Database Users

Unbrick lg g3 qhsusb_bulk, qualcomm 9008 workking 100% by board ver 2.9a

How to Fix "error device not found in dload trying flash programmer" when use boardiag .
Lg g3 qualcomm 9008 when install driver then use tool boardiag fake tool say device not found in dload trying flash programmer
when you use tool fake board share in xda another tool say device not found in dload trying flash programmer. You need remove battery (of lg g2 hold power 1 minute) then connect cable again and use tool again
Sure install driver 100% wrong
With windowns 64 bit you need restart pc then click f8 choose disbable driver singturne....
Then remove battery (hold power 1 minute with lg g2) then connect cable try use tool unbrick >> sure done 100%
I will updload video error dload
Remember disbbale tool sony erricson if you have open tool in taskbar
How to fix “No response from the device. Check PMIC first and
if still boot problem, replace AP.”
Remove battery and connect again put qualcomm 9008 then use tool in topic
http://www.androidbrick.com/unbrick-recover-your-dead-lg-g3-all-variants/​ Just as helping
[*]I see very topic unbrick qualcomm 9008 lg g2, lg g3 but all tool can not use.
I have full tool board ver 2.9.( only 2.9).
Link download drive.google.xxx /file/d/0B_Hol5T47S-bYjNETmVPZkdWUms/view?usp=sharing (xxx= com)
Support lg g2, lg g3 workking 100%.
Download tool, open BoardDiag and choose file tot correct model phone of you( you can download tot in xda)
See guide in pictrure : very easy.
Note
Hold power 2 minute and connect cable ( or remove battery)>>And open tool check ap, emmc test again
Then unbrick done remove cable, hold power 30 second and hold volume up connect cable phone put downloadmod >> Use lgflashtool 1.5 flash file tot again >> done.
If done pls donate a few beers paypal of my Thank you very much.​

Man you saved my ass Thank you so much !1 when i get my salary ill donate to you and tell everybody to do so cuz this tool is amazing. im in download mode now ill try to flash with lg flash tool.

Thank so much man but my g3 last week unbrick qualcomm i had I submit for warranty[emoji24] [emoji24] I am very Star-crossed [emoji20]

Hello friend willcracker
Hello friend willcracker :good:
I hope all is well;
I saw this little tutorial so I want to ask for help
I have a LG G3 D855p and my phone is dead (bricked)
I can not quite understand the method you friend
not turn on my phone
I can not enter the "" Download Mode ""
VOL + Up when I connect the USB cable to the PC recognizes me as:
Qualcomm HS-USB QDLoader 9008 (COM10)
why I ask for help to revive my g3
If you help me ... .. I promise to donate something for you
you send a file "picture" attached
- - As I can get to "" Fastboot Mode "" on my phone
I hope your prompt response, please do not ignore my message :crying:
greetings from peru

You need to Disassemble Phone and Expose the TP Location
See pictrue
Expose the TP Location.
Done phone put qualcom 9008>> use tool unbrick
Remeber unplug battery connect only cable and short testpoint

Thanks for responding, but I need your help please friend
Hello willcracker I have no such tool you indicate "tool unbrick testpoint"
I could do this step with some type of cable or wire?
- If you Might tell me how to do that step with another option
leave your email. to chat google chat (Houngts) and you help me please
I'm worried because my g3 d855p not light, or anything like I said ....
await your prompt response, I hope you can help me

TOT Firmware, must match installed version?
Hey, thanks for providing this tool!
Final question, the TOT file must this match the installed version?
My situation:
Lollipop was installed, goal was to move to a custom rom (blisspop v2.3)
Rooting was successful
Install of twrp not, reboot into recovery caused the 'signature verification error'
Tried to flash the kitkat rom via the download method, failed, ...
Currently, I have the same verification error also when trying to get into download mode and have the Qualcomm HS-USB QDLoader 9008 in my device manager.
I have the LGD855AT-00-V10e-EUR-XX-JUL-08-2014-16G+0.tot file and did the first step of your procedure. Can I do the second step with this extract of kitkat even if lollipop was installed?
any feedback greatly appreciated!

Hello willcracker thanks, thanks for reply but I need your help please
Hello friend willcracker not have any of those tools indicated in its response = "testpoint tool unbrick"
I can do this step with some type of cable or wire
- I want you to guide me step by step how to perform the process
**will commit without any error.
And haci get my phone g3 ... haci I could also help others or siblings who need help to solve any problem with the g3
- I can not enter download mode
- I can not enter recovery mode
- When I turn on my phone, get the LG logo goes about three letters at the top left, then flashes a red, blue lights ...
- The PC recognizes me as Qualcomm HS-USB QDLoader 9008 (COM10)
You could leave your email. Google to chat chat (Houngts) and help me please
*....
Waiting for your prompt response, I hope you can help me
Please do not ignore my message willcracker friend
Greetings from Peru

themusic1510 said:
Hello friend willcracker not have any of those tools indicated in its response = "testpoint tool unbrick"
I can do this step with some type of cable or wire
- I want you to guide me step by step how to perform the process
Greetings from Peru
Click to expand...
Click to collapse
NO you need find google how do short testpoint samsung n7100 you see they guide short testpoint . Lg when short testpoint phone detect qualcomm 9008
And you use tool board diag unbrick.

???
themusic1510 said:
Hello friend willcracker not have any of those tools indicated in its response = "testpoint tool unbrick"
I can do this step with some type of cable or wire
- I want you to guide me step by step how to perform the process
**will commit without any error.
And haci get my phone g3 ... haci I could also help others or siblings who need help to solve any problem with the g3
- I can not enter download mode
- I can not enter recovery mode
- When I turn on my phone, get the LG logo goes about three letters at the top left, then flashes a red, blue lights ...
- The PC recognizes me as Qualcomm HS-USB QDLoader 9008 (COM10)
You could leave your email. Google to chat chat (Houngts) and help me please
*....
Waiting for your prompt response, I hope you can help me
Please do not ignore my message willcracker friend
Greetings from Peru
Click to expand...
Click to collapse
I'm in the same boat! Could you please explain it a little better?

frank.devliegher said:
Hey, thanks for providing this tool!
Final question, the TOT file must this match the installed version?
My situation:
any feedback greatly appreciated!
Click to expand...
Click to collapse
You need extract file tot d855 and put phone to qualcomm 9008 and unbrick . DOne flash stock rom. Find rom 5.01 link another

Ahh now i see!
Well ive tryed this guide with two different computers, but all i get is ap check failed, i do get into qualcomm mode and everything. Why does it fail!!? Am i doing something wrong?

@willcracker
The link doesnt work !? Where can i download the BoardDiagTool?
I have a F240L and this totfile BIN_LGE980AT-00-V20g-ATT-US-APR-28-2014+0 .Can I use it?
I have tried with this file but i get the message AP Check or Check PMIC first

sourly64 said:
@willcracker
The link doesnt work !? Where can i download the BoardDiagTool?
I have a F240L and this totfile BIN_LGE980AT-00-V20g-ATT-US-APR-28-2014+0 .Can I use it?
I have tried with this file but i get the message AP Check or Check PMIC first
Click to expand...
Click to collapse
what do you mean?
The link unbrick only g2 g3 and gpro2
Phone of you G pro i not upload tool . Unsderstand.

Magnerion said:
Well ive tryed this guide with two different computers, but all i get is ap check failed, i do get into qualcomm mode and everything. Why does it fail!!? Am i doing something wrong?
Click to expand...
Click to collapse
Model Lg d851? writh
rememer ber tool suppoer only lg g3 f400s/l/k , lg d855 16gb and 32gb.
If use tool say error pcmic on tool not support (Ex: lg d851)
I up load only msm8974ac g3 msm8975ac g3 no upload

Magnerion said:
Well ive tryed this guide with two different computers, but all i get is ap check failed, i do get into qualcomm mode and everything. Why does it fail!!? Am i doing something wrong?
Click to expand...
Click to collapse
It seems won't work.I have gone through about this problem.Alway AP Check fail.QPST reported that phone had been in Sahara download mode for few seconds.A RMA fix my phone.But it cost me about 50dollars

willcracker said:
what do you mean?
The link unbrick only g2 g3 and gpro2
Phone of you G pro i not upload tool . Unsderstand.
Click to expand...
Click to collapse
Hello willcracker !
Thanks for the note,do you know the totfile is the right one ?
I get with this file ,when is extraced the message in BoardDiag Check PMIC first and if not boot Check AP

TOT Version
willcracker said:
You need extract file tot d855 and put phone to qualcomm 9008 and unbrick . DOne flash stock rom. Find rom 5.01 link another
Click to expand...
Click to collapse
I have a TOT file, but for kitkat, not Lollipop. Can I use this TOT file?
(have only a kdz file for lollipop)
Thx!

frank.devliegher said:
I have a TOT file, but for kitkat, not Lollipop. Can I use this TOT file?
(have only a kdz file for lollipop)
Thx!
Click to expand...
Click to collapse
YES you can use tot kikat unbrick .

sourly64 said:
Hello willcracker !
Thanks for the note,do you know the totfile is the right one ?
I get with this file ,when is extraced the message in BoardDiag Check PMIC first and if not boot Check AP
Click to expand...
Click to collapse
sr i have not upload hex lg gpro waitting comming soon.

Soft-bricked oneplus two, getting Sahara error

Hey
I done messed up...
I can only boot into fastboot and when following almost every guide for un-bricking my phone I get a 'Sahara' error (can't link cause my acc is new).
Under Device Management the port is: QUALCOMM-HS USB Diagnostics 9008
Every guide says it should be 9006 (excluding oneplus' guide).
Can someone help me?

did you find the solution? I've got into the same problem...

Delphir said:
did you find the solution? I've got into the same problem...
Click to expand...
Click to collapse
Please elaborate

NOTE: When the tool gives the "Sahara error", DON'T DISCONNECT THE PHONE from your PC, and press vol up and power button. It maybe seem stupid as a fix but generally it works.
Click to expand...
Click to collapse
try this methode, it's from unbrick guide of the OnePlus 5, it may work for you

Hard bricked lg l fino (d295)

I can't do anything with my phone and when I connect it to the PC, it is shown as relink hs-usb qdloader 9008. Can anyone help me with this? please

Hey. Try following this thread and tell me if it worked!

proudlytm said:
Hey. Try following this thread and tell me if it worked!
Click to expand...
Click to collapse
Don't work
Nothing work...:crying:

proudlytm said:
Hey. Try following this thread and tell me if it worked!
Click to expand...
Click to collapse
Hi. I tried to follow everything as instructed and I was able to extract the files but when I was about to click the start button to run the tests, a pop-up appeared saying "partition.txt does not exist. Please extract the file from the total binary image".
What should I do to solve this? And when I try to open the device manager, my device is still detected as QHSUSB_BULK. Please help me with this

alexandria2812 said:
Hi. I tried to follow everything as instructed and I was able to extract the files but when I was about to click the start button to run the tests, a pop-up appeared saying "partition.txt does not exist. Please extract the file from the total binary image".
What should I do to solve this? And when I try to open the device manager, my device is still detected as QHSUSB_BULK. Please help me with this
Click to expand...
Click to collapse
I have no idea man.. Ask the OP of the thread for help.. Also, I don't have this phone anymore because it broke and now I am using a new one.

[Hard Brick] Nexus 6P 7.1.2 Beta 2 [Solved]

Hey guys I just installed the full image of 7.1.2 beta 2 over top of beta 1 using Flashfire without the bootloader and modem selected and all went fine until I decided to use Flashfire to upgrade the bootloader and modem forgetting that we must use Fastboot as I am new to Flashfire and I was reading all through the beta thread before I did it and didn't understand we still must use Fastboot so anyways I am stuck in a hard brick now with the phone not powering on at all and can't do anything to restore it as my Windows 10 now detects the phone as unknown device (device descriptor request failed) is there anything I can do at this point as I just bought this phone used.
The error that I got in Flashfire was that the device storage is full when updating the bootloader as the modem went fine.

@rmorris003
You said the phone won't even power on. You mean no Google? Hold the power button down for a couple of minutes and see if it will reboot. If not put it on a charger, and after fully charging try the long press power button again. If you can get it to start, try to put it in fastboot mode. (ie. power+vol dn). If you can get to bootloader you can send fastboot commands and fix it. If you can get to this point, there are instructions here.

rmorris003 said:
Hey guys I just installed the full image of 7.1.2 beta 2 over top of beta 1 using Flashfire without the bootloader and modem selected and all went fine until I decided to use Flashfire to upgrade the bootloader and modem forgetting that we must use Fastboot as I am new to Flashfire and I was reading all through the beta thread before I did it and didn't understand we still must use Fastboot so anyways I am stuck in a hard brick now with the phone not powering on at all and can't do anything to restore it as my Windows 10 now detects the phone as unknown device (device descriptor request failed) is there anything I can do at this point as I just bought this phone used.
The error that I got in Flashfire was that the device storage is full when updating the bootloader as the modem went fine.
Click to expand...
Click to collapse
Hello... Well if your device is recognized as unknown, you could try to give this a shot:
https://forum.xda-developers.com/nexus-6p/general/howtos-debrick-nexus-6p-stuck-edl-9008-t3552838
Try to install Qualcomm driver first check the device manager. If you see your phone recognized as:
HS-USB QDLOADER 9008
You may be lucky!
Good luck...

5.1 said:
Hello... Well if your device is recognized as unknown, you could try to give this a shot:
https://forum.xda-developers.com/nexus-6p/general/howtos-debrick-nexus-6p-stuck-edl-9008-t3552838
Try to install Qualcomm driver first check the device manager. If you see your phone recognized as:
HS-USB QDLOADER 9008
You may be lucky!
Good luck...
Click to expand...
Click to collapse
I will try this when I get back from work, I just cant get my pc to see it as anything other than unknown device as it says this is the best driver for it.

rmorris003 said:
I will try this when I get back from work, I just cant get my pc to see it as anything other than unknown device as it says this is the best driver for it.
Click to expand...
Click to collapse
I see... There's a txt file in the driver folder. Follow its instructions.
Good luck...

5.1 said:
I see... There's a txt file in the driver folder. Follow its instructions.
Good luck...
Click to expand...
Click to collapse
I am stumped, I have disabled driver enforcement and can't get any drivers to see my phone so I am not sure what to do.

rmorris003 said:
I am stumped, I have disabled driver enforcement and can't get any drivers to see my phone so I am not sure what to do.
Click to expand...
Click to collapse
You disabled driver signature and rebooted your computer? Then installed Qualcomm drivers from the thread I linked you to? I think you have to reboot your computer once more...
Good luck...

I held the power and vol down and now it shows up under com ports so this is a good sign.

Ok got bootloader back and now put twrp on, I had to use qfil with nexus6p_fix_bricked but it got stuck at writing system.img but atleast the phone is on now.
Flashed the 7.1.2 beta 2 full image using the fastboot method included and all is back to normal.
Thanks so much for the help.

rmorris003 said:
Ok got bootloader back and now put twrp on, I had to use qfil with nexus6p_fix_bricked but it got stuck at writing system.img but atleast the phone is on now.
Flashed the 7.1.2 beta 2 full image using the fastboot method included and all is back to normal.
Thanks so much for the help.
Click to expand...
Click to collapse
Wow glad it worked for you... You might push the thanks button in the OP of the thread where you found the debrick tools and thanks @tenfar since he offered the solution. He already saved a few N6P devices. I only linked you to his thread which you could have found yourself anyway...
Cheers...

5.1 said:
Wow glad it worked for you... You might push the thanks button in the OP of the thread where you found the debrick tools and thanks @tenfar since he offered the solution. He already saved a few N6P devices. I only linked you to his thread which you could have found yourself anyway...
Cheers...
Click to expand...
Click to collapse
I'm pretty sure I was reading it before but I had to do some extensive reading on how to get the driver to read properly. I work night shift so I was kinda tired yesterday.

rmorris003 said:
I'm pretty sure I was reading it before but I had to do some extensive reading on how to get the driver to read properly. I work night shift so I was kinda tired yesterday.
Click to expand...
Click to collapse
You could report your experience in the other thread. Maybe it could help other users who faced the issue you had. :good:
Cheers...

rmorris003 said:
I'm pretty sure I was reading it before but I had to do some extensive reading on how to get the driver to read properly. I work night shift so I was kinda tired yesterday.
Click to expand...
Click to collapse
Hi there, I'm extremely new to Forums and the whole android scene please could you help?
I have the same issue with my Nexus 6P Hard bricked, only detected as a 9008 Port, no vibrations no power nothing!
I've tried to follow so many guides for the past three days however I've managed nothing. I've tried to do as you mentioned in the first posts, used the nexus6p_unbrick in Qfil but Sahara download fails.
Please Please Help, No Warranty just a Brick!

Clarkeofcurtis said:
Hi there, I'm extremely new to Forums and the whole android scene please could you help?
I have the same issue with my Nexus 6P Hard bricked, only detected as a 9008 Port, no vibrations no power nothing!
I've tried to follow so many guides for the past three days however I've managed nothing. I've tried to do as you mentioned in the first posts, used the nexus6p_unbrick in Qfil but Sahara download fails.
Please Please Help, No Warranty just a Brick!
Click to expand...
Click to collapse
I have the same exact problem, everytime i try to flash with qfil it says it can't connect to my COMPORT

Clarkeofcurtis said:
Hi there, I'm extremely new to Forums and the whole android scene please could you help?
I have the same issue with my Nexus 6P Hard bricked, only detected as a 9008 Port, no vibrations no power nothing!
I've tried to follow so many guides for the past three days however I've managed nothing. I've tried to do as you mentioned in the first posts, used the nexus6p_unbrick in Qfil but Sahara download fails.
Please Please Help, No Warranty just a Brick!
Click to expand...
Click to collapse
Falitheman said:
I have the same exact problem, everytime i try to flash with qfil it says it can't connect to my COMPORT
Click to expand...
Click to collapse
Hello,
Someone mentioned this in another post:
Hold volume up and plug the USB cord to.your computer and start qfil flash. Keep holding volume up until the flash ends...
Good luck...

5.1 said:
Hello,
Someone mentioned this in another post:
Hold volume up and plug the USB cord to.your computer and start qfil flash. Keep holding volume up until the flash ends...
Good luck...
Click to expand...
Click to collapse
So i have some good news...it connects now. it says start sending programmer but then it says download failed: unable to download flash programmer using sahara protocol and then it fails. Any help?:crying:

Falitheman said:
So i have some good news...it connects now. it says start sending programmer but then it says download failed: unable to download flash programmer using sahara protocol and then it fails. Any help?:crying:
Click to expand...
Click to collapse
Hey,
What version of qpst did you install?
Good luck...

5.1 said:
Hey,
What version of qpst did you install?
Good luck...
Click to expand...
Click to collapse
I am using 2.7.441
Update: It seemed to be working for a second but then it says download failed: qsahara server fail: process fail. Any idea what that means? I really need my phone back

Falitheman said:
I am using 2.7.441
Update: It seemed to be working for a second but then it says download failed: qsahara server fail: process fail. Any idea what that means? I really need my phone back
Click to expand...
Click to collapse
Hey,
Google qpst 2.7.453
It's easy to find. Scan the files on virustotal.com though.
Maybe the older versions are incompatible...
Good luck...

5.1 said:
Hey,
Google qpst 2.7.453
It's easy to find. Scan the files on virustotal.com though.
Maybe the older versions are incompatible...
Good luck...
Click to expand...
Click to collapse
I tried with the version you suggested and i got the same error i just had. Can you send me your version so i can see if that works?

UnBrick

Hi everyone. Need some help.
How can i unbrick my ZenFone Max Pro M2 (ZB631KL)
Issues - after programm stuck, phone was restarted, and then - Black screen, zero reaction. No indication.
PC show's - qualcomm hs-usb qdloader 9008.
I tried QFIL with [firmware27]ZQL1820_Factory_201812071630_ChangeFlash.zip
But failed. Always one of two errors
1. sahara_rx_data:276:Unable to read packet header. Only read 0 bytes
2. Download Fail:FireHose Fail:FHLoader Fail: File dosn't exist.
What i can do without hardware flash ?
Thank for answers!

Closed. I done it. Phone is alive

How did u do that..can u pls tell me

antizack said:
Hi everyone. Need some help.
How can i unbrick my ZenFone Max Pro M2 (ZB631KL)
Issues - after programm stuck, phone was restarted, and then - Black screen, zero reaction. No indication.
PC show's - qualcomm hs-usb qdloader 9008.
I tried QFIL with [firmware27]ZQL1820_Factory_201812071630_ChangeFlash.zip
But failed. Always one of two errors
1. sahara_rx_data:276:Unable to read packet header. Only read 0 bytes
2. Download Fail:FireHose Fail:FHLoader Fail: File dosn't exist.
What i can do without hardware flash ?
Thank for answers!
Click to expand...
Click to collapse
Pls share your knowledge to us master :[

1. Use QPST. QFIL without QPST will not work. U'll get error (File not found or file not exist)
2. Use QPST v 2.7.495
With 2.7.496 i was getting error - 0 bytes readed
3. Important. Use windows 7. I don't know why - a wasn't able to flash on win 10 with USB 2.0 port or usb-hub.

I currently have Win 8.1, I think I'll try with that, if it doesn't work, I can always make a new partition and install win 7 there. Anyway I have never heard of QPST and QFIL, so I'll do some researches on that.
Thank you for your time, we really appreciate. I'll let you know if I manage to unbrick my device.

Be careful. When u'll flash, don't forget to check couple times all settings in QFIL.
I'm talking about xml files.

antizack said:
Be careful. When u'll flash, don't forget to check couple times all settings in QFIL.
I'm talking about xml files.
Click to expand...
Click to collapse
I don't understand where I have to get the files I need. I saw I need the firmware, I guess, but I don't understand what's up with the XML file. Where did you get them? Sorry if I'm disturbing you again.

NoobNotMaster69 said:
I don't understand where I have to get the files I need. I saw I need the firmware, I guess, but I don't understand what's up with the XML file. Where did you get them? Sorry if I'm disturbing you again.
Click to expand...
Click to collapse
Hello colleague, I also have the same problem, I tried some programs, but they didn't work, but I still haven't tried this QPST_2.7.495, but I need the flash, because I deleted the ones I had here. if you found it, give me the link.