Database Users

Help!! My L7 is not working,black screen, no charges, QHSUSB_DLOAD what to do?

So I have bought a L7 and when I have it the phone is not working, the seller doesnt want to take my money back so I need help with this :S!
No appears to do anything when connected to charger
No led
No vibrates
No emergency mode
When I connect it to my PC it recognizes it as QHSUSB_DLOAD, but neither KDZ or LG update program recognize it :S!!
Someone know how to reinstall OS I think is software issue but I dont know how fix it
Thanks!

Try following the instruction I got from a website.
What is 'qhsusb_dolad' ?It is the situation when you can't boot into your phone,recovery mode and any other visible interface. When you connected your phone to the PC, the LED will flash and your PC will show that they were searching for the drivers needed(win7/8) but they couldn't find .......If it is commom for you to remove the battery when the phone did not shutdown completely or when you ran into 'No-Response' , as time goes by ,it will be inevitable that you come across the 'QHSUSB_DLOAD' situation .
But from now on ,you needn't worry about that for I have found a way out.
Tools needed:
Hardware: A PC running XP and higher (win7/8 recommended) and your usb cable
Software : MIflash and MIAssistent and a certain mi update rom(It is a *.exe file---fastboot file)
Steps :
1. Install the first two softwares described above(Run as administrator) in your PC (You need to disable the enforcement of digital signature while on win8 in the advanced startup (press 7 or F7)
2.Boot into fastboot mode(you just need to do with your two buttons and usually you cann't see the interface for your screen just won't show in this situation) before connecting to PC
3.Connect you MI2/S to your PC via the usb cable and the pc will recongnise it in the device manager panel(if not, update its driver in the unknown device---qhsusb_dload)
4.Open the miflash and click fresh to load your phone's serial number
5.Flash the update rom(the self-extracted-to folder) into your phone and reboot .
Explanations:
Miassistant contains the 'qhsusb_dload' driver for any phone and it enables the PC(Miflash) to recongnise your CPU serial which is the key part of updating by wire.
Tips:
Try this with your other phone, I believe it will work ,too.
I'm supposed to just copy/paste the link.. but the protocol won't let me since I still don't have more than 10 posts. I just want to help. Try this

Bricked Elife E7, Human Interface Device (HID) Detection Help

Hi Everyone, In an attempt to fix my bricked device with all necessary flash files and drivers installed perfectly, my device is being detected under 'HUMAN INTERFACE DEVICE' as a 'USB INPUT DEVICE' in device manager, according to what i read, my device is suppose to display or be detected as "qulacom HS-USB qloader 9008" under com port. but that isn't happening, i repaired the drivers, re-installed them, formatted my pc and tried it on fresh windows installation. but still the problem is there. i even tried it on several computers but it still detects as USB INPUT DEVICE under Human Interface Devices in device manager. Now i am stuck here with my device dead for the past two weeks. please any one with an idea how to fix this issue?
i will be deeply grateful. Thanks!!
:crying:

Steps Parku said:
Hi Everyone, In an attempt to fix my bricked device with all necessary flash files and drivers installed perfectly, my device is being detected under 'HUMAN INTERFACE DEVICE' as a 'USB INPUT DEVICE' in device manager, according to what i read, my device is suppose to display or be detected as "qulacom HS-USB qloader 9008" under com port. but that isn't happening, i repaired the drivers, re-installed them, formatted my pc and tried it on fresh windows installation. but still the problem is there. i even tried it on several computers but it still detects as USB INPUT DEVICE under Human Interface Devices in device manager. Now i am stuck here with my device dead for the past two weeks. please any one with an idea how to fix this issue?
i will be deeply grateful. Thanks!!
:crying:
Click to expand...
Click to collapse
follow this
1. join in recovery mode (cwm)
2. go mounts and stroge and format system
3 reboot ur device ( Now the loop is eliminated, just a static imagen )
3. dowload drives, firmware , and QNCG
4. install drivers or repair it
5 when the step 4 is done, plug ur device on elife logo and wait for driver installation(like 10 min)
6 use winrar for descompress the firmware
7open GNQC select bp browser, and search in folder firmware a file called BP_imagen
8 try with genereal mode or emergency mode, and click dowload
i did it, its working
u must have patience dont worry
try it, its working
good luck

Still Not Helpful.
andresplata94 said:
follow this
1. join in recovery mode (cwm)
2. go mounts and stroge and format system
3 reboot ur device ( Now the loop is eliminated, just a static imagen )
3. dowload drives, firmware , and QNCG
4. install drivers or repair it
5 when the step 4 is done, plug ur device on elife logo and wait for driver installation(like 10 min)
6 use winrar for descompress the firmware
7open GNQC select bp browser, and search in folder firmware a file called BP_imagen
8 try with genereal mode or emergency mode, and click dowload
i did it, its working
u must have patience dont worry
try it, its working
good luck
Click to expand...
Click to collapse
Actually my device doesn't even come on for me to do all that you said, i tried repairing drivers and all that but it still detects as USB INPUT DEVICE under HUMAN INTERFACE DEVICES. i need my device to detect as qualcomm device before GNQC downloader can detect it. my issue is very different here. because GNQC can't see my device since my device is not being detected the rightful way after all. i will deeply appreciate the solution. Thanks

did u fix it??

U can fix ? I have the same problem since three weeks and nothing... this a a sh*t... only recognized by HID... In other ocassion before of this, i can flash my Gionee but now i cant:crying:

Another one here who saw how the phone bricked after being flashed with GnQc, now when I plug the Usb on the Pc or with wall charger, the red light keep lit and it seems like it will like this forever. I am thinking of trying to get out the screen and disconnect the battery, seems like the phone is stuck on some strange mode.
Thanks.

This feel that not have solution....

Can any one fix it ?

i also got stuck . have given to gionee care they are unable to figure what was the actuall problem

Steps Parku said:
Actually my device doesn't even come on for me to do all that you said, i tried repairing drivers and all that but it still detects as USB INPUT DEVICE under HUMAN INTERFACE DEVICES. i need my device to detect as qualcomm device before GNQC downloader can detect it. my issue is very different here. because GNQC can't see my device since my device is not being detected the rightful way after all. i will deeply appreciate the solution. Thanks
Click to expand...
Click to collapse
the problem for me is that it have recovery stock english(e3) and i can't do anything...
anyone fixed the problem? i have my gionee bricked....

All In One Lenovo Zuk Z2 Plus Hard Brick Recovery Guide and Deep Flash Cable Making P

This Procedure Can Also Be Used To Flash Stock Rom And To Regain Warranty
Scenarios-
1.You Somehow relocked your bootloader while on custom rom
2.Your phone flashes the zuk logo and then screen goes blank with led blinking and you cant see the options to go to fastboot or other modes
3.Your Phone Shows port 9008 or 900e while connected to PC
3.You want to regain your warranty
4.You just want to go back to stock rom
This Guide Is for All of the Above Sceneriaos
Following this guide will revert your phone back to stock ROM nougat while deleting your user data and relocking your bootloader
WARNING
If your device is already bricked and if it goes worse than I am not responsible for it. Do at your own risk.
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
B)QPST ROM
1.Indian Version Nougat http://www.mediafire.com/file/f86cs...SER_Q01080.2_N_ZUI_2.5.104_ST_170418_QPST.zip
2.Chinese Version Nougat
http://s.bs.zui.com/DGDc
Extract these rom to preferably a new folder in the root of c drive
STEPS
INSTALL ALL TOOLS AND DRIVERS GIVEN ABOVE
A)If phone is running fine
1.Enable USB Debugging on your Device and give permission to any prompts
2.Open Minimal ADB and Fastboot and put the following command
adb reboot edl
OR
Put the phone in fastboot mode, Open Minimal ADB and Fastboot and put the following command
fastboot reboot edl
3.Close Window
4.Open Mi Flash Tool
5.Click "select" button on the upper left and browse to the directory where you extracted your stock rom and click refresh on the right COM port shall appear below
6.Click Flash
7.DONT REMOVE OR DISCONNECT THE USB CABLE FLASHING WILL TAKE SOME TIME
8.After success is shown press the power button for sometime until the phone vibrates first boot will take some time
9.Tada! You are back to stock rom along with your WARRANTY!(If Mi flash doesnt work use QFIL as per given in the steps 1 to 4 given below)
B)If phone doesnt bootup
1. Restart your PC and open QFILClick
2. Select "Flat Build" and "Browse". Now navigate to the extracted ROM/Firmware, and select prog_emmc_firehose_8996_ddr.elf.
3.Select the "load xml" button. This will appear a new explorer. One of them will be needed to navigate to the file
rawprogram0.xml the second one will ask for patch0.xml
4.Turn your phone off. Now press and hold the volume + button, while pressing the power button for 0.5 seconds and plug in the
USB cable in the same moment. If it was successful your phone should appear at QPST/QFIL and you are able to press the
download button. Press the download process and wait to finish.
If it fails, In QFIL Change
"Device Type" to eMMC
"Validation Mode" to 0-No validation
"Reset after Download" no needed to tick (optional)
5.If your phone is not detected in the QFIL or it shows up as port 900E then there are 2 ways to get to 9008 mode
I)
a.Unplug your phone from the computer.
b. Press and hold the POWER button until your phone restarting 3-5 times.
c. After the 3rd times (or more), you will see the notification LED goes off in the middle of boot process, and at that time, quick
press VOLUME + button and release the POWER button but keep the VOLUME + button pressed.
d. Your phone will be at POWER OFF status.
e. After your phone is completely off, press and hold the VOLUME +, then press POWER button and connect your USB at the
same time.
f. Your computer will showing a notification about a new port.
g. If you succeed, you will see Diagnostic Port 9008 at QFIL software
II)
Right click on my computer and select MANAGE, then select Device Manager
See if your device is connected as Diagnostic Port 900E
If it is shown as “QHSUSB_BULK” under Other Device
a. Right-click on QHSUSB_BULK and choose “Update Driver Software“
b. Now click on the Browse button and locate the extracted Qualcomm QDLoader drivers.
c. The installation process shall take place immediately and a system notification will appear. Just choose “Install this driver software anyway“.
d.Click the Close button and check back at Device Manager window. You will now see “Qualcomm HS-USB QDLoader 9008 (COM10)” under Ports (COM & LPT) section.
6. Flash your phone using QFIL software once phone connects in 9008 mode and then reboot.
(Alternatively you can also use the Mi Flash Tool once the phone is in 9008 port)
7.Tada! You have successfully unbricked your phone and regained your WARRANTY!
Update: For saving your user data if your phone gets bricked by bootloader getting locked ONLY follow the below guide
How To-
1. How to switch it off
-firstly this is happening because you have locked you're bootloader
- You have black screen and led on so just hold power button then Zuk logo will be flash after that you will get black screen again and again the phone was preparing to reboot but before that the led will get turn off immediately release power button
- You have it Your phone is switched off
(Let it reboot once after that don't leave the power button and after that led will get off for small time this is the time you have to remove finger from power button this is tricky )
2. Going to Bootloader
-Firstly connect the USB to laptop
-after you have switched off your phone press volume up and down together and with holding buttons connect the phone to USB and you will see the fastboot mode
3. Unlock your phone
-Remember the unlock bootloader file in your email re download it and unlock your bootloader again(no need to redownload if you already have it the file is permanent)
- after unlocking phone you will see phone rebooted press power button reboot press volume the volume button and go to reboot option
- go to fastboot and flash the TWRP and you will see that your data on internal storage is present so flash any ROM and you will see your data
Update: Deep flash using Deep Flash Cable And Procedure to make a deep flash cable
Cut the outer rubber and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
After flashing carefully cover the cut portion by putting the rubber casing first and then covering with electrical tape.
So be careful not to tear anything you just need to precisely cut the covering (around 0.5 cm) in the shape of a ring
Happy Flashing!

I think someone has made this guide already.

I see.
well i have a similar issue that i am stuck at 9008 port that is edl but, i can flash rom via Qfil and Mi Flash toll but i cant boot onto it=
I cant get out of edl mode lol. stuck at it.

I deleted some files from qpst rom for intentionally hard bricking my phone and heres another fix.
Cut the outer plastic and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
Happy Flashing!

AstroBiswas said:
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994 - not last edition, latest is v1.0.8
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270 - not last edition, latest is 2.7.460 (fix "sahara" error)
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download - not needed
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790 - not needed (if you use the previous paragraph).
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
Click to expand...
Click to collapse
@AstroBiswas Read red comment.
Not_James_Bond said:
I think someone has made this guide already.
Click to expand...
Click to collapse
Of course!
https://forum.xda-developers.com/le...-to-recover-hard-bricked-zuk-z2-plus-t3576007

Not even coming up as 900E
AstroBiswas said:
This Procedure Can Also Be Used To Flash Stock Rom And To Regain Warranty
Scenarios-
1.You Somehow relocked your bootloader while on custom rom
2.Your phone flashes the zuk logo and then screen goes blank with led blinking and you cant see the options to go to fastboot or other modes
3.Your Phone Shows port 9008 or 900e while connected to PC
3.You want to regain your warranty
4.You just want to go back to stock rom
This Guide Is for All of the Above Sceneriaos
Following this guide will revert your phone back to stock ROM nougat while deleting your user data and relocking your bootloader
WARNING
If your device is already bricked and if it goes worse than I am not responsible for it. Do at your own risk.
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
B)QPST ROM
1.Indian Version Nougat http://www.mediafire.com/file/f86cs...SER_Q01080.2_N_ZUI_2.5.104_ST_170418_QPST.zip
2.Chinese Version Nougat
http://s.bs.zui.com/DGDc
Extract these rom to preferably a new folder in the root of c drive
STEPS
INSTALL ALL TOOLS AND DRIVERS GIVEN ABOVE
A)If phone is running fine
1.Enable USB Debugging on your Device and give permission to any prompts
2.Open Minimal ADB and Fastboot and put the following command
adb reboot edl
OR
Put the phone in fastboot mode, Open Minimal ADB and Fastboot and put the following command
fastboot reboot edl
3.Close Window
4.Open Mi Flash Tool
5.Click "select" button on the upper left and browse to the directory where you extracted your stock rom and click refresh on the right COM port shall appear below
6.Click Flash
7.DONT REMOVE OR DISCONNECT THE USB CABLE FLASHING WILL TAKE SOME TIME
8.After success is shown press the power button for sometime until the phone vibrates first boot will take some time
9.Tada! You are back to stock rom along with your WARRANTY!(If Mi flash doesnt work use QFIL as per given in the steps 1 to 4 given below)
B)If phone doesnt bootup
1. Restart your PC and open QFILClick
2. Select "Flat Build" and "Browse". Now navigate to the extracted ROM/Firmware, and select prog_emmc_firehose_8996_ddr.elf.
3.Select the "load xml" button. This will appear a new explorer. One of them will be needed to navigate to the file
rawprogram0.xml the second one will ask for patch0.xml
4.Turn your phone off. Now press and hold the volume + button, while pressing the power button for 0.5 seconds and plug in the
USB cable in the same moment. If it was successful your phone should appear at QPST/QFIL and you are able to press the
download button. Press the download process and wait to finish.
If it fails, In QFIL Change
"Device Type" to eMMC
"Validation Mode" to 0-No validation
"Reset after Download" no needed to tick (optional)
5.If your phone is not detected in the QFIL or it shows up as port 900E then there are 2 ways to get to 9008 mode
I)
a.Unplug your phone from the computer.
b. Press and hold the POWER button until your phone restarting 3-5 times.
c. After the 3rd times (or more), you will see the notification LED goes off in the middle of boot process, and at that time, quick
press VOLUME + button and release the POWER button but keep the VOLUME + button pressed.
d. Your phone will be at POWER OFF status.
e. After your phone is completely off, press and hold the VOLUME +, then press POWER button and connect your USB at the
same time.
f. Your computer will showing a notification about a new port.
g. If you succeed, you will see Diagnostic Port 9008 at QFIL software
II)
Right click on my computer and select MANAGE, then select Device Manager
See if your device is connected as Diagnostic Port 900E
If it is shown as “QHSUSB_BULK” under Other Device
a. Right-click on QHSUSB_BULK and choose “Update Driver Software“
b. Now click on the Browse button and locate the extracted Qualcomm QDLoader drivers.
c. The installation process shall take place immediately and a system notification will appear. Just choose “Install this driver software anyway“.
d.Click the Close button and check back at Device Manager window. You will now see “Qualcomm HS-USB QDLoader 9008 (COM10)” under Ports (COM & LPT) section.
6. Flash your phone using QFIL software once phone connects in 9008 mode and then reboot.
(Alternatively you can also use the Mi Flash Tool once the phone is in 9008 port)
7.Tada! You have successfully unbricked your phone and regained your WARRANTY!
Update: For saving your user data if your phone gets bricked by bootloader getting locked ONLY follow the below guide
How To-
1. How to switch it off
-firstly this is happening because you have locked you're bootloader
- You have black screen and led on so just hold power button then Zuk logo will be flash after that you will get black screen again and again the phone was preparing to reboot but before that the led will get turn off immediately release power button
- You have it Your phone is switched off
(Let it reboot once after that don't leave the power button and after that led will get off for small time this is the time you have to remove finger from power button this is tricky )
2. Going to Bootloader
-Firstly connect the USB to laptop
-after you have switched off your phone press volume up and down together and with holding buttons connect the phone to USB and you will see the fastboot mode
3. Unlock your phone
-Remember the unlock bootloader file in your email re download it and unlock your bootloader again(no need to redownload if you already have it the file is permanent)
- after unlocking phone you will see phone rebooted press power button reboot press volume the volume button and go to reboot option
- go to fastboot and flash the TWRP and you will see that your data on internal storage is present so flash any ROM and you will see your data
Update: Deep flash using Deep Flash Cable And Procedure to make a deep flash cable
Cut the outer rubber and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
After flashing carefully cover the cut portion by putting the rubber casing first and then covering with electrical tape.
So be careful not to tear anything you just need to precisely cut the covering (around 0.5 cm) in the shape of a ring
Happy Flashing!
Click to expand...
Click to collapse
My hard brick z2 is not even coming up as 900E. Basically computer doesn't detect and no changes in device manager either. Please confirm what to do.
I have tried pressing buttons told by many others and in various other forums. It doesn't work. Does deep flash cable method work even if the phone is not detecting in 900E mode?

You have to boot in proper edl mode...for edl mode hold volume up button 15 second and immediately click power button for .5 sec and attach data cable to phone which is connected to pc and & immediately prees again power button. all while procees alway hold volume up button....

Zuk Z2 Pro Stuck in EDL HS-USB 9008 Port and automatically connecting and disconnect
Hi,
My Zuk Z2 Pro is stuck in EDL 9008 Port. Phone is totally bricked and no sound, no light, no vibration. When i connect with the computer, phone is connecting on HS USB 9008 port and get disconnected after 20-22 seconds and again automatically connected with in half second time.
I am facing this issue after flashing a ZUI 1.9 by using a QPAST/QFIL application. I think i have made stupid mistake by flashing a phone with "ERASE ALL BEFORE DOWNLOAD" option.
I have tried every scenario to get stable this 9008 port but no luck. Since last 5 days i am studying forums and applying every kind of solution but same result.
I am writing this post with high expectations and hope someone will take notice and help me to get rid of this problem.
I can pay through paypal if someone wants to provide professional services to resolve this matter
I will appreciate if someone have any idea and can help me. Thanks

Can someine please help me with this weird situation? Device got disconnected while flashing via qfil. Now no zuk logo nothing. Phone vibrates every 30 sec that's it. Wont even gets recognized by my laptop(no 9008 or 900e port!)

SilenT__ShadoW said:
Can someine please help me with this weird situation? Device got disconnected while flashing via qfil. Now no zuk logo nothing. Phone vibrates every 30 sec that's it. Wont even gets recognized by my laptop(no 9008 or 900e port!)
Click to expand...
Click to collapse
You need to use the deep flash guide which involved cutting and sorting the cable , procedure given in last part of OP

AstroBiswas said:
You need to use the deep flash guide which involved cutting and sorting the cable , procedure given in last part of OP
Click to expand...
Click to collapse
I've tired that also. Connecting phone to pc while green and black wires attached together and detaching them after 5 sec. That also did nothing. However i connect my phone to my pc it just vibrates and blinks led every 30 sec till i remove battery!

SilenT__ShadoW said:
I've tired that also. Connecting phone to pc while green and black wires attached together and detaching them after 5 sec. That also did nothing. However i connect my phone to my pc it just vibrates and blinks led every 30 sec till i remove battery!
Click to expand...
Click to collapse
You need to completely poweoff the phone (difficult in hard brick actually) before this procedure i have forgotten the way to do it, was given on zuk.eu i think, dont worry it may take time but these days hard bricks is repairable too.

AstroBiswas said:
You need to completely poweoff the phone (difficult in hard brick actually) before this procedure i have forgotten the way to do it, was given on zuk.eu i think, dont worry it may take time but these days hard bricks is repairable too.
Click to expand...
Click to collapse
Isn't removing battery connection means powering off the device???

SilenT__ShadoW said:
Isn't removing battery connection means powering off the device???
Click to expand...
Click to collapse
Yes!

AstroBiswas said:
Yes!
Click to expand...
Click to collapse
I'm doing the same.... Removing battery connection every time to switch off.

SilenT__ShadoW said:
I'm doing the same.... Removing battery connection every time to switch off.
Click to expand...
Click to collapse
Thats strange keep trying, perfect timing matters

AstroBiswas said:
Thats strange keep trying, perfect timing matters
Click to expand...
Click to collapse
What do you mean by perfect timing?!?
Never mind. Got my laptop to recognise it and flashed successfully.
Don't know what made it to change its mind!?
What happened?
- was trying to flash and cable got disconnected by accident.
- my phone started to vibrate and blink at the same time for every 30 sec(no zuk logo nothing) and can't seems to be stopped.
- laptop doesn't seems to recognise when device gets connected (no 900e or 9008 port shows up at device manager)
What I did?
- Reinstalled my windows (no problem for me as I only keep system files on partition c)
- Disabled driver verification (windows 10 thing)
- Installed zuk driver, adb , mi tools inside partition c(all inside a folder called zuk)
- used cable that came with phone instead of 3rd party to deep flash

AstroBiswas said:
This Procedure Can Also Be Used To Flash Stock Rom And To Regain Warranty
Scenarios-
1.You Somehow relocked your bootloader while on custom rom
2.Your phone flashes the zuk logo and then screen goes blank with led blinking and you cant see the options to go to fastboot or other modes
3.Your Phone Shows port 9008 or 900e while connected to PC
3.You want to regain your warranty
4.You just want to go back to stock rom
This Guide Is for All of the Above Sceneriaos
Following this guide will revert your phone back to stock ROM nougat while deleting your user data and relocking your bootloader
WARNING
If your device is already bricked and if it goes worse than I am not responsible for it. Do at your own risk.
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
B)QPST ROM
1.Indian Version Nougat http://www.mediafire.com/file/f86cs...SER_Q01080.2_N_ZUI_2.5.104_ST_170418_QPST.zip
2.Chinese Version Nougat
http://s.bs.zui.com/DGDc
Extract these rom to preferably a new folder in the root of c drive
STEPS
INSTALL ALL TOOLS AND DRIVERS GIVEN ABOVE
A)If phone is running fine
1.Enable USB Debugging on your Device and give permission to any prompts
2.Open Minimal ADB and Fastboot and put the following command
adb reboot edl
OR
Put the phone in fastboot mode, Open Minimal ADB and Fastboot and put the following command
fastboot reboot edl
3.Close Window
4.Open Mi Flash Tool
5.Click "select" button on the upper left and browse to the directory where you extracted your stock rom and click refresh on the right COM port shall appear below
6.Click Flash
7.DONT REMOVE OR DISCONNECT THE USB CABLE FLASHING WILL TAKE SOME TIME
8.After success is shown press the power button for sometime until the phone vibrates first boot will take some time
9.Tada! You are back to stock rom along with your WARRANTY!(If Mi flash doesnt work use QFIL as per given in the steps 1 to 4 given below)
B)If phone doesnt bootup
1. Restart your PC and open QFILClick
2. Select "Flat Build" and "Browse". Now navigate to the extracted ROM/Firmware, and select prog_emmc_firehose_8996_ddr.elf.
3.Select the "load xml" button. This will appear a new explorer. One of them will be needed to navigate to the file
rawprogram0.xml the second one will ask for patch0.xml
4.Turn your phone off. Now press and hold the volume + button, while pressing the power button for 0.5 seconds and plug in the
USB cable in the same moment. If it was successful your phone should appear at QPST/QFIL and you are able to press the
download button. Press the download process and wait to finish.
If it fails, In QFIL Change
"Device Type" to eMMC
"Validation Mode" to 0-No validation
"Reset after Download" no needed to tick (optional)
5.If your phone is not detected in the QFIL or it shows up as port 900E then there are 2 ways to get to 9008 mode
I)
a.Unplug your phone from the computer.
b. Press and hold the POWER button until your phone restarting 3-5 times.
c. After the 3rd times (or more), you will see the notification LED goes off in the middle of boot process, and at that time, quick
press VOLUME + button and release the POWER button but keep the VOLUME + button pressed.
d. Your phone will be at POWER OFF status.
e. After your phone is completely off, press and hold the VOLUME +, then press POWER button and connect your USB at the
same time.
f. Your computer will showing a notification about a new port.
g. If you succeed, you will see Diagnostic Port 9008 at QFIL software
II)
Right click on my computer and select MANAGE, then select Device Manager
See if your device is connected as Diagnostic Port 900E
If it is shown as “QHSUSB_BULK” under Other Device
a. Right-click on QHSUSB_BULK and choose “Update Driver Software“
b. Now click on the Browse button and locate the extracted Qualcomm QDLoader drivers.
c. The installation process shall take place immediately and a system notification will appear. Just choose “Install this driver software anyway“.
d.Click the Close button and check back at Device Manager window. You will now see “Qualcomm HS-USB QDLoader 9008 (COM10)” under Ports (COM & LPT) section.
6. Flash your phone using QFIL software once phone connects in 9008 mode and then reboot.
(Alternatively you can also use the Mi Flash Tool once the phone is in 9008 port)
7.Tada! You have successfully unbricked your phone and regained your WARRANTY!
Update: For saving your user data if your phone gets bricked by bootloader getting locked ONLY follow the below guide
How To-
1. How to switch it off
-firstly this is happening because you have locked you're bootloader
- You have black screen and led on so just hold power button then Zuk logo will be flash after that you will get black screen again and again the phone was preparing to reboot but before that the led will get turn off immediately release power button
- You have it Your phone is switched off
(Let it reboot once after that don't leave the power button and after that led will get off for small time this is the time you have to remove finger from power button this is tricky )
2. Going to Bootloader
-Firstly connect the USB to laptop
-after you have switched off your phone press volume up and down together and with holding buttons connect the phone to USB and you will see the fastboot mode
3. Unlock your phone
-Remember the unlock bootloader file in your email re download it and unlock your bootloader again(no need to redownload if you already have it the file is permanent)
- after unlocking phone you will see phone rebooted press power button reboot press volume the volume button and go to reboot option
- go to fastboot and flash the TWRP and you will see that your data on internal storage is present so flash any ROM and you will see your data
Update: Deep flash using Deep Flash Cable And Procedure to make a deep flash cable
Cut the outer rubber and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
After flashing carefully cover the cut portion by putting the rubber casing first and then covering with electrical tape.
So be careful not to tear anything you just need to precisely cut the covering (around 0.5 cm) in the shape of a ring
Happy Flashing!
Click to expand...
Click to collapse
Okay fine, somebody suggested me to flash stock ROM via qpst method, because I was having battery issues, the flashing process stopped, and I forgot to untick clean all and lock, this left my phone with a screen saying, 'unable to boot'. PC is not detecting my device now, but earlier I unlocked bootloader and flashed tw recovery, but I wasn't able to boot to it, and on qpst, my phone is detected as Diagnostic Port 900E.

AstroBiswas said:
This Procedure Can Also Be Used To Flash Stock Rom And To Regain Warranty
Scenarios-
1.You Somehow relocked your bootloader while on custom rom
2.Your phone flashes the zuk logo and then screen goes blank with led blinking and you cant see the options to go to fastboot or other modes
3.Your Phone Shows port 9008 or 900e while connected to PC
3.You want to regain your warranty
4.You just want to go back to stock rom
This Guide Is for All of the Above Sceneriaos
Following this guide will revert your phone back to stock ROM nougat while deleting your user data and relocking your bootloader
WARNING
If your device is already bricked and if it goes worse than I am not responsible for it. Do at your own risk.
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
B)QPST ROM
1.Indian Version Nougat http://www.mediafire.com/file/f86cs...SER_Q01080.2_N_ZUI_2.5.104_ST_170418_QPST.zip
2.Chinese Version Nougat
http://s.bs.zui.com/DGDc
Extract these rom to preferably a new folder in the root of c drive
STEPS
INSTALL ALL TOOLS AND DRIVERS GIVEN ABOVE
A)If phone is running fine
1.Enable USB Debugging on your Device and give permission to any prompts
2.Open Minimal ADB and Fastboot and put the following command
adb reboot edl
OR
Put the phone in fastboot mode, Open Minimal ADB and Fastboot and put the following command
fastboot reboot edl
3.Close Window
4.Open Mi Flash Tool
5.Click "select" button on the upper left and browse to the directory where you extracted your stock rom and click refresh on the right COM port shall appear below
6.Click Flash
7.DONT REMOVE OR DISCONNECT THE USB CABLE FLASHING WILL TAKE SOME TIME
8.After success is shown press the power button for sometime until the phone vibrates first boot will take some time
9.Tada! You are back to stock rom along with your WARRANTY!(If Mi flash doesnt work use QFIL as per given in the steps 1 to 4 given below)
B)If phone doesnt bootup
1. Restart your PC and open QFILClick
2. Select "Flat Build" and "Browse". Now navigate to the extracted ROM/Firmware, and select prog_emmc_firehose_8996_ddr.elf.
3.Select the "load xml" button. This will appear a new explorer. One of them will be needed to navigate to the file
rawprogram0.xml the second one will ask for patch0.xml
4.Turn your phone off. Now press and hold the volume + button, while pressing the power button for 0.5 seconds and plug in the
USB cable in the same moment. If it was successful your phone should appear at QPST/QFIL and you are able to press the
download button. Press the download process and wait to finish.
If it fails, In QFIL Change
"Device Type" to eMMC
"Validation Mode" to 0-No validation
"Reset after Download" no needed to tick (optional)
5.If your phone is not detected in the QFIL or it shows up as port 900E then there are 2 ways to get to 9008 mode
I)
a.Unplug your phone from the computer.
b. Press and hold the POWER button until your phone restarting 3-5 times.
c. After the 3rd times (or more), you will see the notification LED goes off in the middle of boot process, and at that time, quick
press VOLUME + button and release the POWER button but keep the VOLUME + button pressed.
d. Your phone will be at POWER OFF status.
e. After your phone is completely off, press and hold the VOLUME +, then press POWER button and connect your USB at the
same time.
f. Your computer will showing a notification about a new port.
g. If you succeed, you will see Diagnostic Port 9008 at QFIL software
II)
Right click on my computer and select MANAGE, then select Device Manager
See if your device is connected as Diagnostic Port 900E
If it is shown as “QHSUSB_BULK” under Other Device
a. Right-click on QHSUSB_BULK and choose “Update Driver Software“
b. Now click on the Browse button and locate the extracted Qualcomm QDLoader drivers.
c. The installation process shall take place immediately and a system notification will appear. Just choose “Install this driver software anyway“.
d.Click the Close button and check back at Device Manager window. You will now see “Qualcomm HS-USB QDLoader 9008 (COM10)” under Ports (COM & LPT) section.
6. Flash your phone using QFIL software once phone connects in 9008 mode and then reboot.
(Alternatively you can also use the Mi Flash Tool once the phone is in 9008 port)
7.Tada! You have successfully unbricked your phone and regained your WARRANTY!
Update: For saving your user data if your phone gets bricked by bootloader getting locked ONLY follow the below guide
How To-
1. How to switch it off
-firstly this is happening because you have locked you're bootloader
- You have black screen and led on so just hold power button then Zuk logo will be flash after that you will get black screen again and again the phone was preparing to reboot but before that the led will get turn off immediately release power button
- You have it Your phone is switched off
(Let it reboot once after that don't leave the power button and after that led will get off for small time this is the time you have to remove finger from power button this is tricky )
2. Going to Bootloader
-Firstly connect the USB to laptop
-after you have switched off your phone press volume up and down together and with holding buttons connect the phone to USB and you will see the fastboot mode
3. Unlock your phone
-Remember the unlock bootloader file in your email re download it and unlock your bootloader again(no need to redownload if you already have it the file is permanent)
- after unlocking phone you will see phone rebooted press power button reboot press volume the volume button and go to reboot option
- go to fastboot and flash the TWRP and you will see that your data on internal storage is present so flash any ROM and you will see your data
Update: Deep flash using Deep Flash Cable And Procedure to make a deep flash cable
Cut the outer rubber and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
After flashing carefully cover the cut portion by putting the rubber casing first and then covering with electrical tape.
So be careful not to tear anything you just need to precisely cut the covering (around 0.5 cm) in the shape of a ring
Happy Flashing!
Click to expand...
Click to collapse
What if the phone even won't boot tofastboot mode?? It only vibrates every 10 sec or maybe, will EDL cable work??
Can anybody help

sagarsk said:
Not even coming up as 900E
My hard brick z2 is not even coming up as 900E. Basically computer doesn't detect and no changes in device manager either. Please confirm what to do.
I have tried pressing buttons told by many others and in various other forums. It doesn't work. Does deep flash cable method work even if the phone is not detecting in 900E mode?
Click to expand...
Click to collapse
I also have the same question and I am in the same situation

How to enter the 9008 mode

My nokia6 TA-100 couldn't reboot, press the 3 keys about 10's, the light flashes .
Connect to USB ,short the black& green ,only show 900e,couldn't find 9008 .
Help me

blackfaces said:
My nokia6 TA-100 couldn't reboot, press the 3 keys about 10's, the light flashes .
Connect to USB ,short the black& green ,only show 900e,couldn't find 9008 .
Help me
Click to expand...
Click to collapse
Your phone is hard bricked It is not possible to repair it yourself. You must send the phone to the Nokia service. I had exactly the same problem. I was looking for a solution for a long time but I did not find it.
Today I received a repaired phone - under warranty.

repaired phone
jurek09 said:
Your phone is hard bricked It is not possible to repair it yourself. You must send the phone to the Nokia service. I had exactly the same problem. I was looking for a solution for a long time but I did not find it.
Today I received a repaired phone - under warranty.
Click to expand...
Click to collapse
What about a repaired phone? what was the state of the phone, the mine is all black screen with no lights but the pc recognizes it as 9008 port

Maxpowers88 said:
What about a repaired phone? what was the state of the phone, the mine is all black screen with no lights but the pc recognizes it as 9008 port
Click to expand...
Click to collapse
THESE STEPS ARE FOR 9008 PORT, FOLLOW ALL THE STEPS CAREFULLY:
Find the flash file for TA-1000 from here:
https://yadi.sk/d/fN5Oinvt3MwufR
Tool frome here:
https://aiomobilestuff.com/download-all-versions-of-qpst-flash-tool/
Drivers from here:
http://www.mediafire.com/file/j3g88d4e3kd62bs/Qualicom+Driver+V1.1.0.0.rar
Steps to flash the phones
Step1: To use QPST, some drivers need to be installed on your Computer.
Note: While installing driver avoid using cable for successful installation.
When Drivers installed, Attach Phone to PC via USB cable.
While connecting to PC, phone should be switched off and press volume up & down as boot key.
If it Create Qualcomm HS-USB QDLoader 9008 port in device manager , then driver has been successfully installed.
Once driver installation is complete, follow the instructions below to flash the MBN firmware file to your Qualcomm device.
Step 2. Make sure your device is charged to at least 30%.
Step 3. Run QFIL tool.
Step 4. Now Browse under the Programmer path to Chose MBN File.
Step 5. As soon as the MBN file is selected, Select Build will automatically select the Update or Stock ROM.
Step 6. Next Go To Load XML, select rawprogram_unsparse_without_qcn.xml and Select Patch0.xml
Load XML comes with two option:
rawprogram_unsparse_without_qcn.xml : On choosing this file, data will not be lost.
rawprogram_unsparse.xml : Will lose RF Calibration data, IMEI and WiFi/Bluetooth Address.
Step 7. Turn off the Phone and Attach it to PC by pressing Vol up & down button.
Step 8. Click on Select Port and choose the port.
Step 9. Click on Download to start flashing.
Step 10. Disconnect device from USB cable once Finish Download appears.
That’s all!
Hit thanks button if you find this helpful
Happy flashing

sltushar said:
THESE STEPS ARE FOR 9008 PORT, FOLLOW ALL THE STEPS CAREFULLY:
Find the flash file for TA-1000 from here:
https://yadi.sk/d/fN5Oinvt3MwufR
Tool frome here:
https://aiomobilestuff.com/download-all-versions-of-qpst-flash-tool/
Drivers from here:
http://www.mediafire.com/file/j3g88d4e3kd62bs/Qualicom+Driver+V1.1.0.0.rar
Steps to flash the phones
Step1: To use QPST, some drivers need to be installed on your Computer.
Note: While installing driver avoid using cable for successful installation.
When Drivers installed, Attach Phone to PC via USB cable.
While connecting to PC, phone should be switched off and press volume up & down as boot key.
If it Create Qualcomm HS-USB QDLoader 9008 port in device manager , then driver has been successfully installed.
Once driver installation is complete, follow the instructions below to flash the MBN firmware file to your Qualcomm device.
Step 2. Make sure your device is charged to at least 30%.
Step 3. Run QFIL tool.
Step 4. Now Browse under the Programmer path to Chose MBN File.
Step 5. As soon as the MBN file is selected, Select Build will automatically select the Update or Stock ROM.
Step 6. Next Go To Load XML, select rawprogram_unsparse_without_qcn.xml and Select Patch0.xml
Load XML comes with two option:
rawprogram_unsparse_without_qcn.xml : On choosing this file, data will not be lost.
rawprogram_unsparse.xml : Will lose RF Calibration data, IMEI and WiFi/Bluetooth Address.
Step 7. Turn off the Phone and Attach it to PC by pressing Vol up & down button.
Step 8. Click on Select Port and choose the port.
Step 9. Click on Download to start flashing.
Step 10. Disconnect device from USB cable once Finish Download appears.
That’s all!
Hit thanks button if you find this helpful
Happy flashing
Click to expand...
Click to collapse
Yes I tried it but when it starts to flash appears an error like unable to connect Sahara.... and it didn’t flash... any idea about this error?
---------- Post added at 04:24 AM ---------- Previous post was at 04:22 AM ----------
sltushar said:
THESE STEPS ARE FOR 9008 PORT, FOLLOW ALL THE STEPS CAREFULLY:
Find the flash file for TA-1000 from here:
https://yadi.sk/d/fN5Oinvt3MwufR
Tool frome here:
https://aiomobilestuff.com/download-all-versions-of-qpst-flash-tool/
Drivers from here:
http://www.mediafire.com/file/j3g88d4e3kd62bs/Qualicom+Driver+V1.1.0.0.rar
Steps to flash the phones
Step1: To use QPST, some drivers need to be installed on your Computer.
Note: While installing driver avoid using cable for successful installation.
When Drivers installed, Attach Phone to PC via USB cable.
While connecting to PC, phone should be switched off and press volume up & down as boot key.
If it Create Qualcomm HS-USB QDLoader 9008 port in device manager , then driver has been successfully installed.
Once driver installation is complete, follow the instructions below to flash the MBN firmware file to your Qualcomm device.
Step 2. Make sure your device is charged to at least 30%.
Step 3. Run QFIL tool.
Step 4. Now Browse under the Programmer path to Chose MBN File.
Step 5. As soon as the MBN file is selected, Select Build will automatically select the Update or Stock ROM.
Step 6. Next Go To Load XML, select rawprogram_unsparse_without_qcn.xml and Select Patch0.xml
Load XML comes with two option:
rawprogram_unsparse_without_qcn.xml : On choosing this file, data will not be lost.
rawprogram_unsparse.xml : Will lose RF Calibration data, IMEI and WiFi/Bluetooth Address.
Step 7. Turn off the Phone and Attach it to PC by pressing Vol up & down button.
Step 8. Click on Select Port and choose the port.
Step 9. Click on Download to start flashing.
Step 10. Disconnect device from USB cable once Finish Download appears.
That’s all!
Hit thanks button if you find this helpful
Happy flashing
Click to expand...
Click to collapse
Thanks in advice. I really appreciate your comment.
Can I contact you to try this remotely like Skype, WhatsApp, telegram, teamviewer or like that?
Hope you can help me

Maxpowers88 said:
Yes I tried it but when it starts to flash appears an error like unable to connect Sahara.... and it didn’t flash... any idea about this error?
Click to expand...
Click to collapse
Yes surely
Find the portabale tool from attachment
Hit thanks button if you find this helpful
Happy flashing

sltushar said:
Yes surely
Find the portabale tool from attachment
Hit thanks button if you find this helpful
Happy flashing
Click to expand...
Click to collapse
Ok I’m downloading it in this moment. I will be at home in 20 mins to try it. Thanks in advice. I will let you know what as going on.

Maxpowers88 said:
Ok I’m downloading it in this moment. I will be at home in 20 mins to try it. Thanks in advice. I will let you know what as going on.
Click to expand...
Click to collapse
Sure..

Maxpowers88 said:
What about a repaired phone? what was the state of the phone, the mine is all black screen with no lights but the pc recognizes it as 9008 port
Click to expand...
Click to collapse
I have China version (TA-1000). Same as you, I had all black screen. When i connet charger notification led notification LED was shining (for a strange green-red color). My Nokia was detected by PC as Qualcomm HS-USB Diagnostics 900E. I tried on a lot of ways to put it in mode Qualcomm HS-USB QDLoader 9008 but without success.

jurek09 said:
Your phone is hard bricked It is not possible to repair it yourself. You must send the phone to the Nokia service. I had exactly the same problem. I was looking for a solution for a long time but I did not find it.
Today I received a repaired phone - under warranty.
Click to expand...
Click to collapse
OK, Thanks, I try to send it to the to the Nokia service.

Question Nothing Phone 1 hard bricked (Edl Mode)

Hello there members.
i have a Nothing Phone 1 in Edl Mode. Tried to restart it but still connected on Edl. i have searched around for this problem but sill unlucky to find a solution.
Client pretend to have played with roms and flashed the wrong one.
Any help suggestion?

pogradecari said:
Hello there members.
i have a Nothing Phone 1 in Edl Mode. Tried to restart it but still connected on Edl. i have searched around for this problem but sill unlucky to find a solution.
Client pretend to have played with roms and flashed the wrong one.
Any help suggestion?
Click to expand...
Click to collapse
Try holding power+volup+voldown with the phone unplugged from a computer.
If it doesn't work, let me know.

how to boot to edl mode ??

Try this :
Install ADB and Minimal Fastboot drivers through which Windows will recognize your Device.
Enable USB Debugging on your Android Device. You can do this simply by following the given direction:
Settings > About Phone > tap 7 times on the Build Number. This will enable Developer options on it.
Now, again go back to the main Settings > Developer options > USB Debugging and Enable it.
Connect your smartphone with your PC via a USB cable.
Open Command Window by the press and hold Shift Key + right-click of your Mouse.
Choose Open Command Window here.
Type the following command and press the Enter button to check whether the device is connected or not.
" adb devices "
You will see a device serial code on the screen. That means it is successfully connected. Then follow the next step.
Type the command from below and hit enter to Boot into Download Mode (EDL Mode):
" adb reboot edl " or "fastboot oem edl" or "fastboot reboot-edl" or "fastboot reboot edl"

muppetz said:
Try this :
Install ADB and Minimal Fastboot drivers through which Windows will recognize your Device.
Enable USB Debugging on your Android Device. You can do this simply by following the given direction:
Settings > About Phone > tap 7 times on the Build Number. This will enable Developer options on it.
Now, again go back to the main Settings > Developer options > USB Debugging and Enable it.
Connect your smartphone with your PC via a USB cable.
Open Command Window by the press and hold Shift Key + right-click of your Mouse.
Choose Open Command Window here.
Type the following command and press the Enter button to check whether the device is connected or not.
" adb devices "
You will see a device serial code on the screen. That means it is successfully connected. Then follow the next step.
Type the command from below and hit enter to Boot into Download Mode (EDL Mode):
" adb reboot edl "
Click to expand...
Click to collapse
my phone is bricked while flashing stock rom via fastboot
so unable to boot to recovery or bootloader

To begin with, power off your device. If you can’t do so, then you will have to wait until the battery completely drains out.
Now connect one end of the USB cable to your PC, but don’t attach the other end to the device.
Press and hold the Volume Up and Volume Down buttons together for a few seconds.
Now connect the other end of the device to the USB cable.
Your device will now be recognized as Qualcomm HS-USB QDLoader 9008. You may now flash the device-specific firmware to unbrick it.
Even you have a black screen , PC does recognize your phone . Use only a USB 2.0 port . Verify if Qualcomm USB Driver have been installed on Windows .

muppetz said:
To begin with, power off your device. If you can’t do so, then you will have to wait until the battery completely drains out.
Now connect one end of the USB cable to your PC, but don’t attach the other end to the device.
Press and hold the Volume Up and Volume Down buttons together for a few seconds.
Now connect the other end of the device to the USB cable.
Your device will now be recognized as Qualcomm HS-USB QDLoader 9008. You may now flash the device-specific firmware to unbrick it.
Even you have a black screen , PC does recognize your phone . Use only a USB 2.0 port . Verify if drivers have been installed on Windows .
Click to expand...
Click to collapse
tried these steps but phone goes in 900E mode

OK , look then at this :

muppetz said:
OK , look then at this :
Click to expand...
Click to collapse
it does not work as he just changed the drivers from diagnostic mode to qdloader mode

pogradecari said:
Hello there members.
i have a Nothing Phone 1 in Edl Mode. Tried to restart it but still connected on Edl. i have searched around for this problem but sill unlucky to find a solution.
Client pretend to have played with roms and flashed the wrong one.
Any help suggestion?
Click to expand...
Click to collapse
Maybe it's too late already but you can unbrick the phone with this tool
Unbrick / Flash Stock Rom (1.1.7 global) QDLoader 9008 fix | EDL Mode fix
Hi everyone, If your phone (1) does not react on any of yours actions. You may have the same problem. This is an instruction how to fix it without Disassembly. ‼️ Do this at your own risk, I am not responsible for any damage that may occur to...
forum.xda-developers.com

none of these will work

pogradecari said:
none of these will work
Click to expand...
Click to collapse
Why? Have you tried?