I have searched and searched and searched, only finding unhelpful suggestions from people not too qualified to offer said unhelpful suggestions, haha. This bastard Moto X will not charge, regardless of charger/cable used (OEM Turbo and regular), no USB trickle charge, and I caved and got a new battery despite knowing better and it still won't charge. It stays on while plugged in and runs until the percentage reaches 0% (rate of discharge isn't always consistent). I've tried a whole host of dumb tricks like draining battery to 0%, selecting "Power Off" from fastboot, and holding Power/Volume Down for five minutes. Doing the latter seems to be the only thing that allows it to get a charge, but it's kind of wholly impractical to do that every day for who knows how long to make a difference. Also did complete factory reset and fresh reinstall of both factory and cm13 ROM and clearing ALL the caches, still to no avail.
So because it will slightly charge in the constant fastboot/reset process of holding Power/Volume Down, I've come to the conclusion that it's a kernel thing because of a damaged component on the board. Biggest issue is that the battery is reported as "Cold", with a general temperate reported by multiple utilities at -32 degrees. I can't upload screenshots at the moment, but TWRP reports system temp as a massive string that covers 2/3 of the bar up top. So for whatever reason the phone isn't getting a reading from the battery temperature sensor, and it's refusing to allow the battery to charge. I've been searching like crazy to find a way around this, be it editing the kernel to ignore temperature, or finding a schematic to know where to look for related circuitry responsible for this. I DID find a single component that has been broken from the previous owner tearing into it to replace the screen, but it's up near the button connector and just seems like an inefficient place to take anything relating to the Power IC. Regardless, since I can't find any way of identifying exactly what it is and what it does, I'm not sure how to handle this. Any flippin' suggestions?
tl;dr - I had pizza leftovers for breakfast and I regret it.
illitero said:
I have searched and searched and searched, only finding unhelpful suggestions from people not too qualified to offer said unhelpful suggestions, haha. This bastard Moto X will not charge, regardless of charger/cable used (OEM Turbo and regular), no USB trickle charge, and I caved and got a new battery despite knowing better and it still won't charge. It stays on while plugged in and runs until the percentage reaches 0% (rate of discharge isn't always consistent). I've tried a whole host of dumb tricks like draining battery to 0%, selecting "Power Off" from fastboot, and holding Power/Volume Down for five minutes. Doing the latter seems to be the only thing that allows it to get a charge, but it's kind of wholly impractical to do that every day for who knows how long to make a difference. Also did complete factory reset and fresh reinstall of both factory and cm13 ROM and clearing ALL the caches, still to no avail.
So because it will slightly charge in the constant fastboot/reset process of holding Power/Volume Down, I've come to the conclusion that it's a kernel thing because of a damaged component on the board. Biggest issue is that the battery is reported as "Cold", with a general temperate reported by multiple utilities at -32 degrees. I can't upload screenshots at the moment, but TWRP reports system temp as a massive string that covers 2/3 of the bar up top. So for whatever reason the phone isn't getting a reading from the battery temperature sensor, and it's refusing to allow the battery to charge. I've been searching like crazy to find a way around this, be it editing the kernel to ignore temperature, or finding a schematic to know where to look for related circuitry responsible for this. I DID find a single component that has been broken from the previous owner tearing into it to replace the screen, but it's up near the button connector and just seems like an inefficient place to take anything relating to the Power IC. Regardless, since I can't find any way of identifying exactly what it is and what it does, I'm not sure how to handle this. Any flippin' suggestions?
tl;dr - I had pizza leftovers for breakfast and I regret it.
Click to expand...
Click to collapse
DID YOU FIND A SOLUTION? I'm facing the same issues with my moto x pure edition (XT1575) after a screen replacement. Ampere aplication says the battery health is "Cold".
I never did, unfortunately. I tried a different battery in the event that some onboard IC was damaged, but it performed the same way. Whatever component was damaged seemed to be responsible for relaying pertinent information regarding battery temp readings; and without it the phone was getting that -32 reading which was beyond a safe/efficient range to allow charging (presumably). In my research, I think I remember it being possible that fiddling with the kernel itself to bypass battery temperature requirements is possible, but that's beyond my level of knowledge and runs the risk of being potentially unsafe since all it takes is one instance of getting too hot for the whole thing to go up in smoke. As frustrating as it is, it's not worth the potential damage to the device and/or home.
Not to say that your issue is the same as mine concerning cause, but the end result of how to bypass it would more than likely be the same :/
Same issue... Well... On my way to it.
I mean, my XT1575 will only charge if I lift the micro usb cable in a very very specific way. And everyday that passes, it's getting more a more difficult to find the right spot
DiegoMarinDiego said:
Same issue... Well... On my way to it.
I mean, my XT1575 will only charge if I lift the micro usb cable in a very very specific way. And everyday that passes, it's getting more a more difficult to find the right spot
Click to expand...
Click to collapse
I had that exact issue with the included 25W quick charger after a while. Switched to another charger and cable and the problem was solved for me.
Related
My Micromax phone(Yureka Plus) has been having a few charging problems lately. First let me list the problems that i have seen, and diagnose it as much as i can on my end.
The battery shows the charging indicator but the percentage doesn't always increase.
When I pull the battery the percentage changes at times-increases or decreases,but this doesn't always happen.
The phone sometimes refuses to charge entirely, and it takes multiple tries to get it to do so.
Also very rarely the after switching off the phone and charging it, the screen suddenly starts flickering blue-and only can be fixed by pulling the battery(Happened twice so far)
It shows particular resistance to increase in charge,especially beyond the 70% range-its practically impossible to get it to 100%
When I connect it to a laptop,it does get recognized and i am able to access the files on it(However there seemed to be problems when using an OTG, cant confirm ATM)
When using the phone while charging it either discharges or remains at the same percentage,usually the former.
Its not a software issue as i havent updated the phone in the past month, and the problems began about 2 weeks ago
I have changed cables,power sources and tried to recalibrate the battery-none of them worked.
The problem may or may not be connected with the following-The day before the issue started i was cleaning the phone using water.
I did find some amount of water in the case, but it hardly was enough and none of it seemed to be there near any electrical components
I cleaned the usb port,battery connectors, pins,and did a visual inspection, nothing seemed out of place.
The water damage indicator of the phone seems to be normal.
However the battery does spin-only on one end though...it doesn't spin on the other end.
Thus i am not sure if its a sign of battery damage or just how its manufactured...I think that swelling should be universal and not discriminate between sides.
Unfortunately i will not be able to give the phone for repair/buy stuff as i am out of town for about a week
Is it just a bad battery or something more serious? Like a problem in the logic board or something?
2018 may be late in the game to become a new owner of a OnePlus 2 phone. But here I am. My main phone at present remains a Samsung Note 4, and I'm trying to get a feel for how this old (but not as old as the Note 4) phone can be repaired. My issues are a mix of battery, possible circuit board, and other problems / eccentricities.
The phone was given to me non-working. I have a minor-league reputation for rescuing phones, so thought I'd try this one.
First, I had to get it up and going. Nothing worked initially. I wasn't delighted to find out the battery is only accessible after removing two covers and about 30 microscopic screws. I reset it by pulling the small "plug" at top center-right and the phone decided to allow me to boot. I immediately (per instructions I found elsewhere here) went to fastboot and wiped the cache.
I did manage to install TWRP and the latest (as of a few days back) version of Lineage 8.1. But then the problems began again. The phone would suddenly, after charging for a while (and reporting a battery that was nearly charged), shut down. No charging icon showed on the screen.
Fast foward. Today, I got a cheap knock-off battery in the mail. It intially worked and I got it nearly charged. But after more spontaneous reboots I noticed something odd; in TWRP, the battery said only 50% charged while in Lineage it said 97% charged. So once again I wiped the cache and this time the ART/Dalvik cache as well (pointless, but ya never know).
This did get the two percentage reports matching up. And initially it got the phone working again. But alas, once again, the phone started the shutting down.
Currently, I'm leaving it overnight to charge - if in fact it is charging (how does one tell)? If that doesn't work, I'm thinking about using Odin to totally reflash the original version of the operating system.
Any other ideas or input - including laughing at me for bothering with this - is permitted.
I will say that the engineering of this phone compared to the older Note 4 leaves the Note easily the winner; to take its battery out is a matter of 20 seconds. Really not impressed with my OnePlus experience so far...
Thought I'd update things. After spending a day on sites (here and on the official OnePlus community boards) I tried any number of fixes. I'm reasonably convinced the only way to somewhat consistently start my particular OnePlus 2 phone is to:
1. Open it up, thus voiding the warranty (hehehe.... by now that's void anyway).
2. Unplug the battery's small plug at upper right-center of battery (a fingernail works fine, but do make sure the phone isn't plugged in!)
3. *Leave the back off* or at best gingerly snap it on but without attaching the screws. (Every time I did so, even after extensively using the phone while it lay on my sofa's arm and rebooting it numerous successful times previous to replacing the screws, the phone refused to reboot.)
4. I also cleaned the usb c socket with a wood toothpick and was a little surprised at how dirty it was; I did the same in a minimal way to the battery contacts.
5. I found no real use to having the actual OnePlus charger; I used it a bit but my best results came from the Samsung charger and a new (though cheap) usb c cable I nabbed via ebay.
Today I did get the phone going and intentionally wiped Lineage and installed the latest (2017) version of the OnePlus2 official os. It went on fine. I rooted it, installed apps, and (as mentioned) repeatedly shut down and restarted the phone, which promptly restarted with only a 3 second lag. I did this 5 times because one thread I found suggested this was an official OnePlus suggestion. (I rolled my eyes but did it anyway.) Played with the phone a bit, then shut it down again and screwed the back on. As noted, the phone suddenly wouldn't turn on again.
In summary, I'm not sure if this phone can be meaningfully resurrected. If I knew where what may be a short in it was, I could possibly replace that part. But I have little idea and am not quite the geek enough to sort that out. I am guessing at a short because without the lid or screws, it wants to work. It wants to be a good phone for me and I'll keep toying with it for a while longer.
Any suggestions appreciated.
Third post is a question for others:
Has anyone else experienced their OnePlus 2 working fine *without* the back cover screwed on, but as soon as it was screwed on the phone stopped working and wouldn't start again? And, if so, did they ever sort out why?
I'm going to make this a separate discussion.
Hey. I experienced the same symptoms with a "official" replacement battery I found online. Random reboots over and over again until I couldn't even turn it one anymore.
TWRP was always showing different battery percentages than OS.once I put back in my old but original battery that came with the phone it turned on again and it works flawlessly again.
maikl91 said:
Hey. I experienced the same symptoms with a "official" replacement battery I found online. Random reboots over and over again until I couldn't even turn it one anymore.
TWRP was always showing different battery percentages than OS.once I put back in my old but original battery that came with the phone it turned on again and it works flawlessly again.
Click to expand...
Click to collapse
This is something I've read, and may well do. It also, however, raises another thorny set of issues re battery calibration. I understand that sometimes new batteries have to be "calibrated" by being charged, discharged completely, charged again, discharged completely, and charged yet again and discharged. After that, things are supposedly going to run right. Trouble is in my case, the phone doesn't want the battery; it keeps stopping completely and not restarting. Either the battery stats are wholly inaccurate (says around 57% charged during those brief times I've had it up) or I need to go with your idea. Trouble is there the original battery from this phone is dated 2015; I hope it has anything at all left to give.
shonkin said:
This is something I've read, and may well do. It also, however, raises another thorny set of issues re battery calibration. I understand that sometimes new batteries have to be "calibrated" by being charged, discharged completely, charged again, discharged completely, and charged yet again and discharged. After that, things are supposedly going to run right. Trouble is in my case, the phone doesn't want the battery; it keeps stopping completely and not restarting. Either the battery stats are wholly inaccurate (says around 57% charged during those brief times I've had it up) or I need to go with your idea. Trouble is there the original battery from this phone is dated 2015; I hope it has anything at all left to give.
Click to expand...
Click to collapse
Mine is dated 2015 as well and I'm getting through the day with closely 3 hours of SOT.
maikl91 said:
Mine is dated 2015 as well and I'm getting through the day with closely 3 hours of SOT.
Click to expand...
Click to collapse
I'm trying this in desperation. The phone has gone completely unresponsive at this point, and I'm looking at having a technological paper weight. Hope I can resurrect it but the odds are not good.
Some progress, some regress.
Here's what I'm seeing. I can get the phone up and running again after extensive recharging. As long as I leave the back of the phone off - that is, both the inner and outer backs - it seems willing to keep running. As soon as I snap the inner back into place, not even with the screws yet, the phone locks up. Soon after, around 10 to 20 seconds, it shuts off. Sometimes it will restart and other times it won't for a long time, even after unplugging and replugging battery.
Has anyone else run into shorting or grounding issues associated with the back (inner, the one w/ 18 screws) case?
I am now back to a dead phone. A new (3rd party) battery is my current hope... charging it for over a day now has not yet led to the phone showing any sign of life.
One other question: I know both this cable and charger work, but as they are not the "original" OnePlus charger / cable combo, could that be the difference? I'd appreciate it if there is any clear evidence regarding this question.
The below article raises a disturbing possibility, based on the reality that OnePlus cables and chargers are - by OnePlus' own admission - non-standard and possibly could harm other electronics. But on top of that, and not well explored in the article, is whether or not OnePlus' charger/cable combo might even be damaging to the OnePlus 2 (and other OnePlus phones). They "assure us" this is not the case. Hmm.
https://www.androidauthority.com/oneplus-responds-to-bad-usb-type-c-cables-658048/
I thought I'd update this thread with what may be the final installment.
I invested $70 in a highly bent but somehow still working second OnePlus 2 phone off ebay. (The guy had a great fall on a log story as to how the phone got bent.) Long story short... I gambled and won. That is, I gambled that the innards of the second phone would go into my first phone and that the first phone's screen would work. YES. And so, after playing amateur phone repairman, I have myself a OnePlus 2.
So many questions. Going to peruse this board now...
Hello everyone my brother's Ph-1 keeps shutting down right after powering up, I have tried everything from factory resetting to trying a different charger, nothing seems to work. This happened after he didn't use the phone for almost a month, it worked perfectly before.
It powers off even when on charge or connected to the laptop.
The phone doesn't stay on for more than a minute or two which means i cannot use ADB to side load an update
The phone is running Android P and the April security update patch.
Please do help me out
Thanking you
Kalasingha said:
Hello everyone
Click to expand...
Click to collapse
Hello everyone
Kalasingha said:
Hello everyone my brother's Ph-1 keeps shutting down right after powering up, I have tried everything from factory resetting to trying a different charger, nothing seems to work. This happened after he didn't use the phone for almost a month, it worked perfectly before.
It powers off even when on charge or connected to the laptop.
The phone doesn't stay on for more than a minute or two which means i cannot use ADB to side load an update
The phone is running Android P and the April security update patch.
Please do help me out
Thanking you
Click to expand...
Click to collapse
It could be corrupted though it sounds a bit like a battery issue, to me. If battery discharges too much eg it didn't shut down itself properly when battery was at a low level (they retain more charge than shown to user so it can shut down with proper procedure) & the battery ran down past it's reserve the battery may not be able to be recharged with a normal charger even though you charge it. (Thought a battery specialist could possibly revive it with a boost charge, though I've only seen these used with industrial batteries)
with a "dead battery bootloop" sometimes you can get it going by booting when connected to the charger, but you'll probably need a new battery. Maybe also try boot into safe or recovery mode when connected to Essential charger. (I'm assuming your phone not corrupted, though as you haven't given us much info about exactly what happens & what you are seeing)
IronRoo said:
It could be corrupted though it sounds a bit like a battery issue, to me. If battery discharges too much eg it didn't shut down itself properly when battery was at a low level (they retain more charge than shown to user so it can shut down with proper procedure) & the battery ran down past it's reserve the battery may not be able to be recharged with a normal charger even though you charge it. (Thought a battery specialist could possibly revive it with a boost charge, though I've only seen these used with industrial batteries)
with a "dead battery bootloop" sometimes you can get it going by booting when connected to the charger, but you'll probably need a new battery. Maybe also try boot into safe or recovery mode when connected to Essential charger. (I'm assuming your phone not corrupted, though as you haven't given us much info about exactly what happens & what you are seeing)
Click to expand...
Click to collapse
The phone shuts down even when in recovery or safe mode whilst connected to the charger.
It does sometimes fully boot up and then shutdowns, but mostly shuts down while still on the essential logo.
If I may ask what do you mean by the phone might be corrupt?
Can one month of non usage cause the battery to die out?
Kalasingha said:
The phone shuts down even when in recovery or safe mode whilst connected to the charger.
It does sometimes fully boot up and then shutdowns, but mostly shuts down while still on the essential logo.
If I may ask what do you mean by the phone might be corrupt?
Can one month of non usage cause the battery to die out?
Click to expand...
Click to collapse
by corrupt I mean some data that is part of the boot process causes bootloop so it shuts down, but as your phone is shutting down at different points in boot cycle I think it's probably battery
Leaving the phone turned off unused for longish periods should not be a problem normally even with a few % left in battery. And even if left turned on it should shut itself down when battery low & be able to boot up again after a month due to the battery "reserve" capacity (but possibly a month was too long). And if it was not recharged straight away and/or rebooted multiple times the battery "reserve" could fall too low and not have enough power to start/shutdown properly (possibly causing data corruption ... though l don't know if there is some sort of fail-safe boot procedure ) Then there is a possibility there is a hardware fault with battery/phone that meant battery lost too much power.
There were some tricks ie "boost charge" you could do with removable batteries that were in "deep sleep" as shown here for example
https://m.youtube.com/watch?v=TEXA7qIJ968
But they don't really work without taking your battery out (for us we might as well get a new battery when opening phone up, & there would be some risk that you damage battery as we do not know the exact charge to apply on this battery, which could cause unsafe battery) I wouldn't want to freeze my phone even though it should survive OK, as I'd be alittle concerned about long term effect on our screens small pixels (I remember the guys at popular mechanics put an old flip phone with little LCD screen in liquid nitrogen & it still worked after being warmed up!).
See https://batteryuniversity.com/learn/article/low_voltage_cut_off
for more tech details
firmware issues do not cause the issue you are describing
you have a hardware problem
sounds like a bad battery to me
good news is the battery is not difficult to replace (don't listen to ifixit I am not sure what they where smoking when they did there tear down)
https://www.youtube.com/watch?v=BCKxAQXdTJ8
don't bother with silly and wrong tricks like trying to hack the battery back to life its the wrong way todo
if the battery ever gets to that point then the battery is bad enough said
Legitsu said:
don't listen to ifixit I am not sure what they where smoking when they did there tear down
Click to expand...
Click to collapse
So true! )) As much as I respect the guys from iFixit, they screwed this one up pretty badly - basically, made a tutorial on how to destroy your phone. Fixez.com did much better.
Please can someone help me with a problem I’m having with my Samsung Galaxy s5.
I put my phone on charge before I went to bed and when I woke up it was still showing a red LED. I knew this was wrong because it should have had enough time to charge and turn green. I had not powered the phone off before putting it on charge and I plugged it into the same USB 3.0 charging lead I have been using for the past six months. I unplugged the phone and pressed the power button to light up the lock screen but it didn’t light up.
I’m thinking possibly something has either shorted or over heated and fried something either on the charging port assembly or one of the chips adjacent to the port while the charger was plugged in. It seems like only a trickle of power is getting through to the phone. When I plug a different USB 2 charging cable into the phone, without trying to power on, the charging icon appears but shows no charge at all in the battery.
I have also tried the spare battery I have but it’s still the same. I know the spare battery is 100% fully charged because I store it in a separate charging/storage box which shows a green LED when it is full. In fact the one which was in the phone at the time is also fully charged according to the charging box. Neither battery has got warm at all inside the phone. I’m confident both batteries are fully charged and totally fine and the problem isn’t with the batteries.
At this point I removed my sim card and also the MicroSD card. I needed the sim to use in my spare phone and I wanted to see if the sd card could be causing the issue but after again trying a normal reboot it made no difference.
I’ve tried several possible things I found on google but nothing has worked. Between each different thing I tried I had to remove the battery for 10 seconds and insert it again to get it out of the boot loop so I could try something else.
Initially when I tried booting into safe mode, then recovery mode and then download mode it brought up the screens for those but in each case after a few seconds the phone powered off and went into a boot loop so I couldn’t attempt any recovery options such as clearing cache etc. Now I cannot even get it to start any of those modes at all and all that happens is the phone does a little vibration, displays the Samsung logo and then just boot loops no matter what I try.
I have tried removing the battery and leaving the phone for a few hours then powering on again but it still just loops.
I have tried pressing and holding Vol-down when plugging it into my PC using a different USB 2 cable and windows acknowledged a phone was plugged in but said it couldn’t connect or recognise the phone and suggested the phone could have a fault.
I don't know if maybe my USB 3.0 lead has a fault that could have caused it or if there could have been some electricity spike while the phone was plugged in, or as I said a component has just fried.
I strongly suspect this is a hardware fault and not a software fault but as I’m not a phone engineer I have no idea about how to trace any possible hardware issues or what might have gone wrong. I would really appreciate any help or suggestions about what the problem might be as this has been a great phone for the last 2 years since I got it and I’d be sad to have to junk it and buy a new one.
Thank you.
I would not junk it yet......
You had mentioned that you go through a lot, just to get phone into Recovery ( " Initially when I tried booting into safe mode, then recovery mode and then download mode it brought up the screens for those but in each case after a few seconds the phone powered off and went into a boot loop so I couldn’t attempt any recovery options such as clearing cache etc. Now I cannot even get it to start any of those modes at all and all that happens is the phone does a little vibration, displays the Samsung logo and then just boot loops no matter what I try." )
OK, just my 2 cents here on this... Why not trying to goto Recovery by pressing and holding the Volume Down (vol-); Home button, and The Power button all at the same time. (yes, if you have a Recovery, and its works, you should be able to boot right into Recovery- >Now, (I would, cause I've been there..) I would also have a PC going with Odin open (Plus the Latest Stock Rom) ... If it works, you would flash the Stock ROM, to clean up anything, giving you all stock, but you can change that of course ...then go from there...
Second, if you can not still get to Recovery.... Have you tried a Stock USB Cable, only asking.... Obliviously something is a miss... with Power... IF phone is off, and you plug it to a power source ... then system has power, and these can power up with just the usb cable, without having the battery in..... Been there. Can add the simple fact, if using just a Micro SD cable, they can bend the Power Board. Believe me (Had to fix the Wife's S5 a few Frinkin' times....) That is why, I say using the Stock Cable, or even a USB 3.0 Cable (like the stock one) does help with power issues when the Micro has bent up the power board...
Will check back and see if this may have you to Recovery or fixed... sure hope this can help you out
Thanks for replying godofsalt.
At the time the phone was plugged in to my USB 3 lead which charges faster and all I can think is that perhaps there could be a fault with the lead or the higher ampage of using this lead caused a circuit to burn out.
I have around a dozen USB 2 leads and I've tried your idea with 3 different ones but none of them will fire up the phone at all with the battery taken out.
I am sure this is going to need some kind of replacement either of the charging port or the motherboard. I don't rate my chances of trying to do it myself and I don't think it will be economic to take it to a shop so I've found a better option by buying the same phone which is second hand but in good condition. That way I know I have all the additional accessories already for probably the same price any shop would charge to fix it.
In future I'll stick to using a decent USB 2 lead on the 1 amp charger I used to use before and hopefully this will not occur again.
G500F battery graphic/boot loop
Had the same problem a few days after installing a 9.0 Rom. My battery is brand new and all cables aren't too aged, so I thought this had to be a physical fault of some kind, but then I had the thought to flash an older bootloader and just like that my battery started taking a charge again and I could boot up. Switched to Flyme os for a while the went back to 9.0 again, with the lastest bootloader and the thing stopped working again. Don't know too much, but I'd try and flash a different bootloader to see if there's any difference. My device failed right at the Galaxy logo, then looped the charging graphic endlessly but would strangely go into download mode and not fail. Don't know if this helps, just thought I'd share my solution.
Thanks for replying henderia93.
My symptoms are very slightly different in that the phone couldn't maintain any of the modes I tried for more than a few seconds before going back to the boot loop again so there was no chance of trying any software fixes including flashing the ROM. Now it won't enter any of those modes at all. I'm certain that's due to only a trickle of power getting through to the main board, not enough to maintain any recovery modes, so there is just enough power for it to attempt to boot, but no more so it just keeps looping, most likely caused by something that has blown while on charge.
MarylinC said:
Thanks for replying henderia93.
My symptoms are very slightly different in that the phone couldn't maintain any of the modes I tried for more than a few seconds before going back to the boot loop again so there was no chance of trying any software fixes including flashing the ROM. Now it won't enter any of those modes at all. I'm certain that's due to only a trickle of power getting through to the main board, not enough to maintain any recovery modes, so there is just enough power for it to attempt to boot, but no more so it just keeps looping, most likely caused by something that has blown while on charge.
Click to expand...
Click to collapse
I ha e taken so many of these a part... Like I may have mentioned, there is a Board, just for the USB (data and power (i still have 2 of them)).... In short, you really have to pretty much take the phone a part. Being very careful with the Screen, and the "Sticky" LEDs and the Home button. There is a lot to it actually.
Like I said, been there done that... Cheap to get, takes some time but it is possible to replace that board. It's a separate board different from the actual main CPU board.
I would have to find it, but I had a manual, for taking these a part.
godofsalt said:
I ha e taken so many of these a part... Like I may have mentioned, there is a Board, just for the USB (data and power (i still have 2 of them)).... In short, you really have to pretty much take the phone a part. Being very careful with the Screen, and the "Sticky" LEDs and the Home button. There is a lot to it actually.
Like I said, been there done that... Cheap to get, takes some time but it is possible to replace that board. It's a separate board different from the actual main CPU board.
I would have to find it, but I had a manual, for taking these a part.
Click to expand...
Click to collapse
While I've been looking for answers about this I've seen teardown videos for the s5 so I can see what the port assembly looks like with it's little PCB behind it. As I have a replacement s5 on it's way all I need to decide now is whether to keep the old handset for spare parts or see if I can follow the teardown video to try and install a new port assembly to get the phone working again as a spare.
MarylinC said:
While I've been looking for answers about this I've seen teardown videos for the s5 so I can see what the port assembly looks like with it's little PCB behind it. As I have a replacement s5 on it's way all I need to decide now is whether to keep the old handset for spare parts or see if I can follow the teardown video to try and install a new port assembly to get the phone working again as a spare.
Click to expand...
Click to collapse
Yep, me too, seen many vids on the tear down. I decided to go a bit more, IMHO, to have an actual manual, PDF, when I did my first one, many years ago. So, can read, and use photos wisely. Seen too many Utube crap, where the break it, destroy it..... crazy!
Well, at this age, not too sure what to do my self. In our case, our present service is cheaper to Keep these. Grandfathered in, and we pay a but less, than going to any other carrier. Plus, these newer phones are not cheap at all.
True, it up to you. hope all goes well.
Sorry I am a novice so please excuse my question.
Are you assuming that the usb port is shorting even when no usb cable is inserted? As you put a fully charged battery in with no change it would seem that the act of charging is not involved.
Have you tried a voltmeter to check the voltage at the battery charging pins?
Have you tried to check the voltage at the two pins commonly used for a wireless charging adapter (to the upper left of the battery) to see what the voltage is?
Sorry if I am off base.
Have a Sm-T530NU that has misbehaved for a long while, originally the OEM battery was thought bad. Yet after it was changed to a new off-brand battery and working on and off for a year and some, the tablet has started misbehaving again, mostly not charging and turning off alone. And recently has started showing the temperature warning icon while charging while off.
So, I've opened it again and digged down, and discovered the battery connector on the PCB wasn't well soldered, the contacts danced in the pad, so I retouched the soldering with flux and a little new solder and it seems ok (I can recheck again later if needed be), so I tested the original battery with multimeter and seemed acceptable, so I installed the original battery back. Charged it for a while, and, again, warning icon for temperature while off, and it switches back and forth between charging and warning... I turned it on, and it works, but throws an error once in a while about being too hot and closes all apps... this, I think should be something related to cpu heat and not battery one... (also wasnt charging during this). So, I read online that some of these tablets with a modem have a service menu (*#0*#) but of course this one has no dialer, so I've tried several programs to try and get into the service menu, my idea is to see if it's possible to recalibrate temperature sensors, for battery and for cpu, but I've not been able to open the service menu by any means (the last mean I have is trying an intent initiated by am but the tablet is not rooted and there's permission issue for asking an intent of uid 2 from uid 0....).
My questions are:
1) Is it possible to get to the service menu of this model somehow? with or without rooting? Is it possible to recalibrate sensors from it?
2) Should I recheck the battery connector? would a battery "overheat" (caused by a bad connector connection to the sensor cable, or a miscalibration) cause app shutdown during run? or is it related to cpu/gpu overheat? I see some phoen models (S2) can cause this message from torubles with the usb connector/pcb, this doesn't sound too logical on my case, but, is it a possible source of problems for this tablet too?
3) If it IS a cpu overheat (though tablet feels cool to the touch) is there anything can be done to help with this issue? micro disipator maybe?
Thanks for any advice. I'm willing to try odd or hard stuff to fix this.