N900V ODIN AUTH Fail. - Galaxy Note 3 Q&A, Help & Troubleshooting

I got an unlocked note 3 that I have been tring to add a recovery to or upgrade to LP. No matter what file I load in to either 3.07 or 3.09, I keep getting an auth fail. Am I missing something stupid here or is there something I forgot to do when I set odin up?
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.08.9-hltevzw.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

Download firmware again .

I have tried that. I have also tried 4 different ver's of odin. I have downloaded the file like 5 times at this point and every time its the same thing. My phone will also display secure check fail :aboot

Related

Help! I've bricked my phone!

I bricked my phone while trying to flash jasminerom.
I can't seem to get it back to stock with Odin. I'm using the correct pit file and stock but I always end up with this:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N900VVRUCNC4_N900VVZWCNC4_N900VVRUCNC4_HOME.tar.m d5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any ideas? Please help!
I have the SM-N900V with android 4.4.2
Does your phone boot? If so, turn it back on, enable USB debugging and try again.
Does USB Debugging help us to flash the firmware too ?...
Regards
No it does not aid flashing .
OP should download another firmware and try again .

galaxy s6 bricked. how to fix?

<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925IDVU2DOI2_G925IXSA2DOI2_G925IDVU2DOI2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I keep getting this error message when i use odin to flash any firmware and the phone wont boot up. What should i do?
What version of Odin are you using?
It happened to me too one time, i have to go kies and download firmware and install
Kies or Kies 3 doesnt work with S6 Edge Plus. You need Smart Switch. You also need to know your IMEI to use it
Hope you got your mobile fixed

Can't flash stock ROM on GALAXY S5 (SM-G900P)

After a failed root attempt my s5 is stuck on the first start up screen, the one that says powered by android at the bottom. When I try to flash the stock ROM using Odin I get an error message on my phone saying:
SW REV CHECK FAIL : [aboot]Fused 3 > Binary 1
This is my Odin log (I am using odin v3.09):
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900PVPU1ANCB_G900PSPT1ANCB_G900PVPU1ANCB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any help would be appreciated.
Please help!
SecretAgentJeb said:
After a failed root attempt my s5 is stuck on the first start up screen, the one that says powered by android at the bottom. When I try to flash the stock ROM using Odin I get an error message on my phone saying:
SW REV CHECK FAIL : [aboot]Fused 3 > Binary 1
This is my Odin log (I am using odin v3.09):
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900PVPU1ANCB_G900PSPT1ANCB_G900PVPU1ANCB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any help would be appreciated.
Click to expand...
Click to collapse
SecretAgentJeb said:
Please help!
Click to expand...
Click to collapse
Greetings,
Thank you for using XDA Assist. First, please do not bump a thread until at least 24 hours have passed. XDA Assist is a very busy forum and your questions will be addressed when someone is available to answer. I will, however, move this thread to your device's Q&A forum. Good luck!
I want to know this as well. I excluded the problem of different PC and different USB cable. Why is it so hard to flash back stock ROM?
I think you are trying to flash an old version, or one not meant for the sprint phone. The file you are flashing ends in NCB, the latest is OK4.

Cricket sgh-i337z custom recovery error

My device is already rooted from Kingoroot which worked easily and had no problems.
Now I'm trying to install custom recovery, I downloaded the newest IMG that TWRP has for my device, convert it to tar.md5, then I boot my phone into download mode and try to push the rom to my phone via Odin, and after about 3-4 seconds it says fail at the top, here is the output the Odin gives:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> twrp-2.8.4.0-jfltecri.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> twrp-2.8.4.0-jfltecri.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
It doesn't cause any errors or anything on my phone when it fails, I just restart my phone and it works just fine.
Thanks for the help, I couldn't find a similar error to mine with a solution posted previously for my device.
Try using different USB cables and USB ports.
OP resolved the issue. Thread closed.

[NEED HELP] Soft bricked Galaxy A5 2017

Need help i get soft bricked my samsung a5 2017 (LDU)
i brought LDU & installed A520FXXU2BQIH_A520FOJV2BQJ1_PAK from sammobile after installation phone sticked into GOOGLE FRP after 2-3 hours searching on youtube i found a method for google frp reset by COMBINATION file so i installed this file COMBINATION_FAC_FA60_A520FXXU3ARA3 in that 7.0 firmware A520FXXU2BQIH_A520FOJV2BQJ1_PAK now device get bricked also then i try more options too then i download
A520FXXU4BRA8_A520FOXA3BQL2_XEF & COMBINATION_FAC_FA60_A520FXXU4ARA4 still fail at wright system in odin also get back to 1st installed 7.0 firmware now get red error on device screen SW REV. CHECK FAIL. DEVICE: 4 BINARY:3
kindly help
Is your problem fixed or not.... If not the problem is with you binary.. You have to have one.. Your best and easiest way to solve your problem is to start all over again and flash your stock rom back and then root your phone.
Don't forget to backup your phone
thank you a lots for reply bro i did same what you said about me but all fail again take a look im not geek to understand kindly give me step by step solution.
with combination file in AP
COMBINATION_FAC_FA60_A520FXXU3ARA3_FAC3ARA3_CL12800524_QB16363926_REV00_user_mid_noship
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 1509 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> param.bin
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
AND WITH FULL FIRMWARE
AP_A520FXXU3BQLA_CL12637612_QB16162045_REV00_user_low_ship_meta
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 4624 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> param.bin
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
ALL FAIL DEVICE TILL THE SAME KINDLY HELP
Single file
download and load single file firmwares of the country
ozkanasilioglu said:
download and load single file firmwares of the country
Click to expand...
Click to collapse
single file not available on sammobile.com
now what to do sir
How do u find the firmware and can I use any version as long as its the country firmware

Categories

Resources