Related
Okay im running windows xp, and i have all those drivers installed...
http://www.userdrivers.com/PDA-Mobil...dows-XP-Vista/
and http://drivers.softpedia.com/get/MOBILES/Samsung/Samsung-Galaxy-S-USB-Driver-for-Windows-x86.shtml
so what am i missing to get my vibrant to be recognised by odin in download mode????
What are you running currently?
simply honey 3.6..... gingerbread
By chance did you forget to enable usb debugging?
idk, i flashed from a 2.2.1 rom to simply honey 3.6 through rom manager, but i did have it enabled through before i flashed for sure.... And usb debugging is not required for download mode as (i think) thats a whole different thing???
It needs to be enabled to use Odin. Also, sometimes for Odin to see my phone I have to unplug my phone and open Odin a few times before I finally get Odin to see my phone. It's very finicky for me, always has been
Sent from my SGH-T959 using XDA Premium App
helikido said:
Okay im running windows xp, and i have all those drivers installed...
http://www.userdrivers.com/PDA-Mobil...dows-XP-Vista/
and http://drivers.softpedia.com/get/MOBILES/Samsung/Samsung-Galaxy-S-USB-Driver-for-Windows-x86.shtml
so what am i missing to get my vibrant to be recognised by odin in download mode????
Click to expand...
Click to collapse
Go into windows device manager. Make sure that your computer is even seeing the device and that it has recognized the drivers for it. If it recognizes it, try rebooting computer then restart the process. Also make sure your phone is actually in DOWNLOAD mode. Not Recovery mode.
If you do not know the difference between the two, let us now and we'll assist further.
Happy hacking!
I use to always have trouble with Odin..then one day someone mentioned they always right clicked on Odin and chose "run as Administrator", I have never done that because I figured I was the administrator....but once I did it, never had a problem since.
Another problem I run into (well not anymore) is the USB port I plugged into. If I was on a hub or something it wouldn't work. If I plug right into my computer it works properly.
I also use adb commands to get into download and recovery when I'm Odin'ing. It also let's me know if my phone is detected by the OS.
#adb devices (should show your phone listed)
#adb reboot download (reboots your phone into download mode)
#adb reboot recovery (reboots your phone into recovery mode)
You'll need the SDK installed for adb to work.
Since I started doing these things, I have had ZERO problems with Odin and flashing my phone.
ay.. usb debuging was enabled before i flashed... now if my turn turns on it goee onto a bootloop... so everytime i cinnect my phone to the computer it says device not recognised. ohh and one thing to mention is that my computer doesnt have a highspeed usb port
Three button to download mode - power+vol up+vol down and see if you can get it into download mode then plug in usb (1.0 should work), then run odin...
otherwise i think you're looking at trying to make one of those jigs or replacing your phone...
try
1. Start Odin
2. Plug USB cable into pc
3. Power off the Phone.
3. Pull the Battery.
5. Plug USB cable into Phone.
6. Press and Hold: Volume UP + Volume DOWN + Power, all at the same time.
7. Re-insert the battery.
8. The phone will power now, when the screen starts a cycle of going to a BLACK screen, release ONLY the POWER button.
9. When you see the download icon release the volume buttons,
10. Odin back to stock by putting the PIT file into the appropriate area and the .tar in the PDA area.
Afaik the three button combo is for
Recovery mode. Follow the above directions up to the power button part. While holding both volume buttons, it should go directly into download mode when the usb us plugged in
Try removing all drivers then reinstall if xp doesn't pick it up
Beware of angry gingerbread man
power off phone
pull out battery
turn on odin
attach phone to pc with usb cable
now while holding down both volume buttons put battery back in.
now you should be in download mode and go back to stock with odin from here!
Enjoy and also make sure u have the proper samsung drivers
Install samsung kies mini. It gives you the correct drivers. I once installed those and it messed it up. So install kies mini.
adamcooks said:
Afaik the three button combo is for
Recovery mode. Follow the above directions up to the power button part. While holding both volume buttons, it should go directly into download mode when the usb us plugged in
Try removing all drivers then reinstall if xp doesn't pick it up
Beware of angry gingerbread man
Click to expand...
Click to collapse
This is what happens when you do it a certain way for a long time, you forget certain things...lol
try another computer?
goodluck
I am sure I have properly installed usb driver for my nexus 7, since I have unlocked and rooted my device.
When I reboot my device to bootloader, my PC detected a new device connected, but fail to recognize it.
Also, I can't do anything when I am in fastboot mode, e.g. no effect for pressing power, vol + or vol - button.
Now, I want to return to 4.1.2 stock image, but I cannot do that on fastboot mode.
Any solution/ work arround to save my device??
Looks like drivers got screwy.. Install PDANet and let it install the drivers for your device..
http://junefabrics.com/android/download.php
One your drivers are up to snuff and you can access your device when in the bootloader again you can remove PDANet and the usb drivers will stay in place.
styckx said:
Looks like drivers got screwy.. Install PDANet and let it install the drivers for your device..
http://junefabrics.com/android/download.php
One your drivers are up to snuff and you can access your device when in the bootloader again you can remove PDANet and the usb drivers will stay in place.
Click to expand...
Click to collapse
I re-installed driver by PDANet, still I can connect Nexus 7 on normal state, but not in bootloader/ fastboot mode.
I am guessing the fastboot is dead and not related to usb driver issue.
Since there is no any response when I am pressing the button. The fastboot mode is hanged.
The drivers have been tricky with the Amazon Fire to say the least, and this seems to be because windows recognizes the driver as unsigned. To get around this issue, you will need to temporarily enable installation of drivers that are unsigned.
First go to Settings>Update and recovery.
from there click on advanced startup.
Your PC should say "please wait" then pull up a menu.
In this menu click on "troubleshoot" then click "start up settings"
Your PC will now restart
The PC will now boot into Startup Settings. Click 7 on your keyboard to disable driver enforcement then hit enter.
Your PC will restart once more.
Now your fire drivers should install as they are intended. Allowing installation of unsigned drivers can be a security risk, so once you have completed this process and installed the drivers reboot your PC and windows will automatically turn Driver Signature Verification on once again.
its smart to uninstall the fire drivers and reinstall them using the driver signature mode to make sure theyre installed correctly.
its also worth noting that in my case, the device needed a different driver from the downloaded for each mode (normal/on, fastboot, sideload), there is another thread on here for this but Ill add it here just in case someone else stumbles upon this first.
when installing the drivers in device signature mode, youll want to put the device in all 3 states while in signature mode to make sure you dont run into any problems trying to return the device to stock or moving on from fastboot etc. ( i did this, it was scary..)
1. when installing the drivers in signature mode youll come across 3 different drivers to choose from, the first driver "android ABD interface" is for when the device is in normal/on mode.
2. youll need to next boot the device into fastboot mode, i used the rootjunky amazon fire supertool and booted the device to fastboot, then disconnect and reconnected it to my pc and chose the second adb usb driver "android bootloader interface"
2. after installing that driver disconnect the device from the computer and power it down. power the device into the recovery mode by shutting it down then holding volume down and power (when holding the device in portrait orientation the volume down button is the one to the left) and navigate to the option that requires you to connect your device to a PC to load software (sorry i cant remember what option it is) it will say something like its waiting for a connection, connect the device to the PC and install the final driver "android composite ADB interface" now every facet of operation should have a driver, reboot your PC out of driver signature mode and if you were in the same boat as me, you should be able to sideload back to the android os, and flash roms or whatever else.
MSM8994DownloadTool.exe Won't Work For Me
I need help.
My phone is stuck on the fastboot screen, meaning I can only Power if off and into Fastboot (using the Vol+ and Power buttons). Other than that, it does nothing. I cannot get into the OS at all, which means I can't enable USB debugging or anything. Fastboot recognizes my device, which is a OnePlus Two), but ADB won't, nor will my Windows 7 PC as a USB device. With that in mind, I followed all the steps in the posted guide. I get all the way to running the "MSM8994DownloadTool.exe" and nothing happens. Its as if the Recovery Tool doesn't even see my device. So, I'm really stuck and don't know what to do.
For clarity, here's exactly what I did (see below). I get all the way to Section B, Step 2 and that's where it breaks down. There's no different line, and no process ever runs, even after waiting 30 minutes. I ran the tool as Administrator, but still no luck. Can anyone help me? Just as additional info, my Mac also does not recognize my OPT as a USB device. Also, I tried my backup USB-C cable from the OEM, with the same results.
A. Install the Certificates followed by the Qualcomm drivers.
1. Restart your computer with Driver Signature Enforcement Disabled (Advanced Startup) Let me Google it For You
2. Open the folder "qc" and install the Test Certificate in the following Stores: Trusted Root, Trusted Publisher, Third-Party Root and Personal
3. Run the Qualcomm setup wizard (also located in the qc folder)
4. When completed, restart your PC again with Driver Signature Enforcement Disabled (Advanced Startup)
5. Turn off your phone and disconnect the USB cable from the phone.
6. Hold vol-up and plug in the USB(Do not press Power button). The screen will stay black but you will hear a sound from windows that a device is attached.
7. The driver should now automatically install. If not, go to device manager and right click "Unknown Device" and click "Update Driver" Search up the QC folder and press ok. The driver should now install. (Got the RELINK issue? Take a look here: http://forum.xda-developers.com/show...1&postcount=46)
B. Flashing Process
1. Open the OnePlus2_14_A.11_151211 folder and open "MSM8994DownloadTool.exe"
2. Look if your phone is detected in the list. everything is Chinese but you will see one row with different chinese text from the rest within the list. If not, recheck if driver is detected in Device Manager (If not, go back to Step A - Line 4).
I think you have a bad download, try downloading it again and download the 3.0.2 version if you can.
Phil01234 said:
MSM8994DownloadTool.exe Won't Work For Me
I need help.
My phone is stuck on the fastboot screen, meaning I can only Power if off and into Fastboot (using the Vol+ and Power buttons). Other than that, it does nothing. I cannot get into the OS at all, which means I can't enable USB debugging or anything. Fastboot recognizes my device, which is a OnePlus Two), but ADB won't, nor will my Windows 7 PC as a USB device. With that in mind, I followed all the steps in the posted guide. I get all the way to running the "MSM8994DownloadTool.exe" and nothing happens. Its as if the Recovery Tool doesn't even see my device. So, I'm really stuck and don't know what to do.
For clarity, here's exactly what I did (see below). I get all the way to Section B, Step 2 and that's where it breaks down. There's no different line, and no process ever runs, even after waiting 30 minutes. I ran the tool as Administrator, but still no luck. Can anyone help me? Just as additional info, my Mac also does not recognize my OPT as a USB device. Also, I tried my backup USB-C cable from the OEM, with the same results.
A. Install the Certificates followed by the Qualcomm drivers.
1. Restart your computer with Driver Signature Enforcement Disabled (Advanced Startup) Let me Google it For You
2. Open the folder "qc" and install the Test Certificate in the following Stores: Trusted Root, Trusted Publisher, Third-Party Root and Personal
3. Run the Qualcomm setup wizard (also located in the qc folder)
4. When completed, restart your PC again with Driver Signature Enforcement Disabled (Advanced Startup)
5. Turn off your phone and disconnect the USB cable from the phone.
6. Hold vol-up and plug in the USB(Do not press Power button). The screen will stay black but you will hear a sound from windows that a device is attached.
7. The driver should now automatically install. If not, go to device manager and right click "Unknown Device" and click "Update Driver" Search up the QC folder and press ok. The driver should now install. (Got the RELINK issue? Take a look here: http://forum.xda-developers.com/show...1&postcount=46)
B. Flashing Process
1. Open the OnePlus2_14_A.11_151211 folder and open "MSM8994DownloadTool.exe"
2. Look if your phone is detected in the list. everything is Chinese but you will see one row with different chinese text from the rest within the list. If not, recheck if driver is detected in Device Manager (If not, go back to Step A - Line 4).
Click to expand...
Click to collapse
I've bricked my op2 a while ago. I'm a real noob so I don't know if it will work but have you installed the adb mac drivers or try "fastboot continue" while in fastboot. Just don't give up and keep try. You have absolutely nothing to lose.
chintu1234 said:
I think you have a bad download, try downloading it again and download the 3.0.2 version if you can.
Click to expand...
Click to collapse
Thank you very much. I have the latest version, but still nothing. I don't know if this has anything to do with it, but my OPT wasn't being recognized as a USB device even before I screwed up. That leads me to believe my OPT USB is maybe not functional. ADB doesn't recognize it at, nor will the MP...DownloadTool.exe. I'm guessing it is just hard-bricked since I have no other way (besides USB) to interface with the device.
Phil01234 said:
Thank you very much. I have the latest version, but still nothing. I don't know if this has anything to do with it, but my OPT wasn't being recognized as a USB device even before I screwed up. That leads me to believe my OPT USB is maybe not functional. ADB doesn't recognize it at, nor will the MP...DownloadTool.exe. I'm guessing it is just hard-bricked since I have no other way (besides USB) to interface with the device.
Click to expand...
Click to collapse
Try connecting your OPT to some other guys pc and see, it may be because of your pc's end that its not getting connected.
And if the same thing happens with a different pc then yeah your usb port or something is fried. Try going to service center if the same thing happens again.
This Procedure Can Also Be Used To Flash Stock Rom And To Regain Warranty
Scenarios-
1.You Somehow relocked your bootloader while on custom rom
2.Your phone flashes the zuk logo and then screen goes blank with led blinking and you cant see the options to go to fastboot or other modes
3.Your Phone Shows port 9008 or 900e while connected to PC
3.You want to regain your warranty
4.You just want to go back to stock rom
This Guide Is for All of the Above Sceneriaos
Following this guide will revert your phone back to stock ROM nougat while deleting your user data and relocking your bootloader
WARNING
If your device is already bricked and if it goes worse than I am not responsible for it. Do at your own risk.
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
B)QPST ROM
1.Indian Version Nougat http://www.mediafire.com/file/f86cs...SER_Q01080.2_N_ZUI_2.5.104_ST_170418_QPST.zip
2.Chinese Version Nougat
http://s.bs.zui.com/DGDc
Extract these rom to preferably a new folder in the root of c drive
STEPS
INSTALL ALL TOOLS AND DRIVERS GIVEN ABOVE
A)If phone is running fine
1.Enable USB Debugging on your Device and give permission to any prompts
2.Open Minimal ADB and Fastboot and put the following command
adb reboot edl
OR
Put the phone in fastboot mode, Open Minimal ADB and Fastboot and put the following command
fastboot reboot edl
3.Close Window
4.Open Mi Flash Tool
5.Click "select" button on the upper left and browse to the directory where you extracted your stock rom and click refresh on the right COM port shall appear below
6.Click Flash
7.DONT REMOVE OR DISCONNECT THE USB CABLE FLASHING WILL TAKE SOME TIME
8.After success is shown press the power button for sometime until the phone vibrates first boot will take some time
9.Tada! You are back to stock rom along with your WARRANTY!(If Mi flash doesnt work use QFIL as per given in the steps 1 to 4 given below)
B)If phone doesnt bootup
1. Restart your PC and open QFILClick
2. Select "Flat Build" and "Browse". Now navigate to the extracted ROM/Firmware, and select prog_emmc_firehose_8996_ddr.elf.
3.Select the "load xml" button. This will appear a new explorer. One of them will be needed to navigate to the file
rawprogram0.xml the second one will ask for patch0.xml
4.Turn your phone off. Now press and hold the volume + button, while pressing the power button for 0.5 seconds and plug in the
USB cable in the same moment. If it was successful your phone should appear at QPST/QFIL and you are able to press the
download button. Press the download process and wait to finish.
If it fails, In QFIL Change
"Device Type" to eMMC
"Validation Mode" to 0-No validation
"Reset after Download" no needed to tick (optional)
5.If your phone is not detected in the QFIL or it shows up as port 900E then there are 2 ways to get to 9008 mode
I)
a.Unplug your phone from the computer.
b. Press and hold the POWER button until your phone restarting 3-5 times.
c. After the 3rd times (or more), you will see the notification LED goes off in the middle of boot process, and at that time, quick
press VOLUME + button and release the POWER button but keep the VOLUME + button pressed.
d. Your phone will be at POWER OFF status.
e. After your phone is completely off, press and hold the VOLUME +, then press POWER button and connect your USB at the
same time.
f. Your computer will showing a notification about a new port.
g. If you succeed, you will see Diagnostic Port 9008 at QFIL software
II)
Right click on my computer and select MANAGE, then select Device Manager
See if your device is connected as Diagnostic Port 900E
If it is shown as “QHSUSB_BULK” under Other Device
a. Right-click on QHSUSB_BULK and choose “Update Driver Software“
b. Now click on the Browse button and locate the extracted Qualcomm QDLoader drivers.
c. The installation process shall take place immediately and a system notification will appear. Just choose “Install this driver software anyway“.
d.Click the Close button and check back at Device Manager window. You will now see “Qualcomm HS-USB QDLoader 9008 (COM10)” under Ports (COM & LPT) section.
6. Flash your phone using QFIL software once phone connects in 9008 mode and then reboot.
(Alternatively you can also use the Mi Flash Tool once the phone is in 9008 port)
7.Tada! You have successfully unbricked your phone and regained your WARRANTY!
Update: For saving your user data if your phone gets bricked by bootloader getting locked ONLY follow the below guide
How To-
1. How to switch it off
-firstly this is happening because you have locked you're bootloader
- You have black screen and led on so just hold power button then Zuk logo will be flash after that you will get black screen again and again the phone was preparing to reboot but before that the led will get turn off immediately release power button
- You have it Your phone is switched off
(Let it reboot once after that don't leave the power button and after that led will get off for small time this is the time you have to remove finger from power button this is tricky )
2. Going to Bootloader
-Firstly connect the USB to laptop
-after you have switched off your phone press volume up and down together and with holding buttons connect the phone to USB and you will see the fastboot mode
3. Unlock your phone
-Remember the unlock bootloader file in your email re download it and unlock your bootloader again(no need to redownload if you already have it the file is permanent)
- after unlocking phone you will see phone rebooted press power button reboot press volume the volume button and go to reboot option
- go to fastboot and flash the TWRP and you will see that your data on internal storage is present so flash any ROM and you will see your data
Update: Deep flash using Deep Flash Cable And Procedure to make a deep flash cable
Cut the outer rubber and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
After flashing carefully cover the cut portion by putting the rubber casing first and then covering with electrical tape.
So be careful not to tear anything you just need to precisely cut the covering (around 0.5 cm) in the shape of a ring
Happy Flashing!
I think someone has made this guide already.
I see.
well i have a similar issue that i am stuck at 9008 port that is edl but, i can flash rom via Qfil and Mi Flash toll but i cant boot onto it=
I cant get out of edl mode lol. stuck at it.
I deleted some files from qpst rom for intentionally hard bricking my phone and heres another fix.
Cut the outer plastic and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
Happy Flashing!
AstroBiswas said:
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994 - not last edition, latest is v1.0.8
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270 - not last edition, latest is 2.7.460 (fix "sahara" error)
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download - not needed
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790 - not needed (if you use the previous paragraph).
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
Click to expand...
Click to collapse
@AstroBiswas Read red comment.
Not_James_Bond said:
I think someone has made this guide already.
Click to expand...
Click to collapse
Of course!
https://forum.xda-developers.com/le...-to-recover-hard-bricked-zuk-z2-plus-t3576007
Not even coming up as 900E
AstroBiswas said:
This Procedure Can Also Be Used To Flash Stock Rom And To Regain Warranty
Scenarios-
1.You Somehow relocked your bootloader while on custom rom
2.Your phone flashes the zuk logo and then screen goes blank with led blinking and you cant see the options to go to fastboot or other modes
3.Your Phone Shows port 9008 or 900e while connected to PC
3.You want to regain your warranty
4.You just want to go back to stock rom
This Guide Is for All of the Above Sceneriaos
Following this guide will revert your phone back to stock ROM nougat while deleting your user data and relocking your bootloader
WARNING
If your device is already bricked and if it goes worse than I am not responsible for it. Do at your own risk.
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
B)QPST ROM
1.Indian Version Nougat http://www.mediafire.com/file/f86cs...SER_Q01080.2_N_ZUI_2.5.104_ST_170418_QPST.zip
2.Chinese Version Nougat
http://s.bs.zui.com/DGDc
Extract these rom to preferably a new folder in the root of c drive
STEPS
INSTALL ALL TOOLS AND DRIVERS GIVEN ABOVE
A)If phone is running fine
1.Enable USB Debugging on your Device and give permission to any prompts
2.Open Minimal ADB and Fastboot and put the following command
adb reboot edl
OR
Put the phone in fastboot mode, Open Minimal ADB and Fastboot and put the following command
fastboot reboot edl
3.Close Window
4.Open Mi Flash Tool
5.Click "select" button on the upper left and browse to the directory where you extracted your stock rom and click refresh on the right COM port shall appear below
6.Click Flash
7.DONT REMOVE OR DISCONNECT THE USB CABLE FLASHING WILL TAKE SOME TIME
8.After success is shown press the power button for sometime until the phone vibrates first boot will take some time
9.Tada! You are back to stock rom along with your WARRANTY!(If Mi flash doesnt work use QFIL as per given in the steps 1 to 4 given below)
B)If phone doesnt bootup
1. Restart your PC and open QFILClick
2. Select "Flat Build" and "Browse". Now navigate to the extracted ROM/Firmware, and select prog_emmc_firehose_8996_ddr.elf.
3.Select the "load xml" button. This will appear a new explorer. One of them will be needed to navigate to the file
rawprogram0.xml the second one will ask for patch0.xml
4.Turn your phone off. Now press and hold the volume + button, while pressing the power button for 0.5 seconds and plug in the
USB cable in the same moment. If it was successful your phone should appear at QPST/QFIL and you are able to press the
download button. Press the download process and wait to finish.
If it fails, In QFIL Change
"Device Type" to eMMC
"Validation Mode" to 0-No validation
"Reset after Download" no needed to tick (optional)
5.If your phone is not detected in the QFIL or it shows up as port 900E then there are 2 ways to get to 9008 mode
I)
a.Unplug your phone from the computer.
b. Press and hold the POWER button until your phone restarting 3-5 times.
c. After the 3rd times (or more), you will see the notification LED goes off in the middle of boot process, and at that time, quick
press VOLUME + button and release the POWER button but keep the VOLUME + button pressed.
d. Your phone will be at POWER OFF status.
e. After your phone is completely off, press and hold the VOLUME +, then press POWER button and connect your USB at the
same time.
f. Your computer will showing a notification about a new port.
g. If you succeed, you will see Diagnostic Port 9008 at QFIL software
II)
Right click on my computer and select MANAGE, then select Device Manager
See if your device is connected as Diagnostic Port 900E
If it is shown as “QHSUSB_BULK” under Other Device
a. Right-click on QHSUSB_BULK and choose “Update Driver Software“
b. Now click on the Browse button and locate the extracted Qualcomm QDLoader drivers.
c. The installation process shall take place immediately and a system notification will appear. Just choose “Install this driver software anyway“.
d.Click the Close button and check back at Device Manager window. You will now see “Qualcomm HS-USB QDLoader 9008 (COM10)” under Ports (COM & LPT) section.
6. Flash your phone using QFIL software once phone connects in 9008 mode and then reboot.
(Alternatively you can also use the Mi Flash Tool once the phone is in 9008 port)
7.Tada! You have successfully unbricked your phone and regained your WARRANTY!
Update: For saving your user data if your phone gets bricked by bootloader getting locked ONLY follow the below guide
How To-
1. How to switch it off
-firstly this is happening because you have locked you're bootloader
- You have black screen and led on so just hold power button then Zuk logo will be flash after that you will get black screen again and again the phone was preparing to reboot but before that the led will get turn off immediately release power button
- You have it Your phone is switched off
(Let it reboot once after that don't leave the power button and after that led will get off for small time this is the time you have to remove finger from power button this is tricky )
2. Going to Bootloader
-Firstly connect the USB to laptop
-after you have switched off your phone press volume up and down together and with holding buttons connect the phone to USB and you will see the fastboot mode
3. Unlock your phone
-Remember the unlock bootloader file in your email re download it and unlock your bootloader again(no need to redownload if you already have it the file is permanent)
- after unlocking phone you will see phone rebooted press power button reboot press volume the volume button and go to reboot option
- go to fastboot and flash the TWRP and you will see that your data on internal storage is present so flash any ROM and you will see your data
Update: Deep flash using Deep Flash Cable And Procedure to make a deep flash cable
Cut the outer rubber and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
After flashing carefully cover the cut portion by putting the rubber casing first and then covering with electrical tape.
So be careful not to tear anything you just need to precisely cut the covering (around 0.5 cm) in the shape of a ring
Happy Flashing!
Click to expand...
Click to collapse
My hard brick z2 is not even coming up as 900E. Basically computer doesn't detect and no changes in device manager either. Please confirm what to do.
I have tried pressing buttons told by many others and in various other forums. It doesn't work. Does deep flash cable method work even if the phone is not detecting in 900E mode?
You have to boot in proper edl mode...for edl mode hold volume up button 15 second and immediately click power button for .5 sec and attach data cable to phone which is connected to pc and & immediately prees again power button. all while procees alway hold volume up button....
Zuk Z2 Pro Stuck in EDL HS-USB 9008 Port and automatically connecting and disconnect
Hi,
My Zuk Z2 Pro is stuck in EDL 9008 Port. Phone is totally bricked and no sound, no light, no vibration. When i connect with the computer, phone is connecting on HS USB 9008 port and get disconnected after 20-22 seconds and again automatically connected with in half second time.
I am facing this issue after flashing a ZUI 1.9 by using a QPAST/QFIL application. I think i have made stupid mistake by flashing a phone with "ERASE ALL BEFORE DOWNLOAD" option.
I have tried every scenario to get stable this 9008 port but no luck. Since last 5 days i am studying forums and applying every kind of solution but same result.
I am writing this post with high expectations and hope someone will take notice and help me to get rid of this problem.
I can pay through paypal if someone wants to provide professional services to resolve this matter
I will appreciate if someone have any idea and can help me. Thanks
Can someine please help me with this weird situation? Device got disconnected while flashing via qfil. Now no zuk logo nothing. Phone vibrates every 30 sec that's it. Wont even gets recognized by my laptop(no 9008 or 900e port!)
SilenT__ShadoW said:
Can someine please help me with this weird situation? Device got disconnected while flashing via qfil. Now no zuk logo nothing. Phone vibrates every 30 sec that's it. Wont even gets recognized by my laptop(no 9008 or 900e port!)
Click to expand...
Click to collapse
You need to use the deep flash guide which involved cutting and sorting the cable , procedure given in last part of OP
AstroBiswas said:
You need to use the deep flash guide which involved cutting and sorting the cable , procedure given in last part of OP
Click to expand...
Click to collapse
I've tired that also. Connecting phone to pc while green and black wires attached together and detaching them after 5 sec. That also did nothing. However i connect my phone to my pc it just vibrates and blinks led every 30 sec till i remove battery!
SilenT__ShadoW said:
I've tired that also. Connecting phone to pc while green and black wires attached together and detaching them after 5 sec. That also did nothing. However i connect my phone to my pc it just vibrates and blinks led every 30 sec till i remove battery!
Click to expand...
Click to collapse
You need to completely poweoff the phone (difficult in hard brick actually) before this procedure i have forgotten the way to do it, was given on zuk.eu i think, dont worry it may take time but these days hard bricks is repairable too.
AstroBiswas said:
You need to completely poweoff the phone (difficult in hard brick actually) before this procedure i have forgotten the way to do it, was given on zuk.eu i think, dont worry it may take time but these days hard bricks is repairable too.
Click to expand...
Click to collapse
Isn't removing battery connection means powering off the device???
SilenT__ShadoW said:
Isn't removing battery connection means powering off the device???
Click to expand...
Click to collapse
Yes!
AstroBiswas said:
Yes!
Click to expand...
Click to collapse
I'm doing the same.... Removing battery connection every time to switch off.
SilenT__ShadoW said:
I'm doing the same.... Removing battery connection every time to switch off.
Click to expand...
Click to collapse
Thats strange keep trying, perfect timing matters
AstroBiswas said:
Thats strange keep trying, perfect timing matters
Click to expand...
Click to collapse
What do you mean by perfect timing?!?
Never mind. Got my laptop to recognise it and flashed successfully.
Don't know what made it to change its mind!?
What happened?
- was trying to flash and cable got disconnected by accident.
- my phone started to vibrate and blink at the same time for every 30 sec(no zuk logo nothing) and can't seems to be stopped.
- laptop doesn't seems to recognise when device gets connected (no 900e or 9008 port shows up at device manager)
What I did?
- Reinstalled my windows (no problem for me as I only keep system files on partition c)
- Disabled driver verification (windows 10 thing)
- Installed zuk driver, adb , mi tools inside partition c(all inside a folder called zuk)
- used cable that came with phone instead of 3rd party to deep flash
AstroBiswas said:
This Procedure Can Also Be Used To Flash Stock Rom And To Regain Warranty
Scenarios-
1.You Somehow relocked your bootloader while on custom rom
2.Your phone flashes the zuk logo and then screen goes blank with led blinking and you cant see the options to go to fastboot or other modes
3.Your Phone Shows port 9008 or 900e while connected to PC
3.You want to regain your warranty
4.You just want to go back to stock rom
This Guide Is for All of the Above Sceneriaos
Following this guide will revert your phone back to stock ROM nougat while deleting your user data and relocking your bootloader
WARNING
If your device is already bricked and if it goes worse than I am not responsible for it. Do at your own risk.
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
B)QPST ROM
1.Indian Version Nougat http://www.mediafire.com/file/f86cs...SER_Q01080.2_N_ZUI_2.5.104_ST_170418_QPST.zip
2.Chinese Version Nougat
http://s.bs.zui.com/DGDc
Extract these rom to preferably a new folder in the root of c drive
STEPS
INSTALL ALL TOOLS AND DRIVERS GIVEN ABOVE
A)If phone is running fine
1.Enable USB Debugging on your Device and give permission to any prompts
2.Open Minimal ADB and Fastboot and put the following command
adb reboot edl
OR
Put the phone in fastboot mode, Open Minimal ADB and Fastboot and put the following command
fastboot reboot edl
3.Close Window
4.Open Mi Flash Tool
5.Click "select" button on the upper left and browse to the directory where you extracted your stock rom and click refresh on the right COM port shall appear below
6.Click Flash
7.DONT REMOVE OR DISCONNECT THE USB CABLE FLASHING WILL TAKE SOME TIME
8.After success is shown press the power button for sometime until the phone vibrates first boot will take some time
9.Tada! You are back to stock rom along with your WARRANTY!(If Mi flash doesnt work use QFIL as per given in the steps 1 to 4 given below)
B)If phone doesnt bootup
1. Restart your PC and open QFILClick
2. Select "Flat Build" and "Browse". Now navigate to the extracted ROM/Firmware, and select prog_emmc_firehose_8996_ddr.elf.
3.Select the "load xml" button. This will appear a new explorer. One of them will be needed to navigate to the file
rawprogram0.xml the second one will ask for patch0.xml
4.Turn your phone off. Now press and hold the volume + button, while pressing the power button for 0.5 seconds and plug in the
USB cable in the same moment. If it was successful your phone should appear at QPST/QFIL and you are able to press the
download button. Press the download process and wait to finish.
If it fails, In QFIL Change
"Device Type" to eMMC
"Validation Mode" to 0-No validation
"Reset after Download" no needed to tick (optional)
5.If your phone is not detected in the QFIL or it shows up as port 900E then there are 2 ways to get to 9008 mode
I)
a.Unplug your phone from the computer.
b. Press and hold the POWER button until your phone restarting 3-5 times.
c. After the 3rd times (or more), you will see the notification LED goes off in the middle of boot process, and at that time, quick
press VOLUME + button and release the POWER button but keep the VOLUME + button pressed.
d. Your phone will be at POWER OFF status.
e. After your phone is completely off, press and hold the VOLUME +, then press POWER button and connect your USB at the
same time.
f. Your computer will showing a notification about a new port.
g. If you succeed, you will see Diagnostic Port 9008 at QFIL software
II)
Right click on my computer and select MANAGE, then select Device Manager
See if your device is connected as Diagnostic Port 900E
If it is shown as “QHSUSB_BULK” under Other Device
a. Right-click on QHSUSB_BULK and choose “Update Driver Software“
b. Now click on the Browse button and locate the extracted Qualcomm QDLoader drivers.
c. The installation process shall take place immediately and a system notification will appear. Just choose “Install this driver software anyway“.
d.Click the Close button and check back at Device Manager window. You will now see “Qualcomm HS-USB QDLoader 9008 (COM10)” under Ports (COM & LPT) section.
6. Flash your phone using QFIL software once phone connects in 9008 mode and then reboot.
(Alternatively you can also use the Mi Flash Tool once the phone is in 9008 port)
7.Tada! You have successfully unbricked your phone and regained your WARRANTY!
Update: For saving your user data if your phone gets bricked by bootloader getting locked ONLY follow the below guide
How To-
1. How to switch it off
-firstly this is happening because you have locked you're bootloader
- You have black screen and led on so just hold power button then Zuk logo will be flash after that you will get black screen again and again the phone was preparing to reboot but before that the led will get turn off immediately release power button
- You have it Your phone is switched off
(Let it reboot once after that don't leave the power button and after that led will get off for small time this is the time you have to remove finger from power button this is tricky )
2. Going to Bootloader
-Firstly connect the USB to laptop
-after you have switched off your phone press volume up and down together and with holding buttons connect the phone to USB and you will see the fastboot mode
3. Unlock your phone
-Remember the unlock bootloader file in your email re download it and unlock your bootloader again(no need to redownload if you already have it the file is permanent)
- after unlocking phone you will see phone rebooted press power button reboot press volume the volume button and go to reboot option
- go to fastboot and flash the TWRP and you will see that your data on internal storage is present so flash any ROM and you will see your data
Update: Deep flash using Deep Flash Cable And Procedure to make a deep flash cable
Cut the outer rubber and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
After flashing carefully cover the cut portion by putting the rubber casing first and then covering with electrical tape.
So be careful not to tear anything you just need to precisely cut the covering (around 0.5 cm) in the shape of a ring
Happy Flashing!
Click to expand...
Click to collapse
Okay fine, somebody suggested me to flash stock ROM via qpst method, because I was having battery issues, the flashing process stopped, and I forgot to untick clean all and lock, this left my phone with a screen saying, 'unable to boot'. PC is not detecting my device now, but earlier I unlocked bootloader and flashed tw recovery, but I wasn't able to boot to it, and on qpst, my phone is detected as Diagnostic Port 900E.
AstroBiswas said:
This Procedure Can Also Be Used To Flash Stock Rom And To Regain Warranty
Scenarios-
1.You Somehow relocked your bootloader while on custom rom
2.Your phone flashes the zuk logo and then screen goes blank with led blinking and you cant see the options to go to fastboot or other modes
3.Your Phone Shows port 9008 or 900e while connected to PC
3.You want to regain your warranty
4.You just want to go back to stock rom
This Guide Is for All of the Above Sceneriaos
Following this guide will revert your phone back to stock ROM nougat while deleting your user data and relocking your bootloader
WARNING
If your device is already bricked and if it goes worse than I am not responsible for it. Do at your own risk.
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
B)QPST ROM
1.Indian Version Nougat http://www.mediafire.com/file/f86cs...SER_Q01080.2_N_ZUI_2.5.104_ST_170418_QPST.zip
2.Chinese Version Nougat
http://s.bs.zui.com/DGDc
Extract these rom to preferably a new folder in the root of c drive
STEPS
INSTALL ALL TOOLS AND DRIVERS GIVEN ABOVE
A)If phone is running fine
1.Enable USB Debugging on your Device and give permission to any prompts
2.Open Minimal ADB and Fastboot and put the following command
adb reboot edl
OR
Put the phone in fastboot mode, Open Minimal ADB and Fastboot and put the following command
fastboot reboot edl
3.Close Window
4.Open Mi Flash Tool
5.Click "select" button on the upper left and browse to the directory where you extracted your stock rom and click refresh on the right COM port shall appear below
6.Click Flash
7.DONT REMOVE OR DISCONNECT THE USB CABLE FLASHING WILL TAKE SOME TIME
8.After success is shown press the power button for sometime until the phone vibrates first boot will take some time
9.Tada! You are back to stock rom along with your WARRANTY!(If Mi flash doesnt work use QFIL as per given in the steps 1 to 4 given below)
B)If phone doesnt bootup
1. Restart your PC and open QFILClick
2. Select "Flat Build" and "Browse". Now navigate to the extracted ROM/Firmware, and select prog_emmc_firehose_8996_ddr.elf.
3.Select the "load xml" button. This will appear a new explorer. One of them will be needed to navigate to the file
rawprogram0.xml the second one will ask for patch0.xml
4.Turn your phone off. Now press and hold the volume + button, while pressing the power button for 0.5 seconds and plug in the
USB cable in the same moment. If it was successful your phone should appear at QPST/QFIL and you are able to press the
download button. Press the download process and wait to finish.
If it fails, In QFIL Change
"Device Type" to eMMC
"Validation Mode" to 0-No validation
"Reset after Download" no needed to tick (optional)
5.If your phone is not detected in the QFIL or it shows up as port 900E then there are 2 ways to get to 9008 mode
I)
a.Unplug your phone from the computer.
b. Press and hold the POWER button until your phone restarting 3-5 times.
c. After the 3rd times (or more), you will see the notification LED goes off in the middle of boot process, and at that time, quick
press VOLUME + button and release the POWER button but keep the VOLUME + button pressed.
d. Your phone will be at POWER OFF status.
e. After your phone is completely off, press and hold the VOLUME +, then press POWER button and connect your USB at the
same time.
f. Your computer will showing a notification about a new port.
g. If you succeed, you will see Diagnostic Port 9008 at QFIL software
II)
Right click on my computer and select MANAGE, then select Device Manager
See if your device is connected as Diagnostic Port 900E
If it is shown as “QHSUSB_BULK” under Other Device
a. Right-click on QHSUSB_BULK and choose “Update Driver Software“
b. Now click on the Browse button and locate the extracted Qualcomm QDLoader drivers.
c. The installation process shall take place immediately and a system notification will appear. Just choose “Install this driver software anyway“.
d.Click the Close button and check back at Device Manager window. You will now see “Qualcomm HS-USB QDLoader 9008 (COM10)” under Ports (COM & LPT) section.
6. Flash your phone using QFIL software once phone connects in 9008 mode and then reboot.
(Alternatively you can also use the Mi Flash Tool once the phone is in 9008 port)
7.Tada! You have successfully unbricked your phone and regained your WARRANTY!
Update: For saving your user data if your phone gets bricked by bootloader getting locked ONLY follow the below guide
How To-
1. How to switch it off
-firstly this is happening because you have locked you're bootloader
- You have black screen and led on so just hold power button then Zuk logo will be flash after that you will get black screen again and again the phone was preparing to reboot but before that the led will get turn off immediately release power button
- You have it Your phone is switched off
(Let it reboot once after that don't leave the power button and after that led will get off for small time this is the time you have to remove finger from power button this is tricky )
2. Going to Bootloader
-Firstly connect the USB to laptop
-after you have switched off your phone press volume up and down together and with holding buttons connect the phone to USB and you will see the fastboot mode
3. Unlock your phone
-Remember the unlock bootloader file in your email re download it and unlock your bootloader again(no need to redownload if you already have it the file is permanent)
- after unlocking phone you will see phone rebooted press power button reboot press volume the volume button and go to reboot option
- go to fastboot and flash the TWRP and you will see that your data on internal storage is present so flash any ROM and you will see your data
Update: Deep flash using Deep Flash Cable And Procedure to make a deep flash cable
Cut the outer rubber and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
After flashing carefully cover the cut portion by putting the rubber casing first and then covering with electrical tape.
So be careful not to tear anything you just need to precisely cut the covering (around 0.5 cm) in the shape of a ring
Happy Flashing!
Click to expand...
Click to collapse
What if the phone even won't boot tofastboot mode?? It only vibrates every 10 sec or maybe, will EDL cable work??
Can anybody help
sagarsk said:
Not even coming up as 900E
My hard brick z2 is not even coming up as 900E. Basically computer doesn't detect and no changes in device manager either. Please confirm what to do.
I have tried pressing buttons told by many others and in various other forums. It doesn't work. Does deep flash cable method work even if the phone is not detecting in 900E mode?
Click to expand...
Click to collapse
I also have the same question and I am in the same situation