Database Users

i9505 updated to 4.3 now recovery booting

Hi i have tried to recover i9505 which was stuck on samsung logo assumed its just like another samsung phone so i downloaded any 4.3 firmware from internet and updated it using odin. Now phone is stuck at samsung logo with a message on top left corner recovery booting... I have tried different firmwares on it some of the were 4.3 but it still stuck there. on some firmware it gives error on odin and doesn't go further
state of the phone
can't boot into recovery holding vol + home +power
phone can go in to download mode
knox kernel lock: 0x0
knox warranty void: 0x1
csb-config-lsb: 0x30
write protection enabled
emmc Burst mode enabled
please help thanks

faisal_sherry said:
Hi i have tried to recover i9505 which was stuck on samsung logo assumed its just like another samsung phone so i downloaded any 4.3 firmware from internet and updated it using odin. Now phone is stuck at samsung logo with a message on top left corner recovery booting... I have tried different firmwares on it some of the were 4.3 but it still stuck there. on some firmware it gives error on odin and doesn't go further
state of the phone
can't boot into recovery holding vol + home +power
phone can go in to download mode
knox kernel lock: 0x0
knox warranty void: 0x1
csb-config-lsb: 0x30
write protection enabled
emmc Burst mode enabled
please help thanks
Click to expand...
Click to collapse
Hi there,
First try getting into recovery again!
Turn device off completely and leave for a minute or so......
Hold Power + Volume Up (no need for home button)
Wait for Vibration and Samsung Logo to appear then the writing in the top left corner....
Release the Power button but keep Volume Up pressed
Wait for Vibration and Samsung logo and writing to appear then let go of the volume rocker
Hopefully will boot to recovery
Factory reset the device and reboot......
If above fails try below............
You need to flash the latest firmware for your device........Which must be 4.3 firmware due to the KNOX boot loader you have, which if you did not know you have void your KNOX warranty 0x1 ( you cannot use the knox application anymore and this is currently irreversible ). Check what the latest firmware is HERE and flash through odin........If your phone is in boot loop after flashing or stuck at the logo then boot into recovery (if possible) and factory reset the device and re-boot.
Flashing any old firmware won't work

Plz Help Reactivation Mode Omega Rom

hello ,
I started rebot to recovery from omega rom.
Now everytime i turn on my phone it will boot into recovery mode but reactivation mode is enable.
Keep showing me custom binary blocked by reactiviation lock and triangle logo below.
In the download mode reactivation lock is on.
what can i do?
plz need help
thx

[Q] Help please. Verizon Note 3 stuck in Recovery Booting

I have JasminRom installed v5.01 or v5.02. I was trying to do Xposed install and tried to install the latest TWRP. TWRP was version 4.4.? So I realized that it was the wrong version too late.
When I power on the phone, it goes to the
Recovery Booting...
Recovery is not seandroid enforcing
then it says
Secure Fail: Recovery.
System software not authorized by Verizon Wireless has been found on your phone.
It displays the above messages when I boot via the power button or do volume up/home/power.
When I hold down/home and power to boot I the boot menu "Volume up: Continue and Volume down: Cancel.
Volume up gives me the ODIN Mode, product name: SM=N900V. Current Binary: Samsung Official. System status: Custom. Reactivation Lock: off. qualcom seucreboot: Enable. Secure download enable.
UDC START.
Downloading...Do not turn off target!!
I had safestrap installed, but it would never boot to it.
I cannot get to safestrap thus to load anything.
With Lollipop 5, I don't think I can use Odin.
How do I recover from this mess up?

I just ODIN over: FLASH N900VVRUEOB6_PartialFirmware.tar.md5 via Odin in AP slot
and it seems to have fixed it, thank God.
Need to install the latest Jasmin now with Xposed... Hope it works.

G900H Can't boot up after change boot logo

Sorry for my bad english
I try to change custom boot splash logo. but, after reboot recovery my phone does not appear the logo and can't boot or recovery mode and can to download mode only.
Product: SM-G900H
System status:Custom
Binary:Custom
Scure download:Enabled (blue color)
Knox wareanty Void:1
RP SWREV: A1
please help me

Set Warranty Bit: Recovery and Set Warranty Bit: Kernel

Hello,
A few months ago my younger brothers SM-G900I had the classic problem of receiving an update that resulted in the device booting the displaying "Set Warranty Bit:Kernel."
Recently my brother asked me to try fix it. When I tried to boot to recovery mode to fix this I saw the normal "Booting recovery mode" but below that I also saw "Set Warranty Bit: Recovery," This then results in recovery mode not booting and going back to the normal black screen and nothing happening ordeal.
At the time of this happening I have been told by my farther that he booted into recovery mode and did a full system wipe
After doing that wipe the phone hasn't since booted into Recovery mode, I believe that there's nothing I can do to fix the phone due to Recovery mode not booting which means I can't use ODIN to fix the "Set Warranty Bit:Kernel" as I can't go into download mode.
If there is anything I can do please let me know many thanks, Xavier1501

ODIN is separate from recovery, and you don't need to launch it from recovery.
Vol up + Home + Power = Recovery
Vol down + Home + Power = ODIN