Related
Hey guys I'm not sure if this is the right place to ask for help. I'm trying to boot into recovery and it's not working. I'm using a Lg G2 (Sprint). I was running Unofficial CM 10.2 and had a twrp recovery (2.6.3.3). I tried to flash PA 4.0-Alpha-201312050-ls980 with pa_gapps-modular-full-4.4.2-20131215. I'm not sure what went wrong and why I can't boot into recovery. Any information would be greatly appreciated, not sure if this is the right place to ask for help, thank you for your time. For some reason I can't find the thread now... God I'm an idiot. Any help would be greatly appreciated.
Try getting into download mode volume up and plug into computer
Or
Press and hold power and volume down until the LG logo, let go, then press and hold again for recovery
datechnerd said:
Try getting into download mode volume up and plug into computer
Or
Press and hold power and volume down until the LG logo, let go, then press and hold again for recovery
Click to expand...
Click to collapse
I couldn't get into recovery. I can get into download mode. It says Firmware Update Do not unplug. Stuck at 0%.
Please tell me I am not screwed... I have no idea what happened to my recovery. I figured if anything happened like this I could always boot into recovery and restore to stock. I'm honestly about to freak out...
AusernameIwillnotremember said:
I couldn't get into recovery. I can get into download mode. It says Firmware Update Do not unplug. Stuck at 0%.
Please tell me I am not screwed... I have no idea what happened to my recovery. I figured if anything happened like this I could always boot into recovery and restore to stock.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2432476
datechnerd said:
http://forum.xda-developers.com/showthread.php?t=2432476
Click to expand...
Click to collapse
Thank you so much... I'm such a noob scrub.
AusernameIwillnotremember said:
Thank you so much... I'm such a noob scrub.
Click to expand...
Click to collapse
You're welcome
datechnerd said:
http://forum.xda-developers.com/showthread.php?t=2432476
Click to expand...
Click to collapse
Hey I'm having a little trouble installing the drivers, it says there's a more up to date version already installed. I went to device manager and found my device, clicked properties and uninstalled the drivers. However when I try to install the ones in the guide you linked it still says they are there. Any clue how to remove them?
device manager, right click phone, update drivers, browse computer, let me pick from a list, unclick show compatible hardware, and find LGE or LG and pick the driver that makes sense
datechnerd said:
device manager, right click phone, update drivers, browse computer, let me pick from a list, unclick show compatible hardware, and find LGE or LG and pick the driver that makes sense
Click to expand...
Click to collapse
Ok I clicked "Let me pick a list of device drivers on my computer" .... uncheck show compatible. I do not see and LG or LGE in here though.
My options are
(Enhance Storage Device)
(Standard MTP Device)
(Standard MTP-Compliant Device)
(Standard MTP-compliant devices)
(WPD enhanced storage device)
Microsoft
AusernameIwillnotremember said:
Ok under device manager I see Portable Devices > MTP USB Device. Is this my phone? It's not letting my navigate or choose the driver in that guide...
Click to expand...
Click to collapse
unless you have any other devices plugged in, like mp3 player or another phone, that's probably your phone
right click the MTP USB Device and follow previously mentioned steps
datechnerd said:
unless you have any other devices plugged in, like mp3 player or another phone, that's probably your phone
right click the MTP USB Device and follow previously mentioned steps
Click to expand...
Click to collapse
Sorry that was a stupid question and I replied too fast and didn't fully follow your directions, I can't find any LG or LGE under the let me pick list. I have unchecked show compatible. I'll make sure to click that THanks button every time too, thank you so much for helping me out.
AusernameIwillnotremember said:
Sorry that was a stupid question and I replied too fast and didn't fully follow your directions, I can't find any LG or LGE under the let me pick list. I have unchecked show compatible. I'll make sure to click that THanks button every time too, thank you so much for helping me out.
Click to expand...
Click to collapse
http://tool.xcdn.gdms.lge.com/dn/downloader.dev?fileKey=UW00120120425 try these drivers then those steps if it doesn't automatically
datechnerd said:
http://tool.xcdn.gdms.lge.com/dn/downloader.dev?fileKey=UW00120120425 try these drivers then those steps if it doesn't automatically
Click to expand...
Click to collapse
Alright I downloaded those drivers and repeated the steps (device manager, update software, choose from list, uncheck compatible) and nothing with LG or LGE popped up. I decided to just try to install them anyway and it seems to work. I'll resume following the original guide you linked and assume that these drivers will work. I'll probably come back shortly with more questions but hopefully I'll get it this time.
datechnerd said:
http://tool.xcdn.gdms.lge.com/dn/downloader.dev?fileKey=UW00120120425 try these drivers then those steps if it doesn't automatically
Click to expand...
Click to collapse
Ok I'm still having trouble, I installed the LG drivers you linked, installed LG FLash tools and didn't run (like it says in the guide), extracted TOT to desktop. I put the phone into download mode then it immediate goes into "Firmware Update" and it is stuck at 0%. In the guide it says it should initialize and load up drivers and I should see LG device under Device Manager. I do not see any device now. Maybe I need to use the old drivers in the guide?
AusernameIwillnotremember said:
Ok I'm still having trouble, I installed the LG drivers you linked, installed LG FLash tools and didn't run (like it says in the guide), extracted TOT to desktop. I put the phone into download mode then it immediate goes into "Firmware Update" and it is stuck at 0%. In the guide it says it should initialize and load up drivers and I should see LG device under Device Manager. I do not see any device now.
Click to expand...
Click to collapse
is it under ports and serial or something like that?
datechnerd said:
is it under ports and serial or something like that?
Click to expand...
Click to collapse
No. I unplugged it and plugged it back in and reinstalled the drivers you linked. I can now see it under devices as an LGE Android Phone. I booted into download mode and it's not initializing or installing drivers... I'm not sure what to do now.
datechnerd said:
is it under ports and serial or something like that?
Click to expand...
Click to collapse
I'll detail each step I've done
Install
1. Install the LG drivers downloaded above. Installed the drivers you gave me.
2. Install LGFlashTools v1.6 (but don't run it) Check
3. Extract the TOT file from the ZIP Check
Drivers initialization
1. Put the phone into download mode. (Turn off device PRESS VOL UP while plugging in the micro usb cable. If this doesn't work, try holding both volume keys instead) Check
2. Let the phone initialize and install the drivers. Once done, in Device manager, you should see the LG phone listed under COM ports (something along these lines). Doesn't initialize or install drivers! As I am typing this my device just disappeared from Device Manager, however, LGE AndroidNet USB Seriel Port (com4) has popped up
3. Find that LG entry in Device Manager, click on Properties, Advanced and then change the COM port to COM41 and close/save.
4. Unplu
AusernameIwillnotremember said:
No. I unplugged it and plugged it back in and reinstalled the drivers you linked. I can now see it under devices as an LGE Android Phone. I booted into download mode and it's not initializing or installing drivers... I'm not sure what to do now.
Click to expand...
Click to collapse
I'm quite stumped right, now. I'll keep looking
datechnerd said:
I'm quite stumped right, now. I'll keep looking
Click to expand...
Click to collapse
It's all good all of a sudden it appeared under ports! Now I'm trying to find an LG Flash tools serial number like it says in the guide but I cannot find one anywhere with a google search. However "free" lg flash tools appear on the top of the list. Not sure what to do here. I'll update where I'm at in the guide in a moment.
datechnerd said:
I'm quite stumped right, now. I'll keep looking
Click to expand...
Click to collapse
Ok here is where I am at.
4. Execute the LGFlashTools. It should ask you for a key, put it in. Now you should see a dialog where you can load the DLL file and the TOT files that you extracted earlier. Put them both in here. Click ok Check
Flashing
5. There is a yellow arrow on the top left. Click on it to initialize the process. Once done, it should say "ready/finished" or whatever. Clicked it and got this error "MilkyWay Control Port Open FAIL!!!."
6. Put the phone in download mode again, and plug it into the USB port. LG FLash Tools should start flashing it automatically. When it's done, it'll automatically reboot into your stock AT&T rom and all of your data and internal sdcard files are gone. Errors here too "Device Model is different!
Check Phone or DLL!
"
i have a bricked lg g2 d802t after ota update.
phone was recongnised from pc as qhsusb_bulk but after ubuntu method posted here Fix No recovery, download mode.. i think i made a mistake flashing boot partition?
now phone wont turn on, no download mode, recovery mode or anything else, but when connected to pc it shows qhsusb_bulk in the device manager, but the is still off and wont turn on.. do you have idea to fix this problem? please help me
anybody is experiencing the same state as i have? please help..
which partitions did you flash ?
bender_007 said:
which partitions did you flash ?
Click to expand...
Click to collapse
i only followed the instructions here and flashed the provided .img by the way im on official kitkat firmware, the provided .img is for jb right? do you think this can be still fix without going to service center? :crying:
scout1089 said:
i only followed the instructions here and flashed the provided .img by the way im on official kitkat firmware, the provided .img is for jb right? do you think this can be still fix without going to service center? :crying:
Click to expand...
Click to collapse
Flash only aboot, boot, laf. You need the d802T for aus i think.
bender_007 said:
Flash only aboot, boot, laf. You need the d802T for aus i think.
Click to expand...
Click to collapse
how can i do that? because i dont have download mode, nor the phone turns on, pc wont detect or recognize the phone anymore when connected, all i got is qhsusb_bulk in the device manager and no multiple drives shown in my computer like before, also ubuntu wont recognize nor detect it also.. :crying:
Try with knoppix m8.
bender_007 said:
Try with knoppix m8.
Click to expand...
Click to collapse
can you provide the link for the knoppix m8?
so im going to run this instead of ubuntu and follow the same instructions stated on the tutorial mentioned? and only flash the 3 .img aboot, boot, laf? am i right? so im going to extract the kdz in order to get the 3 .img specific to my device?
http://knoppix.net/get.php just the 3. Find your original kdz m8
bender_007 said:
http://knoppix.net/get.php just the 3. Find your original kdz m8
Click to expand...
Click to collapse
im going to extract the D802T kdz and get the 3 .img from it? sorry still a noob and could you please explain and guide me through?
edit: after booting with knoopix, inserted the phone still cant be read.. i found no biggest number and all numbers are the same 1-15, seems it did'nt detect the phone, please help
can someone else who manage to revive their phone help me?
please help
i didnt get it ..
ur pc recognize the device as qhsusb ? or doesnt recognize it at all ?
rotem11 said:
i didnt get it ..
ur pc recognize the device as qhsusb ? or doesnt recognize it at all ?
Click to expand...
Click to collapse
when connected to pc, it displays qhsusb_bulk in the device manager and nothing no multiple drives, the phone does not turn on but i think its on even though the screen looks dead because when i left it for an hour i felt the phone's battery is warm..
try go ubuntu and follow this guide http://forum.xda-developers.com/showthread.php?t=2681089
maozer said:
try go ubuntu and follow this guide http://forum.xda-developers.com/showthread.php?t=2681089
Click to expand...
Click to collapse
already did ubuntu wont detect the phone
can u try ubuntu with vmware?
maozer said:
can u try ubuntu with vmware?
Click to expand...
Click to collapse
im using the usb method, if the usb method didnt detect the phone so i guess the vmware wont too?
also tried knoppix it wont detect the phone's partition
well i had the exact same problem u have.. you can look at my previous posts..
i dont know why but it worked for me with vmware.. and in ur situation it worth a shoot.
one of the Initial Symptoms are qhsusb.. try it and let me know..
maozer said:
well i had the exact same problem u have.. you can look at my previous posts..
i dont know why but it worked for me with vmware.. and in ur situation it worth a shoot.
one of the Initial Symptoms are qhsusb.. try it and let me know..
Click to expand...
Click to collapse
okey i'll give it a shoot.. thank you
Please i messed up with my tab 4 [t337a]
I tried unlocking it using octopus box, it showed deactivating MSL. the tab turned off and didn't turn back on
Please help me. Thanks
merujeffrey said:
Please i messed up with the MSL
I to unlock it using octopus box, it showed deactivating MSL. the tab turned off and when came back up.
Please help me. Thanks
Click to expand...
Click to collapse
Could you elaborate on that please? Like what device? What's MSL etc.,
moonbutt74 said:
Could you elaborate on that please? Like what device? What's MSL etc.,
Click to expand...
Click to collapse
i tried network unlocking it with this http://octopusbox.com/
i don't really know what the MSL means.
but am pretty sure the software messed up with the partitions.
my pc detects it
it shows Qualcomm HS-USB QDLOADER 9008 in ports section in device manager.
bro can a debrick file solve my problem ???????
merujeffrey said:
bro can a debrick file solve my problem ???????
Click to expand...
Click to collapse
Does osin detect your device? If it does i would give a shot to that.... i mean it cant rly get any worse....
thelous said:
Does osin detect your device? If it does i would give a shot to that.... i mean it cant rly get any worse....
Click to expand...
Click to collapse
if u mean odin, no it doesn't detect.
m,
you're not going to get past secure boot or trustzone, you're best best is to contact att and request an official full firmware release.
m
Oh its att device.... nothing to do then rly...
Hey guys I just installed the full image of 7.1.2 beta 2 over top of beta 1 using Flashfire without the bootloader and modem selected and all went fine until I decided to use Flashfire to upgrade the bootloader and modem forgetting that we must use Fastboot as I am new to Flashfire and I was reading all through the beta thread before I did it and didn't understand we still must use Fastboot so anyways I am stuck in a hard brick now with the phone not powering on at all and can't do anything to restore it as my Windows 10 now detects the phone as unknown device (device descriptor request failed) is there anything I can do at this point as I just bought this phone used.
The error that I got in Flashfire was that the device storage is full when updating the bootloader as the modem went fine.
@rmorris003
You said the phone won't even power on. You mean no Google? Hold the power button down for a couple of minutes and see if it will reboot. If not put it on a charger, and after fully charging try the long press power button again. If you can get it to start, try to put it in fastboot mode. (ie. power+vol dn). If you can get to bootloader you can send fastboot commands and fix it. If you can get to this point, there are instructions here.
rmorris003 said:
Hey guys I just installed the full image of 7.1.2 beta 2 over top of beta 1 using Flashfire without the bootloader and modem selected and all went fine until I decided to use Flashfire to upgrade the bootloader and modem forgetting that we must use Fastboot as I am new to Flashfire and I was reading all through the beta thread before I did it and didn't understand we still must use Fastboot so anyways I am stuck in a hard brick now with the phone not powering on at all and can't do anything to restore it as my Windows 10 now detects the phone as unknown device (device descriptor request failed) is there anything I can do at this point as I just bought this phone used.
The error that I got in Flashfire was that the device storage is full when updating the bootloader as the modem went fine.
Click to expand...
Click to collapse
Hello... Well if your device is recognized as unknown, you could try to give this a shot:
https://forum.xda-developers.com/nexus-6p/general/howtos-debrick-nexus-6p-stuck-edl-9008-t3552838
Try to install Qualcomm driver first check the device manager. If you see your phone recognized as:
HS-USB QDLOADER 9008
You may be lucky!
Good luck...
5.1 said:
Hello... Well if your device is recognized as unknown, you could try to give this a shot:
https://forum.xda-developers.com/nexus-6p/general/howtos-debrick-nexus-6p-stuck-edl-9008-t3552838
Try to install Qualcomm driver first check the device manager. If you see your phone recognized as:
HS-USB QDLOADER 9008
You may be lucky!
Good luck...
Click to expand...
Click to collapse
I will try this when I get back from work, I just cant get my pc to see it as anything other than unknown device as it says this is the best driver for it.
rmorris003 said:
I will try this when I get back from work, I just cant get my pc to see it as anything other than unknown device as it says this is the best driver for it.
Click to expand...
Click to collapse
I see... There's a txt file in the driver folder. Follow its instructions.
Good luck...
5.1 said:
I see... There's a txt file in the driver folder. Follow its instructions.
Good luck...
Click to expand...
Click to collapse
I am stumped, I have disabled driver enforcement and can't get any drivers to see my phone so I am not sure what to do.
rmorris003 said:
I am stumped, I have disabled driver enforcement and can't get any drivers to see my phone so I am not sure what to do.
Click to expand...
Click to collapse
You disabled driver signature and rebooted your computer? Then installed Qualcomm drivers from the thread I linked you to? I think you have to reboot your computer once more...
Good luck...
I held the power and vol down and now it shows up under com ports so this is a good sign.
Ok got bootloader back and now put twrp on, I had to use qfil with nexus6p_fix_bricked but it got stuck at writing system.img but atleast the phone is on now.
Flashed the 7.1.2 beta 2 full image using the fastboot method included and all is back to normal.
Thanks so much for the help.
rmorris003 said:
Ok got bootloader back and now put twrp on, I had to use qfil with nexus6p_fix_bricked but it got stuck at writing system.img but atleast the phone is on now.
Flashed the 7.1.2 beta 2 full image using the fastboot method included and all is back to normal.
Thanks so much for the help.
Click to expand...
Click to collapse
Wow glad it worked for you... You might push the thanks button in the OP of the thread where you found the debrick tools and thanks @tenfar since he offered the solution. He already saved a few N6P devices. I only linked you to his thread which you could have found yourself anyway...
Cheers...
5.1 said:
Wow glad it worked for you... You might push the thanks button in the OP of the thread where you found the debrick tools and thanks @tenfar since he offered the solution. He already saved a few N6P devices. I only linked you to his thread which you could have found yourself anyway...
Cheers...
Click to expand...
Click to collapse
I'm pretty sure I was reading it before but I had to do some extensive reading on how to get the driver to read properly. I work night shift so I was kinda tired yesterday.
rmorris003 said:
I'm pretty sure I was reading it before but I had to do some extensive reading on how to get the driver to read properly. I work night shift so I was kinda tired yesterday.
Click to expand...
Click to collapse
You could report your experience in the other thread. Maybe it could help other users who faced the issue you had. :good:
Cheers...
rmorris003 said:
I'm pretty sure I was reading it before but I had to do some extensive reading on how to get the driver to read properly. I work night shift so I was kinda tired yesterday.
Click to expand...
Click to collapse
Hi there, I'm extremely new to Forums and the whole android scene please could you help?
I have the same issue with my Nexus 6P Hard bricked, only detected as a 9008 Port, no vibrations no power nothing!
I've tried to follow so many guides for the past three days however I've managed nothing. I've tried to do as you mentioned in the first posts, used the nexus6p_unbrick in Qfil but Sahara download fails.
Please Please Help, No Warranty just a Brick!
Clarkeofcurtis said:
Hi there, I'm extremely new to Forums and the whole android scene please could you help?
I have the same issue with my Nexus 6P Hard bricked, only detected as a 9008 Port, no vibrations no power nothing!
I've tried to follow so many guides for the past three days however I've managed nothing. I've tried to do as you mentioned in the first posts, used the nexus6p_unbrick in Qfil but Sahara download fails.
Please Please Help, No Warranty just a Brick!
Click to expand...
Click to collapse
I have the same exact problem, everytime i try to flash with qfil it says it can't connect to my COMPORT
Clarkeofcurtis said:
Hi there, I'm extremely new to Forums and the whole android scene please could you help?
I have the same issue with my Nexus 6P Hard bricked, only detected as a 9008 Port, no vibrations no power nothing!
I've tried to follow so many guides for the past three days however I've managed nothing. I've tried to do as you mentioned in the first posts, used the nexus6p_unbrick in Qfil but Sahara download fails.
Please Please Help, No Warranty just a Brick!
Click to expand...
Click to collapse
Falitheman said:
I have the same exact problem, everytime i try to flash with qfil it says it can't connect to my COMPORT
Click to expand...
Click to collapse
Hello,
Someone mentioned this in another post:
Hold volume up and plug the USB cord to.your computer and start qfil flash. Keep holding volume up until the flash ends...
Good luck...
5.1 said:
Hello,
Someone mentioned this in another post:
Hold volume up and plug the USB cord to.your computer and start qfil flash. Keep holding volume up until the flash ends...
Good luck...
Click to expand...
Click to collapse
So i have some good news...it connects now. it says start sending programmer but then it says download failed: unable to download flash programmer using sahara protocol and then it fails. Any help?:crying:
Falitheman said:
So i have some good news...it connects now. it says start sending programmer but then it says download failed: unable to download flash programmer using sahara protocol and then it fails. Any help?:crying:
Click to expand...
Click to collapse
Hey,
What version of qpst did you install?
Good luck...
5.1 said:
Hey,
What version of qpst did you install?
Good luck...
Click to expand...
Click to collapse
I am using 2.7.441
Update: It seemed to be working for a second but then it says download failed: qsahara server fail: process fail. Any idea what that means? I really need my phone back
Falitheman said:
I am using 2.7.441
Update: It seemed to be working for a second but then it says download failed: qsahara server fail: process fail. Any idea what that means? I really need my phone back
Click to expand...
Click to collapse
Hey,
Google qpst 2.7.453
It's easy to find. Scan the files on virustotal.com though.
Maybe the older versions are incompatible...
Good luck...
5.1 said:
Hey,
Google qpst 2.7.453
It's easy to find. Scan the files on virustotal.com though.
Maybe the older versions are incompatible...
Good luck...
Click to expand...
Click to collapse
I tried with the version you suggested and i got the same error i just had. Can you send me your version so i can see if that works?
Hi guys anyone can help me? My phone wont turn on after I Accidentally Installed a Custom Rom that doesnt support my phone. What should I do? Need help.
itsme.Ronjie said:
Hi guys anyone can help me? My phone wont turn on after I Accidentally Installed a Custom Rom that doesnt support my phone. What should I do? Need help.
Click to expand...
Click to collapse
Ok, in detail please tell me the steps you've taken and which custom rom specifically.
+)KEV1N(+ said:
Ok, in detail please tell me the steps you've taken and which custom rom specifically.
Click to expand...
Click to collapse
sir Kevin. I accidentally installed wrong ROM which is for Zen3 552kl on my Ze553kl. And now my phone wont boot. What should I do? Tried some QFIL and I get some errors "Sahara Failed"
itsme.Ronjie said:
sir Kevin. I accidentally installed wrong ROM which is for Zen3 552kl on my Ze553kl. And now my phone wont boot. What should I do? Tried some QFIL and I get some errors "Sahara Failed"
Click to expand...
Click to collapse
Are you able to boot into your bootloader?
(Hold power button + volume down while booting)
+)KEV1N(+ said:
Are you able to boot into your bootloader?
(Hold power button + volume down while booting)
Click to expand...
Click to collapse
I cant. Just black screen. No vibrations when holding the power button. But when i connect it to pc it shows QUALCOMM HS-USB 9008 QDLOADER 9008. Tried some QFIL but I getting some errors with Sahara Fail.
itsme.Ronjie said:
I cant. Just black screen. No vibrations when holding the power button. But when i connect it to pc it shows QUALCOMM HS-USB 9008 QDLOADER 9008. Tried some QFIL but I getting some errors with Sahara Fail.
Click to expand...
Click to collapse
Firstly, if I may ask, which ROM are you using?
Secondly, I believe the ROM provided in the following thread may be of help:
https://forum.xda-developers.com/zenfone-3-zoom/how-to/transfer-cn-rom-to-ww-rom-ze553kl-t3612990
You should be able to find the required files in that ROM.
If the program asks you for 3 files It should be in the following order:
Programmer file: prog_emmc_firehose_8953_ddr.mbn
Raw file: rawprogram0.xml
Patch file: patch0.xml
I won't be able to reply as much during weekdays, so if you need any consultancy, you can read from this thread:
https://forum.xda-developers.com/zenfone-2-laser/general/unbrick-guide-z00l-ze550kl-t3600527
I wish you best of luck with the unbricking process and I'll look forward to the results.
+)KEV1N(+ said:
Firstly, if I may ask, which ROM are you using?
Secondly, I believe the ROM provided in the following thread may be of help:
https://forum.xda-developers.com/zenfone-3-zoom/how-to/transfer-cn-rom-to-ww-rom-ze553kl-t3612990
You should be able to find the required files in that ROM.
If the program asks you for 3 files It should be in the following order:
Programmer file: prog_emmc_firehose_8953_ddr.mbn
Raw file: rawprogram0.xml
Patch file: patch0.xml
I won't be able to reply as much during weekdays, so if you need any consultancy, you can read from this thread:
https://forum.xda-developers.com/zenfone-2-laser/general/unbrick-guide-z00l-ze550kl-t3600527
I wish you best of luck with the unbricking process and I'll look forward to the results.
Click to expand...
Click to collapse
im using the WW ZE553KL Rom. I do have that 3 files but im getting an error in QFIL.
+)KEV1N(+ said:
Firstly, if I may ask, which ROM are you using?
Secondly, I believe the ROM provided in the following thread may be of help:
https://forum.xda-developers.com/zenfone-3-zoom/how-to/transfer-cn-rom-to-ww-rom-ze553kl-t3612990
You should be able to find the required files in that ROM.
If the program asks you for 3 files It should be in the following order:
Programmer file: prog_emmc_firehose_8953_ddr.mbn
Raw file: rawprogram0.xml
Patch file: patch0.xml
I won't be able to reply as much during weekdays, so if you need any consultancy, you can read from this thread:
https://forum.xda-developers.com/zenfone-2-laser/general/unbrick-guide-z00l-ze550kl-t3600527
I wish you best of luck with the unbricking process and I'll look forward to the results.
Click to expand...
Click to collapse
Still not fix ?
+)KEV1N(+ said:
Firstly, if I may ask, which ROM are you using?
Secondly, I believe the ROM provided in the following thread may be of help:
https://forum.xda-developers.com/zenfone-3-zoom/how-to/transfer-cn-rom-to-ww-rom-ze553kl-t3612990
You should be able to find the required files in that ROM.
If the program asks you for 3 files It should be in the following order:
Programmer file: prog_emmc_firehose_8953_ddr.mbn
Raw file: rawprogram0.xml
Patch file: patch0.xml
I won't be able to reply as much during weekdays, so if you need any consultancy, you can read from this thread:
https://forum.xda-developers.com/zenfone-2-laser/general/unbrick-guide-z00l-ze550kl-t3600527
I wish you best of luck with the unbricking process and I'll look forward to the results.
Click to expand...
Click to collapse
Still not fix :crying: