would eventually get stuck around the U bit
Removed it and applied the original one I bought from Clove... I have two so if it does wear down, I can replace it
I know from experiance that the original one in the box that I applied lasted fine up till now (a month now since I've had my TD2) so I dont doubt that it will be worn out - May not last as long as Brando's guarantee of it outlasting te device but that's fine given the price of the HTC ones.
Applied it without any dust getting trapped (the main reason I had to buy these and the brando one)
I found those marks were actually dust that was already stuck under the protective layer - whether this is HTCDirects fault or Brando during factory release - who knows but I think as a lesson, I'm staying away from both and sticking to the original stuff.
Hope you make the right decision either way - for now, a brando goes into the bin
akash_84 said:
Bend the corner of the big part slightly and the two parts seperate
The part that goes onto the backing bit is what goes on screen
start from the top and smooth it down
As mentioned, work in a clean/dust free environment!
I've done it many times but even this time round, I got fluff inside - just one spec thinking as it was brand new out of the box, it wouldnt have anything on the screen and so I wouldnt need to clean it !
In removing the protector to clean it out... I ruined it
Got my new Brando one the other day which feels a bit more stronger and durable but still clear so I'll be putting that on later tonight
And now I have a air can with me too so if I get anything in the way, I can blow it out rather than trying to scrape it out
Click to expand...
Click to collapse
damnit, didn't pay enough attention to dust & co...so after i saw that i catched a few dust pieces under it, i've tried to get them out manually - big mistake.
so trashed the original one and waiting for the new brando to put it on. being a former iphone-user, i must admit that the diamond2 screen is pretty sensible to scratches. i thought that i won't be needing any protection, but i already have a few small ones...so a screen protection is a must-have now.
Should have read this first
I should have read this thread before I tried to apply my screen protector. Straight away I had dust underneath the screen protector. Obviously I will now have to order some more protectors but will I be alright using my phone until they arrive? How delicate is the td2 screen?
You'll be fine using it while its there - just be annoying to see the dust specs!
I ordered a pair of the original ones in the end as I was not happy at all with the premium Brando one - the look, feel and visibility was terrible
Reason I ordered 2 of the original ones is I was hearing rumours before the unit was even released that the original HTC one was not durable and would need to be replaced after x amount of months - having had mine for 4-5 months now and with heavy usage, I can report back to say the first protector of the two is still on there - still very clean with no stylus/finger/nail marks and still as durable as it was when I put it first on.
arsenal84 said:
I should have read this thread before I tried to apply my screen protector. Straight away I had dust underneath the screen protector. Obviously I will now have to order some more protectors but will I be alright using my phone until they arrive? How delicate is the td2 screen?
Click to expand...
Click to collapse
From what other threads are saying the screen should be treated with care. Don't push it hard and avoid impacts. Don't stick the phone in your back pocket! Some people have experienced damaged screens even after a short time.
Shouldnt put any phone in your back pocket!
The number of phones I have to fix or write off because they have had severe pressure on them - ie: sitting on them has increased 5 fold recently.
And lets face it...the countries population are not getting any thinner/smaller!
eXelero said:
damnit, didn't pay enough attention to dust & co...so after i saw that i catched a few dust pieces under it, i've tried to get them out manually
Click to expand...
Click to collapse
I know it is not recommended. but I use a small drop of water on the screen before applying the screen, wiping the water as it is squeeze out. The water takes the dust with it.
Hi
I've applied mine that came with the Diamond 2 and after a few attempts you can't see it is there. Ironically I fits so well I almost want to put another screen protector on top of it so it doesn't become damaged and need replacing.
Anyway a tip. Working in a dust free environment is the key. A bathroom is a good place. I have a hepa air filter (for hayfever) and this removes dust really well so run that for a bit which helps.
With all the care in the world dust can get underneath, I had a few specs, and they tend to cause a small bubble as the screen screen protector can't fit flush. I found it very easy to remove them. Have some sticky tape handy, this can be used to lift up the screen protector from the corner. Lift it back up enough to get to the spec of dust, and using another piece of sticky tape dab the spec of dust off the sticky side of the protector, then lay it back down.
Regards
Phil
Hairs
Fru T Bunn said:
It has a peel away backing which is much thinner than the protector.
I struggled to find how this attached when I got mine and have since put hair and smudges on the sticky backing. Can't wait for the new ones to come online mid May.
Click to expand...
Click to collapse
I know what you mean I made an okay job of the one that came with it. The rubber case I bought of eBay came with one as well and made a right pigs ear of that. I think they need to be applied in a clean room
I've since bought some more off eBay so next time, I'm going to be a lot more careful!
Cheers, Rob.
I got 3 screen protectors with the original phone (2 of them as a gift). The first one was perfect except for a piece of fluff near the middle of the screen. I tried to remove it with a cloth(!!!) and ruined it. So I went for the second one, but at this stage the screen was not clean so I tried to use a microfibre cloth, which made it worse because it leaves even more fluff. I tried to fix it a few times and so now I have fluff inside, plus a bubble (the protector is a bit scratched) plus it doesn't stick properly on most of the sides and around the holes.
I am tempted to use the last one, but if I ruin it once more I am out of them. My biggest problem is how to clean the screen before sticking the protector. Will all the fluff come away when I remove the old protector? How can I clean the screen, knowing that the microfibre leaves fluff? Shall I blow with a can of compressed air?
I find magic tape is great for removing dust spots. Use the backing sheet to gently lift a corner then push the tape underneath to clean screen or protector as needed.
My favourite screen protectors are from Martin Fields. Really tough and easy to apply. Also, they are washable so if you do get a real dust problem you just take it off an run under the tap. Don't try that with the phone though...
So! Back in December 2010, I ordered a Zagg Invisible Shield for my significant other. It arrived in time for Christmas.
We noticed on the protector, before installation, while it was still on the original packaging sheet, there was orange peel, (for those who don't know, orange peel is a surface that looks and somewhat feels like the texture of an actual orange; small bumps.) There was also outlines on the front, to what looks like something heavy was set on the sheet either when it was manufactured, or packaged.
On top of that, there were in-prints of lines going across the protector, A 'square-shaped' in-print, from what looks like the same shape and size of either the solution bottle that it comes with, or the SKU SONERCX2FB sticker that they might stamp on the plastic bag while the protector is 'hot-off-the-press.
We were hoping once it was placed on the phone, it would smooth out, and go away... IT STAYED THERE.
It bugged him, there was rainbow effects, you can see the annoying inprints clearly while the screen is in use. THE SCREEN VIEW IS DISTORTED. Tilt the phone towards the right lighting, and you can still see them.
The protector isn't really smooth, it is soft, it does grab the stylus/nail. Creates a drag.
We made sure it cured for a day before using, to make sure the skin dries and adheres to the phone.
Its been couple months, and dirt has already found its way in the corners, started peeling, and has somewhat changed its color to being less clear.
GUESS WHAT? I decided to order another one in early February 2011, because I didn't want his new phone unprotected. I don't have patience for the exchange time period.
The new protector arrives. AND GUESS WHAT AGAIN??? IT'S THE SAME CONDITION AS THE FIRST ONE I ORDERED!! It had orange peel and line in print across the screen! Perfect 'square-shaped' in-prints! I didn't even bother to put it on.
STAY AWAY FROM INVISIBLESHIELD. I do not recommend this company AT ALL. Waste of money! Don't except anything better that GARBAGE.
Try Martin Field. http://www.martinfields.com/US/Print/MFOP-SEXperiaX2/en
Thanks for listening to my rant.
If course the pictures don't do justice, I tried.
I'm a Xperia X1i user, I recommend Shinomi (from Amazon.com) It pretty much covers the entire phone! (Camera lens, the sides, literally top and bottom of the phone.) Takes a while to install, but worth it.
Hi all,
Got my UK TF101 today and loving it.
However the finish is not that good. The small plastic strip between the glass and the bronze edge of the casing has remnants of the glue used during the assembly and it won't come off. Looks like it has been rush assembled and makes it look tatty. Would be a shame to return it just for that but when you spend this money and see what finish iPads have you really want it to be mint.
Does any one else have this problem on their TF101?
Unless they have changed the manufacturing process for newer devices, there's no glue anywhere near the casing/bezel.
I have some glue on the top of the black strip on the top-left (when holding the tablet in landscape mode). I only noticed it when I had my desk lamp shining on it. It wasn't present on the other TF I had at the moment. Doesn't really bother me that much.
Yeah, mine arrived today and has the same thing. The rubber's not quite flush with the screen and its mount, but it really doesn't matter.
Overall very impressed with the device so far. I certainly won't be sending it back over that small defect. We live in an imperfect world..!
Yup. But eventually after some use it wore off.
Mine just arrived today I can see some remnants of what appears to be glue both bottom & left side. Also it appears that the 1/2 section on the rubber on the right side has been rubbed down.
Quite agree it won't affect the use of the device but when you see how sharp a finish the iPad has it is a shame to not be perfect on the TF101.
I called Comet and they were happy to do a swap. When I popped in to the local store the Customer Service Desk chap admitted I was the third person with this problem. He got another one from stock and it was better but still a bit of dried glue. He offered an exchange or 10% refund. I decided to go with the 10% refund so got £43 back. I can now live with the problem.
If others want to see what we are on about here is a pic of my bezel. Right hand side is as I would expect but the top strip is very messy and slightly raised compared to the flush fitting section.
aerotec said:
If others want to see what we are on about here is a pic of my bezel. Right hand side is as I would expect but the top strip is very messy and slightly raised compared to the flush fitting section.
Click to expand...
Click to collapse
Thx for the pic, it's good to see what you were describing. I've looked really closely at my device and I still cant see any glue on mine. It looks like the manufacturing process has changed since they started production, not for the better in this case it seems. That certainly is a fair amount of money off though.
Had glue on mine too, I thought it had been refurbed and returned it for another unit. This one was checked in store and appears perfect.
So i did this with 3m 1080 scotchprint carbon series and with nail scissors cutting it from 10x20cm took a while, about 2 hours to get it look nice i also cut a piece for the home button which took awhile too to get it fit perfectly!
to make this thread not so useless, recommend or post pictures of your customized gs2
anyway, what do you think ?
Looks excellent mate, would love a tutorial wouldn't mind that look myself.
Very nice...
Sent from my SGH-T959V using XDA App
Nice, I have a Samsung mesh case on mine which would cover that off
Does it say 0.8 MP?
That looks really nice, shame your not selling them
Its 0.8 because is on mirror ( 0.8 | 8.0 )
cost of this project was about 10-20 bucks. really, its not that difficult to make, just needs patience and good light. that is the first one i've ever made!
@itehappy most definitely hope its not a 0.8mp unit anyway nice to see people here from i8910 community!
Thanks for the prompt... Just ordered a sheet of 1200 x 300 for under $AUS 10 .
What did you cut it with? Just a normal sharp knife/razor blade? Any tips on cutting the corners, makig the holes, putting the sides and corners on etc???
I know it doesn't require a huge 20 page instruction book but if you could provide some tips or suggestions I think that would be great... Unless you plan on selling them then I suggest not to give the tips
Edit: Just realised you only did the back cover and not the edges... Maybe I will report back when I finally get my sheet and start cutting.
Nice! Tutorial would be appreciated!
When I read the thread title I imagined it would look tacky, but it actually looks really good
Nice. If you want to make some to sell I will buy.
I have a Silver one and you buy them online... o.o
looks great dude, what's the texture of the tape like though? The phone is slippy enough with the stock cover, with smooth tape it must be worse!
i want this too! Looks very nice!
Sent from my GT-I9100 using XDA App
+1 for you making them and selling them. (I don't have the patience)
viva.fidel said:
looks great dude, what's the texture of the tape like though? The phone is slippy enough with the stock cover, with smooth tape it must be worse!
Click to expand...
Click to collapse
It's actually textured, the "weave" is bumpy, raised a few cm, provides a bit of a rough, oil free surface without being uncomfortable. And you can do a fun DJ scratching imitation if you run your fingernail over it quickly.
I've been using it (they call it 3M Dynoc in North America) on the back of my SGS1 for over a year now, and on the back of my Tab 7" for nearly as long.
I couldn't be arsed to cut my own, so I bought mine pre-cut from PhantomSkinz (Skinomi also sells a very similar "skin"). The phone kit costs ~$25 before coupon, and it covers the entire back, the sides, and even comes with a wet-apply screen protector.
It's dead easy to apply, though the edges take a bit of practice...but if you screw up, just lift it up and try again.
It's durable as hell, the SGS1 has one minor, nearly invisible scratch in it after a year of abuse in my pocket, in my motorcycle jacket or tank bag, dirty tables, etc. They look far more "high tech" than the funky designs Samsung used on the back of those devices, especially the Tab.
Occasionally, I'd catch the bottom edge of the tape on the SGS with my fingernail when removing the battery cover and it'll lift a bit. Apply some heat and it goes right back into shape.
Little trick with the rough feel on the edges...heat it (desk lamp or hair dryer both work well) and run your fingernail over the edge...this thins it, making it much smoother.
I just placed an order with Skinomi for both a SGS2 and Galaxy Tab 10.1 "carbon" kit. On the SGS2, I'm thinking about leaving the battery cover naked since it's cheap to replace and already textured, and just using the carbon on the chin and sides. The chin on mine is starting to show some friction wear along the edge closest to the battery cover, and the sides get slippery as a bar of soap.
pbrown77 said:
Thanks for the prompt... Just ordered a sheet of 1200 x 300 for under $AUS 10 .
What did you cut it with? Just a normal sharp knife/razor blade? Any tips on cutting the corners, makig the holes, putting the sides and corners on etc???
I know it doesn't require a huge 20 page instruction book but if you could provide some tips or suggestions I think that would be great... Unless you plan on selling them then I suggest not to give the tips
Edit: Just realised you only did the back cover and not the edges... Maybe I will report back when I finally get my sheet and start cutting.
Click to expand...
Click to collapse
wait wait whaaat? 1200x300 for $10 dollars??!? is it 3M 1080 series or 3M Di-noc?
i cut all this with little scissors, about the length of a palm, maybe just a bit more. corners wont need any special stuff, just a hair dryer to get it a little more flexible. ONE THING, when i bought the carbon, I tought that i'll just bend anything which comes over the edge, to backside of the plate. well its not that easy. gs2 cover is so precisely cut that it doesnt allow any kind of extra stuff under the cover, so you just need to cut it little bit at a time, then try it, and cut a bit more and try, untill it fits properly. this will take most of the installation time. just be careful not to cut too much! same goes for the camera hole. very carefully and take the time it needs, even if there is 0.1mm too much, the camera wont fit properly. not difficult, but takes time. a hour atleast.
meh, im a nice guy, i'll give all the tips needed
@viva.fidel
the surface of the new 3M 1080 series has more rubbery feel than the Di-noc (what skinomi uses) and there is seriously good grip! Doesn't feel sticky, but still offers awesome grip believe me! maybe because of the carbon texture i dont know but has good grip for sure!
sorry if theres typos, wrote whole message with GS2 in PORTRAIT mode
Hi, If you were to sell any, I would buy one, It look really nice
ignore now!