I recently was attempting to downgrade my kernal so I could root my S5. I knew to this and I'm not sure where I messed up. My phone is stuck in a bootloop. I've tried multiple times to reset through ODIN to stack firmware. This is what it reads. Please help if you can.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900VVRU1ANCG_G900VVZW1ANCG_G900VVRU1ANCG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Download odin for your device, and a official samsu rom md5 for your device.
Put the original rom to your device with odin, but first enter in Download mode ( volume - with home button and power pressed in same time.)
necromisty said:
Download odin for your device, and a official samsu rom md5 for your device.
Put the original rom to your device with odin, but first enter in Download mode ( volume - with home button and power pressed in same time.)
Click to expand...
Click to collapse
I've done that, I've tried three versions of Odin and Five different versions of ROM.
Bootloader is locked, search the forum for tutorials for your model S5 (Verizon?)
Related
When I want to put the PDA file in Odin3 to restore the phone because it does not start I get this error message on the phone "firmware upgrade and tell them issue. Please select recovery mode in kies and try again" I can not use Kies for it is that I entering the wrong model and when I put the PDA file in Odin3 then I FAIL! continuously
HTML:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUFNC5_I9505HTSFNB1_I9505XXUFNC5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
I bet you did a full wipe in recovery?
I bet you did a full wipe in recovery? after that you have to make a full boot into android one time. After that odin will flash if it is the same or a newer version firmware. I have had this problem myself after TWRP full wipe. cant remember if i had to flash a costum rom first? try that if it cant boot. And try to remove phone battery for 30 sec.
Accidentally posted this in the TMO S5 board, my bad.
I've followed the super easy instructions on how to use CF Auto Root but still cannot make it all the way through the first part of the root process. It starts running fine and then stops at NAND Write Start. At one point it got past that but failed at again.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-kltespr-kltespr-smg900p.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Earlier it said something about the PIT partition, but I can't seem to find a 32GB pit file for the Sprint S5 - and it's not saying that any more. I am kind of at a loss here, and now my phone won't boot at all. What else can I do?
Thanks!
Could you first please confirm is Kies installed?
Secondly could you try to change the cable and try a different USB port?
Have you booted your phone into the bootloader? Home + volume down when powering on. Take the battery out and leave it for 10 seconds and then try to boot into bootloader mode.
I got an unlocked note 3 that I have been tring to add a recovery to or upgrade to LP. No matter what file I load in to either 3.07 or 3.09, I keep getting an auth fail. Am I missing something stupid here or is there something I forgot to do when I set odin up?
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.08.9-hltevzw.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Download firmware again .
I have tried that. I have also tried 4 different ver's of odin. I have downloaded the file like 5 times at this point and every time its the same thing. My phone will also display secure check fail :aboot
My device is already rooted from Kingoroot which worked easily and had no problems.
Now I'm trying to install custom recovery, I downloaded the newest IMG that TWRP has for my device, convert it to tar.md5, then I boot my phone into download mode and try to push the rom to my phone via Odin, and after about 3-4 seconds it says fail at the top, here is the output the Odin gives:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> twrp-2.8.4.0-jfltecri.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> twrp-2.8.4.0-jfltecri.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
It doesn't cause any errors or anything on my phone when it fails, I just restart my phone and it works just fine.
Thanks for the help, I couldn't find a similar error to mine with a solution posted previously for my device.
Try using different USB cables and USB ports.
OP resolved the issue. Thread closed.
Need help i get soft bricked my samsung a5 2017 (LDU)
i brought LDU & installed A520FXXU2BQIH_A520FOJV2BQJ1_PAK from sammobile after installation phone sticked into GOOGLE FRP after 2-3 hours searching on youtube i found a method for google frp reset by COMBINATION file so i installed this file COMBINATION_FAC_FA60_A520FXXU3ARA3 in that 7.0 firmware A520FXXU2BQIH_A520FOJV2BQJ1_PAK now device get bricked also then i try more options too then i download
A520FXXU4BRA8_A520FOXA3BQL2_XEF & COMBINATION_FAC_FA60_A520FXXU4ARA4 still fail at wright system in odin also get back to 1st installed 7.0 firmware now get red error on device screen SW REV. CHECK FAIL. DEVICE: 4 BINARY:3
kindly help
Is your problem fixed or not.... If not the problem is with you binary.. You have to have one.. Your best and easiest way to solve your problem is to start all over again and flash your stock rom back and then root your phone.
Don't forget to backup your phone
thank you a lots for reply bro i did same what you said about me but all fail again take a look im not geek to understand kindly give me step by step solution.
with combination file in AP
COMBINATION_FAC_FA60_A520FXXU3ARA3_FAC3ARA3_CL12800524_QB16363926_REV00_user_mid_noship
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 1509 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> param.bin
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
AND WITH FULL FIRMWARE
AP_A520FXXU3BQLA_CL12637612_QB16162045_REV00_user_low_ship_meta
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 4624 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> param.bin
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
ALL FAIL DEVICE TILL THE SAME KINDLY HELP
Single file
download and load single file firmwares of the country
ozkanasilioglu said:
download and load single file firmwares of the country
Click to expand...
Click to collapse
single file not available on sammobile.com
now what to do sir
How do u find the firmware and can I use any version as long as its the country firmware