hi guys,
I wantet to change from the ressurection remix rom (lp) to the stock rom via a kdz file.
now my phone got stucked in the window "fimeware update"
it says " do not unpulg the usb connection until the process is complete" and "0%"
long pressing the power button to reboot or removing the battery will not help. it will only boot the phone into the " fimeware update" window(the Download mode window is not shown) again.
lg flashtool doesn't recognize it. but when i plug it into my computer its shown in the device manager section as "lge android phone". so there is maybe hope for me.
thank you so much for the support!
sandrahum said:
hi guys,
I wantet to change from the ressurection remix rom (lp) to the stock rom via a kdz file.
now my phone got stucked in the window "fimeware update"
it says " do not unpulg the usb connection until the process is complete" and "0%"
long pressing the power button to reboot or removing the battery will not help. it will only boot the phone into the " fimeware update" window(the Download mode window is not shown) again.
lg flashtool doesn't recognize it. but when i plug it into my computer its shown in the device manager section as "lge android phone". so there is maybe hope for me.
thank you so much for the support!
Click to expand...
Click to collapse
did you set it up as port com41. read this post. its a tot method but it xplains how to set up to detect phone.
1. With phone NOT plugged into a USB Cable, Hold the Power button to turn off phone
2. Plug your USB cable into your computer
3. Hold the Volume UP Button on your Phone
4. While Still Holding the Volume UP button, plug in the USB cable to your Phone
5. Continue to hold the Volume UP button until your phone enters Download Mode
6. If this does not work, pull the USB cable and start from #1 of this section
Step #3: Change Com Port to 41
1. With your phone STILL in Download Mode and STILL Plugged into Computer
2. Go into Device Manager
---a. Press and hold your Windows Key (Between CTRL and ALT)
---b. Tap the ‘Pause/Break’ Key (Usually Top Right of Keyboard, might be different on yours)
---c. Click on ‘Device Manager’
3. In the Device List, scroll down to ‘Ports (COM & LPT) and double click to expand
4. Find the ‘LGE AndroidNet USB Serial Port (COM4)’ (Your COM Port Number might be different, that’s OK)
5. Double click to open the port
6. On the Tabs at the top of that screen, click on ‘Port Settings’
7. Click on ‘Advanced…’
8. Click on the Com Port number to drop down the list
9. Scroll down to ‘COM41’ and select it
10. Click ‘OK’ Button to save that
11. Click ‘OK’ Button to close the Com Port Properties
12. Close the Device Manager
13. Close the System Window
14. Go back to the Desktop
15. That’s it, You’ve Changed the Com Port to 41
thanks
raptorddd said:
did you set it up as port com41. read this post. its a tot method but it xplains how to set up to detect phone.
1. With phone NOT plugged into a USB Cable, Hold the Power button to turn off phone
2. Plug your USB cable into your computer
3. Hold the Volume UP Button on your Phone
4. While Still Holding the Volume UP button, plug in the USB cable to your Phone
5. Continue to hold the Volume UP button until your phone enters Download Mode
6. If this does not work, pull the USB cable and start from #1 of this section
Step #3: Change Com Port to 41
1. With your phone STILL in Download Mode and STILL Plugged into Computer
2. Go into Device Manager
---a. Press and hold your Windows Key (Between CTRL and ALT)
---b. Tap the ‘Pause/Break’ Key (Usually Top Right of Keyboard, might be different on yours)
---c. Click on ‘Device Manager’
3. In the Device List, scroll down to ‘Ports (COM & LPT) and double click to expand
4. Find the ‘LGE AndroidNet USB Serial Port (COM4)’ (Your COM Port Number might be different, that’s OK)
5. Double click to open the port
6. On the Tabs at the top of that screen, click on ‘Port Settings’
7. Click on ‘Advanced…’
8. Click on the Com Port number to drop down the list
9. Scroll down to ‘COM41’ and select it
10. Click ‘OK’ Button to save that
11. Click ‘OK’ Button to close the Com Port Properties
12. Close the Device Manager
13. Close the System Window
14. Go back to the Desktop
15. That’s it, You’ve Changed the Com Port to 41
Click to expand...
Click to collapse
thanks for the answer. i followed your instructions but that doesn´t changed the situation. the phone still shows the "fimeware update" window.
the "download mode" window as we know comes before the "fimeware update" window but now it doesnt come anymore.
do you know how i can get a new working rom on the phone now ? :/
sandrahum said:
thanks for the answer. i followed your instructions but that doesn´t changed the situation. the phone still shows the "fimeware update" window.
the "download mode" window as we know comes before the "fimeware update" window but now it doesnt come anymore.
do you know how i can get a new working rom on the phone now ? :/
Click to expand...
Click to collapse
not so sure what to do next. this are suggestions
To get download mode maybe you could try nuke download in srk tools..
raptorddd said:
not so sure what to do next. this are suggestions
To get download mode maybe you could try nuke download in srk tools..
Click to expand...
Click to collapse
doesn´t work eighter.
maybe this information helps: at the "fimeware update" window ther is a gray boy at the bottom and it says "USER B47" or another number.
sandrahum said:
doesn´t work eighter.
maybe this information helps: at the "fimeware update" window ther is a gray boy at the bottom and it says "USER B47" or another number.
Click to expand...
Click to collapse
never seen that letters.. post your problem here, am sure youll get help there.. and hopefully fix it. tell him everything that has happened and the screen error.. and once you fix post update so others could see fix.
http://forum.xda-developers.com/showthread.php?t=2432476
I Have a Similar situation, after a OTA update I get stuck on bootloop and into download mode, windows just detected the phone like "LG Modem #2"
It a LS980.
Related
I too, had issues at first. I fixed them by a few easy steps.. (well, not so easy to figure out at first.)
1) Uninstall your device drivers for your phone. You can do this in Windows 7 by plugging your device in and going to Control Panel > Hardware > Devices and uninstalling the SAMSUNG_android. Once this is done, unplug it and plug it back in. An attempt to install the drivers will be made and the ADB one will most likely fail. Double click the SAMSUNG_android to bring up the properties for this device. Click the 'Hardware' tab. Click the 'SAMSUNG Android Composite ADB Interface' and hit properties. Then Driver > 'Update Driver'. Then select 'Browse my computer for driver software'
2) Download the drivers here: mediafire.com/?t9koyznu5ryygyt and extract them somewhere. Point the driver installation wizard to these drivers with 'Browse'. Hit 'Next.
Congratulations, your drivers are installed! Have fun rooting your Vibrant. I recommend the one click rooter, although it is just a copy of the update.zip and reboot function.
I guess I'm confused. What do drivers have to do with booting into recovery?
Power off
Hold Down Vol +/- and power at the same time.
Walla you have Recovery
----------------------------------------------------------
If your talking about Download Mode
Install your drivers
Plug in USB to PC, but not phone
Turn off Phone
Hold Vol +/-
Plug in USB to phone
Hold +/- for a second
Release Vol
Walla you are in Download Mode
That wasn't exactly working for me and others. I couldn't get into that mode by holding the buttons. The method I listed above managed to get me into recovery via adb, however.
Double helix
here is the guide to unbrick your phone if you got it hard bricked (no fast boot mode)
Disclaimer: do this on your own risk. I am not responsible if you..blah blah blah well what worse you can do you have already bricked your phone so pull your pants together and try this
USE only XP 32 bit (win 7 32 bit may work) nothing else works...
this method is to revive the device via accessing the qcom soc in bare board mode so that you can upgrade the firmware on device
1) download the flash tools given in the forum
2) download drivers and image of firmware (16gb or 32 gb) depending on your phone version (1.8 gb rar)
3) install everything
4) plug your phone via usb cable
if device manager shows
"qulacom HS-USB qloader 9008" under com port your phone is hardbricked and ready to go
if it shows more than 1 device under com port (gionee NEMA /GIONEE digonostics)your device is soft bricked and needs to follow steps for soft bricked device do not follow this guide any further
else if nothing happens hold power button for a long time (so as to make sure your phone is switched off) and try plugging in your device
5) open GNQC_download.exe and select path to bp-image folder in frimware image
6) AP image path is automatically selected (parent folder of bp-image folder)
7) select name as WBW 8901 or GBW 8900A (depending upon english or chinese version of flash tool)
8) select mode as emergence mode (bp + ap)
9)while qloader 9008 device is showing in mini window click download
10) after successful download phone will reboot in storage mode
11) if antivirus prompts for permission allow it
12) let it continue to download the files onto your device
after completion you can click tools and select which img files to download (let it be default)
click ok to save and now you can upgrade the firmware...
FAQ
Q) gnqc download doesn't works gives error "application failed to start"
A) install VC++ 2005 redistributeble SP1 ATL security upgrade
Q) receive incorrect parameter error.
A) you are using Chinese flash tool so make sure your copy of windows supports Chinese change local settings in control panel
Q) error in gnqc bp_image file doesnt exist
A) again remove Chinese characters from name of image folder
Q) phone is not detected
A) let it sit and drain the battery in 1-2 days now plug via usb cable
Q) phone is detected as usb hid device instead of com port
A) facing same problem fond no solution till yet
dhirajranger said:
here is the guide to unbrick your phone if you got it hard bricked (no fast boot mode)
Disclaimer: do this on your own risk. I am not responsible if you..blah blah blah well what worse you can do you have already bricked your phone so pull your pants together and try this
USE only XP 32 bit (win 7 32 bit may work) nothing else works...
this method is to revive the device via accessing the qcom soc in bare board mode so that you can upgrade the firmware on device
1) download the flash tools given in the forum
2) download drivers and image of firmware (16gb or 32 gb) depending on your phone version (1.8 gb rar)
3) install everything
4) plug your phone via usb cable
if device manager shows
"qulacom HS-USB qloader 9008" under com port your phone is hardbricked and ready to go
if it shows more than 1 device under com port (gionee NEMA /GIONEE digonostics)your device is soft bricked and needs to follow steps for soft bricked device do not follow this guide any further
else if nothing happens hold power button for a long time (so as to make sure your phone is switched off) and try plugging in your device
5) open GNQC_download.exe and select path to bp-image folder in frimware image
6) AP image path is automatically selected (parent folder of bp-image folder)
7) select name as WBW 8901 or GBW 8900A (depending upon english or chinese version of flash tool)
8) select mode as emergence mode (bp + ap)
9)while qloader 9008 device is showing in mini window click download
10) after successful download phone will reboot in storage mode
11) if antivirus prompts for permission allow it
12) let it continue to download the files onto your device
after completion you can click tools and select which img files to download (let it be default)
click ok to save and now you can upgrade the firmware...
FAQ
Q) gnqc download doesn't works gives error "application failed to start"
A) install VC++ 2005 redistributeble SP1 ATL security upgrade
Q) receive incorrect parameter error.
A) you are using Chinese flash tool so make sure your copy of windows supports Chinese change local settings in control panel
Q) error in gnqc bp_image file doesnt exist
A) again remove Chinese characters from name of image folder
Q) phone is not detected
A) let it sit and drain the battery in 1-2 days now plug via usb cable
Q) phone is detected as usb hid device instead of com port
A) facing same problem fond no solution till yet
Click to expand...
Click to collapse
I can't see com port? What to do?
kieudaigia said:
I can't see com port? What to do?
Click to expand...
Click to collapse
can you boot into fastboot (red gionee logo)
try power + vol down when phone is off
try vol up + vol down and plug usb when phone is switched off
dhirajranger said:
can you boot into fastboot (red gionee logo)
try power + vol down when phone is off
try vol up + vol down and plug usb when phone is switched off
Click to expand...
Click to collapse
I follow the instructions, but still no appearance com port
Try power + vol up khi phone is off, then on "android system recovery (3e)
kieudaigia said:
I follow the instructions, but still no appearance com port
Try power + vol up khi phone is off, then on "android system recovery (3e)
Click to expand...
Click to collapse
if you can access recovery it means your phone is not hard bricked....
also did you installed all drivers on your xp machine?
dhirajranger said:
here is the guide to unbrick your phone if you got it hard bricked (no fast boot mode)
Disclaimer: do this on your own risk. I am not responsible if you..blah blah blah well what worse you can do you have already bricked your phone so pull your pants together and try this
USE only XP 32 bit (win 7 32 bit may work) nothing else works...
this method is to revive the device via accessing the qcom soc in bare board mode so that you can upgrade the firmware on device
1) download the flash tools given in the forum
2) download drivers and image of firmware (16gb or 32 gb) depending on your phone version (1.8 gb rar)
3) install everything
4) plug your phone via usb cable
if device manager shows
"qulacom HS-USB qloader 9008" under com port your phone is hardbricked and ready to go
if it shows more than 1 device under com port (gionee NEMA /GIONEE digonostics)your device is soft bricked and needs to follow steps for soft bricked device do not follow this guide any further
else if nothing happens hold power button for a long time (so as to make sure your phone is switched off) and try plugging in your device
5) open GNQC_download.exe and select path to bp-image folder in frimware image
6) AP image path is automatically selected (parent folder of bp-image folder)
7) select name as WBW 8901 or GBW 8900A (depending upon english or chinese version of flash tool)
8) select mode as emergence mode (bp + ap)
9)while qloader 9008 device is showing in mini window click download
10) after successful download phone will reboot in storage mode
11) if antivirus prompts for permission allow it
12) let it continue to download the files onto your device
after completion you can click tools and select which img files to download (let it be default)
click ok to save and now you can upgrade the firmware...
FAQ
Q) gnqc download doesn't works gives error "application failed to start"
A) install VC++ 2005 redistributeble SP1 ATL security upgrade
Q) receive incorrect parameter error.
A) you are using Chinese flash tool so make sure your copy of windows supports Chinese change local settings in control panel
Q) error in gnqc bp_image file doesnt exist
A) again remove Chinese characters from name of image folder
Q) phone is not detected
A) let it sit and drain the battery in 1-2 days now plug via usb cable
Q) phone is detected as usb hid device instead of com port
A) facing same problem fond no solution till yet
Click to expand...
Click to collapse
if its soft brick.. how to solve... help me plz
hooney_zam said:
if its soft brick.. how to solve... help me plz
Click to expand...
Click to collapse
if you can get into fastboot just install twrp/cwm
and install stock rom back
Please Help!!
dhirajranger said:
here is the guide to unbrick your phone if you got it hard bricked (no fast boot mode)
Disclaimer: do this on your own risk. I am not responsible if you..blah blah blah well what worse you can do you have already bricked your phone so pull your pants together and try this
USE only XP 32 bit (win 7 32 bit may work) nothing else works...
this method is to revive the device via accessing the qcom soc in bare board mode so that you can upgrade the firmware on device
1) download the flash tools given in the forum
2) download drivers and image of firmware (16gb or 32 gb) depending on your phone version (1.8 gb rar)
3) install everything
4) plug your phone via usb cable
if device manager shows
"qulacom HS-USB qloader 9008" under com port your phone is hardbricked and ready to go
if it shows more than 1 device under com port (gionee NEMA /GIONEE digonostics)your device is soft bricked and needs to follow steps for soft bricked device do not follow this guide any further
else if nothing happens hold power button for a long time (so as to make sure your phone is switched off) and try plugging in your device
5) open GNQC_download.exe and select path to bp-image folder in frimware image
6) AP image path is automatically selected (parent folder of bp-image folder)
7) select name as WBW 8901 or GBW 8900A (depending upon english or chinese version of flash tool)
8) select mode as emergence mode (bp + ap)
9)while qloader 9008 device is showing in mini window click download
10) after successful download phone will reboot in storage mode
11) if antivirus prompts for permission allow it
12) let it continue to download the files onto your device
after completion you can click tools and select which img files to download (let it be default)
click ok to save and now you can upgrade the firmware...
FAQ
Q) gnqc download doesn't works gives error "application failed to start"
A) install VC++ 2005 redistributeble SP1 ATL security upgrade
Q) receive incorrect parameter error.
A) you are using Chinese flash tool so make sure your copy of windows supports Chinese change local settings in control panel
Q) error in gnqc bp_image file doesnt exist
A) again remove Chinese characters from name of image folder
Q) phone is not detected
A) let it sit and drain the battery in 1-2 days now plug via usb cable
Q) phone is detected as usb hid device instead of com port
A) facing same problem fond no solution till yet
Click to expand...
Click to collapse
Okay finally i have been able to get everything ready as in both drivers and firmware file. but now the issue is my phone is now detecting as a USB HID DEVICE instead of com port. and from your post, u said that is a problem u were also facing. i will like to ask if you have a fix or solution to that problem. because i am facing this same issue and now it seems i can't fix my phone.:crying::crying::crying::crying::crying:
Please Help!!
steps parku said:
okay finally i have been able to get everything ready as in both drivers and firmware file. But now the issue is my phone is now detecting as a usb hid device instead of com port. And from your post, u said that is a problem u were also facing. I will like to ask if you have a fix or solution to that problem. Because i am facing this same issue and now it seems i can't fix my phone.:crying::crying::crying::crying::crying:
Please help!!
Click to expand...
Click to collapse
where i can get firmware file ?
Firmware + Flash ware, all of Gione
andresplata94 said:
where i can get firmware file ?
Click to expand...
Click to collapse
Download the firmware file from the link below, u can use google translate to get the interpretation of the website. Make sure u download the files meant for Gionee elife E7, if that is really ur device. however i am still stuck at my device showing as HID Device and i will be deeply grateful if anyone here has a fix to this issue.
wwwdotelifedotcom/thread-22957-1-7dothtml[/url]
i can't post links here, so pleae, copy and paste this into your browser, and replace the 'dot' with '.'
Steps Parku said:
Download the firmware file from the link below, u can use google translate to get the interpretation of the website. Make sure u download the files meant for Gionee elife E7, if that is really ur device. however i am still stuck at my device showing as HID Device and i will be deeply grateful if anyone here has a fix to this issue.
wwwdotelifedotcom/thread-22957-1-7dothtml[/url]
i can't post links here, so pleae, copy and paste this into your browser, and replace the 'dot' with '.'
Click to expand...
Click to collapse
nice i get files now, but anyway this toturial doesnt work for me, what happends next ? :/
help me
Sofbrick ?
dhirajranger said:
here is the guide to unbrick your phone if you got it hard bricked (no fast boot mode)
Disclaimer: do this on your own risk. I am not responsible if you..blah blah blah well what worse you can do you have already bricked your phone so pull your pants together and try this
USE only XP 32 bit (win 7 32 bit may work) nothing else works...
this method is to revive the device via accessing the qcom soc in bare board mode so that you can upgrade the firmware on device
1) download the flash tools given in the forum
2) download drivers and image of firmware (16gb or 32 gb) depending on your phone version (1.8 gb rar)
3) install everything
4) plug your phone via usb cable
if device manager shows
"qulacom HS-USB qloader 9008" under com port your phone is hardbricked and ready to go
if it shows more than 1 device under com port (gionee NEMA /GIONEE digonostics)your device is soft bricked and needs to follow steps for soft bricked device do not follow this guide any further
else if nothing happens hold power button for a long time (so as to make sure your phone is switched off) and try plugging in your device
5) open GNQC_download.exe and select path to bp-image folder in frimware image
6) AP image path is automatically selected (parent folder of bp-image folder)
7) select name as WBW 8901 or GBW 8900A (depending upon english or chinese version of flash tool)
8) select mode as emergence mode (bp + ap)
9)while qloader 9008 device is showing in mini window click download
10) after successful download phone will reboot in storage mode
11) if antivirus prompts for permission allow it
12) let it continue to download the files onto your device
after completion you can click tools and select which img files to download (let it be default)
click ok to save and now you can upgrade the firmware...
FAQ
Q) gnqc download doesn't works gives error "application failed to start"
A) install VC++ 2005 redistributeble SP1 ATL security upgrade
Q) receive incorrect parameter error.
A) you are using Chinese flash tool so make sure your copy of windows supports Chinese change local settings in control panel
Q) error in gnqc bp_image file doesnt exist
A) again remove Chinese characters from name of image folder
Q) phone is not detected
A) let it sit and drain the battery in 1-2 days now plug via usb cable
Q) phone is detected as usb hid device instead of com port
A) facing same problem fond no solution till yet
Click to expand...
Click to collapse
Hey man, how are u ?
i have a serius problem with my device " blu life pure xl" i installed norios room on my device and now is bricked
i try install back my old room froom recovery and nothing happend
too i try restore a backup ( i have a this backup some time ago) and again nothing happends
i dont know what happend, but always when i turn on my device show gionne smarthphone logo and it is bootloop
u can help me ?
i dont know how solve it ?
thank you !!!!
---------- Post added at 04:54 AM ---------- Previous post was at 04:10 AM ----------
dhirajranger said:
if you can get into fastboot just install twrp/cwm
and install stock rom back
Click to expand...
Click to collapse
even installed room back i cant solve this soft brick, what now ? :c
---------- Post added at 05:01 AM ---------- Previous post was at 04:54 AM ----------
when i did click on dowload button its show "open com port fail, please check if other program are using the COM por[QDloader] ! ! ! "
what mean it, how i can solve it ?
my phone is stuck in the white gionee logo.
dhirajranger said:
if you can get into fastboot just install twrp/cwm
and install stock rom back
Click to expand...
Click to collapse
hi plz help my phone is stuck in the white gionee logo wont boot after that.its not even detecting in the system could you please tell me a step by step procedure on how to install cwm or any other recovery and flash the stock rom...
plz help needed.
dhirajranger said:
here is the guide to unbrick your phone if you got it hard bricked (no fast boot mode)
Disclaimer: do this on your own risk. I am not responsible if you..blah blah blah well what worse you can do you have already bricked your phone so pull your pants together and try this
USE only XP 32 bit (win 7 32 bit may work) nothing else works...
this method is to revive the device via accessing the qcom soc in bare board mode so that you can upgrade the firmware on device
1) download the flash tools given in the forum
2) download drivers and image of firmware (16gb or 32 gb) depending on your phone version (1.8 gb rar)
3) install everything
4) plug your phone via usb cable
if device manager shows
"qulacom HS-USB qloader 9008" under com port your phone is hardbricked and ready to go
if it shows more than 1 device under com port (gionee NEMA /GIONEE digonostics)your device is soft bricked and needs to follow steps for soft bricked device do not follow this guide any further
else if nothing happens hold power button for a long time (so as to make sure your phone is switched off) and try plugging in your device
5) open GNQC_download.exe and select path to bp-image folder in frimware image
6) AP image path is automatically selected (parent folder of bp-image folder)
7) select name as WBW 8901 or GBW 8900A (depending upon english or chinese version of flash tool)
8) select mode as emergence mode (bp + ap)
9)while qloader 9008 device is showing in mini window click download
10) after successful download phone will reboot in storage mode
11) if antivirus prompts for permission allow it
12) let it continue to download the files onto your device
after completion you can click tools and select which img files to download (let it be default)
click ok to save and now you can upgrade the firmware...
FAQ
Q) gnqc download doesn't works gives error "application failed to start"
A) install VC++ 2005 redistributeble SP1 ATL security upgrade
Q) receive incorrect parameter error.
A) you are using Chinese flash tool so make sure your copy of windows supports Chinese change local settings in control panel
Q) error in gnqc bp_image file doesnt exist
A) again remove Chinese characters from name of image folder
Q) phone is not detected
A) let it sit and drain the battery in 1-2 days now plug via usb cable
Q) phone is detected as usb hid device instead of com port
A) facing same problem fond no solution till yet
Click to expand...
Click to collapse
Help me, error "Enter EDL mode fail, please press power on( or power off) to update port and try again" How do i do?
kieudaigia said:
Help me, error "Enter EDL mode fail, please press power on( or power off) to update port and try again" How do i do?
Click to expand...
Click to collapse
Facing same problem
EDL MODE FAIL
What to do
Guys Please Help
shivam2702 said:
Click to expand...
Click to collapse
When you connect the phone to the PC, does it loader any driver? Use Device Manager to check...
If it loads the QLoader driver, use the "Emergency Mode" in GNQC 1.6.9.0.
If no driver loads, disconnect the phone and press the power button for 30 secs and try again.
If this also fails, wait a day for the device discharge, press the power button for 30 secs and try again...
Let me know how it went...
RSGI_PT said:
When you connect the phone to the PC, does it loader any driver? Use Device Manager to check...
If it loads the QLoader driver, use the "Emergency Mode" in GNQC 1.6.9.0.
If no driver loads, disconnect the phone and press the power button for 30 secs and try again.
If this also fails, wait a day for the device discharge, press the power button for 30 secs and try again...
Let me know how it went...
Click to expand...
Click to collapse
This Is my error looks like
RSGI_PT said:
When you connect the phone to the PC, does it loader any driver? Use Device Manager to check...
If it loads the QLoader driver, use the "Emergency Mode" in GNQC 1.6.9.0.
If no driver loads, disconnect the phone and press the power button for 30 secs and try again.
If this also fails, wait a day for the device discharge, press the power button for 30 secs and try again...
Let me know how it went...
Click to expand...
Click to collapse
Help Buddy Please Reply
shivam2702 said:
This Is my error looks like
Click to expand...
Click to collapse
Try to flash again.
If that messege apears again just press the power button of the phone for a few secs without disconnecting from the PC.
The download should begin. If not change the Mode to Normal and press the power button for a few secs.
Dont disconnect the phone from the PC, cause that messege apears because the GNQC is unable to confirm the state of the phone. By pressing the power button you are refreshing the connecting and the GNQC should detect the state of the phone.
Also you can try this using another USB port on your PC.
Feed back me
MSM8994DownloadTool.exe Won't Work For Me
I need help.
My phone is stuck on the fastboot screen, meaning I can only Power if off and into Fastboot (using the Vol+ and Power buttons). Other than that, it does nothing. I cannot get into the OS at all, which means I can't enable USB debugging or anything. Fastboot recognizes my device, which is a OnePlus Two), but ADB won't, nor will my Windows 7 PC as a USB device. With that in mind, I followed all the steps in the posted guide. I get all the way to running the "MSM8994DownloadTool.exe" and nothing happens. Its as if the Recovery Tool doesn't even see my device. So, I'm really stuck and don't know what to do.
For clarity, here's exactly what I did (see below). I get all the way to Section B, Step 2 and that's where it breaks down. There's no different line, and no process ever runs, even after waiting 30 minutes. I ran the tool as Administrator, but still no luck. Can anyone help me? Just as additional info, my Mac also does not recognize my OPT as a USB device. Also, I tried my backup USB-C cable from the OEM, with the same results.
A. Install the Certificates followed by the Qualcomm drivers.
1. Restart your computer with Driver Signature Enforcement Disabled (Advanced Startup) Let me Google it For You
2. Open the folder "qc" and install the Test Certificate in the following Stores: Trusted Root, Trusted Publisher, Third-Party Root and Personal
3. Run the Qualcomm setup wizard (also located in the qc folder)
4. When completed, restart your PC again with Driver Signature Enforcement Disabled (Advanced Startup)
5. Turn off your phone and disconnect the USB cable from the phone.
6. Hold vol-up and plug in the USB(Do not press Power button). The screen will stay black but you will hear a sound from windows that a device is attached.
7. The driver should now automatically install. If not, go to device manager and right click "Unknown Device" and click "Update Driver" Search up the QC folder and press ok. The driver should now install. (Got the RELINK issue? Take a look here: http://forum.xda-developers.com/show...1&postcount=46)
B. Flashing Process
1. Open the OnePlus2_14_A.11_151211 folder and open "MSM8994DownloadTool.exe"
2. Look if your phone is detected in the list. everything is Chinese but you will see one row with different chinese text from the rest within the list. If not, recheck if driver is detected in Device Manager (If not, go back to Step A - Line 4).
I think you have a bad download, try downloading it again and download the 3.0.2 version if you can.
Phil01234 said:
MSM8994DownloadTool.exe Won't Work For Me
I need help.
My phone is stuck on the fastboot screen, meaning I can only Power if off and into Fastboot (using the Vol+ and Power buttons). Other than that, it does nothing. I cannot get into the OS at all, which means I can't enable USB debugging or anything. Fastboot recognizes my device, which is a OnePlus Two), but ADB won't, nor will my Windows 7 PC as a USB device. With that in mind, I followed all the steps in the posted guide. I get all the way to running the "MSM8994DownloadTool.exe" and nothing happens. Its as if the Recovery Tool doesn't even see my device. So, I'm really stuck and don't know what to do.
For clarity, here's exactly what I did (see below). I get all the way to Section B, Step 2 and that's where it breaks down. There's no different line, and no process ever runs, even after waiting 30 minutes. I ran the tool as Administrator, but still no luck. Can anyone help me? Just as additional info, my Mac also does not recognize my OPT as a USB device. Also, I tried my backup USB-C cable from the OEM, with the same results.
A. Install the Certificates followed by the Qualcomm drivers.
1. Restart your computer with Driver Signature Enforcement Disabled (Advanced Startup) Let me Google it For You
2. Open the folder "qc" and install the Test Certificate in the following Stores: Trusted Root, Trusted Publisher, Third-Party Root and Personal
3. Run the Qualcomm setup wizard (also located in the qc folder)
4. When completed, restart your PC again with Driver Signature Enforcement Disabled (Advanced Startup)
5. Turn off your phone and disconnect the USB cable from the phone.
6. Hold vol-up and plug in the USB(Do not press Power button). The screen will stay black but you will hear a sound from windows that a device is attached.
7. The driver should now automatically install. If not, go to device manager and right click "Unknown Device" and click "Update Driver" Search up the QC folder and press ok. The driver should now install. (Got the RELINK issue? Take a look here: http://forum.xda-developers.com/show...1&postcount=46)
B. Flashing Process
1. Open the OnePlus2_14_A.11_151211 folder and open "MSM8994DownloadTool.exe"
2. Look if your phone is detected in the list. everything is Chinese but you will see one row with different chinese text from the rest within the list. If not, recheck if driver is detected in Device Manager (If not, go back to Step A - Line 4).
Click to expand...
Click to collapse
I've bricked my op2 a while ago. I'm a real noob so I don't know if it will work but have you installed the adb mac drivers or try "fastboot continue" while in fastboot. Just don't give up and keep try. You have absolutely nothing to lose.
chintu1234 said:
I think you have a bad download, try downloading it again and download the 3.0.2 version if you can.
Click to expand...
Click to collapse
Thank you very much. I have the latest version, but still nothing. I don't know if this has anything to do with it, but my OPT wasn't being recognized as a USB device even before I screwed up. That leads me to believe my OPT USB is maybe not functional. ADB doesn't recognize it at, nor will the MP...DownloadTool.exe. I'm guessing it is just hard-bricked since I have no other way (besides USB) to interface with the device.
Phil01234 said:
Thank you very much. I have the latest version, but still nothing. I don't know if this has anything to do with it, but my OPT wasn't being recognized as a USB device even before I screwed up. That leads me to believe my OPT USB is maybe not functional. ADB doesn't recognize it at, nor will the MP...DownloadTool.exe. I'm guessing it is just hard-bricked since I have no other way (besides USB) to interface with the device.
Click to expand...
Click to collapse
Try connecting your OPT to some other guys pc and see, it may be because of your pc's end that its not getting connected.
And if the same thing happens with a different pc then yeah your usb port or something is fried. Try going to service center if the same thing happens again.
This Procedure Can Also Be Used To Flash Stock Rom And To Regain Warranty
Scenarios-
1.You Somehow relocked your bootloader while on custom rom
2.Your phone flashes the zuk logo and then screen goes blank with led blinking and you cant see the options to go to fastboot or other modes
3.Your Phone Shows port 9008 or 900e while connected to PC
3.You want to regain your warranty
4.You just want to go back to stock rom
This Guide Is for All of the Above Sceneriaos
Following this guide will revert your phone back to stock ROM nougat while deleting your user data and relocking your bootloader
WARNING
If your device is already bricked and if it goes worse than I am not responsible for it. Do at your own risk.
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
B)QPST ROM
1.Indian Version Nougat http://www.mediafire.com/file/f86cs...SER_Q01080.2_N_ZUI_2.5.104_ST_170418_QPST.zip
2.Chinese Version Nougat
http://s.bs.zui.com/DGDc
Extract these rom to preferably a new folder in the root of c drive
STEPS
INSTALL ALL TOOLS AND DRIVERS GIVEN ABOVE
A)If phone is running fine
1.Enable USB Debugging on your Device and give permission to any prompts
2.Open Minimal ADB and Fastboot and put the following command
adb reboot edl
OR
Put the phone in fastboot mode, Open Minimal ADB and Fastboot and put the following command
fastboot reboot edl
3.Close Window
4.Open Mi Flash Tool
5.Click "select" button on the upper left and browse to the directory where you extracted your stock rom and click refresh on the right COM port shall appear below
6.Click Flash
7.DONT REMOVE OR DISCONNECT THE USB CABLE FLASHING WILL TAKE SOME TIME
8.After success is shown press the power button for sometime until the phone vibrates first boot will take some time
9.Tada! You are back to stock rom along with your WARRANTY!(If Mi flash doesnt work use QFIL as per given in the steps 1 to 4 given below)
B)If phone doesnt bootup
1. Restart your PC and open QFILClick
2. Select "Flat Build" and "Browse". Now navigate to the extracted ROM/Firmware, and select prog_emmc_firehose_8996_ddr.elf.
3.Select the "load xml" button. This will appear a new explorer. One of them will be needed to navigate to the file
rawprogram0.xml the second one will ask for patch0.xml
4.Turn your phone off. Now press and hold the volume + button, while pressing the power button for 0.5 seconds and plug in the
USB cable in the same moment. If it was successful your phone should appear at QPST/QFIL and you are able to press the
download button. Press the download process and wait to finish.
If it fails, In QFIL Change
"Device Type" to eMMC
"Validation Mode" to 0-No validation
"Reset after Download" no needed to tick (optional)
5.If your phone is not detected in the QFIL or it shows up as port 900E then there are 2 ways to get to 9008 mode
I)
a.Unplug your phone from the computer.
b. Press and hold the POWER button until your phone restarting 3-5 times.
c. After the 3rd times (or more), you will see the notification LED goes off in the middle of boot process, and at that time, quick
press VOLUME + button and release the POWER button but keep the VOLUME + button pressed.
d. Your phone will be at POWER OFF status.
e. After your phone is completely off, press and hold the VOLUME +, then press POWER button and connect your USB at the
same time.
f. Your computer will showing a notification about a new port.
g. If you succeed, you will see Diagnostic Port 9008 at QFIL software
II)
Right click on my computer and select MANAGE, then select Device Manager
See if your device is connected as Diagnostic Port 900E
If it is shown as “QHSUSB_BULK” under Other Device
a. Right-click on QHSUSB_BULK and choose “Update Driver Software“
b. Now click on the Browse button and locate the extracted Qualcomm QDLoader drivers.
c. The installation process shall take place immediately and a system notification will appear. Just choose “Install this driver software anyway“.
d.Click the Close button and check back at Device Manager window. You will now see “Qualcomm HS-USB QDLoader 9008 (COM10)” under Ports (COM & LPT) section.
6. Flash your phone using QFIL software once phone connects in 9008 mode and then reboot.
(Alternatively you can also use the Mi Flash Tool once the phone is in 9008 port)
7.Tada! You have successfully unbricked your phone and regained your WARRANTY!
Update: For saving your user data if your phone gets bricked by bootloader getting locked ONLY follow the below guide
How To-
1. How to switch it off
-firstly this is happening because you have locked you're bootloader
- You have black screen and led on so just hold power button then Zuk logo will be flash after that you will get black screen again and again the phone was preparing to reboot but before that the led will get turn off immediately release power button
- You have it Your phone is switched off
(Let it reboot once after that don't leave the power button and after that led will get off for small time this is the time you have to remove finger from power button this is tricky )
2. Going to Bootloader
-Firstly connect the USB to laptop
-after you have switched off your phone press volume up and down together and with holding buttons connect the phone to USB and you will see the fastboot mode
3. Unlock your phone
-Remember the unlock bootloader file in your email re download it and unlock your bootloader again(no need to redownload if you already have it the file is permanent)
- after unlocking phone you will see phone rebooted press power button reboot press volume the volume button and go to reboot option
- go to fastboot and flash the TWRP and you will see that your data on internal storage is present so flash any ROM and you will see your data
Update: Deep flash using Deep Flash Cable And Procedure to make a deep flash cable
Cut the outer rubber and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
After flashing carefully cover the cut portion by putting the rubber casing first and then covering with electrical tape.
So be careful not to tear anything you just need to precisely cut the covering (around 0.5 cm) in the shape of a ring
Happy Flashing!
I think someone has made this guide already.
I see.
well i have a similar issue that i am stuck at 9008 port that is edl but, i can flash rom via Qfil and Mi Flash toll but i cant boot onto it=
I cant get out of edl mode lol. stuck at it.
I deleted some files from qpst rom for intentionally hard bricking my phone and heres another fix.
Cut the outer plastic and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
Happy Flashing!
AstroBiswas said:
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994 - not last edition, latest is v1.0.8
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270 - not last edition, latest is 2.7.460 (fix "sahara" error)
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download - not needed
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790 - not needed (if you use the previous paragraph).
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
Click to expand...
Click to collapse
@AstroBiswas Read red comment.
Not_James_Bond said:
I think someone has made this guide already.
Click to expand...
Click to collapse
Of course!
https://forum.xda-developers.com/le...-to-recover-hard-bricked-zuk-z2-plus-t3576007
Not even coming up as 900E
AstroBiswas said:
This Procedure Can Also Be Used To Flash Stock Rom And To Regain Warranty
Scenarios-
1.You Somehow relocked your bootloader while on custom rom
2.Your phone flashes the zuk logo and then screen goes blank with led blinking and you cant see the options to go to fastboot or other modes
3.Your Phone Shows port 9008 or 900e while connected to PC
3.You want to regain your warranty
4.You just want to go back to stock rom
This Guide Is for All of the Above Sceneriaos
Following this guide will revert your phone back to stock ROM nougat while deleting your user data and relocking your bootloader
WARNING
If your device is already bricked and if it goes worse than I am not responsible for it. Do at your own risk.
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
B)QPST ROM
1.Indian Version Nougat http://www.mediafire.com/file/f86cs...SER_Q01080.2_N_ZUI_2.5.104_ST_170418_QPST.zip
2.Chinese Version Nougat
http://s.bs.zui.com/DGDc
Extract these rom to preferably a new folder in the root of c drive
STEPS
INSTALL ALL TOOLS AND DRIVERS GIVEN ABOVE
A)If phone is running fine
1.Enable USB Debugging on your Device and give permission to any prompts
2.Open Minimal ADB and Fastboot and put the following command
adb reboot edl
OR
Put the phone in fastboot mode, Open Minimal ADB and Fastboot and put the following command
fastboot reboot edl
3.Close Window
4.Open Mi Flash Tool
5.Click "select" button on the upper left and browse to the directory where you extracted your stock rom and click refresh on the right COM port shall appear below
6.Click Flash
7.DONT REMOVE OR DISCONNECT THE USB CABLE FLASHING WILL TAKE SOME TIME
8.After success is shown press the power button for sometime until the phone vibrates first boot will take some time
9.Tada! You are back to stock rom along with your WARRANTY!(If Mi flash doesnt work use QFIL as per given in the steps 1 to 4 given below)
B)If phone doesnt bootup
1. Restart your PC and open QFILClick
2. Select "Flat Build" and "Browse". Now navigate to the extracted ROM/Firmware, and select prog_emmc_firehose_8996_ddr.elf.
3.Select the "load xml" button. This will appear a new explorer. One of them will be needed to navigate to the file
rawprogram0.xml the second one will ask for patch0.xml
4.Turn your phone off. Now press and hold the volume + button, while pressing the power button for 0.5 seconds and plug in the
USB cable in the same moment. If it was successful your phone should appear at QPST/QFIL and you are able to press the
download button. Press the download process and wait to finish.
If it fails, In QFIL Change
"Device Type" to eMMC
"Validation Mode" to 0-No validation
"Reset after Download" no needed to tick (optional)
5.If your phone is not detected in the QFIL or it shows up as port 900E then there are 2 ways to get to 9008 mode
I)
a.Unplug your phone from the computer.
b. Press and hold the POWER button until your phone restarting 3-5 times.
c. After the 3rd times (or more), you will see the notification LED goes off in the middle of boot process, and at that time, quick
press VOLUME + button and release the POWER button but keep the VOLUME + button pressed.
d. Your phone will be at POWER OFF status.
e. After your phone is completely off, press and hold the VOLUME +, then press POWER button and connect your USB at the
same time.
f. Your computer will showing a notification about a new port.
g. If you succeed, you will see Diagnostic Port 9008 at QFIL software
II)
Right click on my computer and select MANAGE, then select Device Manager
See if your device is connected as Diagnostic Port 900E
If it is shown as “QHSUSB_BULK” under Other Device
a. Right-click on QHSUSB_BULK and choose “Update Driver Software“
b. Now click on the Browse button and locate the extracted Qualcomm QDLoader drivers.
c. The installation process shall take place immediately and a system notification will appear. Just choose “Install this driver software anyway“.
d.Click the Close button and check back at Device Manager window. You will now see “Qualcomm HS-USB QDLoader 9008 (COM10)” under Ports (COM & LPT) section.
6. Flash your phone using QFIL software once phone connects in 9008 mode and then reboot.
(Alternatively you can also use the Mi Flash Tool once the phone is in 9008 port)
7.Tada! You have successfully unbricked your phone and regained your WARRANTY!
Update: For saving your user data if your phone gets bricked by bootloader getting locked ONLY follow the below guide
How To-
1. How to switch it off
-firstly this is happening because you have locked you're bootloader
- You have black screen and led on so just hold power button then Zuk logo will be flash after that you will get black screen again and again the phone was preparing to reboot but before that the led will get turn off immediately release power button
- You have it Your phone is switched off
(Let it reboot once after that don't leave the power button and after that led will get off for small time this is the time you have to remove finger from power button this is tricky )
2. Going to Bootloader
-Firstly connect the USB to laptop
-after you have switched off your phone press volume up and down together and with holding buttons connect the phone to USB and you will see the fastboot mode
3. Unlock your phone
-Remember the unlock bootloader file in your email re download it and unlock your bootloader again(no need to redownload if you already have it the file is permanent)
- after unlocking phone you will see phone rebooted press power button reboot press volume the volume button and go to reboot option
- go to fastboot and flash the TWRP and you will see that your data on internal storage is present so flash any ROM and you will see your data
Update: Deep flash using Deep Flash Cable And Procedure to make a deep flash cable
Cut the outer rubber and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
After flashing carefully cover the cut portion by putting the rubber casing first and then covering with electrical tape.
So be careful not to tear anything you just need to precisely cut the covering (around 0.5 cm) in the shape of a ring
Happy Flashing!
Click to expand...
Click to collapse
My hard brick z2 is not even coming up as 900E. Basically computer doesn't detect and no changes in device manager either. Please confirm what to do.
I have tried pressing buttons told by many others and in various other forums. It doesn't work. Does deep flash cable method work even if the phone is not detecting in 900E mode?
You have to boot in proper edl mode...for edl mode hold volume up button 15 second and immediately click power button for .5 sec and attach data cable to phone which is connected to pc and & immediately prees again power button. all while procees alway hold volume up button....
Zuk Z2 Pro Stuck in EDL HS-USB 9008 Port and automatically connecting and disconnect
Hi,
My Zuk Z2 Pro is stuck in EDL 9008 Port. Phone is totally bricked and no sound, no light, no vibration. When i connect with the computer, phone is connecting on HS USB 9008 port and get disconnected after 20-22 seconds and again automatically connected with in half second time.
I am facing this issue after flashing a ZUI 1.9 by using a QPAST/QFIL application. I think i have made stupid mistake by flashing a phone with "ERASE ALL BEFORE DOWNLOAD" option.
I have tried every scenario to get stable this 9008 port but no luck. Since last 5 days i am studying forums and applying every kind of solution but same result.
I am writing this post with high expectations and hope someone will take notice and help me to get rid of this problem.
I can pay through paypal if someone wants to provide professional services to resolve this matter
I will appreciate if someone have any idea and can help me. Thanks
Can someine please help me with this weird situation? Device got disconnected while flashing via qfil. Now no zuk logo nothing. Phone vibrates every 30 sec that's it. Wont even gets recognized by my laptop(no 9008 or 900e port!)
SilenT__ShadoW said:
Can someine please help me with this weird situation? Device got disconnected while flashing via qfil. Now no zuk logo nothing. Phone vibrates every 30 sec that's it. Wont even gets recognized by my laptop(no 9008 or 900e port!)
Click to expand...
Click to collapse
You need to use the deep flash guide which involved cutting and sorting the cable , procedure given in last part of OP
AstroBiswas said:
You need to use the deep flash guide which involved cutting and sorting the cable , procedure given in last part of OP
Click to expand...
Click to collapse
I've tired that also. Connecting phone to pc while green and black wires attached together and detaching them after 5 sec. That also did nothing. However i connect my phone to my pc it just vibrates and blinks led every 30 sec till i remove battery!
SilenT__ShadoW said:
I've tired that also. Connecting phone to pc while green and black wires attached together and detaching them after 5 sec. That also did nothing. However i connect my phone to my pc it just vibrates and blinks led every 30 sec till i remove battery!
Click to expand...
Click to collapse
You need to completely poweoff the phone (difficult in hard brick actually) before this procedure i have forgotten the way to do it, was given on zuk.eu i think, dont worry it may take time but these days hard bricks is repairable too.
AstroBiswas said:
You need to completely poweoff the phone (difficult in hard brick actually) before this procedure i have forgotten the way to do it, was given on zuk.eu i think, dont worry it may take time but these days hard bricks is repairable too.
Click to expand...
Click to collapse
Isn't removing battery connection means powering off the device???
SilenT__ShadoW said:
Isn't removing battery connection means powering off the device???
Click to expand...
Click to collapse
Yes!
AstroBiswas said:
Yes!
Click to expand...
Click to collapse
I'm doing the same.... Removing battery connection every time to switch off.
SilenT__ShadoW said:
I'm doing the same.... Removing battery connection every time to switch off.
Click to expand...
Click to collapse
Thats strange keep trying, perfect timing matters
AstroBiswas said:
Thats strange keep trying, perfect timing matters
Click to expand...
Click to collapse
What do you mean by perfect timing?!?
Never mind. Got my laptop to recognise it and flashed successfully.
Don't know what made it to change its mind!?
What happened?
- was trying to flash and cable got disconnected by accident.
- my phone started to vibrate and blink at the same time for every 30 sec(no zuk logo nothing) and can't seems to be stopped.
- laptop doesn't seems to recognise when device gets connected (no 900e or 9008 port shows up at device manager)
What I did?
- Reinstalled my windows (no problem for me as I only keep system files on partition c)
- Disabled driver verification (windows 10 thing)
- Installed zuk driver, adb , mi tools inside partition c(all inside a folder called zuk)
- used cable that came with phone instead of 3rd party to deep flash
AstroBiswas said:
This Procedure Can Also Be Used To Flash Stock Rom And To Regain Warranty
Scenarios-
1.You Somehow relocked your bootloader while on custom rom
2.Your phone flashes the zuk logo and then screen goes blank with led blinking and you cant see the options to go to fastboot or other modes
3.Your Phone Shows port 9008 or 900e while connected to PC
3.You want to regain your warranty
4.You just want to go back to stock rom
This Guide Is for All of the Above Sceneriaos
Following this guide will revert your phone back to stock ROM nougat while deleting your user data and relocking your bootloader
WARNING
If your device is already bricked and if it goes worse than I am not responsible for it. Do at your own risk.
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
B)QPST ROM
1.Indian Version Nougat http://www.mediafire.com/file/f86cs...SER_Q01080.2_N_ZUI_2.5.104_ST_170418_QPST.zip
2.Chinese Version Nougat
http://s.bs.zui.com/DGDc
Extract these rom to preferably a new folder in the root of c drive
STEPS
INSTALL ALL TOOLS AND DRIVERS GIVEN ABOVE
A)If phone is running fine
1.Enable USB Debugging on your Device and give permission to any prompts
2.Open Minimal ADB and Fastboot and put the following command
adb reboot edl
OR
Put the phone in fastboot mode, Open Minimal ADB and Fastboot and put the following command
fastboot reboot edl
3.Close Window
4.Open Mi Flash Tool
5.Click "select" button on the upper left and browse to the directory where you extracted your stock rom and click refresh on the right COM port shall appear below
6.Click Flash
7.DONT REMOVE OR DISCONNECT THE USB CABLE FLASHING WILL TAKE SOME TIME
8.After success is shown press the power button for sometime until the phone vibrates first boot will take some time
9.Tada! You are back to stock rom along with your WARRANTY!(If Mi flash doesnt work use QFIL as per given in the steps 1 to 4 given below)
B)If phone doesnt bootup
1. Restart your PC and open QFILClick
2. Select "Flat Build" and "Browse". Now navigate to the extracted ROM/Firmware, and select prog_emmc_firehose_8996_ddr.elf.
3.Select the "load xml" button. This will appear a new explorer. One of them will be needed to navigate to the file
rawprogram0.xml the second one will ask for patch0.xml
4.Turn your phone off. Now press and hold the volume + button, while pressing the power button for 0.5 seconds and plug in the
USB cable in the same moment. If it was successful your phone should appear at QPST/QFIL and you are able to press the
download button. Press the download process and wait to finish.
If it fails, In QFIL Change
"Device Type" to eMMC
"Validation Mode" to 0-No validation
"Reset after Download" no needed to tick (optional)
5.If your phone is not detected in the QFIL or it shows up as port 900E then there are 2 ways to get to 9008 mode
I)
a.Unplug your phone from the computer.
b. Press and hold the POWER button until your phone restarting 3-5 times.
c. After the 3rd times (or more), you will see the notification LED goes off in the middle of boot process, and at that time, quick
press VOLUME + button and release the POWER button but keep the VOLUME + button pressed.
d. Your phone will be at POWER OFF status.
e. After your phone is completely off, press and hold the VOLUME +, then press POWER button and connect your USB at the
same time.
f. Your computer will showing a notification about a new port.
g. If you succeed, you will see Diagnostic Port 9008 at QFIL software
II)
Right click on my computer and select MANAGE, then select Device Manager
See if your device is connected as Diagnostic Port 900E
If it is shown as “QHSUSB_BULK” under Other Device
a. Right-click on QHSUSB_BULK and choose “Update Driver Software“
b. Now click on the Browse button and locate the extracted Qualcomm QDLoader drivers.
c. The installation process shall take place immediately and a system notification will appear. Just choose “Install this driver software anyway“.
d.Click the Close button and check back at Device Manager window. You will now see “Qualcomm HS-USB QDLoader 9008 (COM10)” under Ports (COM & LPT) section.
6. Flash your phone using QFIL software once phone connects in 9008 mode and then reboot.
(Alternatively you can also use the Mi Flash Tool once the phone is in 9008 port)
7.Tada! You have successfully unbricked your phone and regained your WARRANTY!
Update: For saving your user data if your phone gets bricked by bootloader getting locked ONLY follow the below guide
How To-
1. How to switch it off
-firstly this is happening because you have locked you're bootloader
- You have black screen and led on so just hold power button then Zuk logo will be flash after that you will get black screen again and again the phone was preparing to reboot but before that the led will get turn off immediately release power button
- You have it Your phone is switched off
(Let it reboot once after that don't leave the power button and after that led will get off for small time this is the time you have to remove finger from power button this is tricky )
2. Going to Bootloader
-Firstly connect the USB to laptop
-after you have switched off your phone press volume up and down together and with holding buttons connect the phone to USB and you will see the fastboot mode
3. Unlock your phone
-Remember the unlock bootloader file in your email re download it and unlock your bootloader again(no need to redownload if you already have it the file is permanent)
- after unlocking phone you will see phone rebooted press power button reboot press volume the volume button and go to reboot option
- go to fastboot and flash the TWRP and you will see that your data on internal storage is present so flash any ROM and you will see your data
Update: Deep flash using Deep Flash Cable And Procedure to make a deep flash cable
Cut the outer rubber and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
After flashing carefully cover the cut portion by putting the rubber casing first and then covering with electrical tape.
So be careful not to tear anything you just need to precisely cut the covering (around 0.5 cm) in the shape of a ring
Happy Flashing!
Click to expand...
Click to collapse
Okay fine, somebody suggested me to flash stock ROM via qpst method, because I was having battery issues, the flashing process stopped, and I forgot to untick clean all and lock, this left my phone with a screen saying, 'unable to boot'. PC is not detecting my device now, but earlier I unlocked bootloader and flashed tw recovery, but I wasn't able to boot to it, and on qpst, my phone is detected as Diagnostic Port 900E.
AstroBiswas said:
This Procedure Can Also Be Used To Flash Stock Rom And To Regain Warranty
Scenarios-
1.You Somehow relocked your bootloader while on custom rom
2.Your phone flashes the zuk logo and then screen goes blank with led blinking and you cant see the options to go to fastboot or other modes
3.Your Phone Shows port 9008 or 900e while connected to PC
3.You want to regain your warranty
4.You just want to go back to stock rom
This Guide Is for All of the Above Sceneriaos
Following this guide will revert your phone back to stock ROM nougat while deleting your user data and relocking your bootloader
WARNING
If your device is already bricked and if it goes worse than I am not responsible for it. Do at your own risk.
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
B)QPST ROM
1.Indian Version Nougat http://www.mediafire.com/file/f86cs...SER_Q01080.2_N_ZUI_2.5.104_ST_170418_QPST.zip
2.Chinese Version Nougat
http://s.bs.zui.com/DGDc
Extract these rom to preferably a new folder in the root of c drive
STEPS
INSTALL ALL TOOLS AND DRIVERS GIVEN ABOVE
A)If phone is running fine
1.Enable USB Debugging on your Device and give permission to any prompts
2.Open Minimal ADB and Fastboot and put the following command
adb reboot edl
OR
Put the phone in fastboot mode, Open Minimal ADB and Fastboot and put the following command
fastboot reboot edl
3.Close Window
4.Open Mi Flash Tool
5.Click "select" button on the upper left and browse to the directory where you extracted your stock rom and click refresh on the right COM port shall appear below
6.Click Flash
7.DONT REMOVE OR DISCONNECT THE USB CABLE FLASHING WILL TAKE SOME TIME
8.After success is shown press the power button for sometime until the phone vibrates first boot will take some time
9.Tada! You are back to stock rom along with your WARRANTY!(If Mi flash doesnt work use QFIL as per given in the steps 1 to 4 given below)
B)If phone doesnt bootup
1. Restart your PC and open QFILClick
2. Select "Flat Build" and "Browse". Now navigate to the extracted ROM/Firmware, and select prog_emmc_firehose_8996_ddr.elf.
3.Select the "load xml" button. This will appear a new explorer. One of them will be needed to navigate to the file
rawprogram0.xml the second one will ask for patch0.xml
4.Turn your phone off. Now press and hold the volume + button, while pressing the power button for 0.5 seconds and plug in the
USB cable in the same moment. If it was successful your phone should appear at QPST/QFIL and you are able to press the
download button. Press the download process and wait to finish.
If it fails, In QFIL Change
"Device Type" to eMMC
"Validation Mode" to 0-No validation
"Reset after Download" no needed to tick (optional)
5.If your phone is not detected in the QFIL or it shows up as port 900E then there are 2 ways to get to 9008 mode
I)
a.Unplug your phone from the computer.
b. Press and hold the POWER button until your phone restarting 3-5 times.
c. After the 3rd times (or more), you will see the notification LED goes off in the middle of boot process, and at that time, quick
press VOLUME + button and release the POWER button but keep the VOLUME + button pressed.
d. Your phone will be at POWER OFF status.
e. After your phone is completely off, press and hold the VOLUME +, then press POWER button and connect your USB at the
same time.
f. Your computer will showing a notification about a new port.
g. If you succeed, you will see Diagnostic Port 9008 at QFIL software
II)
Right click on my computer and select MANAGE, then select Device Manager
See if your device is connected as Diagnostic Port 900E
If it is shown as “QHSUSB_BULK” under Other Device
a. Right-click on QHSUSB_BULK and choose “Update Driver Software“
b. Now click on the Browse button and locate the extracted Qualcomm QDLoader drivers.
c. The installation process shall take place immediately and a system notification will appear. Just choose “Install this driver software anyway“.
d.Click the Close button and check back at Device Manager window. You will now see “Qualcomm HS-USB QDLoader 9008 (COM10)” under Ports (COM & LPT) section.
6. Flash your phone using QFIL software once phone connects in 9008 mode and then reboot.
(Alternatively you can also use the Mi Flash Tool once the phone is in 9008 port)
7.Tada! You have successfully unbricked your phone and regained your WARRANTY!
Update: For saving your user data if your phone gets bricked by bootloader getting locked ONLY follow the below guide
How To-
1. How to switch it off
-firstly this is happening because you have locked you're bootloader
- You have black screen and led on so just hold power button then Zuk logo will be flash after that you will get black screen again and again the phone was preparing to reboot but before that the led will get turn off immediately release power button
- You have it Your phone is switched off
(Let it reboot once after that don't leave the power button and after that led will get off for small time this is the time you have to remove finger from power button this is tricky )
2. Going to Bootloader
-Firstly connect the USB to laptop
-after you have switched off your phone press volume up and down together and with holding buttons connect the phone to USB and you will see the fastboot mode
3. Unlock your phone
-Remember the unlock bootloader file in your email re download it and unlock your bootloader again(no need to redownload if you already have it the file is permanent)
- after unlocking phone you will see phone rebooted press power button reboot press volume the volume button and go to reboot option
- go to fastboot and flash the TWRP and you will see that your data on internal storage is present so flash any ROM and you will see your data
Update: Deep flash using Deep Flash Cable And Procedure to make a deep flash cable
Cut the outer rubber and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
After flashing carefully cover the cut portion by putting the rubber casing first and then covering with electrical tape.
So be careful not to tear anything you just need to precisely cut the covering (around 0.5 cm) in the shape of a ring
Happy Flashing!
Click to expand...
Click to collapse
What if the phone even won't boot tofastboot mode?? It only vibrates every 10 sec or maybe, will EDL cable work??
Can anybody help
sagarsk said:
Not even coming up as 900E
My hard brick z2 is not even coming up as 900E. Basically computer doesn't detect and no changes in device manager either. Please confirm what to do.
I have tried pressing buttons told by many others and in various other forums. It doesn't work. Does deep flash cable method work even if the phone is not detecting in 900E mode?
Click to expand...
Click to collapse
I also have the same question and I am in the same situation
Hello there members.
i have a Nothing Phone 1 in Edl Mode. Tried to restart it but still connected on Edl. i have searched around for this problem but sill unlucky to find a solution.
Client pretend to have played with roms and flashed the wrong one.
Any help suggestion?
pogradecari said:
Hello there members.
i have a Nothing Phone 1 in Edl Mode. Tried to restart it but still connected on Edl. i have searched around for this problem but sill unlucky to find a solution.
Client pretend to have played with roms and flashed the wrong one.
Any help suggestion?
Click to expand...
Click to collapse
Try holding power+volup+voldown with the phone unplugged from a computer.
If it doesn't work, let me know.
how to boot to edl mode ??
Try this :
Install ADB and Minimal Fastboot drivers through which Windows will recognize your Device.
Enable USB Debugging on your Android Device. You can do this simply by following the given direction:
Settings > About Phone > tap 7 times on the Build Number. This will enable Developer options on it.
Now, again go back to the main Settings > Developer options > USB Debugging and Enable it.
Connect your smartphone with your PC via a USB cable.
Open Command Window by the press and hold Shift Key + right-click of your Mouse.
Choose Open Command Window here.
Type the following command and press the Enter button to check whether the device is connected or not.
" adb devices "
You will see a device serial code on the screen. That means it is successfully connected. Then follow the next step.
Type the command from below and hit enter to Boot into Download Mode (EDL Mode):
" adb reboot edl " or "fastboot oem edl" or "fastboot reboot-edl" or "fastboot reboot edl"
muppetz said:
Try this :
Install ADB and Minimal Fastboot drivers through which Windows will recognize your Device.
Enable USB Debugging on your Android Device. You can do this simply by following the given direction:
Settings > About Phone > tap 7 times on the Build Number. This will enable Developer options on it.
Now, again go back to the main Settings > Developer options > USB Debugging and Enable it.
Connect your smartphone with your PC via a USB cable.
Open Command Window by the press and hold Shift Key + right-click of your Mouse.
Choose Open Command Window here.
Type the following command and press the Enter button to check whether the device is connected or not.
" adb devices "
You will see a device serial code on the screen. That means it is successfully connected. Then follow the next step.
Type the command from below and hit enter to Boot into Download Mode (EDL Mode):
" adb reboot edl "
Click to expand...
Click to collapse
my phone is bricked while flashing stock rom via fastboot
so unable to boot to recovery or bootloader
To begin with, power off your device. If you can’t do so, then you will have to wait until the battery completely drains out.
Now connect one end of the USB cable to your PC, but don’t attach the other end to the device.
Press and hold the Volume Up and Volume Down buttons together for a few seconds.
Now connect the other end of the device to the USB cable.
Your device will now be recognized as Qualcomm HS-USB QDLoader 9008. You may now flash the device-specific firmware to unbrick it.
Even you have a black screen , PC does recognize your phone . Use only a USB 2.0 port . Verify if Qualcomm USB Driver have been installed on Windows .
muppetz said:
To begin with, power off your device. If you can’t do so, then you will have to wait until the battery completely drains out.
Now connect one end of the USB cable to your PC, but don’t attach the other end to the device.
Press and hold the Volume Up and Volume Down buttons together for a few seconds.
Now connect the other end of the device to the USB cable.
Your device will now be recognized as Qualcomm HS-USB QDLoader 9008. You may now flash the device-specific firmware to unbrick it.
Even you have a black screen , PC does recognize your phone . Use only a USB 2.0 port . Verify if drivers have been installed on Windows .
Click to expand...
Click to collapse
tried these steps but phone goes in 900E mode
OK , look then at this :
muppetz said:
OK , look then at this :
Click to expand...
Click to collapse
it does not work as he just changed the drivers from diagnostic mode to qdloader mode
pogradecari said:
Hello there members.
i have a Nothing Phone 1 in Edl Mode. Tried to restart it but still connected on Edl. i have searched around for this problem but sill unlucky to find a solution.
Client pretend to have played with roms and flashed the wrong one.
Any help suggestion?
Click to expand...
Click to collapse
Maybe it's too late already but you can unbrick the phone with this tool
Unbrick / Flash Stock Rom (1.1.7 global) QDLoader 9008 fix | EDL Mode fix
Hi everyone, If your phone (1) does not react on any of yours actions. You may have the same problem. This is an instruction how to fix it without Disassembly. ‼️ Do this at your own risk, I am not responsible for any damage that may occur to...
forum.xda-developers.com
none of these will work
pogradecari said:
none of these will work
Click to expand...
Click to collapse
Why? Have you tried?