Okay guys, I have screwed up...
I will try to explain my situation as thoroughly as possible:
So there was a game promotion that if you had an S6/EDGE, you would get free content in that game. The only way (to me) that I could get it was change my ro.device.model number to appropriate S6 model number to fake having an S6/EDGE. I rooted my Note 4 (SM-N910P) using chainfire's auto-root. Everything went fine inthe rooting process. I downloaded the application that changes my build.prop (In play store it is titled "build.prop editor"). So I changed the ro.device.model to SM-G920F. I restarted my device so the game could notice that I "had" G6/EDGE. I was stuck in a bootloop. All I see is the Samsung logo. I can access download mode (power home voldown) and recovery (power home volup). I was freaking out that I was stuck in a bootloop. Then someone else in the reddit thread (reddit dot com/r/hearthstone/comments/3dkwew/how_to_get_the_samsung_s6_3_packs_and_card_back) said that he tried it on his Note 4 and he also got the same bootloop but he fixed it by reverting back through stock. I downloaded stock Note 4 4.4.4 firmware and flashed....
here are the logs: <ID:0/006> Added!!
<ID:0/006> Removed!!
<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> aboot.mbn
<ID:0/008> NAND Write Start!!
<ID:0/008> sbl1.mbn
<ID:0/008> rpm.mbn
<ID:0/008> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
and on my phone: UDC start
SW Rev Check FAIL: [aboot] Fuused 2 > Binary 1
[1] eMMC write fail: ABOOT
I am screwed, aren't I?
savev1 said:
Okay guys, I have screwed up...
I will try to explain my situation as thoroughly as possible:
So there was a game promotion that if you had an S6/EDGE, you would get free content in that game. The only way (to me) that I could get it was change my ro.device.model number to appropriate S6 model number to fake having an S6/EDGE. I rooted my Note 4 (SM-N910P) using chainfire's auto-root. Everything went fine inthe rooting process. I downloaded the application that changes my build.prop (In play store it is titled "build.prop editor"). So I changed the ro.device.model to SM-G920F. I restarted my device so the game could notice that I "had" G6/EDGE. I was stuck in a bootloop. All I see is the Samsung logo. I can access download mode (power home voldown) and recovery (power home volup). I was freaking out that I was stuck in a bootloop. Then someone else in the reddit thread (reddit dot com/r/hearthstone/comments/3dkwew/how_to_get_the_samsung_s6_3_packs_and_card_back) said that he tried it on his Note 4 and he also got the same bootloop but he fixed it by reverting back through stock. I downloaded stock Note 4 4.4.4 firmware and flashed....
here are the logs: <ID:0/006> Added!!
<ID:0/006> Removed!!
<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> aboot.mbn
<ID:0/008> NAND Write Start!!
<ID:0/008> sbl1.mbn
<ID:0/008> rpm.mbn
<ID:0/008> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
and on my phone: UDC start
SW Rev Check FAIL: [aboot] Fuused 2 > Binary 1
[1] eMMC write fail: ABOOT
I am screwed, aren't I?
Click to expand...
Click to collapse
try download diffrent firmware
try wipe data/cache (volum up+power button +home button) if you cant access it .try rooting your device and then install recovery then wipe(cache data) and try flashing stocks firmware again
it may also be bad cable try diffrent one
reinstall kies 3(after unistalling it first)
use diffrent odin (3.04 ECT)
and try kikat firmware i believe its just firmware issue (try russian kitkat if your device varient is supported )
savev1 said:
Okay guys, I have screwed up...
I will try to explain my situation as thoroughly as possible:
here are the logs: <ID:0/006> Added!!
<ID:0/006> Removed!!
<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> aboot.mbn
<ID:0/008> NAND Write Start!!
<ID:0/008> sbl1.mbn
<ID:0/008> rpm.mbn
<ID:0/008> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
and on my phone: UDC start
SW Rev Check FAIL: [aboot] Fuused 2 > Binary 1
[1] eMMC write fail: ABOOT
I am screwed, aren't I?
Click to expand...
Click to collapse
No youre not screwed(shouldnt be).
And No, dont continue to flash KitKat firmware or youre going to be wasting time and continually disappointed, no matter how many times you download it.
Once you get to a certain bootloader, youre not able to downgrade to prior(kitkat in this case) bootloaders. Flash the LATEST stock.tar through Odin and start all over.
xxSTARBUCKSxx said:
No youre not screwed(shouldnt be).
And No, dont continue to flash KitKat firmware or youre going to be wasting time and continually disappointed, no matter how many times you download it.
Once you get to a certain bootloader, youre not able to downgrade to prior(kitkat in this case) bootloaders. Flash the LATEST stock.tar through Odin and start all over.
Click to expand...
Click to collapse
Ummm, okay could you possibly link my to the current tars? I have tried flashing everything from kitkat to lollipop. (I was originally on the BOB7 lollipop build).)
From what I've read (hence why I am scared) is that my eMMC chip is broken and cannot be written to...
savev1 said:
Ummm, okay could you possibly link my to the current tars? I have tried flashing everything from kitkat to lollipop. (I was originally on the BOB7 lollipop build).)
From what I've read (hence why I am scared) is that my eMMC chip is broken and cannot be written to...
Click to expand...
Click to collapse
Well, lets hope that isnt the case and stick to what we do know. That message you received points to one thing, Trying to Odin a .tar firmware that contains an older bootloader that people with OE1 and up bootloaders cannot downgrade to.
OF5 Stock tar.
http://forum.xda-developers.com/note-4-sprint/general/of5-tar-t3158006
FYI SM-N910P Forum
http://forum.xda-developers.com/note-4-sprint
xxSTARBUCKSxx said:
Well, lets hope that isnt the case and stick to what we do know. That message you received points to one thing, Trying to Odin a .tar firmware that contains an older bootloader that people with OE1 and up bootloaders cannot downgrade to.
OF5 Stock tar.
http://forum.xda-developers.com/note-4-sprint/general/of5-tar-t3158006
FYI SM-N910P Forum
http://forum.xda-developers.com/note-4-sprint
Click to expand...
Click to collapse
It worked! It worked! I pressed thanks bro ^.^
savev1 said:
It worked! It worked! I pressed thanks bro ^.^
Click to expand...
Click to collapse
Lol. Np bro. Glad it worked. Thats what the community is here for.
Get your phone situated and the way you like it (launchers or what have you) and make a backup in recovery and youll be good to go.
Note 4 sm-n910f
savev1 said:
It worked! It worked! I pressed thanks bro ^.^
Click to expand...
Click to collapse
I've been had the same problem having this error
----------------------
UDC start
SW Rev Check FAIL: [aboot] Fuused 2 > Binary 1
[1] eMMC write fail: ABOOT
-----------------------
and I badly need to flash to stock since I am using custom and having problem with my sim not being detected .
but i just cant seem to get it flashed once more like i did the first try with a stock rom ?
would you suggest me to download several stock rom in sammobile and try all.
I am having the same problem with N910W8 getting emmc write fail
Related
Things started after rooting my galaxy y.
I root galaxy y. After that i was trying to update this into jellyblast. But it stuck at the middle of it after reboot i found that mobile drop down menu also gone. Now i only have one way to go. Format mobile. But when i tried wipe data it return me an error E: not able to mount.
Now i was trying to restore it via odin3 V1.85 but it stuck there also.
I am getting an error.
"<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> boot.img
<ID:0/008> NAND Write Start!!
<ID:0/008>
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
"
what to do??
I am not using kies etd.
devprakash said:
Things started after rooting my galaxy y.
I root galaxy y. After that i was trying to update this into jellyblast. But it stuck at the middle of it after reboot i found that mobile drop down menu also gone. Now i only have one way to go. Format mobile. But when i tried wipe data it return me an error E: not able to mount.
Now i was trying to restore it via odin3 V1.85 but it stuck there also.
I am getting an error.
"<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> boot.img
<ID:0/008> NAND Write Start!!
<ID:0/008>
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
"
what to do??
I am not using kies etd.
Click to expand...
Click to collapse
Mh...... odd
Sent from my LG-LS970 using xda app-developers app
devprakash said:
Things started after rooting my galaxy y.
I root galaxy y. After that i was trying to update this into jellyblast. But it stuck at the middle of it after reboot i found that mobile drop down menu also gone. Now i only have one way to go. Format mobile. But when i tried wipe data it return me an error E: not able to mount.
Now i was trying to restore it via odin3 V1.85 but it stuck there also.
I am getting an error.
"<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> boot.img
<ID:0/008> NAND Write Start!!
<ID:0/008>
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
"
what to do??
I am not using kies etd.
Click to expand...
Click to collapse
Sorry, but you can't mention the name of banned roms here. Anyway, try to install USB drivers for Galaxy Y here. If you can boot your phone, enable USB Debugging in Settings> Applications> Development. Make sure to download stock firmware from here: http://forum.xda-developers.com/showthread.php?t=1465800 and flash it via Odin.
luqman98 said:
Sorry, but you can't mention the name of banned roms" here. Anyway, try to install USB drivers for Galaxy Y here. If you can boot your phone, enable USB Debugging in Settings> Applications> Development. Make sure to download stock firmware from here: http://forum.xda-developers.com/showthread.php?t=1465800 and flash it via Odin.
Click to expand...
Click to collapse
What you mean by "Banned roms"
2. Samsung USB driver already installed.
i already downloaded stock firmware " S5360_DDLA3_ODDLA2_DDLA2 (revision 1) " Asia
devprakash said:
What you mean by "Banned roms"
2. Samsung USB driver already installed.
i already downloaded stock firmware " S5360_DDLA3_ODDLA2_DDLA2 (revision 1) " Asia
Click to expand...
Click to collapse
Banned roms are ROMs that are banned by xda members. It is caused by violating xda rules. Example, Jellyblast rom were banned because Avijit (creator) linking to a download which took you to an ad site and Nemesis is banned because containing warez and steal other's work.
better to install kies first
devprakash said:
What you mean by "Banned roms"
2. Samsung USB driver already installed.
i already downloaded stock firmware " S5360_DDLA3_ODDLA2_DDLA2 (revision 1) " Asia
Click to expand...
Click to collapse
If u have latest samsung drivers, then u should not get error... i'll advice to download latest kies from the samsung site.... install it... & then try odin..
i faced this problem long ago, & solved by this way...
as u know, dont use pit file.. dont clck on repartition...
best luck
devprakash said:
Things started after rooting my galaxy y.
I root galaxy y. After that i was trying to update this into jellyblast. But it stuck at the middle of it after reboot i found that mobile drop down menu also gone. Now i only have one way to go. Format mobile. But when i tried wipe data it return me an error E: not able to mount.
Now i was trying to restore it via odin3 V1.85 but it stuck there also.
I am getting an error.
"<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> boot.img
<ID:0/008> NAND Write Start!!
<ID:0/008>
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
"
what to do??
I am not using kies etd.
Click to expand...
Click to collapse
Use newer versions of Odin like Odin 3.0+
And make sure adb.exe/Kies.exe/Kiesxxxxxxxxxx.exe r not running
devprakash said:
Things started after rooting my galaxy y.
I root galaxy y. After that i was trying to update this into jellyblast. But it stuck at the middle of it after reboot i found that mobile drop down menu also gone. Now i only have one way to go. Format mobile. But when i tried wipe data it return me an error E: not able to mount.
Now i was trying to restore it via odin3 V1.85 but it stuck there also.
I am getting an error.
"<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> boot.img
<ID:0/008> NAND Write Start!!
<ID:0/008>
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
"
what to do??
I am not using kies etd.
Click to expand...
Click to collapse
Question:
Is this your first time flashing Odin?
Yes: Then first install KIES, but your stock driver is preferable (you know.. the one that comes with the box) to avoid incompatibilities, the install odin; i personally use Odin3 v1.85 and it has never failed me once.. and I have tried almost every ROM and kernel for Y. Close KIES before flashing.
No, I have done this before: Did you try another USB port or another computer? Assuming you didnt interchange the 3 files when flashing, did you remove the battery and let the fone discharge for atleast 1 minute and also did you remove the SD card. Sometimes there are files and script from your custom Roms that messes with odin so remove SD card prior to flashing.
There is another method you can do, I myself have used this twice to get out of a quite sticky softbrick... but I do not recommend it, Using a totoro pit file. If all other method fails this will MAY get you out
1. after placing PDA, MODEM and CSC... put the totoro pit file on "PIT", LEAVE BOOTLOADER ALONE!!!
2. Click repartition and NOTHING ELSE!!!
3. Click start
4. Hope for the best:fingers-crossed::fingers-crossed::fingers-crossed:
devprakash said:
Things started after rooting my galaxy y.
I root galaxy y. After that i was trying to update this into jellyblast. But it stuck at the middle of it after reboot i found that mobile drop down menu also gone. Now i only have one way to go. Format mobile. But when i tried wipe data it return me an error E: not able to mount.
Now i was trying to restore it via odin3 V1.85 but it stuck there also.
I am getting an error.
"<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> boot.img
<ID:0/008> NAND Write Start!!
<ID:0/008>
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
"
what to do??
I am not using kies etd.
Click to expand...
Click to collapse
did u install drivers of ur phone and started odin as administrator
As stated by a user above that make sure adb, kies ,any software that uses ur phobes usb is not running....
In odin make sure re-partition is disabled and dont use a pit file
All u need to use is pda,csc,phone,
Not even bootloader
Check whether the usb is nit interupted by anything during the flash...
Sent from my GT-S5360 using xda app-developers app
Extra notes: I took the Verizon Update Last Week while rooted which screwed up my system so I thought I start fresh, that's what caused this whole fiasco.
I'm having some issues here following this guide: http://forum.xda-developers.com/veri...volte-t2879348
I ran into a problem after flashing the vulnerable kernel.
When I tried to flash a full stock rom(or any rom) I get an error in odin:
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
and on the phone
SW REV CHECK FAIL : [aboot] Fused 2 > Binary 1
I can still seem to flash both the kernels in Odin with no issues, and I tried to repartition with the pit file from this thread: http://forum.xda-developers.com/show....php?t=2784880 But still with no luck.
I have a Verizon S5
Booting again!
I found I was able to boot again, but will hold off on rooting again. Here's what I did:
Downloaded Modem and Kernel for OC4 from http://forum.xda-developers.com/show....php?t=2784880
From Odin 10.4 Entered Kernel in PDA and Modem in CP.
Flashed it successfully!
Let it sit at the Verizon Logo for about 5 minutes!
Not sure if I can flash full roms from Odin or not, but I'm relaxing with this for now.
I'm not sure if it may be related to OC4's update blocking downgrading?
Extra Info:
Version: 5.0
Baseband: G900VVRU1BOC4
Kernel: 3.4.0
Build: LRX21T.G900VVRU2BOE1
I am having same fail, I've read that it's due to us taking that last update a week ago, that's impossible to downgrade from or root.
Sent from my SM-G900V using XDA Free mobile app
gerland said:
I am having same fail, I've read that it's due to us taking that last update a week ago, that's impossible to downgrade from or root.
Sent from my SM-G900V using XDA Free mobile app
Click to expand...
Click to collapse
Yeah I did take that update, it screwed up my system so I thought I'd start fresh... may have been a mistake. But I'm up and running now fortunately, I still can't flash any kind of ROM anymore though.
Did you stay on OE1 or OC4?
XNO said:
Did you stay on OE1 or OC4?
Click to expand...
Click to collapse
I'm on OC4
I am running into the same issue. odin won't flash anything. so now I am soft bricked. I tried to flash a stock image and bootloader but it keeps failing.
Hi,
I have a Galaxy S6 Edge and tried to update the ROM a few days ago. ODIN crashed before completing and I am now stuck in the downloading mode
I downloaded the stock firmware from Samsung and when I try to install i get the following message:
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Also the phone has a red message in the left corner: SW REV CHECK FAIL DEVICE:3 BINARY:1
Please Help Me.
agitayuda said:
Hi,
I have a Galaxy S6 Edge and tried to update the ROM a few days ago. ODIN crashed before completing and I am now stuck in the downloading mode
I downloaded the stock firmware from Samsung and when I try to install i get the following message:
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Also the phone has a red message in the left corner: SW REV CHECK FAIL DEVICE:3 BINARY:1
Please Help Me.
Click to expand...
Click to collapse
If you can be more spesific, u will being helped easily. Which variant/baseband/rom/firmware and etc. And check the attached image which is belongs with @xanthrax :good:
S6 Edge or Edge Plus ?
same problem please help
Im getting the same error message when I try to stock flash my regular s6. I have a G920P, I was told the t mobile G920t root would work, but now when I reboot I get the error "recvoery is not seandroid enforcing", and im stuck on the boot loader screen. I got the t mobile flash from aurtoroot. please help im stuck with a bricked phone.
Also have this error - Here is additional info
Hi, I am having this issue too. It sucks, I feel as if I have lost a limb!
I am not so experienced in this area so I will do my best on info:
RP SWREV: B:3 K:2 S:2 - I presume this is the model info and will assist you guys.
I have attached a screenshot of the error I get in Odin. Any help would be greatly appreciated. I am a little worried as this issue appears to be virtually unknown on the internet!
I am a first time poster so having issues sharing link.... hope this works: ht tp://tinypic.com/r/2e0mqu0/9
Thanks,
Adam
Also i am on a Galaxy S6.
r3dfour said:
Im getting the same error message when I try to stock flash my regular s6. I have a G920P, I was told the t mobile G920t root would work, but now when I reboot I get the error "recvoery is not seandroid enforcing", and im stuck on the boot loader screen. I got the t mobile flash from aurtoroot. please help im stuck with a bricked phone.
Click to expand...
Click to collapse
What are firmware are you flashing? You say you have a G920P this is the G928 S6Edge Plus thread
"And on that bombshell!"
Sent from my G928C Rockin AUDAX+ Rom and Eladios themes.
---------- Post added at 01:33 AM ---------- Previous post was at 01:31 AM ----------
fallaize said:
Hi, I am having this issue too. It sucks, I feel as if I have lost a limb!
I am not so experienced in this area so I will do my best on info:
RP SWREV: B:3 K:2 S:2 - I presume this is the model info and will assist you guys.
I have attached a screenshot of the error I get in Odin. Any help would be greatly appreciated. I am a little worried as this issue appears to be virtually unknown on the internet!
I am a first time poster so having issues sharing link.... hope this works: ht tp://tinypic.com/r/2e0mqu0/9
Thanks,
Adam
Also i am on a Galaxy S6.
Click to expand...
Click to collapse
Make sure you have the proper firmware this is the G928 S6Edge Plus thread. Not G920
"And on that bombshell!"
Sent from my G928C Rockin AUDAX+ Rom and Eladios themes.
---------- Post added at 01:39 AM ---------- Previous post was at 01:33 AM ----------
agitayuda said:
Hi,
I have a Galaxy S6 Edge and tried to update the ROM a few days ago. ODIN crashed before completing and I am now stuck in the downloading mode
I downloaded the stock firmware from Samsung and when I try to install i get the following message:
Odin v.3 engine (ID:4)..
File analysis..
SetupConnection..
Initialzation..
Get PIT for mapping..
Firmware update start..
SingleDownload.
sboot.bin
NAND Write Start!!
FAIL!
Complete(Write) operation failed.
All threads completed. (succeed 0 / failed 1)
Also the phone has a red message in the left corner: SW REV CHECK FAIL DEVICE:3 BINARY:1
Please Help Me.
Click to expand...
Click to collapse
If you are stuck in download mode you're not bricked.
Make sure you have the proper firmware downloaded on your computer. Use Odin 3.10.06 Using winzip or similar tool unzip the firmware and you'll see four files.
Open Odin you'll see AP BL CP and CSC place the corresponding files you've unzipped from firmware into those slots and hit start button you should be up and running
agitayuda said:
Hi,
I have a Galaxy S6 Edge and tried to update the ROM a few days ago. ODIN crashed before completing and I am now stuck in the downloading mode
I downloaded the stock firmware from Samsung and when I try to install i get the following message:
Odin v.3 engine (ID:4)..
File analysis..
SetupConnection..
Initialzation..
Get PIT for mapping..
Firmware update start..
SingleDownload.
sboot.bin
NAND Write Start!!
FAIL!
Complete(Write) operation failed.
All threads completed. (succeed 0 / failed 1)
Also the phone has a red message in the left corner: SW REV CHECK FAIL DEVICE:3 BINARY:1
Please Help Me.
Click to expand...
Click to collapse
"And on that bombshell!"
Sent from my G928C Rockin AUDAX+ Rom and Eladios themes.
Hi s7freak, could you please make a screenshot of the four files in odin? I cant find them.
Thank you
Beni
derboiistfly said:
Hi s7freak, could you please make a screenshot of the four files in odin? I cant find them.
Thank you
Beni
Click to expand...
Click to collapse
If you download the official firmware I was able to use the official firmware in the AP slot by itself
"All we know is...He's called the Stig!"
Sent from my Gorgeous G935F
I'm having this exact problem.
I am on a galaxy s6 edge, G925T.
I tried wiping the system and flashing again, nothing worked. I've tried flashing cyanogenmod, and stock rom, but they both give this same error.
The thing that initially broke the phone was trying to use CF-autoroot, and it put it into a bootloop. i was able to install TWRP but that's as far as i've gotten.
I was trying to copy a cyanogenmod zip file onto my phone to install from TWRP, but every time I tried, the transfer failed.
Check Fail Device 3 binary 1
Hi, I need Help with my Samsung Galaxy A7 2018 (SM-A750FN/DS)
I have a frp lock and a oem lock, I flashed the Combination-file on the Phone but it is the U3.
I can not flash any firmeware or combination file.
on the Screen from the Phone, Check fail (Bootloader) Device 3, Binary 1.
Sorry but can anyone Help me?:crying:
So I have been having alot of trouble trying to get my S5 to have root capabilities and ended up soft bricking the thing. I have Odin V3.09 and the stock firmware and it keeps giving me the chain of messages everytime I try to reflash it:
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My phone is A Galaxy S5 verizon version (SM-G900V) running on 5.1 (I believe). I use this phone everyday and need help ASAP.
Verizon bootloader will be locked, I read someone had unlocked it, but never saw anything more come of it
btw919 said:
So I have been having alot of trouble trying to get my S5 to have root capabilities and ended up soft bricking the thing. I have Odin V3.09 and the stock firmware and it keeps giving me the chain of messages everytime I try to reflash it:
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My phone is A Galaxy S5 verizon version (SM-G900V) running on 5.1 (I believe). I use this phone everyday and need help ASAP.
Click to expand...
Click to collapse
Before you do this open your phone, take battery out and note down your serial number.
What I always try at this stage is Kies. Download Kies 3, click Tools > Firmware Upgrade/Initialization and it will ask for your model number and serial number.
Go through with it. It should download the latest stock firmware for your device and it should ask you to plug your phone in and put it in download mode & press next.
This method has recovered me from the worst situations so I hope it works for you!
Shaolin36 said:
Before you do this open your phone, take battery out and note down your serial number.
What I always try at this stage is Kies. Download Kies 3, click Tools > Firmware Upgrade/Initialization and it will ask for your model number and serial number.
Go through with it. It should download the latest stock firmware for your device and it should ask you to plug your phone in and put it in download mode & press next.
This method has recovered me from the worst situations so I hope it works for you!
Click to expand...
Click to collapse
It worked! Thanks for the help!
Here's the Odin log.
<ID:0/008> Added!!
<ID:0/008> Odin engine v(ID:3.1100)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> SingleDownload.
<ID:0/008> recovery.img
<ID:0/008> NAND Write Start!!
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I was trying to unlock my phone before this, before I gave up because I had downloaded the wrong version (5.0.1 UK stock instead of 4.2.2 stock, was trying to use the leaked unlock codes) and then I tried flashing TWRP 3.0.2-0 in Odin 3.10-7 which "Re-Partition" was ticked automatically for some reason and I didn't know. Now my phone is soft-bricked and Odin won't cooperate. Help me please!
I will provide more info as necessary!
Jared20098 said:
Here's the Odin log.
<ID:0/008> Added!!
<ID:0/008> Odin engine v(ID:3.1100)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> SingleDownload.
<ID:0/008> recovery.img
<ID:0/008> NAND Write Start!!
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I was trying to unlock my phone before this, before I gave up because I had downloaded the wrong version (5.0.1 UK stock instead of 4.2.2 stock, was trying to use the leaked unlock codes) and then I tried flashing TWRP 3.0.2-0 in Odin 3.10-7 which "Re-Partition" was ticked automatically for some reason and I didn't know. Now my phone is soft-bricked and Odin won't cooperate. Help me please!
I will provide more info as necessary!
Click to expand...
Click to collapse
Flash a stock rom with .pit file and re-partition checked. Flash a Lollipop rom.
Lennyz1988 said:
Flash a stock rom with .pit file and re-partition checked. Flash a Lollipop rom.
Click to expand...
Click to collapse
Unfortunately that's gonna take a while due to my internet being reeeaaally crappy. It takes 3-4 hrs on average to download a 1.5 GB file.
Try changing the USB ports.I had the same problem like you 1 mouth ago and tried changing from the front USB ports to the back and it worked.
simeon112 said:
Try changing the USB ports.I had the same problem like you 1 mouth ago and tried changing from the front USB ports to the back and it worked.
Click to expand...
Click to collapse
This is an old thread but gotta say LIFE SAVER.
Was flashing pit files left right and center, a simple switch to a USB 2.0 port fixed it. Thanks
Tweakforce_LG said:
This is an old thread but gotta say LIFE SAVER.
Was flashing pit files left right and center, a simple switch to a USB 2.0 port fixed it. Thanks
Click to expand...
Click to collapse
what da heck is a PIT files and where do I get this
Pit files contain partition information about a particular Samsung phone.
Older thread with good information: https://forum.xda-developers.com/showthread.php?t=999097
Israelleite said:
what da heck is a PIT files and where do I get this
Click to expand...
Click to collapse
^^^^
audit13 said:
Pit files contain partition information about a particular Samsung phone.
Older thread with good information: https://forum.xda-developers.com/showthread.php?t=999097
Click to expand...
Click to collapse