Related
(Not sure if there has been a post about this, apologies if there has.)
Just wanted to let everyone know that I had a fairly big scratched area, right where I write the letters for the Letter Recogniser SIP which was very annoying as it prevented the stylus from gliding smoothly. I heard that I should use Brasso (~£1.30 from your local supermarket) on the screen and it has been VERY successful. It's completely removed the scratch.
Just apply a small amount with a cotton-bud and work into the screen in circlular motion (press harder for deeper scratches). Keep doing this for about 10-15 times or until the scratch disappears.
Hope this helps anyone with screen scratches or anyone wondering about using Brasso but too scared to try.
Careful
I wouldn't recommend it as too much brasso will affect the screen, It's not just an abbrasive but solvent too so you will melt the plastic screen. Over-use will make the screen look warped.
I tried this on my M500 ages ago; now if HTC have improved on the screen then hey.. go ahead but don't say I didn't warn you.
Screen protectors are a much better option. If the screen is already marked a protector would give you a smooth finish again. If thats to expensive an option clear contact sheet will also offer the same results and a roll of that will give you screen covers for the rest of your natural life.
it would not "melt" the screen - how misguided. it is a mild solvent and abrasive and so is unlikely to cause much harm to the screen unless used constantly. screen protectors look awful on a screen - especially when the device is off.
http://www.mobilecomputermag.co.uk/2007100487/my-laptop-screen-is-scratched.html
Off topic a bit. I bought an expensive screen protector from Brando.. it works very well.. but.. for some reason it (the screen protector) got scratched. any easy way to solve it? Brasso is ok? I thought if there can be any method of using .. say car wax to fill in the grooves of the scratch.
I think it got scratched when stuff like sand got attached to my face and when I list to the phone, it stick onto the scren pctr.. and when I write on it.. it got scratched.
Just be happy you had the screen protector on!
I tried to take out the scratches from the plastic cover on my Casio watch with (Crest) toothpaste and it worked FANTASTIC!!!
Thanks a lot to the Guy who suggested this solution for PDA screens.
Damage to screen with brasso
rich1986 said:
it would not "melt" the screen - how misguided. it is a mild solvent and abrasive and so is unlikely to cause much harm to the screen unless used constantly. screen protectors look awful on a screen - especially when the device is off.
Click to expand...
Click to collapse
OK it doesn't melt the screen off but it gives it a warped look if you reflect light off it.
No tricks can help
Do not fool yourself. Brasso, toothpaste, Displex all leave marks on the screen. Check it with the device off in sunlight or a strong light source.
Brando protector is expensive.
Cheap and perfect is a new digitizer (USD 8).
I just ordered two more. And whenever I get a scratch and I have time I replace it.
hmmm... Brando's protector is selling for 9-10 dollars - you can easily find cheaper alternatives.
I guess the time and hassles (and of course the warranty alone) of replacing the actual digitizer don't really worth the few bucks saved.
Having recently bought my son a Nintendo DS, I noted that in the accessory pack I got with it, it came with 2 screen protectors that are semi-rigid. They're quite a bit thicker than one that shipped with my phone, and don't flex and bend like thin paper. They also don't seem to affect sensitivity of the touch screen in any way, as well as being perfectly sized to the screens and were invisible once fitted.
Are there similar protectors for the TyTn 2? I'd love such a protector as it'd be FAR easier to fit, and provide much better protection to the screen.
Rigid Screen Protectors
I have come across these. The ones I tried were made by "Martin Fields" product number MFOP-HTCTyTN-T
A right bloody bastard to fit as they are very slighty oversized. Perhaps this is done purposly so the protector fits into the gap around the edges of the screen?
Very clear and reasonably priced compared to the OEM product. They do work extremely well (once fitted).
Rgs,
J
Thanks. I'll check em out.
invisibleSHIELD.. That's all I have to say.
oH, view the demo also.. its well worth it.
I just checked my little brother's DS box, hoping to find the screen protector but nothing there but manuals =(
Any reference on how firm and rigid the MField or InvS are?
Well, from the video, the invisibleShield isn't the slightest bit rigid, though if it lives up to its claims, that wouldn't matter. I ordered a Martin Fields one earlier so I'll see how good that is.
It's not just the rigidity for protection though. A rigid protector will be a LOT easier to fit...
Beleave me, MF is rigid. And yes, it is easy to install but remember to clean the surface of the screen. This part is very important. If you do it right, it will install in less than 30 seconds and you will struggle to see the difference between no protector and MF.
Oh I know that. I'll be cleaning it very carefully and making sure there's no dust about when I fit it! Don't want dust under the thing!
Just wish it'd hurry up and arrive!
boxwave
The boxwave protectors are much thicker than average ones, are washable, and work great. They are about as thick as the psp protectors, e.g. more like a hard plastic sheet, I'm not sure what the ds ones are like.
http://www.boxwave.com/products/cle...crystal-screen-protector-htc-tytn-ii_2905.htm
tke371 said:
invisibleSHIELD.. That's all I have to say.
oH, view the demo also.. its well worth it.
Click to expand...
Click to collapse
FYI, a warning this could break your Tilt!!!!
This shield rocks. However it's a risk for the Tilt. You have to apply water to the back of the protector to get the bubbles out. I applied water, shook the excess water off before applying.... and stuck it on.
I used the included squeegee to get the excess water out of the shield along with the bubles. I wiped extra water away. Next day, my screen was dead (colors were washed out and glitches). Apparently during the squeegee process water slipped between the screen surface and the edge of the bezel around the screen, and in to the phone, and got under the LCD plastic into the LCD itself.
I do use this product on my $2700 SLR camera. There's no bezel on the LCD so the squeegee'd water comes right off, and won't get in the camera.
Beware. I had to get a new Tilt because of this, and it'll be a cold day in hell I use this product on any item with a bezel where water can seep in.
Semi- related: how are you guys cleaning your phone screens?
Oh, and +1 for Martin Fields.
My phone broke, but I had insurance on it (not from phone company but through homeowner's via a personal property rider), and mycellularrepair.com was able to replace the LCD for $200. Also, never buy that phone company insurance. Personal property rider is the way to go. It was just pennies a year for ~$500 of coverage for the phone. NO DEDUCTIBLE! So I paid nothing to have my phone fixed.
Get a NEW ONE - They're Cheap
jon_k said:
FYI, a warning this could break your Tilt!!!!
This shield rocks. However it's a risk for the Tilt. You have to apply water to the back of the protector to get the bubbles out. I applied water, shook the excess water off before applying.... and stuck it on.
I used the included squeegee to get the excess water out of the shield along with the bubles. I wiped extra water away. Next day, my screen was dead (colors were washed out and glitches). Apparently during the squeegee process water slipped between the screen surface and the edge of the bezel around the screen, and in to the phone, and got under the LCD plastic into the LCD itself.
I do use this product on my $2700 SLR camera. There's no bezel on the LCD so the squeegee'd water comes right off, and won't get in the camera.
Beware. I had to get a new Tilt because of this, and it'll be a cold day in hell I use this product on any item with a bezel where water can seep in.
Click to expand...
Click to collapse
Interesting - Are you really that concerned about a product which is relatively cheap compared to the amount of time use you get out of it? Forget washing it off. Just put another one on - a CLEAN NEW one. If they last a long time (like in most cases a year or more), who cares that you have to spend around $20 to get a replacement. If they stopped making them altogether or they cost a ridiculous amount of money (for plastic, ridiculous. For peace of mind, priceless), then yeah, I would wash and rewash the screen to save money.
And the idea is NOT to squeegee the WATER bubbles out to the sides. They will evaporate on their own given some time. The idea IS to squeegee the AIR bubbles out to the sides and also to take extra great care when doing this procedure. You wash it off so that it restores some of the tackiness on the film. You can get most of the water off by blowing or using a can of compressed air, THEN put it on. You shouldn't have that much water under your film if you take care when doing it.
I am sorry about your tilt. That really sucks. If I were you, I would just put a BRAND NEW one on next time and forget about washing it off.
~Gwen
I need one of these too, recently the digitizer for the touch screen on my phone cracked. They are charging me 50$ for the screen and 40$ for labor. My question would be, would this rigid screen have prevented my digitizer from breaking? If it would then id buy it in a second.
I'm giving a +1 to the Martin Fields as well.
I just got a couple of them for my phone. They're definitely more rigid than some of the others, but I put it on a clean screen & can barely tell I have one on.
Stylus slides smoothly across it, no visible scratching at all (unlike the OEM one that marked easily), & it's also pretty smooth for finger usage too.
Had to wait a week for them to ship via expansys-usa, but worth the wait.
any one with recommendation on screen protector
I'm currently using a Zagg max coverage protector that I had installed at Best Buy, and have no complaints so far. The only thing I've noticed with it is that my finger tends to get stuck when using Swype, but not often enough for it to bother me.
I don't have this phone but I don't think you need a screen protector. I haven't seen any videos on the screen durability test like they do for the iphone scratch test. But I think the screen should be sturdy enough. The screen won't be as smooth to scroll with a plastic layer. And if you accidentally get even a drop of water in the corners of the phone with the squeegee, you are screwed. Good luck.
Using an Invisible Shield on mine. This is the only phone I've ever used one on. I figured with a screen this huge I want to keep it looking nice.
You don't need you it is glass like the Iphone and hero. I have seen test's on both using key to try and scratch nothing happened. Anything that would damage the screen (scratch it) would go right through the screen protector and still damage it. As it would take a lot of force to scratch. Just a wast of money not to mention it hampers the touch screens ability to pick up your finger.
someone apparently water damaged their evo with putting on a protector. Careful. I would cover up the indicator on mine once I get it.
i have a zagg on mine and hate it. its sticky and has a "orange peel" like appearence. i ordered a hard plastic one on amazon and am waiting for it to come in the mail.
I also feel that a screen protector is unecessary...glass is very hard to scratch, and can only be scratched by something harder than it is.
Zaag one here and I think it's too sticky. It messes with my swiping. Catches my finger too much.
chazglenn3 said:
I also feel that a screen protector is unecessary...glass is very hard to scratch, and can only be scratched by something harder than it is.
Click to expand...
Click to collapse
I used the same logic with my hero and ended up getting a few scratches just from unforseen sh!t happening. this screen is too beautiful for me to risk.
also whoever water damaged their phone while putting on a screen protector is an idiot.
I put one on for peace of mind and it works just as it did without the protector.
However, if it's like the iPhone screen, then you shouldn't need one at all. I had the same iPhone since the release date and had zero scratches as of Friday... it's last day in service!
We pre-ordered out Evo's at RS so we used out accessory credits for Zaggs and car chargers and I put them on. They do have an orange peel like look when looking at them at a angle with the screen off and reflecting off some light. But with the screen on and looking at them there is no issue with the display. They were not hard to put on either.
I'm using the "anti-glare" protector that comes in the 3-pack you get at the Sprint store for $12 (the other two are "clear"). I love it - it doesn't interfere with my user experience at all. Why on earth would you risk scratching your screen? To save $4 and 5 mins time?
Boxwave Crystal Clear screen protectors. I have a 3-pack on order (I have 2 Evo's between me and my girlfriend). We're using them "naked" so far until they arrive.
I highly recomend the Boxwave protector though, I have used them for about 6+ years on various PDA/Smartphones. I even have one for my P&S Camera.
Here is my experience:
Zagg:
Good -
Works well as protection
Hides fringer prints decently
Bad -
Blurs your screen a very small amount
Makes the surface feel like rubber
Hard to put on without getting a little dust under it
Generic hard plastic sheet:
Good -
Works well as protection
Feels very smooth, smoother than glass
Easy to put on, and normally you get 2 or 3 in case you make a mistake
Perfectly clear
Bad -
Finger print magnet, oil really builds up
You can see where the protector ends around the edges
Added glare in sunlight(small amount)
Unprotected Glass:
Good -
Feels very smooth
Easy to clean off, just rub it off on your shirt
Perfectly clear
Bad -
Medium finger print problem, but easy to clean
I feel scared to place it face down, once I get a case that recesses the face I will feel better.
Over all I decided to go with unprotected. Its the middle of the road and I feel the best over all experience.
Zagg Invisible Shield is NO GOOD.. Its almost sticky. Don't get it! I warned ya.
zone23 said:
Zagg Invisible Shield is NO GOOD.. Its almost sticky. Don't get it! I warned ya.
Click to expand...
Click to collapse
Agreed, the Zagg is sticky. But I deal with it so that I can protect it. I don't have a huge issue with viewing it or the orange peel look when it's off because you don't notice it when it's on. The fit is nice. On my hero, I had a really clear smooth one from ebay which was great, but was all scratched up. The zagg shouldn't even mark up which is why i'm dealing with it. Sticky, but not to the point that it pisses me off. I put it on myself relatively easily, just spray lots of that solution on it, no bubbles, no dust, 2 minute application.
Maybe the Zagg is sticky if you put it on backwards but I have ZERO complaints about mine.
I ordered a 3 pack of anti-glare/anti-fingerprint screen covers from handhelditems for 7.99 (for the 3pack). They have crazy deals on evo 4g accessories right now. I also got a car charger for like 3.99.
I bought it more for the anti-glare/anti-fingerprints than the actual screen protection.
Warning!
There is a whole thread started on water damage and most of this comes from any screen protector that requires you to spray on water... ei Zaggs
When you squeegiie the water off the screen it leaks in to the back of the phone and Sprint has been sneaky about placing water damage indicator right on the tip of the phone.. below battery.
Either cover the indicator with protector or stick to the regular screen covers..
Hi!
I got my hands on ZAGG's invisibleSHIELD for X10, it's on the way thru delivery.
I saw their videos, and it's seem hype.
Anyone have personal experience with this product?
Also, right now, I have a rubber-not-so-tight-fit casing for the X10, but I want to get one that has tight-fit, real tight fit rubber casing to put on after the invisible shield? Recommendations?
Something in the lines that matches with iSkin, that the have for the "not so hype" iPhone...
If you go up a level to the Sony Xperia X10 menu page and have a look in the accessories subsection there is a lot of info on cases and screen protectors etc which might be helpful to you.
I bought Zagg's full body invisible shield before for my SE Satio. They were difficult to apply. Also, the screen responsivenss was better on the stock screen protector. You dont really need to replace it if yours came with one. The Zagg screen protector feels sticky to the touch. Not so good on a capacitive screen
Zagg's invisibleshield is horrible. My buddy got one for his x10, and I applied it. Every piece was not cut precise except the back cover. The front screen protector wasn't even cut straight. The left and right borders were tapered in the middle leaving about 2mm of space, on each side, between the border and the screen protector.
From my own experience with the product on my x1, the full body shield turns yellow and traps tons of dirt at the edges. It just looks cheap over time.
Backcover? People actually _like_ having slippery backs? Imo the stock coating is optimal since it's very grippable, it's rugged and it doesn't gather any fingerprints.
ddewbofh said:
Backcover? People actually _like_ having slippery backs? Imo the stock coating is optimal since it's very grippable, it's rugged and it doesn't gather any fingerprints.
Click to expand...
Click to collapse
Well, I was just stating a fact that it does come with a back shield, and it's the best cut piece of the set. While I do like the bare back feel of the x10, the option is there for people to use it or not use it.
I got myself a Martin Fields screen protector. Applied it today. So far really loving it. Will review it soon.
InvisibleSHIELD is also supposed to be real good, but a pain to apply correctly.
needmoregigs said:
Zagg's invisibleshield is horrible. My buddy got one for his x10, and I applied it. Every piece was not cut precise except the back cover. The front screen protector wasn't even cut straight. The left and right borders were tapered in the middle leaving about 2mm of space, on each side, between the border and the screen protector.
From my own experience with the product on my x1, the full body shield turns yellow and traps tons of dirt at the edges. It just looks cheap over time.
Click to expand...
Click to collapse
I had the same experience with my Zagg sheild. Tappered sides and what not. Anyway I am not a fan. What I would like to know is if there is similiar screen shields to the ones for the iphone?? They have almost the texture of a sheet of paper, never streak and seem to provide excellent responsiveness. Im not sure of the different types of protectors but if someone knows of one like this let me know!
Also the Zagg shield on the back of the X10 is actually pretty sweet......its not slippery. In fact its the exact opposite. You can set the thing down on the dash of the car while charging and it will not slide around at all. But hey, if thats worth $20 then have at it.
Not bad...
I have the invisibleSHIELD for my X10 and it's not to shab... but not too good...
As with one of the posts above, the front screen protector was not cut to fit properly; there is a gap on my screen about 1/4" on the right side, however the left side is flush. I emailed Zagg about it and they have sent me a new one and apologized that the case was damaged during shipping (although it was very clearly NOT damaged during shipping, it was just cut that way).
The rest of the case fits snug, but it does get dirty/sticky on the edges. I will be getting another case to put over it; likely the FlexiShield.
I personally like the feel of the screen protector more than the stock protector. I have both of them on right now and have no issues with the touchscreen whatsoever. The Zagg shield never fingerprints, but it would with the stock protector.
Overall, I would give the invisibleSHIELD a 7 out of 10. If I was rating the screen protector alone I would give it 8 out of 10 (points dinged for the improper fit, hopefully the replacement sits flush).
If you are like me and want a mint looking phone you might get a little frustrated by the scummy edges, however the material is strong and you will definitely not scratch anything. I recommend doing away with the full body case and just getting the screen cover in combination with another case!
Cheers!
Update: Received the replacement but the screen protector is even more tapered on the edges than my original. I've scrapped the shield and went with a plastic fitted case. Too bad, I really like the quality of the material. I'm going to try and get a refund.
Wow! Judging by the reviews, I am not glad that I went for MF instead of ZAGG.
I got protech which is essentially the same thing and I have to say its pretty good. I've used invisible sheiks in the past on a g1 and found it was easier to apply to the x10. You have to be really patient though if you leave the smallest air bubble on the edge as previously mentioned dirt and dust gets trapped underneath and starts to peel.
Sent from my X10a using XDA App
I have full body Zagg ... it sux.
The size of the front part is not right so i have about 2mm on edges which are not covered.
The top, bottom and side parts are already gone.
The back part is still there ... for now.
I have a gadget shieldz full body.
I'll try it in about 2 weeks when the zagg will be gone.
Zagg lasted about 3 months.
I have the Martin Fields one bought from Mobile Fun. It is the biggest fingerprint magnet in the history of phones. I bought the double pack thinking I'd have a spare as back up. The actual screen applies beautifully but it has lifted in the top right hand corner near the proximity sensor. I managed to reapply it without taking it off totally but its still not perfect.
I want the same shield we bought for hubby's Iphone. Its a matt anti reflective one and shows no finger marks. I spend my life cleaning smudgy prints off mine.
To clear out what others said and my experience with zagg shield,
It all comes to how accurate are you when attaching it.
But if you want some advice, just put the back part only. The stock screen protector is much better, the side parts are too hard to put on.
and take care They are very stretchable. ..
Sent from my X10i using XDA App
I agree, the Zagg screen protector makes the screen slightly sticky or something. Makes it hard to drag things across the screen like when moving cards in Solitaire etc. I'm on the lookout for a good screen protector now, wish i never removed the stock one!
I actually like the feel and look of the back protector and yes, the side and bottom protectors are a bit too finicky and strechy for clumsy people like me to put on properly!
Painfull Installation - Happy Though!
Hey!
So, I finally had time over the weekend to apply the invisibleShield to my X10, the full-body, "maximum protection" version.
Just let me tell you:
(1) Painfull process - took nearly 2 hours from start to finish, minus break / re-doing time because i wasn't completely satisfied.
(2) Not enough solution - the spray bottle they gave is enough for 1 time installation only! No room for mistakes. Found out the solution was Johnson's brand baby shampoo & distilled water (I didn't have any distilled water, instead, used a new bottle water from Nestle brand) ... worked like a charm
(3) sizing - oh man! the sizing of the invisible shield is not perfect, except for the back piece ... front has gaps, 1/2mm or less on either side.
(4) Applying ... it took me about 3 times to get it right, fitted accordingly. That's how I ran out of the solutions.
(5) Squeeze is not good on small pieces, better to use a q-tip to slide thru the solutions off.
Overrall, it's a different feeling. Getting used to it.
Only thing I would ask ZAGG to do is: PROVIDE A BOTTLE WATER size of solution!!!! & correct sizing of the pieces.
- Just 1 or 2 mini bubbles seen just by me, otherwise, it's a charm!
Still, I got my hands on a iPhone 4 32GB as well, kit for that is coming soon. Should be easier ...
I wish they had Otter Box style casing for X10.
tell us about fingerprint and screen clarity ...
naveen_reloaded said:
tell us about fingerprint and screen clarity ...
Click to expand...
Click to collapse
Clarity is ok.
Fingerprints ... way better than the original but still not good enough ...
Just don't drop sun protection lotion on your phone
You will need another invisible shield ...
Fingerprint is not there, or atleast, very much of it is reduced. I am a clean freak, so, I clean it everyday before putting it to charge for the night.
Senstivity was something to get used to, little bit off in the beginning, but after the curing process of the invisibleshield, it works like a charm.
Anyways, I contacted ZAGG, they are sending me another full kit for the X10, since I complained about the sizing & not enough solutions ...
I have to wait for approx 1.5 weeks to receive, remove the old/existing one, and do it correct the 2nd time around.
Of course, i need to send back the one I have right now when I receive the other one...
I'll post a message on how my 2nd attempt went, (with extra bottle of solution, yeah! that's right! I demanded to the agent on the email for 2nd bottle of solution)...either way, baby shampoo & distilled water is good enough too.
Screen Clarity - 100% or 99.99% , unless you angle the phone differently in the light or reflection , you dont see it.
I had the full body but took it off.
I bought the white X10 in dubai, like everyone else said fitted poorly and bleeds the colours from your case, I had to take it off as everyone was saying how battered the phone looked after a month.
It is pretty bullet-proof though, sure it must look better on the black phone!
Hello all, I have a question about the gorilla glass on the DX. In your opinions, do we need a screen protector or not? I'd love to just have the glass front but also don't want to harm the phone. Also, exactly how many gorillas were sacrificed to make each glass screen? I want to rub it in PETA's face.
EsotericPunk said:
Hello all, I have a question about the gorilla glass on the DX. In your opinions, do we need a screen protector or not? I'd love to just have the glass front but also don't want to harm the phone. Also, exactly how many gorillas were sacrificed to make each glass screen? I want to rub it in PETA's face.
Click to expand...
Click to collapse
To use a screen protector...or not to use a screen protector.. that IS the question...
Um.. I think its more of a personal preference... Do you tend to be harsh on phones? Or do you take care of them.... That is probably some of the thinking you should put into the matter.
I have had my X for around 7 months, and I take it all over. I have not scratched my screen at all... Its really if you are overly worried about it getting scratched... If so, why not spend a few bucks to protect your precious investment!
I NEVER rocked screen protectors until I got my X... and that wasn't until I saw a scratch on a friends.....
My advice would be if you are going to get one, get a good one like steinhell or however you spell it.
If you get their top of the line it s also good at fighting against fingerprints.
+1 for sysadmin
and elevendy6 gorillas were sacrificed
If you are going to keep the phone in a jeans pocket I would say get the protector.
The SGP crystal clear you can't even tell it is there.
How easy is it to get a piece of sand in your pocket and it is harder than the glass.
http://chemistry.about.com/od/geochemistry/a/mohsscale.htm
get anti-glare ones, they show less fingerprints
Never used a screen protector or case. Never even bothered to take care of my phone. No marks on it whatsoever and I got it on launch day. Get a screen protector if you want to crappy looking layer of scratched up plastic over your screen. Get a case if you want your phone to be all scratched up.
Cases and screen protectors both do more harm than good.
My Droid X has proven very sturdy. It's been dropped, kept in random pockets exclusively (with keys occasionally) and has no scratches on the glass. The only damage to the body is a couple of minor dents in either upper corner, which have to be pointed out, and scratches on the back "M" logo.
I typically use a two-piece plastic shell, because I like the way it looks and it offers a little protection when dropped. I tried the Zagg Invisi-shield, as well.
I can't recommend the Invisi-shield, though. It went on with a little work and it felt fine to the touch. It was also only slightly more smudge prone than the glass itself. However, I scratched the protector the day after installation with a paper napkin. A couple weeks later, and a few bucks for shipping, my replacement shield was delivered with a tiny scratch in the center of the front side.
I say run without protection.
I have had my X since it came out. I briefly had the crappy Verizon screen protector/antiglare film on. I keep my phone in my pocket with the glass against my leg and have had no problems. For Christmas I got the Seidio surface combo case. So it isn't in my pocket as much anymore.
Ive had my X since before froyo with no protection whatsoever. I carry it like jgraham with the glass against my leg. I've dropped this thing on blacktop and facedown on concrete. Not a scratch on the screen. I have some nasty battle scars on the little ridge that protrudes up past the screen though.
I can't stand the screen protectors. I don't like the look or feel of them. If you destroy the glass somehow, just pay the $50 deductable or whatever. Well worth it to me.
Sent from my DROIDX using XDA App
I also recommend the Seidio Crystal Clear protector. It's much more invisible, and less friction, than the Zagg InvisibleShield. It's also much cheaper (you get a 2-pack for almost 1/2 the price of one InvisibleShield).
I've been using the Seidio for a few months now and it works great. I can't even tell it's on my phone, except it collects smudges a bit more than the naked glass. But a quick wipe on my shirt removes them. Cheap insurance in my book.