Samsung Galaxy Tab 4 10.1 SM-T530 Bricked (Probably) - Galaxy Tab 4 Q&A, Help & Troubleshooting

Hello, sorry if in bad place, but im new here.
I have a problem with [Samsung Galaxy Tab 4 10.1 SM-T530].
I had a custom rom, but now i flashed stock rom. When it booting i see "Samusng GALAXY TAB4" logo.
I can't find it in the internet because one thing is different. That difference is this, i hear all system sounds, like volume changing, when i touch somewhere, where is a button under this logo, i also hear a touch sound, and voice assistant when i by accident turn on it.
It look like system be turned on, but device showing a mask, wich mask is this Samsung logo.
And sorry for my bad english. ;P

Same for my problem from my SM-T531 before, but I fixed it by flashing the stock ROM made for my tablet.
Fix (I did this on my own without researching. It may work, but try)
I. Find the stock ROM made for your device (SM-T530) then download it. Make sure you select the correct region (Country in which where you bought the device)
II. Download Odin (the latest one)
III. Now open Odin on your PC. (Doesn't matter if you run it with Administrator, but recommended to open it with Admin rights)
IV. Boot your device to Download Mode (Power button+Volume Down+Home button)
V. Connect your device to the PC with the connector that came from the tablet
VI. Odin must detect your tablet
VII. Find and open the zip archive for the Stock ROM then extract the item inside the archive somewhere like your desktop.
VIII. Finished, now browse and find the file you extracted through Odin. (For browsing, click the AP button)
X. WAIT for few minutes!
XI. If it's finished checking the md5 file, check the F. Reset Time and Auto Reboot if not checked yet. Click Start if you're ready.
XII. WAIT for some minutes!!!
XIII. Finished, now it will boot. Remove the cable connector from the PC and wait for minutes
XIV. Now the boot process should show the animated Samsung Logo.
[This process will wipe every single data on your internal storage and /data/data folder so make sure you click the Start button if you really want to clear. I suggest you move the files on your Internal Storage to the computer to be safe. Make backups to be safer.]
Any discrepancies, post to the next reply and I'll fix it :good:

Related

"soft bricked" galaxy tab please help me

hello i have a problem my galaxy tab goes into recovery mode with the android man and the white box but if i try and select that with the volume up button it just turns off here is what i have been told too do
1) Download this file:
2) Put the file on your internal storage.-------I cant do!
3) Reboot into recovery-------------------------I can do
4) Execute the Wipe Data/Factory Reset option-----------------------cant do!
5) Choose Install Zip from SD Card--------------Cant do!
6) Choose Choose Zip from SD Card----------------------Cant do1
7) Select the P7310UEKHA_Restock_v1.zip--------Cant do!
8) Sit back, wait about 5 minutes
9) Once the script completes and says "Done", reboot.
10) Welcome to a completely stock US Retail tab
my device wont get picked up by my pc or kies tries to install a driver named "APX" then says unable to install
any help would be very much appreciated I'm rooted and was wondering if sent it back to Samsung would they know? im rooted because if i cant get access to anything they wont be able to will they? please help me
http://media.xda-developers.com/images/icons/icon9.gif
Follow this and download overcome gbsafe_v5 and then follow it up to loading the overcome_kernel4.0
davewestwood.net/Dave_Westwood_-_Infomation_Risk_Specialist/Overcome_Guide.html
If you need to help leave reply and i'll help to my best ability
Sent from my LG-P999 using xda premium
Samsung would know it is rooted before mine went back I flashed it with old Samsung firmware.
I once soft-bricked my OG Galaxy Tab and was able to unbrick it with a JTAG software application. I have it on my desktop at home. Unfortunately, I'm in the office right now, but I'll check when I get home and update with the name and a link if I can locate it.
The application I mentioned in my post above is called "One Click Unbrick." It works for any Samsung devices that use Odin 3, (which includes the Galaxy Tab 7.) I've used it a few times to recover from softbrick. I've been in a similar situation where I couldn't get into download mode and the computer didn't recognize the device when it was plugged in, but OneClick Unbrick did and managed to bring my tablet back to life. You can find it here:
http://forum.xda-developers.com/showthread.php?t=1153310
Good Luck.

Really Bricked my new Galaxy Tab 2 7 inch. I have tried everything :(

Hello, I so hope someone can help. I just updated my galaxy tab 2 7 p113 to Android 4.0.4 UEBLH2. That was done automatically from samsung. I wanted to then install the newest update to 4.1.1 jellybean. So I downloaded it from this link. http://www.trickytweaks.com/update-...ecli4-4-1-1-jelly-bean-ota-test-firmware.html. I put the official Android 4.1.1 UEBLH2 Firmware on my sdcard then held down my power and up volume and installed it. HOWEVER, it never finished installing. Went all the way to the end. Now I HAVE NO USB CONNECTION and NO BOOT UP. Just black Since I dont have usb connection I cant us oden. CAN ANYBODY PLEASE HELP? I still can put files on my micro disk card and then put sd disk in my tab and use the power button up arrow to install something but I tried installing clockwork mod but that did not work. Iam out of ideas. P.S. My tab IS NOT ROOTED. I tried updating back to and original rom 4.04 I download but that did work. Thank you.
I think you need to enter the download mode volume down+power or recovery mode volume up+power to be able to restore the tab
Try multiple times close the tab even with long pressing power then try the button combinations (press both for multiple seconds) and release to see if you could enter any mode
If you reached download mode try flashing stock firmware for your tab specific model 3113 or 3110 or 3100 via odin (install kies and reboot before)
If you reached recovery (stock) then connect with kies and choose recover firmware from kies options (near the word file in top) you should have active internet connection
You could try charging tab even for some hours before trying button cobinations
If not try to return as not rooted so warranty is goood
Sent from Galaxy S2 or Galaxy Tab2
Mohamedselim said:
I think you need to enter the download mode volume down+power or recovery mode volume up+power to be able to restore the tab
Try multiple times close the tab even with long pressing power then try the button combinations (press both for multiple seconds) and release to see if you could enter any mode
If you reached download mode try flashing stock firmware for your tab specific model 3113 or 3110 or 3100 via odin (install kies and reboot before)
If you reached recovery (stock) then connect with kies and choose recover firmware from kies options (near the word file in top) you should have active internet connection
You could try charging tab even for some hours before trying button cobinations
If not try to return as not rooted so warranty is goood
Sent from Galaxy S2 or Galaxy Tab2
Click to expand...
Click to collapse
Yup, this should get you going again. If you can get into download mode, you should be okay. That's what Odin needs.
Download mode is volume down plus power. Then volume up
Recovery mode is volume up plus power.
I want to thank both the posters on trying to help me. I did hold down the power and download button and it went in to the download mode. HOWEVER, since I can not access usb it did not do anything. Just kept saying downloading. As I mentioned in my first post I CAN ACCESS MY SD DISK FILES by doing the power up button thing. Thats the only way I can get files on. But the DOWNLOADING down arrow just does not do anything. hmmmmmmm will keep plugging away.
I can not understand how you can not access usb, is it a lacking driver so download kies and reboot and try connect again ,also try a different usb ports (esp the rear of case) of your computer
Was usb working before the problem?
do you have cwm or stock recovery?
If cwm so download cm10 or cm9 from www.teamhacksung.org and put in usb card and flash but do a cash delete and dalvik delete afterwards not for boot loop
If stock so try stock firmware from www.samfirmware.com (register their first) and put in sd card and try to flash
Sent from Galaxy S2 or Galaxy Tab2
growthweb said:
I want to thank both the posters on trying to help me. I did hold down the power and download button and it went in to the download mode. HOWEVER, since I can not access usb it did not do anything. Just kept saying downloading. As I mentioned in my first post I CAN ACCESS MY SD DISK FILES by doing the power up button thing. Thats the only way I can get files on. But the DOWNLOADING down arrow just does not do anything. hmmmmmmm will keep plugging away.
Click to expand...
Click to collapse
I think you're misunderstanding download mode. When you get the device in download mode, connect it then to the computer, with Odin open. The only reason Odin wouldn't recognize it would be a driver issue. In that case, do as the previous poster stated. When you're in download mode, you're strictly flashing through Odin. You aren't going to see the device as a storage device on the computer. The only way your computer can interact with it at this point is Odin. Via Odin, flash the proper p3113 firmware file from sammobile/samfirmware (will be a large 600mb+ file). Once that's done, you should then be back to completely stock and healthy recovery and ROM. Reboot tab and see what happens. If it boots, and you still want to update, then make sure you get the correct ota for the base file you just flashed (that is, if you're trying to upgrade to say Jellybean). If you need more help always ask, but you should be fine. If I lived nearby I'd do it for you.
All I can say is unbelievable help here! Thank you. I am spending hours on this (plus a fortune on this new Tab 2 7). After studying up I do now understand how Odin works and how grabbing the correct firmware will do the job. HOWEVER (maybe others come across this huge roadblock) nothing can be done with out usb interaction. I DID DOWNLOAD KIES and installed it. But no matter what I do can not get any storage device listed or anything going on between tab and computer. Only thing my Tab does is when I plug it in to the computer via usb is go in to charging mode with the charging icon showing. Loading Odin does not show any connection. I have tried different computer USB plugins, 3 different computers (all I have loaded Kies on). Iam sooooooo close. If only while in the POWER BUTTON DOWN ARROW DOWNLOAD MODE and running ODIN on my computer there would be a connection I would be home free and able to flash firmware.
dictionary said:
I think you're misunderstanding download mode. When you get the device in download mode, connect it then to the computer, with Odin open. The only reason Odin wouldn't recognize it would be a driver issue. In that case, do as the previous poster stated. When you're in download mode, you're strictly flashing through Odin. You aren't going to see the device as a storage device on the computer. The only way your computer can interact with it at this point is Odin. Via Odin, flash the proper p3113 firmware file from sammobile/samfirmware (will be a large 600mb+ file). Once that's done, you should then be back to completely stock and healthy recovery and ROM. Reboot tab and see what happens. If it boots, and you still want to update, then make sure you get the correct ota for the base file you just flashed (that is, if you're trying to upgrade to say Jellybean). If you need more help always ask, but you should be fine. If I lived nearby I'd do it for you.
Click to expand...
Click to collapse
growthweb said:
All I can say is unbelievable help here! Thank you. I am spending hours on this (plus a fortune on this new Tab 2 7). After studying up I do now understand how Odin works and how grabbing the correct firmware will do the job. HOWEVER (maybe others come across this huge roadblock) nothing can be done with out usb interaction. I DID DOWNLOAD KIES and installed it. But no matter what I do can not get any storage device listed or anything going on between tab and computer. Only thing my Tab does is when I plug it in to the computer via usb is go in to charging mode with the charging icon showing. Loading Odin does not show any connection. I have tried different computer USB plugins, 3 different computers (all I have loaded Kies on). Iam sooooooo close. If only while in the POWER BUTTON DOWN ARROW DOWNLOAD MODE and running ODIN on my computer there would be a connection I would be home free and able to flash firmware.
Click to expand...
Click to collapse
How about you just gtalk me, lol. I'll probably reply faster there anyway. deliberation at gmail dot com.
Don't use kies. Install the Samsung driver for mobile phones (Google it).
Sent from my GT-P5113 using Tapatalk 2
Download Mode
growthweb said:
All I can say is unbelievable help here! Thank you. I am spending hours on this (plus a fortune on this new Tab 2 7). After studying up I do now understand how Odin works and how grabbing the correct firmware will do the job. HOWEVER (maybe others come across this huge roadblock) nothing can be done with out usb interaction. I DID DOWNLOAD KIES and installed it. But no matter what I do can not get any storage device listed or anything going on between tab and computer. Only thing my Tab does is when I plug it in to the computer via usb is go in to charging mode with the charging icon showing. Loading Odin does not show any connection. I have tried different computer USB plugins, 3 different computers (all I have loaded Kies on). Iam sooooooo close. If only while in the POWER BUTTON DOWN ARROW DOWNLOAD MODE and running ODIN on my computer there would be a connection I would be home free and able to flash firmware.
Click to expand...
Click to collapse
Once you are in download mode, connect your tab to the computer with the usb connection.....you should see a com xx number pop up in Odin in yellow reporting your device is connected thru a communication port. From there you will be able to choose the file you want as a PDA uncheck everything else...reboot...reset timer....whatever. Just make sure you have the correct firmware. There is a Odin flashback to Stock rom in the development section. Make sure it's for your device. Once you start Odin, should take about 4 mins...disconnect and hold the power button down to reboot. That's it....
Hello Everyone Again, I just want to say thank you for all of you who took the time to help. I hopefully will become knowledgeable enough to help people in the forums as I gain knowledge. I finally did find the solution. I did everything that was mentioned. And no matter what what I did with KIES drivers Samsung usb drivers, etc could not get a connection so I could us Odin to keep me back to the orgiginal 800 mb 4.04 original file. My solution was (as mentioned) I deleted all my windows drivers dealing with usb, kies, etc. Then rebooted. I notice even though I did not have a direct usb connection showing up now Odin was showing a connection! So using Odin I got to restore everything and now back to like new. Lesson learned. Hope this helps others that almost fatally brick their tablets. Thanks again for all our help
growthweb said:
Hello Everyone Again, I just want to say thank you for all of you who took the time to help. I hopefully will become knowledgeable enough to help people in the forums as I gain knowledge. I finally did find the solution. I did everything that was mentioned. And no matter what what I did with KIES drivers Samsung usb drivers, etc could not get a connection so I could us Odin to keep me back to the orgiginal 800 mb 4.04 original file. My solution was (as mentioned) I deleted all my windows drivers dealing with usb, kies, etc. Then rebooted. I notice even though I did not have a direct usb connection showing up now Odin was showing a connection! So using Odin I got to restore everything and now back to like new. Lesson learned. Hope this helps others that almost fatally brick their tablets. Thanks again for all our help
Click to expand...
Click to collapse
Glad you got it sorted.
i jus did the same thing u did
hi how r u doing. i jus did the same mistake u did and i really need your help please
Maxwell255 said:
hi how r u doing. i jus did the same mistake u did and i really need your help please
Click to expand...
Click to collapse
Hi.if u have done the exact same thing then just read the previous page and comments.
Sent from my GT-P3110 using xda app-developers app
Glad to see you resolved your issue. In the future, question/help threads belong in Q&A only.
Thank You.
Because your issue has been resolved...
Thread Closed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"If you choose not to decide, you still have made a choice"
Sent from my Galaxy Note (i717), using XDA Premium.
PeartFan40 said:
Glad to see you resolved your issue. In the future, question/help threads belong in Q&A only.
Thank You.
Because your issue has been resolved...
Thread Closed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"If you choose not to decide, you still have made a choice"
Sent from my Galaxy Note (i717), using XDA Premium.
Click to expand...
Click to collapse
Thread is still actually open, lol
Is there any way to save my tablet if there is NO firmware out?
Im talking about the SCH I705, I followed the root guide, and it got ****ed up.
Unable to boot into recovery (it goes to Odin "could not do normal boot.")
Tablet seems unresponsive sometimes (to power on/off)
Will boot cycle occasionally
???????????????????
igotbricked said:
Is there any way to save my tablet if there is NO firmware out?
Im talking about the SCH I705, I followed the root guide, and it got ****ed up.
Unable to boot into recovery (it goes to Odin "could not do normal boot.")
Tablet seems unresponsive sometimes (to power on/off)
Will boot cycle occasionally
???????????????????
Click to expand...
Click to collapse
You have to reflash your tablet using ODIN. It's not that hard. Just follow the second method here (you don't need to download android SDK)
copy this in your navigator bar : rootzwiki . com/topic/37272-verizonsch-i705-root-for-all-current-firmware/ ( delete space around the dot)
Plus, your tab will be rooted.
You're welcome.
P.S : This limitation of URL is annoying as hell.

Galaxy S3 i9300 Unbrick [restore to stock rom] [noobs][easy]

Hi guys! This is a noob-proof guide on how to flash stock samsung firmware on your i9300. Whether you have bricked it or just want the stock firmware back. Here's how to do it (detailed explaination)
WARNING! : This is only for the GT i9300 (international version) , Check your device before proceeding. Also you might lose all your data. So backup! i am not responsible if you brick your phone(although very unlikely) by not following the guide properly
Also you will lose your custom recovery, Custom ROM and will not longer have root
Ok lets begin!
1. Make sure you have the samsung drivers installed on your pc (http://bit.ly/SDaIIE)
2. Your device should have at least 80% battery left
3. Enable USB Debugging by going to Settings>Developer Options>Tick the Usb debugging tick box!
Files needed :
1. Android 4.1.2 I9300XXEMA1 for Galaxy S3 I9300 - http://bit.ly/10vkxdj
2. Odin 3.07 - http://bit.ly/16aRzF4
Extract The firmware Zip file until you get a file with a .tar extension and some other files. Do not extract furthur
Extract odin zip file till you get Odin3 v3.07.exe
Now here comes the actual flashing part
1. Power off your smartphone. Wait 5-6 seconds for vibration to confirm complete switch off.
2. Now, get into Download Mode by pressing and holding Volume Down, Home and Power button simultaneously until Samsung Galaxy logo appears in phone screen. Wait few seconds and your phone will be in download mode.
3.Open odin as administrator and connect your s3 to your computer with usb cable
4. You will get a message "Added" in the message box in odin and You should also see COM port with a number in Yellow if you successfully added your device.
if you don't get this , try another usb port.. if it still doesn't come , reinstall drivers.
5. Select these files from I9300XXEMA1 folder in Odin at respective buttons:
Click the PDA Button, and select the .tar.md5 file here with *code* appearing in its name
Click the Phone Button, and select file with *modem* in its name (leave if there is no such file)
Click the CSC Button, and select file with *csc* in its name (leave if there is no such file)
Click the PIT Button, and select the .pit file. Use only if you got it while extracting , otherwise ignore it.
6. make sure Auto Reboot and F. Reset Time checkboxes are selected. Also, make sure that Re-Partition checkbox is selected, only if you are using a .pit file
7. Double check everything above and hit start!
8. once flashing is complete the phone will reboot automatically and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can then unplug the USB cable to disconnect your device from computer.
congratz , you have just restored your i9300!
If this has helped you make sure to hit the thanks button!
what have you developed?
We already know Odin, and this doesn't UNBRICK anything
Sent from my GT-I9300 using xda premium
This is so worthy of development thread. ...:banghead:
Sent from my GT-I9300 using xda premium
Helpful post to some,,,,,however the unbrick part is misleading as all this does is flash a stock ROM.
Only soft brick... like any other Samsung device.
Reported not development plus we have all this information already posted .
OP is splattering this post all over the forum .
jje

I9190XXUBNA1 Upgraded to Kitkat Success

hi all,
ive been having fast dormancy issues and i got so annoyed, i decided to take a chance and upgrade to Kitkat.
i have a GT-I9190 S4 Mini, unbranded , supplied by CellC South Africa,
For those with the I9190XXUBNA1 models,
i would like to confirm that the kitkat I9190XXUCNG1 works successfully with no issues on this model.
hope this helps others.
its very laggy for the first 2, 3 minutes. i would suggest you leave the phone for about 10 minutes after the home screen shows up.
i did this with 100% battery life, knox counter has not been tripped btw.
i would like to thank ibtimes.co.uk , i followed the guide from their site.
Im not a reg user on the forum, but i thought i would share this is since ive seen the I9190XXUBNA1 model to have very less info online about them.
How to install I9190XXUCNG1 Android 4.4.2 on Galaxy S4 Mini GT-I9190
Step-1: Extract the downloaded firmware zip using winrar/7zip/winzip or any other extracting tool to get a .tar.md5 file with few other files, which are optional
Step-2: Extract the Odin zip to get Odin3 v.3.09.exe with few other files
Step-3: Switch off the S4 Mini and wait for some time until the device goes off completely
Step-4: Reboot the phone into Download Mode by pressing and holding Home, Power and Volume Down buttons together
Step-5: Run Odin on the computer as an Administrator
Step-6: Connect the S4 Mini to computer using USB cable while it is in Download mode. Wait for some time until Odin detects the device. When the phone is connected successfully an Added message will appear under Odin. Also, the ID: COM box in Odin will turn light blue with COM port number, indicating successful connection
Note: If the Added message does not appear, then try to re-install USB derivers or change the USB port on the computer.
Step-7: In Odin, click the AP button and select the .tar.md5 file which was extracted earlier
Step-8: Enable Auto Reboot and F.Reset Time checkboxes. Ensure that Re-Partition checkbox is not ticked
Step-9: Double check everything then click the Start button in Odin. The installation process should begin now and take about few minutes to complete
Step-10: When the installation process is completed, the phone will restart automatically. Once the home screen appears, disconnect the phone from the computer
Click to expand...
Click to collapse

Fix screen mirroring after root - Android 5.1.1 - Note 10.1 (2014 Edition) P605 LTE

This is for Samsung Galaxy Note 10.1 (2014 Edition) LTE P605 (lt03ltexx)
Could work for rooted P600, p601, and many other Samsung devices with 5.1.1
If this break your phone or neck I'm not responsible. You do it on your own risk. It worked for me.
* If you don't need root, you don't have to do this.
1. Root your device first (with stock ROM)
2. Try Screen Mirroring. (*If screen mirroring worked fine you don't need to do anything.)
3. If screen mirroring failed
a. Use a root explorer.
b. take a backup copy of your build.prop file from \system directory
c. Edit the file and at the end of the file add wlan.wfd.hdcp=disable
d. Save the file
e. Restart the device
Now it should work fine.
There are lots of articles to help you how to root and how to flash stock ROM.
Thanks. Fixed my Samsung Galaxy Note 10.1 (2014 Edition) and Samsung Galaxy S5.
To anybody adding this fix don't overlook line d. Save the file and restart.
You are welcome
You are welcome
Superowl said:
Thanks. Fixed my Samsung Galaxy Note 10.1 (2014 Edition) and Samsung Galaxy S5.
To anybody adding this fix don't overlook line d. Save the file and restart.
Click to expand...
Click to collapse
I posted this in this thread where I originally saw your advice: https://forum.xda-developers.com/ga...-hardware-problem-t2982049/page4#post72866194
But I figured I'd come to your thread too.
So I have a rooted Samsung Galaxy tab S 10, I did this process once and it did not work so I replaced the edited build.prop file with the original I saved. Afterwards I decided to give it another try just in case, this time I cut and pasted wlan.wfd.hdcp=disable, saved, checked it was there, restarted and now my device will not restart. All it will do is display SAMSUNG GALXY TAB S POWERED BY ANDROID and vibrate in a pattern, three quick pulses then one pulse, pause, repeat. I can hard restart it but it only goes to the exact same screen. I can't even shut it down, only restart.
So this is a huge bummer. Is this fixable?
I think something went wrong somewhere. Now on my way to work. I'll help you once I'm back. I think it can be fixed.
sathpra said:
I think something went wrong somewhere. Now on my way to work. I'll help you once I'm back. I think it can be fixed.
Click to expand...
Click to collapse
Thank you, I'm also about to be heading out for a while but I'd love to give anything a try in the morning.
I have since found that I can boot it into Odin mode, but not Recovery mode. I don't know anything about Odin mode, but the only thing I've been able to do from there is get it back to the boot screen I mentioned above. Either way still can't shut it down.
fix your tablet first
brokentablet said:
Thank you, I'm also about to be heading out for a while but I'd love to give anything a try in the morning.
I have since found that I can boot it into Odin mode, but not Recovery mode. I don't know anything about Odin mode, but the only thing I've been able to do from there is get it back to the boot screen I mentioned above. Either way still can't shut it down.
Click to expand...
Click to collapse
Download the latest odin to your windows PC
download your firmware file from http://updato.com/firmware-archive-select-model?q=Samsung+Galaxy+tab+S+10&exact=1
Flash it.
Extract (unzip) the firmware file
Download Odin v3.10.7
Extract Odin ZIP file
Open Odin v3.10.7
Reboot Phone in Download Mode (press and hold Home + Power + Volume Down buttons)
Connect phone and wait until you get a blue sign in Odin
Add the firmware file to AP / PDA
Make sure re-partition is NOT ticked
Click the start button, sit back and wait few minutes​Now your tablet should be working again.
once it is working let me know
sathpra said:
Download the latest odin to your windows PC
download your firmware file from http://updato.com/firmware-archive-select-model?q=Samsung+Galaxy+tab+S+10&exact=1
Flash it.
Extract (unzip) the firmware file
Download Odin v3.10.7
Extract Odin ZIP file
Open Odin v3.10.7
Reboot Phone in Download Mode (press and hold Home + Power + Volume Down buttons)
Connect phone and wait until you get a blue sign in Odin
Add the firmware file to AP / PDA
Make sure re-partition is NOT ticked
Click the start button, sit back and wait few minutes​Now your tablet should be working again.
once it is working let me know
Click to expand...
Click to collapse
This worked, it's restarted and appears to be acting completely normally and my files are intact. Thank you very much.
brokentablet said:
This worked, it's restarted and appears to be acting completely normally and my files are intact. Thank you very much.
Click to expand...
Click to collapse
now you can try
root with CF-Auto-Root
use xplor app you find the file build.prop file from \system directory
look for wlan.wfd.hdcp=disable or wlan.wfd.hdcp=enable
if wlan.wfd.hdcp=enable make it wlan.wfd.hdcp=disable
otherwise add wlan.wfd.hdcp=disable at the end of the file​
don't forget backup your files and do a factory reset before trying this
Many thanks!!!
It works for my samsung s5 and also Tab A 2016.
But how about if the cell phone/tablet is not rooted? I guess not everyone want to loss warranty.

Categories

Resources