Database Users

Cant access mainmenu of servicemode for unlock

Could someone help me out please,
I've tried to unlock my phone but I can't get to the main menu of the service mode.
I accessed *#0011#
tapped menu, select back
tapped menu, select input, inputted 1, ok
waited as well as tapped menu, select back
it doesn't go anywhere or changes menu.
Any ideas?

guitaoo7 said:
Could someone help me out please,
I've tried to unlock my phone but I can't get to the main menu of the service mode.
I accessed *#0011#
tapped menu, select back
tapped menu, select input, inputted 1, ok
waited as well as tapped menu, select back
it doesn't go anywhere or changes menu.
Any ideas?
Click to expand...
Click to collapse
What firmware, modem, rom are you using? Most likely is the modem causing it.

I bought it from eBay but i'm sure those things have not been tampered with.
It is locked onto UK's three mobile network.
It's on I9505XXUBMEA

guitaoo7 said:
I bought it from eBay but i'm sure those things have not been tampered with.
It is locked onto UK's three mobile network.
It's on I9505XXUBMEA
Click to expand...
Click to collapse
The modem doesn't allow to access the service menu. You need XXUAME2 or older modem to get access to service menu.
This thread has all modems available to download.
As for the phone being carrier-locked, I'm not sure how to solve that. All phone sold in my country are unlocked.

so, i cant unlock the phone via the servicemode then?
and since it's carrier locked, i can't downgrade the modem? or can i?

guitaoo7 said:
so, i cant unlock the phone via the servicemode then?
and since it's carrier locked, i can't downgrade the modem? or can i?
Click to expand...
Click to collapse
You can downgrade the modem. This can be done by downloading modem from the thread I told you, and flashing it through Odin.
Edit: Be sure to follow the instructions on how to properly flash modem.

changing the modem will not affect the carrier lock will it?
I'm worried I might not be able to use any sim after changing the modem XD

guitaoo7 said:
changing the modem will not affect the carrier lock will it?
I'm worried I might not be able to use any sim after changing the modem XD
Click to expand...
Click to collapse
If you're scared, you can always do a full system backup using custom recovery. If any problem occurs, just restore the backup.

Also, I just realized i can't find the settings to enable debugging on my S4
Can i still use customer recovery, my phone's not rooted and it boots with the three mobile logo

guitaoo7 said:
Also, I just realized i can't find the settings to enable debugging on my S4
Can i still use customer recovery, my phone's not rooted and it boots with the three mobile logo
Click to expand...
Click to collapse
Custom recovery does NOT need root. It replaces the stock recovery of the phone. Same goes for modem.
Did you have developer options at your settings? If not, go to settings>about device. Press the 'Build Number' 7 or 8 times. (Cannot remember exactly how many times). The developer option will then be available.

yeah, just figured it out. ok i'm going to try it now using ME2 like you said... hopefully nothing bad happens

changed modem and can access menu now. thanks a bunch dude

guitaoo7 said:
changed modem and can access menu now. thanks a bunch dude
Click to expand...
Click to collapse
No problem.
Next time use the search function if possible. There's actually quite alot of threads and posts about this.

lzk123 said:
No problem.
Next time use the search function if possible. There's actually quite alot of threads and posts about this.
Click to expand...
Click to collapse
I have used the search function, but fear is killing me.
wherever I go, I find that the flashing process requires that the phone is unlocked.
can you please let me know how to go about it?
I downloaded the 02 modem firmware now. and Odin, but can't go any further

Hello, sorry to bring back this thread, but I have a weird problem.
I tried every possibility and variants of this unlock method (*#0011#) but nothing changes. It still asks for the network code.
I flashed a ME2 modem, and same thing ..
Is there anything I missed ?

sim unlock after OTA 4.4 update?

hello i was wondering if there is a way to unlock the sim on the xt907 after the kitkat update? i used the exploit to sim unlock this phone before so it could be used on straight talk. my brother updated it to kitkat and now the sim is locked again. is there anyway to redo the process or downgrade back down to jellybean so i can use the exploit again? any help would be awesome.

The procedure is the same you used before. It worked for me.

my copy of cdma workshop 2.7 locks up when i enter the spn and click send? does the phone have to be in regular boot, ap fastboot? cause i dont remember and the video dont say

georgia411 said:
my copy of cdma workshop 2.7 locks up when i enter the spn and click send? does the phone have to be in regular boot, ap fastboot? cause i dont remember and the video dont say
Click to expand...
Click to collapse
Should be in BP Tools Mode.
Video: https://www.youtube.com/watch?v=b7-Kbm1_enM
Guide: http://forum.xda-developers.com/showthread.php?t=2487863

carb0nrain said:
Should be in BP Tools Mode.
Video: https://www.youtube.com/watch?v=b7-Kbm1_enM
Guide: http://forum.xda-developers.com/showthread.php?t=2487863
Click to expand...
Click to collapse
i got it in bp mode and when i enter the spc it freezes up but i can connect the phone via port fine just when i send the code i locks up

georgia411 said:
i got it in bp mode and when i enter the spc it freezes up but i can connect the phone via port fine just when i send the code i locks up
Click to expand...
Click to collapse
Are you sending the code "000000" (6 zeros)? I actually just unlocked mine successfully. I didn't use any of the downloads that he gave. I used the demo of CDMA Workshop (currently v3.9.0) and the drivers package from motorola's website. Try using those. It appeared to work for me.

carb0nrain said:
Are you sending the code "000000" (6 zeros)? I actually just unlocked mine successfully. I didn't use any of the downloads that he gave. I used the demo of CDMA Workshop (currently v3.9.0) and the drivers package from motorola's website. Try using those. It appeared to work for me.
Click to expand...
Click to collapse
yes just tried with 3.9.0 and say device does not answer

georgia411 said:
yes just tried with 3.9.0 and say device does not answer
Click to expand...
Click to collapse
Is usb debugging enabled? Also list all the steps used to replicate the problem.

240
carb0nrain said:
Is usb debugging enabled? Also list all the steps used to replicate the problem.
Click to expand...
Click to collapse
i had tried another tutorial on downgrading that involved flashing the boot.img so i downloaded the kitkat files from moto and got that all fixed.
ive got the phone in bptools
i start workshop 3.9.0
it connects to the com port
i click secuirty and enter six 0's and it says device fails to answer

georgia411 said:
i had tried another tutorial on downgrading that involved flashing the boot.img so i downloaded the kitkat files from moto and got that all fixed.
ive got the phone in bptools
i start workshop 3.9.0
it connects to the com port
i click secuirty and enter six 0's and it says device fails to answer
Click to expand...
Click to collapse
Hmmm. That is interesting. The only thing that i can think of is your QC diagnostic driver may be corrupted somehow? Did you follow the video tutorial (https://www.youtube.com/watch?v=mm2NKdXdHnc) to install it? Also can you post a screenshot with your device manager open while your phone is connected in bp tools mode. In you device manager expand the "Other Devices" tab.

carb0nrain said:
Hmmm. That is interesting. The only thing that i can think of is your QC diagnostic driver may be corrupted somehow? Did you follow the video tutorial (https://www.youtube.com/watch?v=mm2NKdXdHnc) to install it? Also can you post a screenshot with your device manager open while your phone is connected in bp tools mode. In you device manager expand the "Other Devices" tab.
Click to expand...
Click to collapse
im gonna try reinstalling the drivers, i forgot how to delete them though do you know the location cause they arent under installed programs

georgia411 said:
im gonna try reinstalling the drivers, i forgot how to delete them though do you know the location cause they arent under installed programs
Click to expand...
Click to collapse
Under installed programs, look for a name that begins with Motorola. Good Luck. If it isn't under installed programs, then I don't think they are installed. If so, go grab the official drivers from here: http://www.mymotocast.com/download/MDM?platform=windows

carb0nrain said:
Under installed programs, look for a name that begins with Motorola. Good Luck. If it isn't under installed programs, then I don't think they are installed. If so, go grab the official drivers from here: http://www.mymotocast.com/download/MDM?platform=windows
Click to expand...
Click to collapse
ok thanks for all the help, i think ive made progress. i switched the cable i was using with my brothers razr m with my blu studio 5.3s cable and loaded up cdma workshop 2.7 and i was able to do all the steps. another issue i found is the other cable wasnt letting me install the qc interface. so now i gotta wait for him to come over and put in his straight talk sim and hopefully we are back in business with it . ill let you know how it goes when hes able to come over
thanks again

georgia411 said:
ok thanks for all the help, i think ive made progress. i switched the cable i was using with my brothers razr m with my blu studio 5.3s cable and loaded up cdma workshop 2.7 and i was able to do all the steps. another issue i found is the other cable wasnt letting me install the qc interface. so now i gotta wait for him to come over and put in his straight talk sim and hopefully we are back in business with it . ill let you know how it goes when hes able to come over
thanks again
Click to expand...
Click to collapse
No problem, glad I was able to help. Have a good rest of your day. Hopefully everything works out.

thanks, much and you have a good one as well.
just to recap for anyone else having this issue here goes what was wrong.
the issue: droid razr m xt907 on straight talk updated to 4.4 and service was lost
first thing make sure all your drivers are installed. in you have the phone plugged in and you dont see QC Interface then uninstall all and reference the links listed above in the other replies (or i may have them listed if i edit)
now make sure your usb cable is working, the one for this phone would not work properly for this so the blu studio 5.3s cable worked great. make sure you have cdma workshop and the spn code is "000000" aka six zeros.
follow all the steps in the tutorial and you should be up and running. this phone does work on straight talk if you follow the tutorial.

carb0nrain said:
No problem, glad I was able to help. Have a good rest of your day. Hopefully everything works out.
Click to expand...
Click to collapse
hey buddy i put the sim card in today and it wont work i done everything by the tutorial and it writes the file. when the phone restarts if i do a network search it shows ATT but it will not connect. any ideas?

georgia411 said:
hey buddy i put the sim card in today and it wont work i done everything by the tutorial and it writes the file. when the phone restarts if i do a network search it shows ATT but it will not connect. any ideas?
Click to expand...
Click to collapse
Yeah, I think the problem is that it knows that its ATT but it doesn't know what to do with the connection. You probably have to set a manual APN setting. Go to Settings-->Wireless&Networks-->More-->Mobile Networks-->Access Point Names-->Add Button(Upper Right Corner)
Use the following values:
NAME: (type anything you like, this doesn't matter. Use "AT&T Phone" or "My Phone", something like that. Just remember that every access point you create should have a different name.)
APN: wap.cingular
Proxy: (not set)
Port: (not set)
Username: [email protected]
Password: CINGULAR1
Server: (not set)
MMSC: http://mmsc.cingular.com
MMS Proxy: wireless.cingular.com
MMS port: 80
MCC: 310
MNC: 410
Authentication Type: (not set)
APN type: (not set)
APN protocol: IPv4
APN: enabled (may need to check this, not sure about your model)
Bearer: unspecified
*DOUBLE CHECK SPELLING*
These values may not work. They were just the first ones i saw. If they don't work, then i will look for a new set of values.
If they dont work, also try the same settings with the username and password blank
When its added make sure you click on it in the access point names list.
Also go back from the access names list and make sure your "Prefferred Network Type" is set to Global.
Hopefully this works for you.

Does GSM mode with APN settings still work in 4.4.2
I have a Verizon RAZR M running on stock 4.1.2 + root + Xposed. I am using a GSM sim on my phone and I'm getting HSPA+ data (so I guess my phone is "unlocked" as I can use another carrier).
My question is does the 4.4.2 ROM support GSM mode and can we add/edit apn in the 4.4.2 rom?

You can edit/add APNs on 4.4.2 and I'm pretty sure you can use GSM on a 4.4.2 ROM.
Sent from my DROID RAZR M using XDA Free mobile app

Razr M Kitkat Straight Talk AT&T sims
I updated to KitKat 4.4.2. and my service stopped. I used Radiocomm to set the NV to 00. I failed at least three times. You have to enable developer options, usb debugging and boot up in Factory mode. Follow the instruction that have been poster on this form = http://forum.xda-developers.com/showthread.php?t=2166542 After I changed the NV I always pressed the restart button. After the phone has rebooted, unplug it and turn it off. Close Radiocomm and open Radiocomm up again. Boot phone back up in Factory mode and connect back usb to Radiocomm. Read the NV again. If it still 00, it has worked. Radiocomm, like people have said, will not see your phone unless usb debugging and Factory mode have not been set. My only complaint is that JB worked prefect and KK has the "Modem Fast Dormancy Monitor Service" screw up. Me and my wifes phone both are effected by this. Our JB battery life was real good. Now we both have reboots 2 or 3 times a day. My battery was dead one morning. I have found no help for this. Good luck with your phone. My Straight Talk AT&T service is really good. Fast Dormancy errors will make me buy some another phone unless Motorola issues a fix. I'm not going to hold my breathe!

[Q] [SOLVED] 900w8 No Service

Hi there
Recently I encountered some issues with my Note 3. google playstore did not allow me to sign in and no notifications appeared on my screen (the phone has root, and TWRP). I decided to try out CM11, downloaded it from the original site along with gapps on my internal sd. i wiped data cache .. the usual and installed the two files except they did not do anything. I download the custom recovery 1.3gb file using odin. booted up and noticed that my service is not working. i called my service provider to see if the problem was on their end but wasnt. i factory reset the phone via settings... same problem. i went into recovery wiped data and cache booted up and same issue.
IMEI= has not been blacklisted
I occasionally do see bars appear however no change in service status
I tried flashing TWRP again and installing CM11 except i get a "failed" message "unable to mount"
I sure hope I did not kill this phone
any idea how do i get service back on my phone? everything else on the phone works besides service provider....
Thank you very much!!

Not sure if this means anything ...

When you had it working with a Touchwiz Rom it could have been your APN settings that were not allowing you to get signal.
If I were you I would start fresh and download the factory image from sammobile and flash it again using Odin. We can start troubleshooting from there.
Did you use this tutorial to get a custom recovery installed? Its really straightforward and I recommend this method over all others.
http://forum.xda-developers.com/showthread.php?t=2792819

RacecarBMW said:
When you had it working with a Touchwiz Rom it could have been your APN settings that were not allowing you to get signal.
If I were you I would start fresh and download the factory image from sammobile and flash it again using Odin. We can start troubleshooting from there.
Did you use this tutorial to get a custom recovery installed? Its really straightforward and I recommend this method over all others.
http://forum.xda-developers.com/showthread.php?t=2792819
Click to expand...
Click to collapse
I followed the steps exactly and I got this error.

MacProo said:
I followed the steps exactly and I got this error.
Click to expand...
Click to collapse
1. Check for Reactivation Lock
2. Check that you are NOT downgrading your bootloader.
EDIT: You are downgrading your bootloader, or else you wouldn't get the aboot fused 2 > binary 2 error.
You will have to flash stock, go to http://www.sammobile.com/firmwares/3/?download=26660
Flash that in AP of Odin. Then you will be reverted back to stock.

nicholaschum said:
1. Check for Reactivation Lock
2. Check that you are NOT downgrading your bootloader.
EDIT: You are downgrading your bootloader, or else you wouldn't get the aboot fused 2 > binary 2 error.
You will have to flash stock, go to http://www.sammobile.com/firmwares/3/?download=26660
Flash that in AP of Odin. Then you will be reverted back to stock.
Click to expand...
Click to collapse
I downloaded that file, used ODIN V3.09 selected the file under AP. the flash worked. bootloader version NB7 however I still do not get any service
i know the issue is not SIM card related. I swapped it to another phone and received service

MacProo said:
I downloaded that file, used ODIN V3.09 selected the file under AP. the flash worked. bootloader version NB7 however I still do not get any service
i know the issue is not SIM card related. I swapped it to another phone and received service
Click to expand...
Click to collapse
You might have to set up your APN settings after you have done that. You can google the APN settings for your carrier and then put them in manually by going Settings > Connections > More Networks > Mobile Networks > Access Point Names
You'll be able to add them in there.

MacProo said:
I downloaded that file, used ODIN V3.09 selected the file under AP. the flash worked. bootloader version NB7 however I still do not get any service
i know the issue is not SIM card related. I swapped it to another phone and received service
Click to expand...
Click to collapse
Is your IMEI (*#06#) a real IMEI that matches with the values at the back of your phone, and not just null/null?

nicholaschum said:
Is your IMEI (*#06#) a real IMEI that matches with the values at the back of your phone, and not just null/null?
Click to expand...
Click to collapse
*#06# gives me a matching IMEI with the back of the phone

MacProo said:
*#06# gives me a matching IMEI with the back of the phone
Click to expand...
Click to collapse
Put your SIM in your phone, download Advanced Signal Status from the Play Store, and show us some screenshots.
In this menu you get to see more information about what is going on with your network.
Have you also made sure your APN settings are set correctly?

RacecarBMW said:
You might have to set up your APN settings after you have done that. You can google the APN settings for your carrier and then put them in manually by going Settings > Connections > More Networks > Mobile Networks > Access Point Names
You'll be able to add them in there.
Click to expand...
Click to collapse
nicholaschum said:
Put your SIM in your phone, download Advanced Signal Status from the Play Store, and show us some screenshots.
In this menu you get to see more information about what is going on with your network.
Have you also made sure your APN settings are set correctly?
Click to expand...
Click to collapse
I compared APN setting between my two devices (both are the same carrier and same model of phone ((borrowing from someone)). APN settings were the same except APN Protocol and APN roaming protocol were dark and could not be changed. even though i couldn't change it it was still listed as ipv4 same as the working phone.
If you need any other information, please let me know

MacProo said:
I compared APN setting between my two devices (both are the same carrier and same model of phone ((borrowing from someone)). APN settings were the same except APN Protocol and APN roaming protocol were dark and could not be changed. even though i couldn't change it it was still listed as ipv4 same as the working phone.
If you need any other information, please let me know
Click to expand...
Click to collapse
Any other suggestions? the phone is still dead

You could try resetting the nvram. Check my thread here: http://forum.xda-developers.com/showthread.php?t=2754957
My thread is for the 900t, but it should be the same for your model.
Sent from my leanKernel 3.4 powered stock 4.4.2 (NF1) SM-N900T

toastido said:
You could try resetting the nvram. Check my thread here: http://forum.xda-developers.com/showthread.php?t=2754957
My thread is for the 900t, but it should be the same for your model.
Sent from my leanKernel 3.4 powered stock 4.4.2 (NF1) SM-N900T
Click to expand...
Click to collapse
I gave that a try, rebooted the phone, attempted a call and "Not registered on network"
would changing the ROM have any impact on the service for whatever reason? i gave CM11 a try but wouldn't instal.

Seeing all that you've tried, the one thing i don't see tried is the sim card. Have you tried your sim in another phone, or another known good sim in yours? The fact it gets signal but doesn't register with the network makes me think the sim had somehow gotten corrupted.
Sent from my leanKernel 3.4 powered stock 4.4.2 (NF1) SM-N900T

toastido said:
Seeing all that you've tried, the one thing i don't see tried is the sim card. Have you tried your sim in another phone, or another known good sim in yours? The fact it gets signal but doesn't register with the network makes me think the sim had somehow gotten corrupted.
Sent from my leanKernel 3.4 powered stock 4.4.2 (NF1) SM-N900T
Click to expand...
Click to collapse
That'd be a bit weird, but yeah you should ask your friend's phone to try your SIM card.

nicholaschum said:
That'd be a bit weird, but yeah you should ask your friend's phone to try your SIM card.
Click to expand...
Click to collapse
As of right now I am borrowing a friends phone (also a 900w8) with my SIM card and everything seems to be working
If anyone has ANY suggestions I'm willing to give that a try.
I appreciate everyones suggestions and help!

toastido said:
Seeing all that you've tried, the one thing i don't see tried is the sim card. Have you tried your sim in another phone, or another known good sim in yours? The fact it gets signal but doesn't register with the network makes me think the sim had somehow gotten corrupted.
Sent from my leanKernel 3.4 powered stock 4.4.2 (NF1) SM-N900T
Click to expand...
Click to collapse
The SIM does work on another phone.

MacProo said:
The SIM does work on another phone.
Click to expand...
Click to collapse
I'm not sure then. hopefully someone can come in from here.... sorry man, best of luck!
Sent from my leanKernel 3.4 powered stock 4.4.2 (NF1) SM-N900T

toastido said:
I'm not sure then. hopefully someone can come in from here.... sorry man, best of luck!
Sent from my leanKernel 3.4 powered stock 4.4.2 (NF1) SM-N900T
Click to expand...
Click to collapse
Thank you!
nicholaschum said:
1. Check for Reactivation Lock
2. Check that you are NOT downgrading your bootloader.
EDIT: You are downgrading your bootloader, or else you wouldn't get the aboot fused 2 > binary 2 error.
You will have to flash stock, go to http://www.sammobile.com/firmwares/3/?download=26660
Flash that in AP of Odin. Then you will be reverted back to stock.
Click to expand...
Click to collapse
Would trying your method (http://forum.xda-developers.com/showthread.php?t=2792819) but changing the bootloader to NB7 work?
"If your bootloader is of version NA2 (somehow) or NB7, skip to the contents of Step 4," rather than proceeding to step 4 going to step 1?

[Q] Nexus 4 Lollipop 5.1 How do I enable LTE 4G

I updated to stock 5.1 from 5.0.2 yesterday. Prior to this I had LTE 4G on T-Mobile. Now I'm back to 3G . Does anyone else have this experience? and are ther any solutions out there I could use?
I'd value any input or advice on this issue.
Thanks

I tried too to revert 4g on my 5.1 n4 but after i wiped everything ( excepting system ... ) i got a lovely bsod ( blank screen of death ) i don't think is a sollution yet , if i done something wrong someone please explain us how to get it properly back w/o probs , wait for some ideas thanks .

You'll obviously need to be sure the hybrid modem is installed. Beyond that as I recall, I had to "force" it to see the LTE network by dialing *#*#4636#*#* and selecting "LTE only" for the connection. After that I was able to set it to "LTE/GSM auto" and it has worked correctly since.

jherbold said:
You'll obviously need to be sure the hybrid modem is installed. Beyond that as I recall, I had to "force" it to see the LTE network by dialing *#*#4636#*#* and selecting "LTE only" for the connection. After that I was able to set it to "LTE/GSM auto" and it has worked correctly since.
Click to expand...
Click to collapse
I tried that but it did not offer the ability to make that change. I could on 5.0.2. I'm not sure where to get the hybrid modem? any Ideas would be helpful. also does anyone know which hybrid modem to use for T-mobile? Thanks

Go to settings -> About Phone
The Android software version number and baseband (modem) version will be listed. If the last 2 digits of the baseband version is greater than 33, you will not have LTE capability.
https://play.google.com/store/apps/details?id=me.bpear.makomodem

jherbold said:
Go to settings -> About Phone
The Android software version number and baseband (modem) version will be listed. If the last 2 digits of the baseband version is greater than 33, you will not have LTE capability.
https://play.google.com/store/apps/details?id=me.bpear.makomodem
Click to expand...
Click to collapse
Thanks for the reply and info.
I did check that, but I'm not clear what you mean when you refer the Baseband Version last 2 digits
I also have that App installed and it does how seem to work with 5.1 It does not look like its been updated recently
any Ideas?

jherbold said:
You'll obviously need to be sure the hybrid modem is installed. Beyond that as I recall, I had to "force" it to see the LTE network by dialing *#*#4636#*#* and selecting "LTE only" for the connection. After that I was able to set it to "LTE/GSM auto" and it has worked correctly since.
Click to expand...
Click to collapse
Thank you man , you are the best , i followed your instructions , flashed the latest modem from the app (1.03 + 0.33 LTE Hybrid Modem) then enabled LTE Only in test menu , that was , thanks againd , already pressed the button , next time i give a beer

Are there instructions on how to apply the appropriate modem type and such?

marioc89 said:
Are there instructions on how to apply the appropriate modem type and such?
Click to expand...
Click to collapse
Download: https://drive.google.com/file/d/0B77BTW0zStYCS2JPNG1kNnNIamM/view?usp=sharing (LTE Enabler 2.13)
Reboot to Recovery and flash above LTE .zip
Reboot
Done

I'm sorry for being a little slow on this, but when you say reboot to recovery, what do you mean exactly? I have the file downloaded though. Is this a hack or is this something that was made for this phone by Google? I guess what I'm asking is, could I screw up my phone from doing this and if I do, can I revert back to where I had it prior to this if it doesn't work or don't like it?

marioc89 said:
I'm sorry for being a little slow on this, but when you say reboot to recovery, what do you mean exactly? I have the file downloaded though. Is this a hack or is this something that was made for this phone by Google? I guess what I'm asking is, could I screw up my phone from doing this and if I do, can I revert back to where I had it prior to this if it doesn't work or don't like it?
Click to expand...
Click to collapse
I guess you are asking the same questions in 2 threads. Download the enabler listed above to your pc.
Start up the Nexus Root Tool Kit
Connect your phone via usb
Then use the advance options and flash the filefrom your pc to your phone
I hope this helps Let meknow how it goes

marioc89 said:
I'm sorry for being a little slow on this, but when you say reboot to recovery, what do you mean exactly? I have the file downloaded though. Is this a hack or is this something that was made for this phone by Google? I guess what I'm asking is, could I screw up my phone from doing this and if I do, can I revert back to where I had it prior to this if it doesn't work or don't like it?
Click to expand...
Click to collapse
To help your self out It might be useful if you read the post from the following link http://forum.xda-developers.com/showpost.php?p=60115195&postcount=771
It will help you understand the whole process and how to do it. It will also give you lots of background on the issue.
To perform the "Flash" I use the Nexus Root Toolkit. which can be found here.
I hope this helps you. Let us know how it goes

This is perfect! Thank you!
I'm noticing that the settings done keep after a reboot. I don't have to reflash the modem, but I do have to go back into the 4636 settings to re-enable LTE. I've heard this might be fixable in the build.prop? Any thoughts?

ariesgodofwar said:
Download: https://drive.google.com/file/d/0B77BTW0zStYCS2JPNG1kNnNIamM/view?usp=sharing (LTE Enabler 2.13)
Reboot to Recovery and flash above LTE .zip
Reboot
Done
Click to expand...
Click to collapse
Can I do this straight from the phone or from a laptop? And what zip app do I open it with?

marioc89 said:
Can I do this straight from the phone or from a laptop? And what zip app do I open it with?
Click to expand...
Click to collapse
You do it straight from your phone. Download the file, boot into your Recovery, go to the folder you saved the file in (likely in your "Downloads" folder, and just flash the .zip file from your Phone's recovery, and it will do all the necessaries.

It worked flawlessly when I flashed that zip from recovery. All relevant settings changed from 3G to 4G and HSPA to LTE. Speed went from 10 to 36mbps (Telus Canada). ROM is 5.1.1 LMY48T

Hjicons said:
It worked flawlessly when I flashed that zip from recovery. All relevant settings changed from 3G to 4G and HSPA to LTE. Speed went from 10 to 36mbps (Telus Canada). ROM is 5.1.1 LMY48T
Click to expand...
Click to collapse
Did you flash from a custom recovery, twrp or cwm, or stock recovery ?
Sent from my Nexus 6 using Tapatalk

trent999 said:
Did you flash from a custom recovery, twrp or cwm, or stock recovery ?
Sent from my Nexus 6 using Tapatalk
Click to expand...
Click to collapse
TWRP. BTW I tried different hybrid modems with "Nexus 4 Modem Flasher" app without any success.

ariesgodofwar said:
Download: https://drive.google.com/file/d/0B77BTW0zStYCS2JPNG1kNnNIamM/view?usp=sharing (LTE Enabler 2.13)
Reboot to Recovery and flash above LTE .zip
Reboot
Done
Click to expand...
Click to collapse
Thanks that got almost work for me but it says its for android 5.1+ and I am on android 6.0.1 aosp ROM.
But after that I flashed this and bingoo. I can use LTE only in Android 6.
Used this http://www.mediafire.com/?2thymqa7fiiyrqy
Now I can able to click on 'only LTE' from phone info
And it stays at LTE only.
Before this when I goto phone info and it got gsm or wcdma even I click on LTE now its working for me.
I found that zip file from anywhere else I don't know where so I had uploaded and shared here.

Here is what I found about version check. Give it a try if you wish
a) expand nexus-4-lte-enabler-v2.13.zip
b) edit META-INF\com\google\android\updater-script
c) replace 5.1 with 6.0.1 in this line
( is_substring("5.1", file_getprop("/system/build.prop","ro.build.version.release")) )
d) update zip with new file
e) flash zip
Sent from my Nexus 6 using Tapatalk

Set radio band to USA in the testing menu (*#*#4636#*#*) and I can't 2G/3G signal!

I was just trying to get a good signal on 4G and carelessly tapped on the USA band option in "change radio band" in the testing menu as mentioned above. Please help me with this as I don't have a good 4G signal where I live (India, if that's relevant), and calls keep dropping.

Solve
thealonso said:
I was just trying to get a good signal on 4G and carelessly tapped on the USA band option in "change radio band" in the testing menu as mentioned above. Please help me with this as I don't have a good 4G signal where I live (India, if that's relevant), and calls keep dropping.
Click to expand...
Click to collapse
I have the same problem. You have flashing stock again. It's only way.

QZmichal said:
I have the same problem. You have flashing stock again. It's only way.
Click to expand...
Click to collapse
Did you get the issue resolved?

Solve
thealonso said:
Did you get the issue resolved?
Click to expand...
Click to collapse
Yes, this is a solution to the problem.
Remember never set radio band to USA.

Is it possible to fix this by flashing only the modem file?

QZmichal said:
Yes, this is a solution to the problem.
Remember never set radio band to USA.
Click to expand...
Click to collapse
Could you please tell me in detail how you did it? I really need some help with this issue.

Mayby
pijes said:
Is it possible to fix this by flashing only the modem file?
Click to expand...
Click to collapse
Maybe, but with access to the root. Flashing the original software does not require unlocked bootloader.

QZmichal said:
Yes, this is a solution to the problem.
Remember never set radio band to USA.
Click to expand...
Click to collapse
Could I just the take the phone to the service centre? They can fix it without any hassle I suppose?

Answer
thealonso said:
Could I just the take the phone to the service centre? They can fix it without any hassle I suppose?
Click to expand...
Click to collapse
They may provide such services. You can fix it yourself (It takes me than 10 minutes), but if you have concerns it's better to do it for someone with experience.
Regards.

QZmichal said:
They may provide such services. You can fix it yourself (It takes me than 10 minutes), but if you have concerns it's better to do it for someone with experience.
Regards.
Click to expand...
Click to collapse
I'll visit the service centre first and check if they can fix it. If they can't I'll PM you, because I'll need some help through the process. I couldn't even find how to download the image from Github LOL.

QZmichal said:
Maybe, but with access to the root. Flashing the original software does not require unlocked bootloader.
Click to expand...
Click to collapse
I did flash the modem on my old droid maxx without root. It was done using fastboot commands.
If you don't mind losing all your files, I recommend flashing the stock 6.0 completely. Sometimes service center does this too and they don't care about your data assuming you already backed up everything.

Moto X pure edition XT1575 model has same issue
pijes said:
I did flash the modem on my old droid maxx without root. It was done using fastboot commands.
If you don't mind losing all your files, I recommend flashing the stock 6.0 completely. Sometimes service center does this too and they don't care about your data assuming you already backed up everything.
Click to expand...
Click to collapse
Hi
I recently bought MOTO X pure edition XT1575 from US and i changed the radio band to USA accidental.
Now in India its not showing up any network. Its not detecting any cellular network. Could you please help me to fix the issue.

vickyy2 said:
Hi
I recently bought MOTO X pure edition XT1575 from US and i changed the radio band to USA accidental.
Now in India its not showing up any network. Its not detecting any cellular network. Could you please help me to fix the issue.
Click to expand...
Click to collapse
Take out sim
Code:
fastboot erase modemst1
Fastboot erase modemst2
Fastboot erase cache
Insert sim

bablu048 said:
Take out sim
Code:
fastboot erase modemst1
Fastboot erase modemst2
Fastboot erase cache
Insert sim
Click to expand...
Click to collapse
Hi
Thanks for the reply. Could you please elaborate more on what needs to be done. where to execute those commands. I am not familiar with andriod configs. moreover what are the softwares we need to use to do this fastboot

vickyy2 said:
Hi
Thanks for the reply. Could you please elaborate more on what needs to be done. where to execute those commands. I am not familiar with andriod configs. moreover what are the softwares we need to use to do this fastboot
Click to expand...
Click to collapse
1- install this http://forum.xda-developers.com/showthread.php?t=2317790 on your pc
2- phone-settings-[tap on build no 7 times to enable developer settings]- go bacck to settings---you'll see developer settings
3- enable ''''adb debugging''' in developer settings
4- connect phone to pc and run 'minimal fastboot that you installed'
Code:
adb devices
accept the prompt on your device to allow adb, now you should be able to see your device
5-take out sim
6- switch off phone. press '''''''vol[down]+power'''''' to boot into bootloader--connect to PC
7- now run those commands and reboot

bablu048 said:
1- install this http://forum.xda-developers.com/showthread.php?t=2317790 on your pc
2- phone-settings-[tap on build no 7 times to enable developer settings]- go bacck to settings---you'll see developer settings
3- enable ''''adb debugging''' in developer settings
4- connect phone to pc and run 'minimal fastboot that you installed'
Code:
adb devices
accept the prompt on your device to allow adb, now you should be able to see your device
5-take out sim
6- switch off phone. press '''''''vol[down]+power'''''' to boot into bootloader--connect to PC
7- now run those commands and reboot
Click to expand...
Click to collapse
I couldn't locate the adb settings in my phone. after enabling the developer options.
My phone uses Andriod 6.0 mashmellow

vickyy2 said:
I couldn't locate the adb settings in my phone. after enabling the developer options.
My phone uses Andriod 6.0 mashmellow
Click to expand...
Click to collapse
its in developer options

bablu048 said:
its in developer options
Click to expand...
Click to collapse
Hi I did the same way you mentioned and it worked for me , thanks for your guidance and timely help

bablu048 said:
1- install this http://forum.xda-developers.com/showthread.php?t=2317790 on your pc
2- phone-settings-[tap on build no 7 times to enable developer settings]- go bacck to settings---you'll see developer settings
3- enable ''''adb debugging''' in developer settings
4- connect phone to pc and run 'minimal fastboot that you installed' accept the prompt on your device to allow adb, now you should be able to see your device
5-take out sim
6- switch off phone. press '''''''vol[down]+power'''''' to boot into bootloader--connect to PC
7- now run those commands and reboot
Click to expand...
Click to collapse
will this work on moto x force? I did the same thing and am not getting any network. regretting the mistake for almost a month. HELP.

I recovered 2G/3G in Moto G5, here are revised recovery instructions step-by-step for dummies
Original posts by bablu048: post#13 & post#15
Big Thanks to bablu048 !!!
read here
Recovering 2G/3G after Set Radio band to USA in the hidden Testing menu (*#*#INFO#*#*)