When I want to put the PDA file in Odin3 to restore the phone because it does not start I get this error message on the phone "firmware upgrade and tell them issue. Please select recovery mode in kies and try again" I can not use Kies for it is that I entering the wrong model and when I put the PDA file in Odin3 then I FAIL! continuously
HTML:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUFNC5_I9505HTSFNB1_I9505XXUFNC5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
I bet you did a full wipe in recovery?
I bet you did a full wipe in recovery? after that you have to make a full boot into android one time. After that odin will flash if it is the same or a newer version firmware. I have had this problem myself after TWRP full wipe. cant remember if i had to flash a costum rom first? try that if it cant boot. And try to remove phone battery for 30 sec.
Related
Hey everyone,
I believe I just softbricked my phone, I tried to restore it back to stock via ODIN but it wont work,
Here is the error message from ODIN
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337MVLUAMDJ_I337MOYAAMDJ_I337MVLUAMDJ_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> recovery.img
<ID:0/003> persdata.img.ext4
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And it stuck on the screen that shows "firmware upgrade encountered an issue please select recovery mode in kies and try again"
WHAT DO I DO? :crying::crying::crying::crying::crying::crying:
Try flashing this http://forum.xda-developers.com/showthread.php?p=46943588 via Odin forI337MF3......cuz the one u used is for I337MDL ....
Swyped from BlueICESense_JBE
take a look at Jamison's guide just to see if you did some steps wrong
it is mdl so don't use the fw but the steps may be similar
http://www.infamousdevelopment.com/index.php?topic=115.msg890#msg890)*
I got an unlocked note 3 that I have been tring to add a recovery to or upgrade to LP. No matter what file I load in to either 3.07 or 3.09, I keep getting an auth fail. Am I missing something stupid here or is there something I forgot to do when I set odin up?
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.08.9-hltevzw.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Download firmware again .
I have tried that. I have also tried 4 different ver's of odin. I have downloaded the file like 5 times at this point and every time its the same thing. My phone will also display secure check fail :aboot
I bricked my phone while trying to flash jasminerom.
I can't seem to get it back to stock with Odin. I'm using the correct pit file and stock but I always end up with this:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N900VVRUCNC4_N900VVZWCNC4_N900VVRUCNC4_HOME.tar.m d5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any ideas? Please help!
I have the SM-N900V with android 4.4.2
Does your phone boot? If so, turn it back on, enable USB debugging and try again.
Does USB Debugging help us to flash the firmware too ?...
Regards
No it does not aid flashing .
OP should download another firmware and try again .
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925IDVU2DOI2_G925IXSA2DOI2_G925IDVU2DOI2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I keep getting this error message when i use odin to flash any firmware and the phone wont boot up. What should i do?
What version of Odin are you using?
It happened to me too one time, i have to go kies and download firmware and install
Kies or Kies 3 doesnt work with S6 Edge Plus. You need Smart Switch. You also need to know your IMEI to use it
Hope you got your mobile fixed
My device is already rooted from Kingoroot which worked easily and had no problems.
Now I'm trying to install custom recovery, I downloaded the newest IMG that TWRP has for my device, convert it to tar.md5, then I boot my phone into download mode and try to push the rom to my phone via Odin, and after about 3-4 seconds it says fail at the top, here is the output the Odin gives:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> twrp-2.8.4.0-jfltecri.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> twrp-2.8.4.0-jfltecri.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
It doesn't cause any errors or anything on my phone when it fails, I just restart my phone and it works just fine.
Thanks for the help, I couldn't find a similar error to mine with a solution posted previously for my device.
Try using different USB cables and USB ports.
OP resolved the issue. Thread closed.