Hi everyone!
I think I bricked my phone :crying:
Everytime I try to turn it on I see this on the screen (see pic)
And the worst of all is that my windows laptop doesn't recognize the phone when I connect it via usb, the pc tells me that it's an unknown device and there's an error code 43...
Help me pls!
just press and hold volume up and your phone will restart
cristi.blidariu said:
just press and hold volume up and your phone will restart
Click to expand...
Click to collapse
It's the first thing I did but It didn' work
you must keep press up to 10 sec,i have try this method my self and he work,if is not work,then i suggest you to put i higher version on your sd card and make a force upgrade by press and hold volume button up and down and power button
cristi.blidariu said:
you must keep press up to 10 sec,i have try this method my self and he work,if is not work,then i suggest you to put i higher version on your sd card and make a force upgrade by press and hold volume button up and down and power button
Click to expand...
Click to collapse
I did it but it doesn't work. the phone tells me this everytime:
can you upload a photo with your screen phone were is sow locked?
Fastboot or downloading mode, once your in there you should be able to install a custom recovery if you already did that already go to your computer and find your firmware for your phone online, put it on your sd card and install it from your custom recovery and it should work or a simple factory reset would work IF you DO NOT know what all of this is or how to do it everyone on here should know how to help you
Hostliner said:
Fastboot or downloading mode, once your in there you should be able to install a custom recovery if you already did that already go to your computer and find your firmware for your phone online, put it on your sd card and install it from your custom recovery and it should work or a simple factory reset would work IF you DO NOT know what all of this is or how to do it everyone on here should know how to help you
Click to expand...
Click to collapse
good point
Hostliner said:
Fastboot or downloading mode, once your in there you should be able to install a custom recovery if you already did that already go to your computer and find your firmware for your phone online, put it on your sd card and install it from your custom recovery and it should work or a simple factory reset would work IF you DO NOT know what all of this is or how to do it everyone on here should know how to help you
Click to expand...
Click to collapse
I have the official firmware and everything, I put it all in the sd card and press the up, down and power buttons but it keeps telling me this (see pic) and as I said before my windows laptop doesn't recognize the phone when I connect it via usb, the pc tells me that it's an unknown device and there's an error code 43...
cristi.blidariu said:
can you upload a photo with your screen phone were is sow locked?
Click to expand...
Click to collapse
It doesn't tell me "locked" it only tell my this:
you need to enter in recovery mod and wipe data and cache,keep try by press and hold volume up and power,and you will need to install hi suite on your pc,download this https://mega.nz/#!Pc9zjDYB!X0wTeiFdY-ca70K9tI-b5fYf40LpcVExIEim0Xk9v14 is the adb and fastboot,conect your phone to pc,extract the file an you will find a folder adb,open,press and hold shift and right click,search for open command here it will open a cmd window,now run the command adb reboot bootloader and wait till reboot in to fastboot mod,now run the command fastboot reboot
Download other version of your firmware. Then do a manual installation. An older firmware maybe.
cristi.blidariu said:
you need to enter in recovery mod and wipe data and cache,keep try by press and hold volume up and power,and you will need to install hi suite on your pc,download this https://mega.nz/#!Pc9zjDYB is the adb and fastboot,conect your phone to pc,extract the file an you will find a folder adb,open,press and hold shift and right click,search for open command here it will open a cmd window,now run the command adb reboot bootloader and wait till reboot in to fastboot mod,now run the command fastboot reboot
Click to expand...
Click to collapse
What's the password? the site asks me for a password
HeyAnas98 said:
What's the password? the site asks me for a password
Click to expand...
Click to collapse
try this https://mega.nz/#!Pc9zjDYB!X0wTeiFdY-ca70K9tI-b5fYf40LpcVExIEim0Xk9v14
cristi.blidariu said:
try this https://mega.nz/#!Pc9zjDYB!X0wTeiFdY-ca70K9tI-b5fYf40LpcVExIEim0Xk9v14
Click to expand...
Click to collapse
Okay, I'll try to do what you told me later. Then, I'll tell you if that worked. Thanks!!!
k,good luck
Had the same problem. Try this, switch off the phone and unplug from pc, hold volume down then then plug usb back in whilst holding vol down. Should boot to fastboot mode...if not, you can disconnect phone battery and follow above steps again whilst battery is disconnected.
But sadly the p8 lite didn't have removable battery
I know...which is why I took off the back cover and disconnected the battery from the circuit...
HeyAnas98 said:
Hi everyone!
I think I bricked my phone :crying:
Everytime I try to turn it on I see this on the screen (see pic)
And the worst of all is that my windows laptop doesn't recognize the phone when I connect it via usb, the pc tells me that it's an unknown device and there's an error code 43...
Help me pls!
Click to expand...
Click to collapse
download this version of HiSuite 4.04.301,it has a option of system recovery,all you have to do is to have usb debugging enable and conect your phone to pc via usb cable
Related
Since January i been waiting to root my phone. Htc wildfire 2.2.1
I already tried with unrevoked, and a lots of other ways and never with sucess annd today i have been sucess
I root my wildfire with alpharev to put S-Off and then with SuperOneClickv1.9.5.
Restart and voila.....
Go to hxxp://alpharev.nl/x/beta/ & download the windows version
2. When it asks you for the serial, enter your phone's serial number. Go to Settings > About phone & enter your serial. Copy the code given into notepad
3. Make sure you turn on USB debugging in Settings > Application > Development
4. Install the HTC Driver. Mine is in the memory card that came with the phone
5. Extract & run alpharevx.exe. Use the code given earlier. Then connect your phone. It should detect & your phone should display USB debugging mode
6. Wait for it to complete. Once it is completed, you can remove your phone.
7. To check turn off your phone. Then press volume down & power. On top it should display alpharevx & s-off
Clockwork recovery
1. This is to enable you to install a custom rom, and also for backup
2. Get the fastboot tool for windows
3. Copy the fastboot file you downloaded to the alpharevx folder. Copy the folder to drive C so it is easier to run command prompt. Rename the folder to wildfire
4. Download the recovery for Wildfire. Extract & rename it to wildfire.img
5. Open command prompt. Type cd c:/wildfire & fastboot flash recovery wildfire.img
6. Download & install HBOOT driver from unrevoked. Go into bootloader (volume down & power), select fastboot. Connect your phone & it will display fasboot usb cable
(take this part from web - Author: Joel512)
Next step just need to download and run SuperOneClickv1.9.5 and restart
I don`t known if you people already know. If so I apologize
Sorry for my Inglish
It would be more useful if u can share the video 'how-to' in YouTube I'm yet trying dis coz on Mac rite now.
Damag3 said:
Since January i been waiting to root my phone. Htc wildfire 2.2.1
I already tried with unrevoked, and a lots of other ways and never with sucess annd today i have been sucess
I root my wildfire with alpharev to put S-Off and then with SuperOneClickv1.9.5.
Restart and voila.....
Go to hxxp://alpharev.nl/x/beta/ & download the windows version
2. When it asks you for the serial, enter your phone's serial number. Go to Settings > About phone & enter your serial. Copy the code given into notepad
3. Make sure you turn on USB debugging in Settings > Application > Development
4. Install the HTC Driver. Mine is in the memory card that came with the phone
5. Extract & run alpharevx.exe. Use the code given earlier. Then connect your phone. It should detect & your phone should display USB debugging mode
6. Wait for it to complete. Once it is completed, you can remove your phone.
7. To check turn off your phone. Then press volume down & power. On top it should display alpharevx & s-off
Clockwork recovery
1. This is to enable you to install a custom rom, and also for backup
2. Get the fastboot tool for windows
3. Copy the fastboot file you downloaded to the alpharevx folder. Copy the folder to drive C so it is easier to run command prompt. Rename the folder to wildfire
4. Download the recovery for Wildfire. Extract & rename it to wildfire.img
5. Open command prompt. Type cd c:/wildfire & fastboot flash recovery wildfire.img
6. Download & install HBOOT driver from unrevoked. Go into bootloader (volume down & power), select fastboot. Connect your phone & it will display fasboot usb cable
(take this part from web - Author: Joel512)
Next step just need to download and run SuperOneClickv1.9.5 and restart
I don`t known if you people already know. If so I apologize
Sorry for my Inglish
Click to expand...
Click to collapse
Hey thanks for the SuperOneClickv1.9.5 info!!! I was searching for a one click rooting alternative!!!
imkr said:
It would be more useful if u can share the video 'how-to' in YouTube I'm yet trying dis coz on Mac rite now.
Click to expand...
Click to collapse
What are you trying on Mac.
AlpharevX will not support Mac platform right. Only windows and Linux supported. Easiest is Linux. Live CD is perfect.
Sent from my HTC Wildfire using XDA App
bharatgaddameedi said:
What are you trying on Mac.
AlpharevX will not support Mac platform right. Only windows and Linux supported. Easiest is Linux.
Sent from my HTC Wildfire using XDA App
Click to expand...
Click to collapse
Yes! it doesn't working on Mac
HEy I have successfully turned S-OFF. When I try doing the Clockwork recovery thing it gets struck at waiting for device!! Any advice??
ameya88 said:
HEy I have successfully turned S-OFF. When I try doing the Clockwork recovery thing it gets struck at waiting for device!! Any advice??
Click to expand...
Click to collapse
uninstall htc sync if you have it installed.
Its uninstalled, thats the first thing I did to avoid any complications!!
Now what do I do???? I waited for around 20 mins but its not going ahead!!
try this way http://forum.xda-developers.com/showthread.php?t=1130044
The guide referenced in the link above sure worked for me
Just a word of advice, the linux version of alpharevX gets stuck on 'waiting for device' on my ubuntu 11.04 so don't use it... if you are gonna be using alpharevX to root your phone do not do it on a virtual machine (wouldn't work on my winxp in VMware Player, the phone would just reboot and get stuck), do it on a proper win machine.
ameya88 said:
HEy I have successfully turned S-OFF. When I try doing the Clockwork recovery thing it gets struck at waiting for device!! Any advice??
Click to expand...
Click to collapse
After s-off, waiting for device should be in the fast boot flashing recovery process. If it is so, the device is to be connected in fastboot mode and then the command "fastboot flash recovery recovery.img" is to be entered from command prompt (command prompt cd into fastboot folder, and recovery.img is also to be kept in this folder). The waiting for device warning around 1min is normal but shouldn't take more.
Ignore if going with other process.
Sent from my HTC Wildfire using XDA App
bharatgaddameedi said:
After s-off, waiting for device should be in the fast boot flashing recovery process. If it is so, the device is to be connected in fastboot mode and then the command "fastboot flash recovery recovery.img" is to be entered from command prompt (command prompt cd into fastboot folder, and recovery.img is also to be kept in this folder). The waiting for device warning around 1min is normal but shouldn't take more.
Ignore if going with other process.
Sent from my HTC Wildfire using XDA App
Click to expand...
Click to collapse
Tried it but device still gets stuck at <waiting for device> mode after I type fastboot flash recovery wildfire.img
ameya88 said:
Tried it but device still gets stuck at <waiting for device> mode after I type fastboot flash recovery wildfire.img
Click to expand...
Click to collapse
Make sure your Wildfire is in Fastboot Mode. Power Down your phone, Start with Vol Down + Power Key. This will open Bootloader Mode. Then connect to your PC with the USB Cable, Select "Fastboot' mode (By using Volume keys), and Press Power button on it.
gogusteliade said:
try this way http://forum.xda-developers.com/showthread.php?t=1130044
Click to expand...
Click to collapse
Hey thanks for the Link. I am now trying to follow the method posted in the link. Do I need to do the Hboot driver download and install thing after that or do i directly root??? Thanks by the way
3xeno said:
Make sure your Wildfire is in Fastboot Mode. Power Down your phone, Start with Vol Down + Power Key. This will open Bootloader Mode. Then connect to your PC with the USB Cable, Select "Fastboot' mode (By using Volume keys), and Press Power button on it.
Click to expand...
Click to collapse
No wonder!!! I was doing it wrong. Thanks will give it a try!!
3xeno said:
Make sure your Wildfire is in Fastboot Mode. Power Down your phone, Start with Vol Down + Power Key. This will open Bootloader Mode. Then connect to your PC with the USB Cable, Select "Fastboot' mode (By using Volume keys), and Press Power button on it.
Click to expand...
Click to collapse
I did as you said, Once I connected the phone to the PC while it was in boot loader I got a msg on the pc saying "driver not correctly installed" but I continued anyway and chose fast boot by pressing the power button. Now its giving me 4 options -> Bootloader, Reboot, Reboot Bootloader and Power down with the Title Fastboot USbB at the Top. Which do i choose??/
Are you shore u have all the files in the same folder and you need to have USB Debugger ON to.
The Alpharev take to long to finish. It`s happening the same with me.....
and you must put the code given by Alpharev website.
ameya88 said:
Now its giving me 4 options -> Bootloader, Reboot, Reboot Bootloader and Power down with the Title Fastboot USbB at the Top. Which do i choose??/
Click to expand...
Click to collapse
Don't choose anything.
This is the fastboot mode what everyone is talking about
Sent from my HTC Wildfire using XDA App
Damag3 said:
Are you shore u have all the files in the same folder and you need to have USB Debugger ON to.
The Alpharev take to long to finish. It`s happening the same with me.....
and you must put the code given by Alpharev website.
Click to expand...
Click to collapse
Yeah USB debugger is ON and all the files are in the same folder. I am just having a prob with the clockwork recovery thing. I successfully turn S-OFF
hi guys.. could you help me with my problem.!
I have an LG GT540 android 1.6 firmware version(stock)
So here are my problems:
1. I tried to upgrade it from 1.6 to 2.1 using this tutorial http://forum.xda-developers.com/show...27&postcount=3 thanks to lavero.burgos for posting it, I was successful at first part, but I cant follow the next because my device wont go to fast boot,, I tried putting it off, then camera+poweron but it doesnt do anything. It doesn't light, no lg logo appears, just nothing although the computer can read the drive when I connect it through usb. So I cannot flash it to 2.3,2.3 because it just wont go to fastboot.
2. When I turn it on normally, It takes long before it response like after 30sec to light, but just light, no lg logo appears although it wasnt bricked because I can use it normally after just waiting to on.(annoying)
3. Since I upgraded it to 2.1, I lost all 3rd party application and the internal apps were the only left, so I copied all my saved apps (.apk) to my sd card but the problem is there is no saved app on my phone to read and install those apps from my sd card.(irritating)
4. My device wont read my sim card, when I start it it says "sim card unprovisioned" so basically I cant connect to mobile networks here in the philippines(im using globe telecom). I feel that Im stucked in the middle of nowhere since I cannot contact and txt all my family and friends.
5. I cant connect to wifi,, when my device detects wi-fi, I try to connect to it but from the log it only try to connect but doesn't obtain the ip address. Even when the wi-fi signal is strong, it does the same thing.
So please help me guys,,I want to hear from my fellow xda-developers badly,,,
PS. also those who have problems with their LG GT540 pls feel free to post and share it with us here... thank you all guys in advance....
hi so let me get it right the phone is working (can turn on and use but cant call) yes? hmmmmm..... try this
MUST DOWNLOAD THIS DRIVERS!!!!
http://dottech.org/android/26188/usb-adb-and-fastboot-drivers-for-windows-for-all-android-phones/
Step one!
1.turn off phone.
2.hold the POWER button till you feel the beep.
3.let go of the POWER button when you feel the beep and hold onto the CAMERA button only.
4.hopefully it turns on to a blackscreen and nothing else(fastboot)
5.unzip this CLICK ME!! to desktop and open the flash all no wipe file
or......
1.turn on your phone.
2.go to settings>applications>development>tick the usb debugging
3.connect phone to computer (make sure phone is on)
4.unzip this CLICK ME!! to desktop and open the flash all no wipe file
5. phone should boot into blackscreen like the one above......
Click to expand...
Click to collapse
Step 2!
both should flash a recovery image. Next
1.make sure the phone is off
2.press POWER button
3.when you feel the beep let go of POWER button and press the HOME button only.
4.phone should boot into recovery mode.
5.take out battery again
6. download a rom into the sdcard using computer
7.go to recovery again using the steps above (steps 1 to 4)
8.select wipe all data factory reset or something like that....
9.install zip from sdcard
10.select from sdcard
11.choose the file you downloaded
12.finish flash and reboot phone.
Click to expand...
Click to collapse
excellent guide! big thanx
bs828 said:
hi so let me get it right the phone is working (can turn on and use but cant call) yes? hmmmmm..... try this
MUST DOWNLOAD THIS DRIVERS!!!!
http://dottech.org/android/26188/usb-adb-and-fastboot-drivers-for-windows-for-all-android-phones/
Click to expand...
Click to collapse
Thanks,, Ive tried the 2nd option on step one and i think my phone successfully got to fastboot(just clean blank screen) so the cmd automatically run and states
C:\Desktop\adb rebootloader
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
error: protocol fault <no status>
C:\Desktop\fastboot flash recovery recovery.img
< waiting for device >
Did I miss something???
ok try again this time with the phone turned on. and then run the script and did you install the drivers?
bs828 said:
ok try again this time with the phone turned on. and then run the script and did you install the drivers?
Click to expand...
Click to collapse
yeah I installed the drivers...
hmmm maybe there are no fastboot drivers(main suspect....) there are a few ways to get it but for mine i just plug my phone in to my pc (windows 7 64bit) it just recognize it and tries to get the "google fastboot interface" drivers from windows update...
Try Volume Up+Search Key+Power to go into Fast boot Mode, There's different keys to activate Fastboot Mode (There is different versions of Fastboot)
Sent from my LG GT540 CM9 PreRC Polish Blood using xda premium
Your phone is/was bricked
Hey, I'm sorry to bing back such an old thread, but I just wanted to say this for posterity: your phone has/had a soft-brick. This means: you can't see Android nor LG boot logos, can't enter Recovery and (maybe) can't access Fastboot, but I'm not too sure on that last one. Besides that, the phone works "okay", but you should try to fix it.
Basically this soft-brick is almost always caught when upgrading from 1.6 to 2.1, so everyone should have it, including me. It took me a whole year to realize how to friggin' fix it lol, but here goes what I did:
Thanks for your help everyone, I came to a solution after a full year lol. Here's my enlightenment, from another Thread:
------------------------------------------------------------------------------------------
Just wanted to leave my 2 cents here, I've been trying to do my best since around august 2014, no success. 2 days ago I retried this, and I DID IT! I will tell everyone what I did very shortly:
My problem that I solved: I can boot, device works like a charm. But: no boot logos, no recovery.
My solution for TL;DR: UNINSTALL ALL DRIVERS FROM DEVICE MANAGER 1ST, then reinstall. After that, flash a fastboot ROM and use it to WIPE ALL THE DATA IN YOUR PHONE! THIS was what I needed and was never explained: you had to WIPE the old data in order to get the boot screens back.
IN THIS ORDER (THANK YOU to those people from previous replies, gathering all your info was of great value):
Uninstall all of your phone drivers from your PC!!! This is what made most of my headaches go away, just use Device Manager and uninstall anything from LGE. After that, plug in your device in your USB ports (always BACK ports, not front ports, important). It should detect all drivers and download them.
IF it fails (it generally does with LGE USB Modem), you can go to Device Manager > Unknown Device (the one that wasn't recognized) > Right Click and Update > Choose 2nd option, then choose "choose from a list of local controllers" (or whatever the button says). After that, scroll down to LG Electronics, Inc. and install what didn't install.
I also found these drivers, but I did not test them: http://www.mediafire.com/download/p693hcz6kkouh19/USB_Driver_LG_GT540.zip
Huzzah!
Now you're set to begin:
FIRST thing you wanna do is a factory reset, this is something I'd forgotten with time, don't make the same mistake as I did. You can do it by turning your phone on and pressing Volume +/- & Home & Quick Search buttons all together for 5 seconds (it works, be patient and wait for it, even if you open the camera or any other stuff).
Download this Google SDK Tools (unzip and put the folder in C:\ drive) and this Fastboot drivers for GT540 (unzip and put the files inside the folder in C:\android-sdk).
Skip this next line if you know your ROM has fastboot.
Now, if you don't have a ROM with fastboot, I recommend you use either European Open+Fastboot or V20C Orange France Fastboot ROM.
Click to expand...
Click to collapse
Since you have Fastboot enabled, now all you need to do is turn off your device (all this with its battery on it, no weird things) and hold the Camera button before turning it back on. This should take you either to a black screen, or simply to no display, like me. Either one will work anyways.
Now press the Windows key > Type cmd and open it with Right Click > Run as Administrator.
In it, type all this, command by command (you can paste by right clicking):
cd C:\android-sdk
fastboot -w
fastboot erase boot
fastboot erase system
fastboot -w
fastboot reboot
Click to expand...
Click to collapse
And now it's go time! Do what everyone else says in here: Take out your phone's battery, SD and SIM cards, fire KDZ Updater up as Administrator (If your KDZ freezes, then it's either faulty or you did not install msxml, look for a good KDZ that comes with that file and delete your current one), choose CS_Emergency PhoneMode and:
1-Plug your phone while holding the volume DOWN button (don't worry! My phone didn't show "Download Mode" either, if you hear the Windows "Somethingpluggedin" Bump noise, it's ok).
2-Flash French V20A
3-Unplug your phone once KDZ says "==FINISHED==".
4-Plug it once again, holding the volume DOWN button.
5-Flash out.kdz (remember! it's CS_Emergency).
Click to expand...
Click to collapse
THANK YOU XDA!
--------------------------------------------------------------------------------------
Also, if you look in here you'll find how to flash an awesome ROM, Cyanogen Mod 10 (should say "Final Version#2).
Hello, I'm new to xda, in fact I registered just to ask for help. My p9 lite got stuck on huawei logo, when i try to turn off the device it just reboots 2 times and then just stays on huawei logo. I can enter fastboot and rescue mode, but i have not enabled usb debugging and oem unlock on the device earlier. To be honest this is my first android device, in the past i used only windows phones, so you could say i'm completely new to this. Any suggestions on how to recover my phone or flash any rom into it? I'd be very glad if someone helped me find the solution to this problem. Not sure if i made a thread in the correct place, direct me if i'm mistaken
There are few different versions of P9 Lite, look at the back of the phone to the bottom to see the numbers beside VSN and let us know.
1) Also when the phone is turned off plug in the usb to a computer or charging adapter
2) Hold down volume up & power
3) Let go of the power button when you feel the buzz while still holding the volume up button
4) Download latest version & recovery.
5) Go to Settings>Developer Options>USB Debugging On
5B) If you don't see Developer Options in settings, then go to Settings>About Phone>Build Number & ( tap the Build Number untill it unlocks)
6) Update us on the status, hope it works out.
GloryNation said:
There are few different versions of P9 Lite, look at the back of the phone to the bottom to see the numbers beside VSN and let us know.
1) Also when the phone is turned off plug in the usb to a computer or charging adapter
2) Hold down volume up & power
3) Let go of the power button when you feel the buzz while still holding the volume up button
4) Download latest version & recovery.
5) Go to Settings>Developer Options>USB Debugging On
5B) If you don't see Developer Options in settings, then go to Settings>About Phone>Build Number & ( tap the Build Number untill it unlocks)
6) Update us on the status, hope it works out.
Click to expand...
Click to collapse
tried to enter recovery, still not work. can't go to developer options because phone is stuck on logo, can't power off. couldn't find any solution that works anywhere, been searching for more than 6 hours, still no use. phone model is VNS-L21 forgot to mention earlier
What exactly were you doing before this happened and does your computer recognize your phone when plugged in at all.
Try holding volume up & down together & plug phone in when it reboots on you, & report back with what you see. If anything at all.
GloryNation said:
What exactly were you doing before this happened and does your computer recognize your phone when plugged in at all.
Try holding volume up & down together & plug phone in when it reboots on you, & report back with what you see. If anything at all.
Click to expand...
Click to collapse
I tried to install nougat update, computer recognizes it only in fastboot. holding volume buttons haven't changed anything still no progress. the thing is i had installed nougat a moth or so ago and it worked fine, then rolled back to marshmallow and now this. i'm pretty sure i tried to install correct package, because it was the same i had installed earlier
Did you download a adb tool on your computer that have the 'fastboot.exe' file? If so open that folder,
Have the mouse curser hover in that folder, hold down shift & right click the mouse
Open command prompt
Connect phone as is in fastboot mode
Type adb devices & press enter
Type adb continue & press enter
Hi,
I have the same issue as ellanyx.
my phone can only be stucked while booting or if I connect my phone to a computer, I'm able to boot it in fastboot.
as ellanyx, I didn't enable usb-debug nor OEM unlock option...
so when I'm in fastboot, I type the command "fastboot oem unlock xxxxxx" (hopefully the different data needed are the correct ones mentioned on the box of the phone) I get this error message:
C:\Users\Dieu\Downloads\SRKToolHuawei-STABLE-V1.3-20160619>fastboot oem unlock xxxxx
...
FAILED (remote: Command not allowed)
finished. total time: 0.016s
and off course the other options like "fastboot flash recovery recovery.img "... doesn't work.
I can't use the adb commands neither.
when I type the commande, as mentioned above, "adb devices" or "adb continue", nothing works.
So I'm a bit desesperate
do you have any solution for this kind of issue?
thanks
Dude, so the last firmware on your phone was MM or N? If it was MM you should put stock firmware appropriate for your model in dload folder on SD card and put volume+volume-power, and thats it. If you stack on N,....then I dont know because dload method doesnt work with N, or maybe works if you can find stock firmware with recovery for N.
Regards
Unfortunately I can't update with the 3 button update otherwise it would indeed solvemy problem.
pyromana said:
Unfortunately I can't update with the 3 button update otherwise it would indeed solvemy problem.
Click to expand...
Click to collapse
Probably you didnt have correct Oeminfo for MM if dload method didnt work....Try to conect phone with Toolkit and follow procedure for flashing oeminfo and custombin, after that flash stock recovrry and b161 via dload metod. You will find it on forum here.
Regards
the procedure from SRK toolkit?
would it be possible to provide it? because I can't unlock the OEM and I didn't tick the USB debug think.
Maybe problem with the ps not phone so u can not connect with adb
Try with different pc you must have flash oem with fast boot without enable adb from phone if u in fastboot
I can only boot my phone in fastboot (vol- + power) and not in recovery (vol+ + power).
also when using the SRK toolkit, the first screen tells me to be sure that the usb debugging is enable, which I haven't done...
if I'm not mistaken, fastboot is to use the fastboot command and recovery the adb commands
the connection with fastboot works on my computer, the link is made. however when I type the command to unlock the OEM, I get an error stating that the command is not allowed.
when I use the SRK toolkit, with the different questions, he tries to connect the phone with adb and waiting.... waiting...
is there a command to reboot in recovery but from fastboot? in the otherway around it exists but it doesn't seem that from fastboot to recovery it exists.
thanks.
Alexxxx1 said:
Dude, so the last firmware on your phone was MM or N? If it was MM you should put stock firmware appropriate for your model in dload folder on SD card and put volume+volume-power, and thats it. If you stack on N,....then I dont know because dload method doesnt work with N, or maybe works if you can find stock firmware with recovery for N.
Regards
Click to expand...
Click to collapse
dload method works on N. I downgraded my phone from unofficial N update back to official MM update using this method yesterday. You just have to enable OEM at developer options on settings.
It looks like people can't be bothered to read the 1st post properly before they reply.
HE CAN NOT BOOT TO ANDROID SO HE CAN NOT ENABLE OEM OR ACTIVATE USB DEBUGGING!!!!
What he CAN do, is go into eRecovery and Fastboot.
With that in mind, I would suggest using the dload method through fastboot.
Also, make sure it is Huawei SRK Tools 2.0 that is used, as it actually asks if you are in debug mode or fastboot.
Note that there is a few bugs in SRK 2.0:
The TWRP recovery file has the wrong filename in the package, so it WILL fail unless you name it correctly.
Also, when trying to root, do NOT use the "P9 Lite" method as that WILL fail too. Use the "P9/P9 Plus" method.
I am trying to set up a complete guide that can restore the phone when it is stuck in fastboot, however I apparently went a step too far...
ellanyx said:
Hello, I'm new to xda, in fact I registered just to ask for help. My p9 lite got stuck on huawei logo, when i try to turn off the device it just reboots 2 times and then just stays on huawei logo. I can enter fastboot and rescue mode, but i have not enabled usb debugging and oem unlock on the device earlier. To be honest this is my first android device, in the past i used only windows phones, so you could say i'm completely new to this. Any suggestions on how to recover my phone or flash any rom into it? I'd be very glad if someone helped me find the solution to this problem. Not sure if i made a thread in the correct place, direct me if i'm mistaken[/QUOTE
Do you have TWRP recovery ?
---------- Post added at 09:55 AM ---------- Previous post was at 09:50 AM ----------
ellanyx said:
Hello, I'm new to xda, in fact I registered just to ask for help. My p9 lite got stuck on huawei logo, when i try to turn off the device it just reboots 2 times and then just stays on huawei logo. I can enter fastboot and rescue mode, but i have not enabled usb debugging and oem unlock on the device earlier. To be honest this is my first android device, in the past i used only windows phones, so you could say i'm completely new to this. Any suggestions on how to recover my phone or flash any rom into it? I'd be very glad if someone helped me find the solution to this problem. Not sure if i made a thread in the correct place, direct me if i'm mistaken
Click to expand...
Click to collapse
Boot into fastboot mode and flash a custom recovery by meticulus. Link : meticulus.co.vu
Then whenyou get stuck hold power and vol down button for 2 minutes the phone will reboot and then when it says that your device has been unlocked and cant be trusted then only press vol up key ( dont press power button then). The u get into huawei recovery. From that u should power off the phone. Now get a custom rom by meticulus into your device sd card ( Cyanogenmod 13 is recommended ). Then insert sd card in a powered off phone. Now press vol up and power key and flash gapps and custom rom and you are good to go.
Click to expand...
Click to collapse
So, MY question:
I have tried 4 times to get Nougat installed, but every time I got the SMALL package (1.25gb) which means it is not complete.
I decided to try ONE more time, but think I have made a serious mistake.
I was on B161 and tried to downgrade to B160 without upgrading to Nougat first.
This has caused my phone to be stuck at boot with the message "Your device is booting now..."
I can NOT get into eRecovery or fastboot no matter what I do.
If I just leave the phone, then it discharge very fast, but as soon as I plug it in, it starts up and gets stuck at the same screen again.
Does anyone have ANY idea about how I can get out of this problem?
UPDATE:
I have managed to boot to fastboot while connected to my pc.
The phone is unlocked but FRP is LOCKED, which means I can't flash anything.
I read about using Miracle Loader to remove the FRP lock, but it can't "see" my phone. Maybe I am doing it wrong?
SnowmanDK said:
So, MY question:
I have tried 4 times to get Nougat installed, but every time I got the SMALL package (1.25gb) which means it is not complete.
I decided to try ONE more time, but think I have made a serious mistake.
I was on B161 and tried to downgrade to B160 without upgrading to Nougat first.
This has caused my phone to be stuck at boot with the message "Your device is booting now..."
I can NOT get into eRecovery or fastboot no matter what I do.
If I just leave the phone, then it discharge very fast, but as soon as I plug it in, it starts up and gets stuck at the same screen again.
Does anyone have ANY idea about how I can get out of this problem?
UPDATE:
I have managed to boot to fastboot while connected to my pc.
The phone is unlocked but FRP is LOCKED, which means I can't flash anything.
I read about using Miracle Loader to remove the FRP lock, but it can't "see" my phone. Maybe I am doing it wrong?
Click to expand...
Click to collapse
Try to relock and then unlock the bootloader again. And make sure oem unlocking is enabled in dev options
Arsaam said:
Try to relock and then unlock the bootloader again. And make sure oem unlocking is enabled in dev options
Click to expand...
Click to collapse
Please read my previous post again
I can NOT boot normally. And as FRP is locked, then I can't relock or unlock the bootloader.
SnowmanDK said:
Please read my previous post again
I can NOT boot normally. And as FRP is locked, then I can't relock or unlock the bootloader.
Click to expand...
Click to collapse
Go to fast boot mode and from their try to flash meticulus recovery.
You can also try the adb method as well.
Visit meticulus.co.vu
Hi everyone, i have a big problem. Today i was trying to help a firend of mine by unlocking his bootloader on this phone but i got a strange message when i was trying to boot in Download mode. The message was:
"fastboot init( )
loading keystore failed status 5 usb init ept @ 0x8f20700
udc_start( )
fastboot: processing commands"
Basically it doesn't allowed me to enter in Download mode, so no reverting to v10f software, no pushing aboot, no twrp and no Marshmallow zip. Nothing at all, i could do nothing. In the following lines i will tell you what i did and tried:
1) Using different PC usb ports, no way to make it work
2) Using different cables, no way to make it work
3) Trying to boot in Download mode by removing battery and try without it, desperate, obviously no way to make it work
I spent two hours trying to find a way to make it work but i failed miserably...so i'm here hoping someone better than me can help me.
NOTES:
The phone was on original Lollipop firmware v10e (Italy) but rooted.
Basically i did nothing, just tried to put it in download mode (Vol - and plug usb in), tried also other ways but nothing showed up
When the phone is connected to pc (when it's on) it charges only, don't show the option to use mtp so... i think adb won't work
Hope it can help and hope you can help! XD
I had same error, cause of flashing the wron zip basically i needed to get into repair mode and use adb while its trying to repair use adb commands to reboot to recovery
Sent from my LG-H440 using Tapatalk
MadjijaHacker said:
I had same error, cause of flashing the wron zip basically i needed to get into repair mode and use adb while its trying to repair use adb commands to reboot to recovery
Sent from my LG-H440 using Tapatalk
Click to expand...
Click to collapse
But i need Download mode, not recovery. With adb i can access it?
P.S i didn't flash anything
Well, that's what helped me, i don't know was that helpful, you can still try repair mode
Giuskiller said:
But i need Download mode, not recovery. With adb i can access it?
P.S i didn't flash anything
Click to expand...
Click to collapse
Sent from my LG-H440 using Tapatalk
Giuskiller said:
Hi everyone, i have a big problem. Today i was trying to help a firend of mine by unlocking his bootloader on this phone but i got a strange message when i was trying to boot in Download mode. The message was:
"fastboot init( )
loading keystore failed status 5 usb init ept @ 0x8f20700
udc_start( )
fastboot: processing commands"
...
NOTES:
The phone was on original Lollipop firmware v10e (Italy) but rooted.
Basically i did nothing, just tried to put it in download mode (Vol - and plug usb in), tried also other ways but nothing showed up
...
Hope it can help and hope you can help! XD
Click to expand...
Click to collapse
Upload mode is phone off, press VOL+ and then plug the USB.
---------- Post added at 04:57 PM ---------- Previous post was at 04:55 PM ----------
MadjijaHacker said:
I had same error, cause of flashing the wron zip basically i needed to get into repair mode and use adb while its trying to repair use adb commands to reboot to recovery
Sent from my LG-H440 using Tapatalk
Click to expand...
Click to collapse
Can you give more details? How can I access that repair mode and how to use adb commands on it? I have a bricked board that I want to put back on use.
jorlando said:
Upload mode is phone off, press VOL+ and then plug the USB
Click to expand...
Click to collapse
Hi, i tried vol + but the phone just boots... i will try again and let you know in the evening
When device is off hold Vol- and power key until LG logo appear, then release the keys and hold them again, its really hard to time it correctly, but if you do you will get a factory reset option, on that screen you navigate using Vol+ and - buttons and power button is ok
Sent from my LG-H440 using Tapatalk
MadjijaHacker said:
When device is off hold Vol- and power key until LG logo appear, then release the keys and hold them again, its really hard to time it correctly, but if you do you will get a factory reset option, on that screen you navigate using Vol+ and - buttons and power button is ok
Sent from my LG-H440 using Tapatalk
Click to expand...
Click to collapse
Thank you, after the factory reset the combination Vol+ and USB worked (after a few try) and i was able to boot in Download mode, then i flashev v10f, rooted and pushed modified aboot, flashed twrp 1.1.0 with flashify (twrp official app failed many times) and finally installed v20b and supersu. Everything works as expected =)
Giuskiller said:
Thank you, after the factory reset the combination Vol+ and USB worked (after a few try) and i was able to boot in Download mode, then i flashev v10f, rooted and pushed modified aboot, flashed twrp 1.1.0 with flashify (twrp official app failed many times) and finally installed v20b and supersu. Everything works as expected =)
Click to expand...
Click to collapse
I am glad i could help [emoji2]
Sent from my LG-H440 using Tapatalk
oh man same problem if u fix this let me now how plzzzzzzz
Silentsx1 said:
oh man same problem if u fix this let me now how plzzzzzzz
Click to expand...
Click to collapse
Is there anything you can do on your phone or is it completely dead ?
I can enter the hardrester but itis not helping and in fastboot itis saying FAILED (remote: unknown command)
Silentsx1 said:
I can enter the hardrester but itis not helping and in fastboot itis saying FAILED (remote: unknown command)
Click to expand...
Click to collapse
Try to boot into download mode, if you can. Turn off your device then press and hold vol. Up and plug in the cable.
i cant turn off my device legit after i put battery fastboot show up :crying::crying::crying::crying:
Silentsx1 said:
i cant turn off my device legit after i put battery fastboot show up :crying::crying::crying::crying:
Click to expand...
Click to collapse
Can you post a screenshot here ?
here i cant do anything plz help
https://ibb.co/kmZCmG
https://ibb.co/eMB3tw
https://ibb.co/mQsMfb
https://ibb.co/dpf7Lb
Silentsx1 said:
here i cant do anything plz help
https://ibb.co/kmZCmG
https://ibb.co/eMB3tw
https://ibb.co/mQsMfb
https://ibb.co/dpf7Lb
Click to expand...
Click to collapse
Do you have twrp installed on your phone ? If, yes try to boot into it.
I have a similar problem with my LG Spirit. When it tries to boot, it shows an error message: Boot Verification Fail, DIFFERENT_HASH... After that it just restarts endlessly... I can't enter download mode, because the computer doesn't recognize it when I plug it in via usb cable... The only thing I can do is to get to the hard reset screen, but that is useless because it just restarts and shows the same error mentioned above... I'm out of ideas, the only thing that comes to my mind is to try and see if Ubuntu recognizes it, but then again, there's no LG Flash Tool made for Linux, or is there?
Sorry for mistakes, english is not my native language.
Hrastostit said:
I have a similar problem with my LG Spirit. When it tries to boot, it shows an error message: Boot Verification Fail, DIFFERENT_HASH... After that it just restarts endlessly... I can't enter download mode, because the computer doesn't recognize it when I plug it in via usb cable... The only thing I can do is to get to the hard reset screen, but that is useless because it just restarts and shows the same error mentioned above... I'm out of ideas, the only thing that comes to my mind is to try and see if Ubuntu recognizes it, but then again, there's no LG Flash Tool made for Linux, or is there?
Sorry for mistakes, english is not my native language.
Click to expand...
Click to collapse
If your pc doesn't recognise it, try to find an another computer that you can try it on .
mayankjet said:
If your pc doesn't recognise it, try to find an another computer that you can try it on .
Click to expand...
Click to collapse
Thank's for your reply. I did just that, but without success... I also tried to do what MadjijaHacker wrote, but I can't get it right. I mean, I can enter in hard reset, but can't get to download mode. It seems that my phone is dead...
Hello guys, how are you today ?
I will do my best to write properly (french, sad)
So, i unlocked my phone with no problem. I tried to install a working TWRP. The ADB command to install was easy, but impossible to boot in twrp with the boot command on ADB.
I understood that i just needed to press up and power to open TWRP.
I putted on my OTG USB KEY the xiaomi.eu weekly ROM for my phone.
I formated only DATA, and i began the installation.
I had an error, and after my OTG was not recognize.
I just putted up and power to reboot the phone and try again.
But i dont know what happened, black screen, impossible to boot on something, i tryed to hold power 15 sec and nothing work, impossible to go to fastboot mode.
The phone is recognized on windows but nothing more.
I searched on the net and my phone is bricked. I need to open it to press ELD.
I found someone who has ELD permission for 12$.
Now i just want to know if someone can explain me how to open without damage the phone and how to be in ELD mode.
Thanks you and have a nice day.
I guess you could try to buy an EDL cable instead.
How you see phone in device manager?
newhope81 said:
Hello guys, how are you today ?
I will do my best to write properly (french, sad)
So, i unlocked my phone with no problem. I tried to install a working TWRP. The ADB command to install was easy, but impossible to boot in twrp with the boot command on ADB.
I understood that i just needed to press up and power to open TWRP.
I putted on my OTG USB KEY the xiaomi.eu weekly ROM for my phone.
I formated only DATA, and i began the installation.
I had an error, and after my OTG was not recognize.
I just putted up and power to reboot the phone and try again.
But i dont know what happened, black screen, impossible to boot on something, i tryed to hold power 15 sec and nothing work, impossible to go to fastboot mode.
The phone is recognized on windows but nothing more.
I searched on the net and my phone is bricked. I need to open it to press ELD.
I found someone who has ELD permission for 12$.
Now i just want to know if someone can explain me how to open without damage the phone and how to be in ELD mode.
Thanks you and have a nice day.
Click to expand...
Click to collapse
Can you get into fastboot
My phone was completely stuck in black screen impossible to go on fastboot mode.
Luckely, i dont know how but my phone was recognized like if i was in EDL mode.
I contacted an asian man on WhatsApp, he putted his logs on miflash to allowed EDL flash.
My phone is Alive now!
Where Can i buy an EDL cable if i need it ? It replace the open of the phone?