Sorry but i'm just a newbie here. Plz help me ... I'm having someproblem with my SS4 I9500 GSM only model. Just bought it a few days ago and yesterday after I root it with Kingroot everything still ok until I download the TWRP recovery on CHPlay. It show some kind of warning that could affect my SD but I ignore and have it done something to install the TWRP on my phone. After one time reboot my phone started to run real slow , super hot until hang itself and extremely battery draining ( about 25 - 30 % for one time boot till it hang and reboot ). I've tried to reinstall an Original Firmware but couldn't because I can't connect my phone with the PC everytime I tried to connect the cable my PC show the Code Err 23. Device not recognized. . I tried the factory reset but it still operated like that and there's no TWRP but the original recovery of android. Changed the cable , changed the PC , still nothing happened. Someone plz help !!!
Related
Dear all,
I have only recently lost my IMEI und tried everything to recover it. As a matter of fact I had made a backup before and tried to restore it and it didn't work. Today, I tried doing that another time and after that I wanted to reboot my phone but after it shut down it just doesn't boot up anymore. It shows nothing, only the black screen. It seems like it doesn't react to anything, I also tried to pull the battery but that also wasn't successful. I also can't get into Download Mode.
Any ideas what I could do?
Charge the battery or try another battery first .
I did both, I charged the battery but it didn't help and I also tried another (fully charged) battery, without success.
try to connect with kies 3
Kies doesn't recognize my phone.
Service centre repair your next step .
I'll let my carrier send it to Samsung and tell them that it crashed after trying to update to Lollipop via Kies, I read that this worked in some cases. If it doesn't I'll have to have it repaired.
What do you guys think about those "USB jigs"? Do you think those could help me with my problem?
YAAAAY!
Thanks to this thread http://forum.xda-developers.com/showthread.php?t=2625332 I was able to unbrick my device and by flashing a new PIT-File and a Stock ROM even my IMEI came back. I think my partition was somehow messed up because after flashing the PIT-File it began to work properly, but I flashed the Stock ROM to have a "clean" system again and installed Cyanogenmod afterwards with success.
So how does this fix work if the phone is unable to connect or power on ..
OP yes try the usb recovery jig to see if it boots to download mode .
Well, it did help. After I had put the Image on my SDcard and removed my SIM card I was able to boot my phone, this was the main issue. The rest was child's play, I flashed the PIT-file and a stock ROM and everything was working fine again.
flash new PIT file
hi you got to flash a new pit flie. maybe something damaged your phone boot. look in here
http://forum.xda-developers.com/showthread.php?t=2625332
Hello,
i have a problem with my 1 week old yotaphone and hope you guys can help me to solve.
Let me say, this is my first android device. After a long time using iphones i saw this 2-displays concept and wanted to give it a try.
But now my problem and the way to:
The phone was brand new and first of all i charged it for a wohle night.
After that i put in the sim-card and started the phone and walked through the start-procedure with WLAN, Googleaccount etc.
Then the phone told me about an update and i started it over WLAN.
The phone was downloading, rebooting and shows me a white window "updating x of 127(?) Apps".
Somewhere in the middel the phone rebooted again and now its in a bootloop.
What is possible with the phone right now.
I can start the phone wit the bootloop (powerred byAndroid, then restart)
I can use "Power + Vol-" to bring it into downloading mode
When i use "Power + Vol+" nothing happend.
When i use "Vol+ + Vol-" nothing happend.
The akku of the phone is empty now and it only works with usb or power unit connected.
In bootloop or downloading mode it is not charging.
What i tried.
What i try:
I read many topics with bricked / bootlooped yotphones and how to flash or cache whipping.
i connected the phone to my pc and used yotoflasher with many different firmwares.
I used fastboot:
- flashed the system.ing with differnet sizes.
- tried different custom recovery.img from different threads here and from other sites.
Even a complete new image, moddified RU img doesn`t help.
The phone stays in bootloop.
Yes, it`s a warranty case, but before i start to strech my nerves by handling with the dealer and shipping
this phone back to china i will try everything else and hope you can help me out of this situation.
Thanks a lot
easyxx said:
Hello,
i have a problem with my 1 week old yotaphone and hope you guys can help me to solve.
Let me say, this is my first android device. After a long time using iphones i saw this 2-displays concept and wanted to give it a try.
But now my problem and the way to:
The phone was brand new and first of all i charged it for a wohle night.
After that i put in the sim-card and started the phone and walked through the start-procedure with WLAN, Googleaccount etc.
Then the phone told me about an update and i started it over WLAN.
The phone was downloading, rebooting and shows me a white window "updating x of 127(?) Apps".
Somewhere in the middel the phone rebooted again and now its in a bootloop.
What is possible with the phone right now.
I can start the phone wit the bootloop (powerred byAndroid, then restart)
I can use "Power + Vol-" to bring it into downloading mode
When i use "Power + Vol+" nothing happend.
When i use "Vol+ + Vol-" nothing happend.
The akku of the phone is empty now and it only works with usb or power unit connected.
In bootloop or downloading mode it is not charging.
What i tried.
What i try:
I read many topics with bricked / bootlooped yotphones and how to flash or cache whipping.
i connected the phone to my pc and used yotoflasher with many different firmwares.
I used fastboot:
- flashed the system.ing with differnet sizes.
- tried different custom recovery.img from different threads here and from other sites.
Even a complete new image, moddified RU img doesn`t help.
The phone stays in bootloop.
Yes, it`s a warranty case, but before i start to strech my nerves by handling with the dealer and shipping
this phone back to china i will try everything else and hope you can help me out of this situation.
Thanks a lot
Click to expand...
Click to collapse
Mine too,stuck in bootloop. I also tried the fastboot and it said waiting device.
kophyo07 said:
Mine too,stuck in bootloop. I also tried the fastboot and it said waiting device.
Click to expand...
Click to collapse
If your phone displays Downloading... and fastboot keeps saying waiting for device then there is something wrong with the installed ADB driver. Check some of the posts in this forum like this one on how to fix this. http://forum.xda-developers.com/yotaphone-one/help/yotaphone-2-yd-206-china-flash-firmware-t3306797/post69311402#post69311402
Strange that you had an OTA (Over The Air update). You didn't do anything between the SIM/Google registration and OTA ?
Normally there are no OTAs allowed on yd206 phones bought from China/HK , where did you buy it ? Chinese retailers have their own firmware that they put on phones , for me , maybe you had bad firmware installed.
The warranty of your phone is voided if you flash yotaphones bought from China and HK .
When you use yotaflasher do you get error message or "waiting for device" ?
To flash the Yotaphone , it should be in developer mode , but you couldn't put it in this mode because it first did the OTA that started your bootloop. Android apps are updated like that ("installing x of 127") when it gets updated to lollipop. Normally the OTA should have worked OK. Did you allow enough time at the Yotaphone logo after the first reboot ? It stays on this logo for 5 minutes before starting. I made this mistake.
The OTA started just after you set up Google etc ?
If so, normal yotaflashing will never work, but at least you havent broken the warranty . The thing we need to know is what exactly happened when you tried to flash , what errors messages appeared ?
If you did not put the phone in developer mode, then you cannot easily flash the phone, so your best possibility is to return the phone. Normally you can contact the seller by chat or email . Some are very good in exchanging.
It IS possible to flash your phone using fastboot, but I would not personally attempt it and you would lose your warranty . You need rootkits, SDK toolkits, universal drivers and images. Google "bootloop without USB debugging".
When I flashed my yd206 , (after many attempts) I flashed my yd206 to yd201 Russian KitKat ROM first and then did an OTA to lollipop.
can anyone help me with my problem?!...
earlier today, i tried to upgrade my grand 2 from 4.3 to 4.4.2 via odin.
I downloaded all the required files and started the process, i got my phone into download mode and plugged it in my pc (i used a cheap usb cable) and pressed start.
after 30 seconds it stopped and failed the upgrade.
i tried to flash it again and it was the same.
now my phone won't even boot or charge or enter download mode.
PLEASE HELP!
sorry for the long post.
Its ok brother...it happens...and i dont think so its becuz of cheap usb cable i think its becuz ur ROM was not properly downloaded!
Now as becuz u cant go to download mode...try going to recovery and reset your phone ! if you get successfuldo that...i think you'll be able to boot to download mode #likemypostifyoufeltok
Hello guys!
Unfortunately I have managed to full brick my phone which has worked without any issues for more then 3 years.
My story:
1. Phone started to have random restarts, basicaly, when phone lagged little bit - it restarted phone.
2. When I did manual restart, I got into bootloop and could not get out
3. With a heavy heart I did a factory reset. - Problem with random restarts ontinued together with random bootloops.
4. Did maybe 5 more factory resets, nothing happened.
5. Found a tutorial to flash new firmware.I was on 5.0.2 D802 30d so I used same. (PC suite could not find my phone and LG support tool always freezed on SW install)
6. I used LG Flash tool with normal flash. - used *.kdz which I have downloaded via LG support tool - checked size with dl from source from xda and they were same so i used it.)
7. All success, but device keep restarting - i think no bootloop anymore.
8. I did full flash again with LG flash tool so have a clean install and hopefully fix everything.
9. Suddenly mid-install my phone auto-disconnected from laptop and even with Retry attemps I wasnt able to get it running again. Then my phone restarted itself and that was it.
Now I cannot go to recovery mode, I cannot go to Download mode, all I see is black screen (turns some light on little bit underneath but no data visible).
Also when connect to my Windows 10 laptop multiple discs trying to load and trying to format disk. (one of them contains folder image with some files inside).
I dont have root, I dont have any other tools installed on my phone, just a normal user.
I tried to download adb but i dont understand it much, and also it cannot find my device.
Is there any way how to still fix my phone or is it completely lost
If so, I please you for a dummies step-by-step list .
Thank you so much in advance. :crying:
So good news,
I managed to load img back with dd application.
My Download mode together with factory reset is working.
I have tried to flash it with LGUP and even with some accused usb disconnections I probably managed to flash new lollipop to my phone.
Now it is optimalizing apps to load android correctly. Only issue I have is low battery, it always drains it too quickly so it cannot load properly.
Any idea how to charge the battery? Every time I connect phone with usb cable it starts up into boot, possible bootloop (cannot say if it is because of low battery or real bootloop)
Thanks
Dude try to install crdroid 7.1.2 nougat rom of d802 this will fix your battery problem
root it and install TWRP with srktools 2.0
this is best way to root G2 5.0.1 lolipop
you can also use LG One Click Root to obtain root then don't update su binary and install Autorec of you model to get twrp
nudget said:
Hello guys!
Unfortunately I have managed to full brick my phone which has worked without any issues for more then 3 years.
My story:
1. Phone started to have random restarts, basicaly, when phone lagged little bit - it restarted phone.
2. When I did manual restart, I got into bootloop and could not get out
3. With a heavy heart I did a factory reset. - Problem with random restarts ontinued together with random bootloops.
4. Did maybe 5 more factory resets, nothing happened.
5. Found a tutorial to flash new firmware.I was on 5.0.2 D802 30d so I used same. (PC suite could not find my phone and LG support tool always freezed on SW install)
6. I used LG Flash tool with normal flash. - used *.kdz which I have downloaded via LG support tool - checked size with dl from source from xda and they were same so i used it.)
7. All success, but device keep restarting - i think no bootloop anymore.
8. I did full flash again with LG flash tool so have a clean install and hopefully fix everything.
9. Suddenly mid-install my phone auto-disconnected from laptop and even with Retry attemps I wasnt able to get it running again. Then my phone restarted itself and that was it.
Now I cannot go to recovery mode, I cannot go to Download mode, all I see is black screen (turns some light on little bit underneath but no data visible).
Also when connect to my Windows 10 laptop multiple discs trying to load and trying to format disk. (one of them contains folder image with some files inside).
I dont have root, I dont have any other tools installed on my phone, just a normal user.
I tried to download adb but i dont understand it much, and also it cannot find my device.
Is there any way how to still fix my phone or is it completely lost
If so, I please you for a dummies step-by-step list .
Thank you so much in advance. :crying:
Click to expand...
Click to collapse
You can fix using qhslb 2.0
You can find video on YouTube.
Hello ..
i have samsung s6 edge + ( sm-g928f ) i love this device and been using it since 3 years ..
yesterday i wonted to root it but couldn't so i road about that and i had to turn off the OEM
after root was every thing good until i enable OEM and restart the device ..
it stak in boot screen with red line ( Binary Blocked by FRP Lock on )
i didn't knew what i should do so i try every thing i know to backup the file i couldn't ,,
finally i fleshed a stocked ROM from Sammobiel and plug it in the charging cable and installed every thing i need from store ..
after that Evey time i unplug the phone from phone 10 sec freeze and turn off so i flashed second time another ROM and third from sammobile
if the phone was unplug and i turn it on when i get the phone menu restart immediately
i tried safe mode the same
what i the problem is it from firmware of from device ( ic ,battery , charging port or .. )
everything work fine when i plug the phone
The main cause would probably be the software, try clearing out all the files in the twrp recovery then reinstall the os, if you still see the same issue after that it would be hardware then
Most likely battery is faulty.
"FRP tool hyjacker" works for me.