could not do normal boot.
ODIN MODE.
Product name: SM-N9006
Current Binary: Custom
Reactivitation lock(KK): OFF
KNOX KEANEL LOCK : 0X 0
KNOX WARRANTY VOID : 0 X1
QUALCOMM SECUREBOOT: ENABLE(CSB)
AP SWAEV: S2, T2, R2, A3, P2
WRITE PROTECTION : Enable
UBC START
Downloading....
Do not turn off target
- download KINGO to root it, and it show success
- download root checker shown not rooted
- then download odin ver 3.7 and tried to do that and failed
- then it came to recovery mode, I press wipe all data and then reboot
- then shown firmware upgrade, and use kies
- I use kies but cannot detect this phone
- then use odin ver 3.9 and now it became this
then i restart and battery take out , and for whole day.. no seem to load.
and
i tried using pressing VOL DOWN + HOME + POWER
it came to Chinese wording.. with WARNING
. (I TRANSLATE IN ENGLISH AS WRITTEN IN CHINESE)
custom , modify or downloading can cause great problem to the software function.
if required our technical support, required to pay.
if you insist want to download default system function, please
VOL UP , if not VOL DOWN to cancel.
VOL UP
: CONTINUE
VOL DOWN
: CANCEL ( RECOVERY)
anyone can help, i', reside in Singapore and this is a china NOTE 3,
and the version is 4.42 KIT KAT version.
MODEL : NOTE 3, SM-N9
PLEASE HELP, MY EMAIL ADDRESS: [email protected] really appreciate.. thank you
ODIN MODE ( Could not do normal boot) SM9006
could not do normal boot.
ODIN MODE.
Product name: SM-N9006
Current Binary: Custom
Reactivitation lock(KK): OFF
KNOX KEANEL LOCK : 0X 0
KNOX WARRANTY VOID : 0 X1
QUALCOMM SECUREBOOT: ENABLE(CSB)
AP SWAEV: S2, T2, R2, A3, P2
WRITE PROTECTION : Enable
UBC START
Downloading....
Do not turn off target
- download KINGO to root it, and it show success
- download root checker shown not rooted
- then download odin ver 3.7 and tried to do that and failed
- then it came to recovery mode, I press wipe all data and then reboot
- then shown firmware upgrade, and use kies
- I use kies but cannot detect this phone
- then use odin ver 3.9 and now it became this
then i restart and battery take out , and for whole day.. no seem to load.
and
i tried using pressing VOL DOWN + HOME + POWER
it came to Chinese wording.. with WARNING
. (I TRANSLATE IN ENGLISH AS WRITTEN IN CHINESE)
custom , modify or downloading can cause great problem to the software function.
if required our technical support, required to pay.
if you insist want to download default system function, please
VOL UP , if not VOL DOWN to cancel.
VOL UP
: CONTINUE
VOL DOWN
: CANCEL ( RECOVERY)
once I press UP , this came to ODIN MODE page without could not do normal boot.
but it cannot not loading. and struck at the page..
I tried to press again with VOL UP + HOME + POWER
it came to this page
Andriod. system recovery <3E>
KOT49.HN9006ZNUENH1
Volume up/down to move highlight;
power button to select.
reboot system now
apply update from ADB
apply update from external storage
wipe data/factory reset
wipe cache partition
apply update from cache
below written
#MANUAL MODE #
--Appling Multi-CSC...
Applied the CSC-code : CHN
Successfully applied multi-CSC.[?COLOR]
anyone can help, i reside in Singapore and this is a china NOTE 3,
and the version is 4.42 KIT KAT version.
MODEL : NOTE 3, SM-N9
PLEASE HELP, MY EMAIL ADDRESS: [email protected] really appreciate.. thank you
MODEL: NOTE 3 SM-N9006
CHINA NOTE 3
VERSION: KITKAT 4.4.2
and I tried download kies in Singapore, US and even China ..cannot detect,
whatever I tried, it automatically came to the odin mode cannot do normal reboot.
and in recovery mode I pressed VOL UP + HOME + POWER still go back to odin mode...
anyone can help me with it.
PLEASE HELP, MY EMAIL ADDRESS: [email protected] really appreciate.. thank you
[/QUOTE]
ciny said:
could not do normal boot.
ODIN MODE.
Product name: SM-N9006
Current Binary: Custom
Reactivitation lock(KK): OFF
KNOX KEANEL LOCK : 0X 0
KNOX WARRANTY VOID : 0 X1
QUALCOMM SECUREBOOT: ENABLE(CSB)
AP SWAEV: S2, T2, R2, A3, P2
WRITE PROTECTION : Enable
UBC START
Downloading....
Do not turn off target
- download KINGO to root it, and it show success
- download root checker shown not rooted
- then download odin ver 3.7 and tried to do that and failed
- then it came to recovery mode, I press wipe all data and then reboot
- then shown firmware upgrade, and use kies
- I use kies but cannot detect this phone
- then use odin ver 3.9 and now it became this
then i restart and battery take out , and for whole day.. no seem to load.
and
i tried using pressing VOL DOWN + HOME + POWER
it came to Chinese wording.. with WARNING
. (I TRANSLATE IN ENGLISH AS WRITTEN IN CHINESE)
custom , modify or downloading can cause great problem to the software function.
if required our technical support, required to pay.
if you insist want to download default system function, please
VOL UP , if not VOL DOWN to cancel.
VOL UP
: CONTINUE
VOL DOWN
: CANCEL ( RECOVERY)
anyone can help, i', reside in Singapore and this is a china NOTE 3,
and the version is 4.42 KIT KAT version.
MODEL : NOTE 3, SM-N9
PLEASE HELP, MY EMAIL ADDRESS: [email protected] really appreciate.. thank you
Click to expand...
Click to collapse
G'day
I had the exact same issue with my SM-G900I. With the suggestion from an XDA senior; Try flashing with stock firmware from samsmobile.com for your particular model with Odin.
Trying this suggestion as I respond to your predicament. Shall keep you posted on the outcome.
Peace. :what:
Sent from my PNDPP47GP using XDA Free mobile app
Hi, I've just recently switched over from iphone to android so I'm still new to the whole system. Anyway I've been trying to root my phone for the past 2 days to no avail so I'm at my wits end here. Before I start my phone is from korea which I don't know if whether or not impacts its ability to be rooted, I've done all the basics like enable USB debugging from dev mode, install samsung usb drivers, open ODIN in admin mode and allow MTP to computer. My Device details are below:
>Baseband version : G906SKSU1CPF1
>KERNEL : 3.10.40-8533426
>BUILD NUMBER : MMB29M.G906SKSU1CPF3
So anyway I first tried flashing using CF autoroot for sm-G906S with odin which while it said it was passed and was successful on pc it would be stuck on the samsung logo with a message at the top left that said :
>Recovery booting
>Recovery is not seandroid enforcing
>set warranty bit recovery
So then I tried flashing TWRP custom recovery and putting Super user zip in the internal storage which although got my phone back to working order still wouldnt let me root as the process required me to go to recovery mode from the fastboot mode after it was done flashing (I tried both with and without autoreboot), however once the flashing was done on fastboot I couldn't get to recovery mode no matter how long I held the Vol up/power/home button combination and when i tried it after rebooting it would show normal recovery mode hence there was no way to install the Super User. (Also attempted this with phils recovery)
I then tried to do the TWRP method using adb with command prompt however it would get stuck saying waiting for device when i tried to flash and needless to say kingroot also failed.
At this point as far I've gone through all the methods I could find for my particular device. Would greatly appreciate any insight or advice regarding this problem.
Thanks
start reading from here http://forum.xda-developers.com/gal...ner-thread-t2807639/post68725608#post68725608
Earlier it was running on custom rom then i tried to install stock rom on my device moto g4 plus...nd i successfully installed it....later an update came and as soon as phone dowoaded update nd gone to reboot doesn't turn on after that...nothing of the screen ..only charging led blinking .....nd today i tried to do blankflash nd it was successful nd something showed up on the screen for the first time
it has these options :
start
restart bootloader
recovery mode
power off
factory
barcodes
bp tools
qcom
bootloader logs
switch tools mode
when i select recovery mode..it shows up this:
------------------------------------------------------------------
Startup failed :
your device didnt start up succesfully.
use the software repair assistant on computer to repair your device.
Ap Fastboot Mode(secure)
Fastboot Reason: Failed to intialise storage partition table
ERROR : No bootaimage found . skip to fastboot
boot up failed.
---------------------------------------------------------------------
please help me through this...i want to install stock android on my phone
Try this guide https://forum.xda-developers.com/moto-g4-plus/how-to/stock-rom-npjs25-93-14-4-march-1-t3608138
Your device's memory seems to be corrupted, so it doesn't recognize a recovery being present. As pointed out above, go back to Fastboot, and install the latest stock ROM.
Hi everyone
I am posting this because I fail to flash TWRP on my LG G2 (D802, 30c); I would like to flash LineageOS. I have read many guides and posts - however, none worked. So I turn to you for advice -- would you help me, please?
I have managed to flash Cyanogen to my Samsung S2 a few years ago and TWRP and LineageOS to my LG G5 (H850) last year -- the S2 was easy, the G5 very tricky, but the G2 kills me. The G5 took a real effort because no guide worked for my phone, and I had to take a little from this guide, a little from that and add a bit of my own (let me know if anyone is interested in how I flashed LOS to my G5). I have tried the same with my G2 -- but I seem to have come to a dead end.
I am writing all that that to tell you that I have gone to great length before troubling you. Here is in summary what I have done so far and where I stand:
I have installed the sdk toolkit, adb and fastboot properly when I flashed my G5 last year.
Now I have started with the instructions from the LineageOS wiki (wiki.lineageos.org/devices/d802/install). I have activated USB debugging and rooted my phone using One Click root (Before One Click Root for the G2 was available, I could not even root my phone).
Then I flashed TWRP using "dd" as explained in the installation guide in the LineagOS wiki. I also tried it by flashing through the TWRP app (the app said it was flashed successfully). I tried TWRP 3.2.3.0 and 2.8.7.0 for the D802. The result always was as set out below.
After that I turned off my phone and started I by holding power + Volume down, releasing power briefly after the LG logo appeared. I went through factory reset (selected yes and yes), and here the problems begin (the same when I use “adb reboot recovery”). The phone should start into TWRP, but it does not. Instead the start screen with the LG logo appears, and in the upper left corner the following message appears:
ERROR: boot certification verify
[26480]------------------------------------- -
[26480]
[26520] Secure booting Error!
[26570] Cause: boot certification verify
[26620]
[26670]-------------------------------------- -
If the numbers in the square brackets make sense to you: They change every time I boot.
The next screen reads
------------------------------------------------- -
Critical Error!
------------------------------------------------- -
DemiGod Crash Handler : Critical Error!
Some information on how to reboot or access Download mode]
------------------------------------------------- -
Board Info Rev. : 1.1 speed.pvs : 1.3 serial : [...]
------------------------------------------------- -
I have tried many things, including several resets using LG FLash Tool 2014 to flash an entirely clean stock rom and starting fresh rooting and flashing. I also tried LG G2 D802 One Click Root Recovery V1.1, which even failed to root the phone.
My feeling is that the phone prevents me from properly installing TWRP. It does not allow me to boot into the bootloader using "adb reboot bootloader" (the command just restarts the phone). Therefore, I cannot put it into fastboot mode (I also tried the volume-up button method to put it into fastboot and failed), which may be crucial to properly install TWRP. In this regard, it may be relevant that the Developer Options show no option "OEM unlock"; that might be necessary to access the bootloader and fastboot mode…
What do you think? Do you have an idea how to solve the problem?
Thanks a lot and cheers!
So I've searched and searched and tried a lot of things before ending here..
I'm posting because I'm just straight outta my league at this point and think i may be a click away from a brick....
I was gifted a tab e that was sitting for 4 years .. and my tec skills here are not the best by far...but here goes .. i hope someone can help...
-----its been rooted and running a custom rom...
-----no root software was present ( king/ssu ect )
-----all attempts to reinstall above software and access root have failed
-----Twrp was installed .... i have a twrp recovery file ...
-----twrp was accessible at boot, however whatever i did last, now results in a black screen with the word "recovery" on it and four options below ( reboot, advanced restore and
one other)
------ I would like to restore Twrp and be able to use custom (updated) ROM's and have root control
------Twrp will not get past the dreaded "installer has stopped working" error msg when installed from my tab e....despite trying many "solutions"
------ i have odin 3.14.1 installed.. but am unable to side load or anything else.. (am aware of download mode ect )
------ debug mode and samsung usb drivers and all that have been done.
this is the info i see at boot :
oden mode
prod name: sm-T560nu
cus. bin. : custom
sys. stat: custom
faplock: off
war. void : 0x1(4)
qualicom secure boot: enable (cbs)
ap swaev: s1,t1,h1,a1,p1
sec. download : enable
this is my sys info:
droid ver: 6.0.1
kern. ver. : 3.10.49-9445949
[email protected] #1
wen dec 28 16:32:41 kst 2016
build # : mmb29m.t560nuues1bpl1
Se 4 droid stat : enforcing
sepf_secmobile_6.0.1_0030
sec. soft ver: asks v1.2_161011
knox ver : 2.6
droid sec patch level : oct 1 2016
much appreciation for any ideas..
Download TWRP from here: https://dl.twrp.me/gtelwifiue/ and download Linage from here: https://forum.xda-developers.com/ga...official-lineageos-17-1-galaxy-tab-e-t4150709.
Install TWRP from Odin. Then flash Linage/GAPPS/Magisk from TWRP and off you go.