Hey everyone, I recently got hold of a HP iPAQ 614c from a friend, and was playing with it. I've had it about a week and so far it's been a lot of fun to play with. Downloaded and used the WM6.1 Manila and then WM6.5 Manila (v0.5) from this forum, and all was working super.
Now a day or so ago, I noticed my phone just totally stopped recognising the USB cable connected to it, and I need some advice as to what to do. It's not detecting the USB either in A/C charge mode, or when connected to my laptop, the laptop isn't detecting it as a device at all.
There is nothing wrong with either battery (a normal and a high capacity, both were working and charging fine before).
I've tried replacing, downgrading and re-upgrading the ROMs, and nothing seems to be working. I've also tried twiddling the cable connection to see if I can get it to respond (even temporarily, which would suggest a lose or damaged connection).
Luckily with the high capacity battery, I got about a week to fix it (if it's fixable) so long as I keep the wi-fi disabled.
Now what I want to know from you guys is if you think it's one of the following scenarios:
1. The USB interface on the phone is damaged (either from being knocked or dropped).
2. The cable has become damaged.
3. I've fudged something inside by using the unofficial ROMs.
And what, if anything I can do about it.
Much appreciated any help.
are you using the original charger?
HP614c recognizes the original charger and informs you about charging in other cases you need to turn on USB charging in system
if you have no response from USB it may be a damaged usb interface eg. the connector or charging IC or USB interface IC.
did you try on other PC/USB port or/and other cable
also check in device manager of PC for any suspicious looking USB devices
i can't turn on wifi , updated to mk809 fw1228 via usb otg still no go , also flashed with imito_mx1_finless_1_5 but wifi dont work how to fix it??
autokat said:
i can't turn on wifi , updated to mk809 fw1228 via usb otg still no go , also flashed with imito_mx1_finless_1_5 but wifi dont work how to fix it??
Click to expand...
Click to collapse
I'm having the same problem. The only thing that works is to unplug the device for a minute and plug it back in. I still looking for a permanent fix. Perhaps it is overheating or the antenna sucks. I'm thinking about opening mine up to take a look...
Not sure if this helps: I was able to kill the wifi by placing my hand over the android icon on the case for a few seconds (I did it a few times to make sure it wasn't a fluke). It seems as though the wifi never reconnects after a drop and I have to restart the device to get it back.
More info: I have been powering the device from an empty usb port on the TV. If I use the included adapter, it seems to be a little bit less flaky. For example, I can cover the device with my hand and it wont kill the wifi.
ok thanks i will buy a new one MK809II this one worked only 1 day:crying:
glitterbug said:
More info: I have been powering the device from an empty usb port on the TV. If I use the included adapter, it seems to be a little bit less flaky. For example, I can cover the device with my hand and it wont kill the wifi.
Click to expand...
Click to collapse
Try using a UG802 rom...
glitterbug said:
More info: I have been powering the device from an empty usb port on the TV. If I use the included adapter, it seems to be a little bit less flaky. For example, I can cover the device with my hand and it wont kill the wifi.
Click to expand...
Click to collapse
I have a mk809 bought from Justop. I used an old mobile phone charger that outputs 1A. This is the absolute minimum as you should use a 2A power supply. I only use the USB port for a wireless dongle for my perixx keyboard/mouse.
A USB port from a TV will not provide the full 2A power supply - at best you'll get 1A but, more likely, less than that.
For all the others out there having strange behaviour and/or reboots/wifi drops etc have a look at the power output of your power supply and make sure you are giving it a reliable 2A.
A lot of problems with Android sticks have been solved this way.
Hope this is useful to someone!
ok but i only use the usb power that came with the mk809 , i am thinking of trying a wifi wireless usb dongle, do you know which one will work
Im using my Nexus 7 as my car radio with Timur's Rom but I have one problem. When the tablet goes into deep sleep mode, the tablet doesn't charge anymore unless I disconnect the otg y cable and reconnect it. I've been researching on how to fix this problem for a while now with no solution. I looked up all the settings in the rom and there is nothing to help with this. I also tried using tasker to simulate disconnecting and reconnecting the usb cable but couldn't figure it out. Anyone have any solutions that I could try? I have the otg y cable connected to the ignition wire and also to a constant power with a switch. The other end goes into the tablet and the other end goes into my portable hard drive. I hate having to manually removing the tablet from the dash and removing and plugging back in the usb otg cable
hi guys
had a problem for a while where i can't charge it through a cable, but i can charge it through the wireless coil.
i just replaced the USB port, and now i get a reaction when i connect it to the computer, however there is an error about USB not recognised.
i guess i'm not looking for a solution but i want to know if anyone else had the same problem and whether it's like a mainboard problem? cos i better off getting a new phone...
bit of a curveball, not sure would anyone have any idea what happened to my phone
thanks
I'm using Android Headunit Reloaded which uses a USB cable to connect between my phone and my 7" TabA. The tablet ends up charging the phone. I was wondering if there was a way to prevent this- or even better- to have a y-splitter OTG cable to charge the tab and one for the phone. I suppose this would require custom kernels?
Any ideas would be helpful. Thanks.