Can someone please tell me how to apply the screen protector that comes with the phone as it's just a large piece of clear plastic with no instructions how to physically attach it to the display!
It has a peel away backing which is much thinner than the protector.
I struggled to find how this attached when I got mine and have since put hair and smudges on the sticky backing. Can't wait for the new ones to come online mid May.
It's a sticker that you stick on the screen. How hard is this?!
Just put it on. Work cleanly though, be prepared and do it right the first time.
Bend the corner of the big part slightly and the two parts seperate
The part that goes onto the backing bit is what goes on screen
start from the top and smooth it down
As mentioned, work in a clean/dust free environment!
I've done it many times but even this time round, I got fluff inside - just one spec thinking as it was brand new out of the box, it wouldnt have anything on the screen and so I wouldnt need to clean it !
In removing the protector to clean it out... I ruined it
Got my new Brando one the other day which feels a bit more stronger and durable but still clear so I'll be putting that on later tonight
And now I have a air can with me too so if I get anything in the way, I can blow it out rather than trying to scrape it out
I've now put on the screen protector that came with the phone, but it feels a little thin and flimsy.
I'd like to know people's opinion of other aftermarket brands of protector for this phone as I'd like to get something a bit better quality.
Same thoughts here too
I ordered a pair from HTC direct but I think looking at them now that I have them, they are the same as the originals so I will probably not bother using them
I also have the Brando version now - Not opened yet but I will open and apply it to my phone tomorrow evening - just need a dust-free environment to test it
Apparently, Brando boast they have the best protectors so lets see
It does feel a lot stronger than the original
akash_84 said:
Same thoughts here too
I ordered a pair from HTC direct but I think looking at them now that I have them, they are the same as the originals so I will probably not bother using them
I also have the Brando version now - Not opened yet but I will open and apply it to my phone tomorrow evening - just need a dust-free environment to test it
Apparently, Brando boast they have the best protectors so lets see
It does feel a lot stronger than the original
Click to expand...
Click to collapse
Did you try this new Brando screen protector, and if so, is it any good?
Also, has anyone else had any experience of after-market screen protectors for this phone?
OK I applied mine today - sorry for the delay but I was just waiting for a time I could be patient !
I ordered it from HTCDirect as they are the only ones that had in stock
Recieved it promptly the next day so Kudos to them on that...also the guy I kept in touch with over email (Carlos if I remember correctly) was great and prompt in my queries.
My main query was - does it have the SAME fitment as the original bundled one.
As you know, the bundled one covers the entire screen including the slider for zoom and camera
The answer was Yes, it was exactly the same fitment.
So when I opened the pack, I was a bit annoyed as it was clearly NOT the same fitment! It's close however, but the top of the camera where on the HTC is all the way round with a small hole for the camera, the Brando one is in a U shape leaving the top bit of the camera open.
OK onto application
Just like all Brando protectors, it is protected by two covers on either end with clear instructions - pull one side BEFORE application and the other AFTER application
Once the dust was off the screen and the original protector...
I did just this - and after several attempts of lining it up - and I note, it is very EXACT in lining up. Slightly out and you will have more black on one side from the screen than the other.
Peeled it off, applied it and smoothed it out - the latter bit was hardly needed as the bubbles just vanished which was great.
At this state, the protector looked smoked a little and not as clear as the original one.
Once I was happy, I peeled the top part - noticed one bubble near the end where the label to peel was, smoothed it out and the protector was as clear as the original one.
First impressions:
It does feel MUCH more durable
It has a very slight and I mean SLIGHT smoked affect in that it is not 100% transparent as the original one but this shows how good it is potentially in strength.
Usage is fine, I can glide over it with my finger and stylus without any issues. The original was a finger print magnet but this seems to not stain with it which is great.
Now the downside....
I think HTCDirect sent me a slightly duff one. It has clearly got markings on the top (once the top layer was off) which look like impact marks.
It is very tiny - almost like what happens to a screen without a protector after 12months
I'm not too fussed but feel a bit cheated. Its no use removing it now as I would have no protector on it during the replacement stages - not to metion I would have to pay to ship back etc.
For now, I am ok with it but if it bugs me, I will throw it away and put the original one on (I ordered 2 extras from Clove who as usual, got it to me instantly, good communications and speed in delivery).
The clove one has no marks at all so thats an option.
Hope this answers some of your questions but to summarise your question
Is it stronger?
Yes it is
Is it worth it?
If you can get one mark free - yes it is
Benefits?
It's re-usable, stronger, washable, and I notice it does not let as much light reflect of it - something I had huge problems with in the sunlight with the original one where I could not see the screen - I am not exaggerating!
Downsides?
Where I got mine from, it has marks on it - something that might just force me to remove it and go back to the original one
Also the camera does not go in a O shape but rather a U shape
OK during the submit button, I realsed the marks and the U shape was bugging me too much
I knew it was a matter of time that gap in the U would get clogged up with dust that would eventually get stuck around the U bit
Removed it and applied the original one I bought from Clove... I have two so if it does wear down, I can replace it
I know from experiance that the original one in the box that I applied lasted fine up till now (a month now since I've had my TD2) so I dont doubt that it will be worn out - May not last as long as Brando's guarantee of it outlasting te device but that's fine given the price of the HTC ones.
Applied it without any dust getting trapped (the main reason I had to buy these and the brando one)
I found those marks were actually dust that was already stuck under the protective layer - whether this is HTCDirects fault or Brando during factory release - who knows but I think as a lesson, I'm staying away from both and sticking to the original stuff.
Hope you make the right decision either way - for now, a brando goes into the bin
akash_84 said:
Bend the corner of the big part slightly and the two parts seperate
The part that goes onto the backing bit is what goes on screen
start from the top and smooth it down
As mentioned, work in a clean/dust free environment!
I've done it many times but even this time round, I got fluff inside - just one spec thinking as it was brand new out of the box, it wouldnt have anything on the screen and so I wouldnt need to clean it !
In removing the protector to clean it out... I ruined it
Got my new Brando one the other day which feels a bit more stronger and durable but still clear so I'll be putting that on later tonight
And now I have a air can with me too so if I get anything in the way, I can blow it out rather than trying to scrape it out
Click to expand...
Click to collapse
damnit, didn't pay enough attention to dust & co...so after i saw that i catched a few dust pieces under it, i've tried to get them out manually - big mistake.
so trashed the original one and waiting for the new brando to put it on. being a former iphone-user, i must admit that the diamond2 screen is pretty sensible to scratches. i thought that i won't be needing any protection, but i already have a few small ones...so a screen protection is a must-have now.
Should have read this first
I should have read this thread before I tried to apply my screen protector. Straight away I had dust underneath the screen protector. Obviously I will now have to order some more protectors but will I be alright using my phone until they arrive? How delicate is the td2 screen?
You'll be fine using it while its there - just be annoying to see the dust specs!
I ordered a pair of the original ones in the end as I was not happy at all with the premium Brando one - the look, feel and visibility was terrible
Reason I ordered 2 of the original ones is I was hearing rumours before the unit was even released that the original HTC one was not durable and would need to be replaced after x amount of months - having had mine for 4-5 months now and with heavy usage, I can report back to say the first protector of the two is still on there - still very clean with no stylus/finger/nail marks and still as durable as it was when I put it first on.
arsenal84 said:
I should have read this thread before I tried to apply my screen protector. Straight away I had dust underneath the screen protector. Obviously I will now have to order some more protectors but will I be alright using my phone until they arrive? How delicate is the td2 screen?
Click to expand...
Click to collapse
From what other threads are saying the screen should be treated with care. Don't push it hard and avoid impacts. Don't stick the phone in your back pocket! Some people have experienced damaged screens even after a short time.
Shouldnt put any phone in your back pocket!
The number of phones I have to fix or write off because they have had severe pressure on them - ie: sitting on them has increased 5 fold recently.
And lets face it...the countries population are not getting any thinner/smaller!
eXelero said:
damnit, didn't pay enough attention to dust & co...so after i saw that i catched a few dust pieces under it, i've tried to get them out manually
Click to expand...
Click to collapse
I know it is not recommended. but I use a small drop of water on the screen before applying the screen, wiping the water as it is squeeze out. The water takes the dust with it.
Hi
I've applied mine that came with the Diamond 2 and after a few attempts you can't see it is there. Ironically I fits so well I almost want to put another screen protector on top of it so it doesn't become damaged and need replacing.
Anyway a tip. Working in a dust free environment is the key. A bathroom is a good place. I have a hepa air filter (for hayfever) and this removes dust really well so run that for a bit which helps.
With all the care in the world dust can get underneath, I had a few specs, and they tend to cause a small bubble as the screen screen protector can't fit flush. I found it very easy to remove them. Have some sticky tape handy, this can be used to lift up the screen protector from the corner. Lift it back up enough to get to the spec of dust, and using another piece of sticky tape dab the spec of dust off the sticky side of the protector, then lay it back down.
Regards
Phil
Hairs
Fru T Bunn said:
It has a peel away backing which is much thinner than the protector.
I struggled to find how this attached when I got mine and have since put hair and smudges on the sticky backing. Can't wait for the new ones to come online mid May.
Click to expand...
Click to collapse
I know what you mean I made an okay job of the one that came with it. The rubber case I bought of eBay came with one as well and made a right pigs ear of that. I think they need to be applied in a clean room
I've since bought some more off eBay so next time, I'm going to be a lot more careful!
Cheers, Rob.
I got 3 screen protectors with the original phone (2 of them as a gift). The first one was perfect except for a piece of fluff near the middle of the screen. I tried to remove it with a cloth(!!!) and ruined it. So I went for the second one, but at this stage the screen was not clean so I tried to use a microfibre cloth, which made it worse because it leaves even more fluff. I tried to fix it a few times and so now I have fluff inside, plus a bubble (the protector is a bit scratched) plus it doesn't stick properly on most of the sides and around the holes.
I am tempted to use the last one, but if I ruin it once more I am out of them. My biggest problem is how to clean the screen before sticking the protector. Will all the fluff come away when I remove the old protector? How can I clean the screen, knowing that the microfibre leaves fluff? Shall I blow with a can of compressed air?
I find magic tape is great for removing dust spots. Use the backing sheet to gently lift a corner then push the tape underneath to clean screen or protector as needed.
My favourite screen protectors are from Martin Fields. Really tough and easy to apply. Also, they are washable so if you do get a real dust problem you just take it off an run under the tap. Don't try that with the phone though...
Related
Hi,
I've been using my xda for about a month now and have noticed it hard to keep the screen clean, it seems to be very greasy etc... Has anyone invested in a screen protector for this problem or is it not really worth it?
Also cause i have only had mine a month with limited use, has anyone who has owed this phone longer noticed it gets scratched from the pen etc after longer periods of time...?
I know not important questions but just something i've been wondering none the less. Thanks
Got a brando one
I wanted to ditch the case (as it's pants) so I got a brando screen protector. It was a real faff to fit and I still haven't got it a) square or b) without loads of [email protected] under it, but it does its job, it seems to be sensitive enough and I (probably) am too ham-fisted to judge how difficult it is to fit the thing.
Hope that helps.
I've been told the Martin Whatsisname Screen Protectors are really good.
I'm thinking about getting one of these.
Do they leave any marks when you peel them off afterwards? From the glue and stuff?
Hi Tom
They don't use any glue, so you can just peel them off with no problem.
They cling to the screen like clingfilm.
nothing else than brando! have used it on all of my previous devices .. just no comparison to the cheap ones on ebay ...
I would say screen protector is a must for me...I'm too lazy to pull out the stylus every time....a screen protector will allow me to tap with my fingers, nails.....or even a pen....in fact, I put a protector on almost every mobile phones, my previous PPC....
Fair enough, but at £8.50+ its a rip off!!! for a bit of plastic that cost 0.05p to make, they're laughing all the way to the bank....
Supply & Demand
Maybe. It's a quality product and it's still a lot cheaper than a new screen...
You pays yer money.
Maybe but im just not convinced, how can you decribe a bit of platic as a "quality product"? I have heard they are extreemly hard to fit properly without getting finger prints on them etc and you get air bubbles and it is really annoying if you even leave a few specs of dust underneath it...?
No one round the office here seems to bother with them. I dont expect with any device for the screen to remain untouched forever, i think it just comes down to normal wear and tear, as with everything. Just my views anyway, need to hear more about these things before i had over best part of £10.
I have seen a Martin Fields one and someone on here said they were good. Is it easy to notice its there if you have one installed?
I have bought some via ebay from screenprotector24 at £1.99 for 6 plus P&P. There was also a buy 2 get 1 free offer on too. I have never been a fan of screen protectors but I agree that with the Mini-S it is verging on essential.
I am more than happy with the quality of the ones I received.
Hope that helps someone.
Regards,
White.
I've been looking for some on ebay, what did you type in to search and find those? can you link me?
Hi,
Sorry, I'm at work and barred from ebay. www.screenprotector24.de may well work if I recall correctly.
Regards,
White
Brando screen protectors
Just because something's made of plastic doesn't mean it isn't quality. After all look at Pamela Anderson! (Sorry).
The Brando one I got is doing its job. Before I had the screen protector dirt would pile up and I'd be cleaning it 3 or 4 times a day. Now I don't have to. I was worried the screen would get damaged. I don't have to worry what I use on the screen or shoving it in my pocket.
Yes, you can tell it's on if you look. It looks like you've left the manufacturers sheet on but without a tab to remove it if it catches the light. Straight on, you'd be hard pressed to know it's there - honest.
I haven't seen the cheapo ones myself, I went on recomendations on forums from people who had more experience.
Also, Brando service is outstanding in my experience.
Right ok, i am thinking of getting one just for peace of mind. All i can find is Martin Philips ones on UK sites... Where can i find a decent priced Brando one on a UK site for a 02 xdx mini s? Can someone name a shop or link me etc?
Thanks
Go straight to the source!
I bought mine direct from the Brando site in Hong Kong... http://shop.brando.com.hk/screenprotector.php. It arrived within 6 days
I had the antireflective one on my old XDA2, but these ultra glossy ones are MUCH better. It was a fiddle to fit, but I honestly can't that it's there other than by looking for the edge. I've tried this a few times and I find the following procedure works well.
First off, you need to find as dust free an environment as possible. Choose a room that doesn't have any carpet, or fabric in it if you can(cushions curtains etc). Boil a kettle, and make the room a bit steamy. When the steam clears, it should take some of the dust with it.
The trick to avoiding dust is to be prepared. Get a good lint free cloth (lens microfibre cloth worked well for me) and a blower brush - small rubber bulb with a nozzle. Also keep some masking tape ready. Finally you will need a bright light - ideally a spot light, or if you've got low fluorescent lights under over your kitchen work tops, they are ideal. Wear latex gloves if you have any (you can usually get packs of 20 from poundland)
Stick some masking tape to the your worksurface, folding it back on itself, so that the sticky side is facing up. Use several strips so that you have an area two or three times the size of your screen.
Spend a few minutes polishing with the lint free cloth, and then set the phone down, face up, well illuminated (from above) and switched off!. Blow off all the remaining dust with the blower - make sure that no dust is stuck (might require more polishing) at this stage you have two hands free - in a minute you won't! Dont worry if some dust starts to settle back on the screen at this stage - it will be loose, and you can blow it off in a minute.
Next step - take the screen protector, and peel off the backing two thirds of the way. Keep the 'sticky' side face down so dust doesn't settle on it. It's helpful if you can crease the backing slightly as it's quite springy and tends to get in the way a bit. Be careful not to touch the exposed side though. If you're right handed you'll want the screen protector in your right hand at this moment.
The next bit, you might need to repeat a few times until you get it right...
Blow the last bits of dust off the screen (do NOT use your mouth - you will spit all over the screen). Line up the most exposed end of the protector - its a very precise fit, the edges will touch both sides, and the end should be lined up exactly with the end of the screen. If you push the protector under the plastic above the screen it will be short at the other end. You might need to lift and reposition a few times to get this right. Once you have placed the exposed end, put a finger on top and check the alignment. Now check for any dust. You might be able to blow one or two bits off, but if there is more than that, you need to lift off the protector, press it down onto the upturned tape to get rid of any dust, blow the dust of the screen and try again. The dust sticks to the tape MUCH better than the screen, and will not leave any residue on the Brando protector, so you can do this quite a few times if necessary.
The important thing here is not to panic. You will get dust, and will need to go round the loop a few times, but as you'll be prepared, there will be no problem. Once the protector is lined up, the screen is (temporarily) dust free and there are no bubbles (phew!) carefully remove the last of the backing film and holding the edges very lightly between your fingers (gloves help here) lay the last bit removing any bubbles. Once down, it is hard to get the protector off without damaging the edge so only do the last bit once you're sure there is no dust/bubbles.
Remove the front sheet and polish. With any luck, you should hardly be able to tell that the screen protector is there!
Thanks for those really comprehensive instructions! I'm going to order one from the Brando site today and will pick up the blower and lint-free cloth etc from Jessops (camera shop) this weekend.
Martin Fields overlay plus Question
Nice one on such detailed instructions!
I order a Martin Fields over lay plus today, they seem to have good reviews everywhere i have looked. They are slightly adhesive though, but as this is a "gentle silicon based glue" (so i hear) i think that means it will be fine on the screen.
Has anyone had experience on using these and what the screen is like after you remove them, any residue etc left afterwards? How long will it last roughly?
Thanks for any help guys!
I haven't tried this, but you could probably save yourself the cost of a blower brush by using a bike pump or better still an airbed footpump (you can use that one handed).
tom99, if you get a Martin Fields protector (or any other sort that uses adhesive) I'm not sure that its safe to use masking tape to clean it. The Brando ones stick to the screen electostatically, so its safe to clean them with tape (the instructions that come with it recommend scotch tape). If the instructions you get with your Martin Fields protector don't mention cleaning with tape, then I would miss out that step. Can you add a comment to this thread when you get it (or anyone else that has used a MF protector)? It might help others decide which protector to go for.
I posted a while ago about this with no response. I'd really appreciate some kind of input or advice or anything.
There are those of us who don't like screen protectors on our imates. Of course, after a year, this leads to those little, annoying scratches that seem to magically appear. There's stuff on the market to rub these out; one such product is Displex. I'd like to know if anyone has any experience with these products or any other methods of removing these tiny scratches.
If you haven't had a response in a year, I'd imagine that is because most people like the anti-glare and improved writing surface that a screen protector offers <shrug>
I know those scratches you're talking about but the first thing I do is to get a film for my new device to keep up the resale value.
I know this is a personal preference, but what do you have against films? I can't actually think of a downside to them apart from the first two attempts where you get dust under them and it annoys you for a week before you calm down enough to try it again =)
Maybe you could try one of these polishes and tell us how good they are, after all this information seems to be somewhat lacking ... ?
Amen to that. Actually the good brands (though a bit more expensive) of screen protectors are so easy to apply. I bought a couple of the ultra clear ones from Brando and i'm still on my first for close to a year now. Every now and then I clean the film with rubbing alcohol.
Since I own a few Swatch watches and most of them have already scratched plastic faces, I bought the little tube of scratch remover. It gets the job done but a lot of pressure is required especially if the scratch is very deep. Since my hands got very tired, I then used a Dremel. Word of advise, don't set the Dremel at a high speed because it will melt the plastic.
I don't know if the Magician's screen has some sort of anti-glare coating. When I tried to remove the scratches on my older pair of eye glasses, the anti-glare coating was taken off wether rubbing it manually or using the Dremel.
i've had only bad experiences with screen protectors. I guess that's what i get for being a cheap ass. Plus the jam is my first pda, so i never really realized how much of a problem those scratches really are.
I suppose the solution is to try the Displex screen scratch remover and then slap on a Writeshield AG. Thanks anyway.
I suggest you try first a very small area in a corner of the screen just in case the scratch remover will a a greater damage.
Good luck. Hope you do get your screen as good as new.
zerimar said:
I suggest you try first a very small area in a corner of the screen just in case the scratch remover will a a greater damage.
Good luck. Hope you do get your screen as good as new.
Click to expand...
Click to collapse
Absolutely. I once used scratch remover on my old XDA (Wallaby) and found it to be efective in removing the scratches. Problem - in the area where i removed the scratches the display was compromised - it looked like a prisma of kinds, kinda like when you little drops of liquid on an cathode ray tv - you could see little bits of red green and blue.
I think some kind of layer was removed causing this. So really try it on a corner before you go for the entire screen.
And another word, if you are not familiar with using a Dremel, NEVER use it for cleaning or polishing of plexiglass. I ruined a swatch with that. Used it even at a low speed, but the polishing wheel made the plexi so hot the watchglass actually looked like a bumpy road. Had it professionally repolished at a jewelers place, but by doing this the plexi had got so thin that i broke after a while...
Dremel and plexi - no good in my opinion.
i have a few scratches that came with my magician (i didnt pay a cent for the scratches ). let us know how you go.
BTW, has any one used car polisher for such a task? I heard (not sure how correct/accurate), that its possible to remove small scratchs from cds wih car polisher? I wonder if it works for lcds.
now how is man enough to try it out in there magicians hay :lol: :lol:
Anyone else buy and have problems with it? I searched around after thinking I saw a complaint on it like I've got but couldn't find.
Basicly, I put it on started noticing the top was putting pressure onto the screen I think. THe touch screen got extremely laggy, unresponsivess, and just seemed to go crazy. I'm going to try sanding it down on the inside but I think that just sucks.
On top of that the phone fell out of the back/belt clip half one night and caused a nice freakin dent in my phone and allowed the battery to flip out almost down a sewer.
Anyone care to give me a positive review so I don't just throw this thing out?
Also - is it possible to buy a new physical case to replace a scratched/dented case? Not the body glove I mean the actual phone casing.
chibahawk said:
Anyone else buy and have problems with it? I searched around after thinking I saw a complaint on it like I've got but couldn't find.
Basicly, I put it on started noticing the top was putting pressure onto the screen I think. THe touch screen got extremely laggy, unresponsivess, and just seemed to go crazy. I'm going to try sanding it down on the inside but I think that just sucks.
On top of that the phone fell out of the back/belt clip half one night and caused a nice freakin dent in my phone and allowed the battery to flip out almost down a sewer.
Anyone care to give me a positive review so I don't just throw this thing out?
Also - is it possible to buy a new physical case to replace a scratched/dented case? Not the body glove I mean the actual phone casing.
Click to expand...
Click to collapse
I have this case and had the same problem. I have read that many others have had it too. Honestly I dont know why a company would put out a product like this. They all should be recalled, however me being me decided to just fix it by Taking a dremel tool and shaving some of the inside part of the screen protector off, making it put less pressure on the screen. It fixed it immediately. The case does a great job in protecting the phone, just a major flaw that can be fixed if you have the time and tools. If you dont, ***** to the company and get your money back and try something else.
Praygo said:
I have this case and had the same problem. I have read that many others have had it too. Honestly I dont know why a company would put out a product like this. They all should be recalled, however me being me decided to just fix it by Taking a dremel tool and shaving some of the inside part of the screen protector off, making it put less pressure on the screen. It fixed it immediately. The case does a great job in protecting the phone, just a major flaw that can be fixed if you have the time and tools. If you dont, ***** to the company and get your money back and try something else.
Click to expand...
Click to collapse
Yes I could see that the inside casing was a bit rough so sanding should stop the problem - but seriously that's a major issue.
Have you found that it holds the phone well though? Because I'm very upset that my phone fell out of it once already but maybe it was an error on my part and it wasn't secure enough...
I've never had the phone fall out of the body glove case.
i mangled my body glove case.
someone bumped into me and the phone fell out of the case AGAIN.
i ripped it to shreds and left it on the side of the road to rot into plastic hell.
i dont recommend this product.
I returned mine. I had the exact same issues (screen and phone falling out). It also didn't attach properly on the top left corner, it was always bowed out. I don't recommend it either.
Anyone got any else to share?
I was THIS CLOSE ( || ) to buying it. lol
Is there anything out there that's similar to it in design, but better?
returned
When all the way snapped on, mine pushed the top left corner so hard the entire screen would not respond to touch. Returned it.
My friend and i had the same issue. We just took it off messed around with it and put it back and it works fine, SOMETIMES it happens again but we just take it off and put it on.
Since there is not any other case that provides this type of protection we are keeping it. I rather my phone be safe than anything else.
I just ordered mine yesterday so I'm anxiously awaiting its arrival.
What exactly did you have to mod to get it to work? According to my readings, you just need to sand down the edges that connect with the screen right?
I may just buy the case and sand down what was mentioned. I like the design of the case..only one so far I really like.
I've been using one for about two weeks and am very happy with it. Had read about the screen pressure issue on other posts (searching helps folks), and scraped down the top corners before I put it on. Don't need a dremel tool or sandpaper. No problems, fits perfectly. The only warning is that it's a little dicey to take off once it's on -- it really fits snugly.
Yout're talking about the "sand texture" clip-on case, right? If so, yes, I bought the case too. The top cover was too tight and caused the screen issue people are mentioning. That was an easy fix by shaving down the edges that were pressing too hard (actually, I just cleaned off the coating from the plastic that was causing it... The bottom of the case however wouldn't fit at all. no matter what I tried, I couldn't get all of the clips to lock over the edges of the phone. I removed the felt lining and still had issues. I got around it by using thin double sided tape (for a temporary fix until I got a new case). I wouldn't trust the belt clip with the double stick tape though. I ordered the rubberized case on ebay and the fit is perfect. Just get that one. I sent an e-mail in to Body Glove and have had no response yet. We should all get our money back on these cases, or at least a redesigned bottom case that fits correctly. Right now it was just a complete waste of money. It's a shame, because I really liked the feel of the case.
Torkrench said:
Yout're talking about the "sand texture" clip-on case, right? If so, yes, I bought the case too. The top cover was too tight and caused the screen issue people are mentioning. That was an easy fix by shaving down the edges that were pressing too hard (actually, I just cleaned off the coating from the plastic that was causing it... The bottom of the case however wouldn't fit at all. no matter what I tried, I couldn't get all of the clips to lock over the edges of the phone. I removed the felt lining and still had issues. I got around it by using thin double sided tape (for a temporary fix until I got a new case). I wouldn't trust the belt clip with the double stick tape though. I ordered the rubberized case on ebay and the fit is perfect. Just get that one. I sent an e-mail in to Body Glove and have had no response yet. We should all get our money back on these cases, or at least a redesigned bottom case that fits correctly. Right now it was just a complete waste of money. It's a shame, because I really liked the feel of the case.
Click to expand...
Click to collapse
Could you give us the link for the ebay one please!
http://cgi.ebay.com/NEW-RUBBERIZED-...5|66:2|65:12|39:1|240:1318|301:1|293:1|294:50
That is the one I ordered, and the fit is perfect. The only thing I wish it had was the belt clip insert for the case included. I don't know where to find one, but I mostly keep it in my pocket anyway.
you guys want a good case that protects? check out the monaco aluminum case, it comes with a clear lens on it which I haven't removed but you could if you wanted quick access to the touchscreen. I work in the construction field and have yet to have it fall off my clip. I also dropped my tilt (when I used it) from about 8" off a ladder and it was perfectly fine. The aluminum case for the fuze isn't any more bulky than the body glove case either.
bilbobrian said:
check out the monaco aluminum case
Click to expand...
Click to collapse
I've got one of these as well...and while it does protect the phone very well it will also lower your signal strength. I've had these type cases for the Wizard and Tilt and now the Fuze...whenever I'm in an area where the signal was a little iffy to begin with I WILL either drop the call or be unable to answer with the metal case. So, stay away from the aluminum ones if you go into lower coverage areas (and no...the slots they cut in the back to help improve the signal don't actually help.)
That's pretty much my question. I read the thread talking about doing this with aftermarket ones, and wish I had read it before I applied mine. I got dust under mine. basically want to know if I can wash the one that came with the Fuze and put it back on, before I spend 20 bucks to have a new one shipped to me.
The short answer is "Yes"
Lukewarm water is a good place to start, and don't bother to try to get the "down" side (the sticky side) completely dry: just flap about a bit until most of the water shakes off.
Might find it works better if you have some non-greasy soap around - note that most of the soaps available today will leave their OWN residue behind!
Another handy trick for removing spots of DUST is to simply pick them up with tape. This technique is particularly worthwhile if your only complaint is a small number of dust spots that you can remove (with the tape) by only having to lift one corner of the cover.
Find that a microfiber cloth does a good job with the Exterior service of the screen cover, with a bit of "Safe For Coated Lens" cleaner sprayed on the cloth if the cover is particularly grimy....
Why would you when they only cost a few pence!!!!
I just use regular seetrough tape, apply it all around, rub it on tight, then pull it of. after that apply it imidiatly to the phone, otherwise it'll collect dust again.
water didn't work on mine.
@jim: you would because this is FREE, no trouble and no waiting for your products (some people can only order them online from other countries and have to wait a week (or 2) ). + I think the factory one is the best (I have a differrent one but I liked the factory the best)
Thanx for the help. I heard the factory one was the best as well, that is why I wanted to stick with that one. That being said, I was using my phone in the car the other day,(not whilst driving) and forgot I left it on my lap, and well got out. long story short I guess I'll have to order a new one anyway. the phone made it alright, just 2 small chips. lucky i had the screen protector on though. Any one know of any as good as factory?
I just put a Martin Fields protector on my Fuze and love it. It's definitely on par if not better than the factory one.
Have an Exim screen protector on its way, but don't expect to receive it until early (hopefully) next week.
Have also been pleasantly surprised by the included screen cover - but wish they had included a protector for the keypad area as well. At the moment, intent is to mount the Exim's keypad cover once it arrives and save the screen cover until ready to replace the OEM one.
Pricing on screen covers varies widely: have had good luck with Boxwave covers for my Axim, but am ready to try some of the less expensive options with the Fuze.
Mattijn106 said:
I just use regular seetrough tape, apply it all around, rub it on tight, then pull it of. after that apply it imidiatly to the phone, otherwise it'll collect dust again.
Click to expand...
Click to collapse
you can use the steam trick, go into a small bathroom and run the hot water until there is a lot of steam. This will drop the dust particles from the air, ensuring you don't get any dust on the screen or protector while applying.
bboyneko said:
you can use the steam trick, go into a small bathroom and run the hot water until there is a lot of steam. This will drop the dust particles from the air, ensuring you don't get any dust on the screen or protector while applying.
Click to expand...
Click to collapse
I hope you mean just the screen protector...
taking your phone in a steamy room is just stuipid
gbueh said:
I hope you mean just the screen protector...
taking your phone in a steamy room is just stuipid
Click to expand...
Click to collapse
im sure nothing will happen to your phone in a steamy room
unless condensation occurs inside the phone, you're fine
i have so many phones
i always bring them into the bathroom,
i just leave it on the counter
i have never had a broken phone due to steam
not a porn site ;-)
These are reasonable priced and offer excellent protection.
http://www.bestskinsever.com/servlet/StoreFront
it's awesome way to remove dust by tape so i tested it and success with me
Hello everyone.
I got my HD2 a couple of weeks ago and as usual with new toys, am still taking some extra care with it. I had a Touch HD before that withstood quite a few bumps and two small drops. I saw people carying iPhones in pants pockets, back and front. Given that HD2 screen is significantly larger, how fragile is it, really? I usually carry my phones in jacket pocket, screen towards the body, without any case or sleeve. Do I need to take so much care for it or is it actually more resilient than it seems? Yes, I've seen the threads with broken screens. Anything can break, given enough force.
Any serious feedback is welcomed. Thanks.
Cheers, R
Well I have had mine since it was released in the UK and have had it in my right hand side front pocket in my jeans/trousers etc, sat on floors etc and all sorts and nothing has ever happened to it at all. Its a pretty tough screen I think, as long as when its in you pocket its not at an odd angle, I cant see any problems keeping it in there. I certainly have no problems.
Scratch test
There is a YouTube video of a scratch test of the screen of an HD2, its in foreign but gives a good idea of its screen tolerances (those of a nervous disposition may wish to look away towards the end)
http://www.youtube.com/watch?v=NcEaehKWr2s
Hmm I can only speak for myself and my HD2... but my screen has 2 (really small) scratches..
I think these are from a keychain or maybe a lighter in my pocket. I don't really know where the came from - but not from dropping it.
I would recommend to use a (thin - not that thick vikuti) foil to protect it against scratches.
--> Question: What would you recomment regarding a foil to cover the screen? I bought 1 Vikuti foil and really disliked it - it is sooo thick
Edit: I think the knife in the video would be able to scratch the screen... only a matter of right angle an pressure
I dropped mine on new years eve - drunk and the only thing i noticed the following day was that i had lost the backplate lol
Someone on here very kindly gave me a replacement.
Other than that - no scratches so far
Had mine three weeks, using front trouser pocket though I am very conscious of checking the pocket for keys etc first.
I have a full body invisibleSHIELD skin, and i'm extremely happy with it.
I've knocked it a few times on the edge of tables and chairs, once on the metal hand grip on a bus seat, and theres not a mark on it anywhere.
I have a screen protector that covers the entire screen, and carry the phone in my pants pocket in the leather case that came with the phone (I'm waiting on a holster from eBay).
The screen is in perfect condition, however, I did scuff the corner of the HD2 by dropping it (in its leather case) as I went to put it in my pocket coming out of a movie theatre...dropped onto cement.
: /
I use a screen protector and have a very nice silicone case for it that fits very snug, but I'm just being careful.
I believe that common sense is enough to keep this device from being damaged. As you can see from the linked video above, the screen is very resiliant, but it's not scratchproof. Also, why on earth anyone would put it in the back pocket of their trousers and sit down is totally beyone me, but people have done it (and probably still do), but they end up on here asking how to fix their damaged screen. (My advice to them is to hook up a flex capacitor to their car, drive at 88mph, go back in time to before they broke it and slap themselves round the face and say "STOP BEING SILLY!!!")
It's tough, but not unbreakable. Just treat it with respect, look after it sensibly, and DO NOT PUT IT IN YOUR BACK TROUSER POCKET OR FRONT SHIRT POCKET!!!
As the meerkats say... simples
(I hate those adverts, but I do like Back To The Future )
johncmolyneux said:
FRONT SHIRT POCKET!!!
Click to expand...
Click to collapse
Why not...I put it in there all the time?
So it won't fall out or...?
Spike15 said:
Why not...I put it in there all the time?
So it won't fall out or...?
Click to expand...
Click to collapse
lol - I've NEVER seen anyone on this forum say that that has happened to them <sarc mark>
johncmolyneux said:
lol - I've NEVER seen anyone on this forum say that that has happened to them <sarc mark>
Click to expand...
Click to collapse
Just making sure I wasn't missing something.
Personally I don't bend over when I need to get something on the floor et cetera...I bend my knees...I've heard that bending like that is bad for your back.
Spike15 said:
Just making sure I wasn't missing something.
Personally I don't bend over when I need to get something on the floor et cetera...I bend my knees...I've heard that bending like that is bad for your back.
Click to expand...
Click to collapse
Yes, and even moreso if you have a hernia! Good to see that xda is also responsible for good health advice too
I can't wait for mine to arrive next week. I can tell you from experience that the IPHONE has cracked 3 times in pocket when I put too much pressure. Apple does replace them on a regular basis. They allow for what they call a hairline. If it spiders they won't replace it but a hairline is within their tolerance and is common enough for them to replace it without question. That is how I ended up with a new replacement recently. I wasn't using the phone much but my HD battery died on site so I put the time into the IPHONE to use it. I squatted with the IPHONE in backpocket and CRACK. I probably should check my beltline while I am at it..
They replaced it and that worked out anyways as I am going to sell it. Keep my HD and Bold as backup.
The glass looks pretty solid and as many people reported it a good solid piece of hardware.
i keep mine in the case it comes with when i am carrying it around... any pocket really.
i just make sure i dont sit on it! lol
the screen itself is extremely resilient when it is out and in use.
I leave mine lying around all of the time out of the case and it still looks brand new.
I dont use any screen protector.
screen strength
being a kapasitive screen it uses a propper glass cover instead of ****ty plexi glass or resistive glass as most phones use, this naturally gives it a more scratch proof serface but makes it less resilient to actually breaking. like one guy said it all has to do with angle and preshure.. and abit of bad luck when it comes to screen protection i recomend invisiShield. they are nice and thin, VERY clear plastic so it doesnt disturb teh screen quality. and last but not least, the fabric its made of is teh same as teh stuff that they use to cover helicopter rotor blades with, so it comes with a 30 year waranty.
Thanks for all the replies so far. I suspected as much, but it sure is nice to hear other people's experience
Cheers, R
Impunitus said:
Thanks for all the replies so far. I suspected as much, but it sure is nice to hear other people's experience
Cheers, R
Click to expand...
Click to collapse
I had the same fear with its screen .. i posted a poll on the screen
see this
http://forum.xda-developers.com/showthread.php?t=618978